The 6-byte protocol supports reporting the position when three fingers
are pressed, exactly like when one finger is pressed. Report this.
In addition, it is also distinguishes between 3 and 4 fingers pressed.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the Dell/Ubuntu driver, what was previously observed as
"jumpy cursor" corresponds to the hardware sending incorrect data for
the first two reports of a one touch finger. So let's use the same
workaround as in the other driver. Also, detect another firmware
version with the same behaviour, as in the other driver.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently there are Elantech touchpads that report non-zero in the 2nd byte
of their signature. Adjust the detection routine so that if 2nd byte is
zero and 3rd byte contains value that is not a valid report rate, we still
assume that signature is valid.
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad7877 - keep dma rx buffers in seperate cache lines
Input: psmouse - reset all types of mice before reconnecting
Input: elantech - use all 3 bytes when checking version
Input: iforce - fix Guillemot Jet Leader 3D entry
Input: iforce - add Guillemot Jet Leader Force Feedback
Apparently all 3 bytes returned by ETP_FW_VERSION_QUERY are significant
and should be taken into account when matching hardware version/features.
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - allow binding to button-only devices
Input: elantech - ignore high bits in the position coordinates
Input: elantech - allow forcing Elantech protocol
Input: elantech - fix firmware version check
Input: ati_remote - add some missing devices from lirc_atiusb
Input: eeti_ts - cancel pending work when going to suspend
Input: Add support of Synaptics Clickpad device
Revert "Input: ALPS - add signature for HP Pavilion dm3 laptops"
Input: psmouse - ignore parity error for basic protocols
In older versions of the elantech hardware/firmware those bits always
were unset, so it didn't actually matter, but newer versions seem to
use those high bits for something else, screwing up the coordinates
we report to the input layer for those devices.
Signed-off-by: Florian Ragwitz <rafl@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently hardware vendors now ship elantech touchpads with different version
magic. This options allows for them to be tested easier with the current driver
in order to add their magic to the whitelist later.
Signed-off-by: Florian Ragwitz <rafl@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The check determining whether device should use 4- or 6-byte packets
was trying to compare firmware with 2.48, but was failing on majors
greater than 2. The new check ensures that versions like 4.1 are
checked properly.
Signed-off-by: Florian Ragwitz <rafl@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Elantech touchpads work in absolute mode and do not generate relative
events so they should not be advertising them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist laptops with Elantech touchpads where switching to absolute mode
does not happen, although writing the configuration register succeeds
without error. Reading back the register afterwards reveils that the
absolute mode bit is not set as if masked out by the touchpad firmware.
Always read back register 0x10, make sure that for hardware version 1 the
absolute mode bit is actually set and fail otherwise. This prevents the case
where the touchpad is claimed by the Elantech driver but is nonetheless not
working.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that Elantech touchpad firmware version 2.34 on the Hercules eCAFÉ
suffers from a problem where bogus coordinates get reported at the beginning
of a touch action. This causes the mouse cursor or the scrolled page to
jump.
Included patch provides a workaround that discards mouse packets that are
likely to contain bogus coordinates. The workaround is activated when we
detect touchpad with fimware version 2.34.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some Logitech mice react to the magic knock like Elantech touchpad would.
This leads to those mice being misdetected as Elantech touchpads. Add a
version query to elantech_detect() to distinguish the two.
[dtor@mail.ru:
- lower severity of some messages - when we are not sure yet if
device is Elantech or not not responding to knock is not an error.
]
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is version 5 of the driver. Relative mode support has been
dropped (users wishing to use touchpad in relative mode can use
standard PS/2 protocol emulation done in hardware). The driver
supports both original version of Elantech protocol and the newer
one used by touchpads installed in EeePC.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Éric Piel