This removes calls to get the device via PCI from other parts of the
code that will be able to be re-used by the platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will allow for a platform hda driver to use it as well. It
removes the dependency on the module param from hda_intel, which will
allow for azx_setup_periods to be shared.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The forthcoming platform hda driver needs to override the way
registers are read and written. In preparation for that, introduce a
reg_ops struct that can be implemented differently by the new driver.
Change the existing macros to use the new structure, and move them to
hda_priv.h where they will be accessible to both PCI and platform
drivers.
Start with register access, but later commits will add more ops that
differ between PCI and platform.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Later commits adding support for hda platform drivers will want to use
the same defines and structures. Put them in a place reachable by both
hda_intel and the new platform driver.
This is a mostly a direct copy with a few whitespace and comment
changes to make checkpatch happy.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA spec, we must write 1 to bit 15 on a CORBRP
reset, read back 1, then write 0, then read back 0. This must be
done while the DMA is not running.
We accidentaly ended up writing back the 0 by using a writel
instead of a writew to CORBWP.
This caused occasional controller failure on Bay Trail hardware.
[replaced error messages with dev_err() by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep input device is registered via input_register_device(), but
this is called in snd_hda_attach_beep_device() where the sound devices
aren't registered yet. This leads to the binding to non-existing
object, thus results in failure. And, even if the binding worked
(against the PCI object), it's still racy; the input device appears
before the sound objects.
For fixing this, register the input device properly at dev_register
ops of the codec object it's bound with. Also, call
snd_hda_detach_beep_device() at dev_disconnection so that it's
detached at the right timing. As a bonus, since it's called in the
codec's ops, we can get rid of the further call from the other codec
drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many HP laptops with STAC codecs have a docking station port and BIOS
sets the pins for the input on the dock as a line in. Because the
generic parser doesn't handle a line in pin as auto-switchable, this
resulted in the manual capture source selection on these laptops.
However, from the usability POV, the automatic switching is easier.
This patch adds the line_in_auto_switch hint in the fixup function for
these laptops. Even if no dock port is present, this should be
harmless as the generic parser allows the auto-switching only in a
limited situation (all three pins are located in different
positions).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the controller, the new codec object is assigned as a
parent for the hd-audio beep input devices, just like already done for
PCM and hwdep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
The debug prints are also reformatted to suit with dev_dbg().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
Some commented debug prints are also enabled as dev_dbg().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
All debug print macros have been replaced with dev_dbg(), too.
Also, added the missing definition of snd_azf3328_ctrl_inw().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use dev_err() and co for messages from HD-audio controller and codec
drivers. The codec drivers are mostly bound with codec objects, so
some helper macros, codec_err(), codec_info(), etc, are provided.
They merely wrap the corresponding dev_xxx().
There are a few places still calling snd_printk() and its variants
as they are called without the codec or device context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some sysfs attributes like init_pin_configs or vendor_name are really
basic and should be available no matter whether the codec driver is
re-configurable or not. Put them out of #ifdef
CONFIG_SND_HDA_RECONFIG and allow the read-only accesses.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have currently sysfs attributes for each hwdep, but basically these
should belong to the codec itself, per se. Let's add them to the
codec object while keeping them for hwdep as is for compatibility.
While we are at it, split the sysfs-related stuff into a separate
source file, hda_sysfs.c, and keep only the stuff necessary for hwdep
in hda_hwdep.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the HD-audio is treated individually in each codec driver, it's
more convenient to assign an own struct device to each codec object.
Then we'll be able to use dev_err() more easily for each codec, for
example.
For achieving it, this patch just creates an object "hdaudioCxDy".
It belongs to sound class instead of creating a new bus, just for
simplicity, at this stage. No pm ops is implemented in the device
struct level but currently it's merely a container. The PCM and hwdep
devices are now children of this codec device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now each snd_hda_codec instance is managed via the device chain, the
registration and release are done by its callback instead of calling
from bus.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For referring to a different object from sysfs ops, take hwdep
private_data as stored via dev_set_drvdata() at creating the device
object. In that way, the same sysfs ops can be used by different
device types.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling each time device_create_file(), create the groups
of sysfs attribute files at once in a normal way. Add a new helper
function, snd_get_device(), to return the associated device object,
so that we can handle the sysfs addition locally.
Since the sysfs file addition is done differently now,
snd_add_device_sysfs_file() helper function is removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GPIO line used for the mute LED control on Lenovo Yxx0 laptops is
cleared unexpectedly when the codec goes to D3, typically by
power-saving. For avoiding it, add a power filter in the fixup.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Folio 13 may have a broken BIOS that doesn't set up the mute LED
GPIO properly, and the driver guesses it wrongly, too. Add a new
fixup entry for setting the GPIO pin statically for this laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70991
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The front headphone and mic jackes on a HP desktop model (Vendor Id:
0x111d76c7 Subsystem Id: 0x103c2b17) can not work, the codec on this
machine has 8 physical ports, 6 of them are routed to rear jackes
and all of them work very well, while the remaining 2 ports are
routed to front headphone and mic jackes, but the corresponding
pin complex node are not defined correctly.
After apply this fix, the front audio jackes can work very well.
[trivial fix of enum definition by tiwai]
BugLink: https://bugs.launchpad.net/bugs/1282369
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Gerald Yang <gerald.yang@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorrect ADC is picked in ca0132_capture_pcm_prepare(),
where it assumes multiple streams while there is one stream
per ADC. Note that ca0132_capture_pcm_cleanup() already does
the right thing.
The Chromebook Pixel has a microphone under the keyboard that
is attached to node id 0x8. Before this fix, recording would
always go to the main internal mic (node id 0x7).
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a HDMI stream is opened with the same stream tag
as a following opened stream to ca0132, audio will be
heard from two ports simultaneously.
Fix this issue by change to use snd_hda_codec_setup_stream
and snd_hda_codec_cleanup_stream instead, so that an
inactive stream can be marked as 'dirty' when found
with a conflict stream tag, and then get purified.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Chih-Chung Chang <chihchung@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machines (Vendor ID:
0x10ec0255, Subsystem ID: 0x10280657; Vendor ID: 0x10ec0255,
Subsystem ID: 0x1028065f), the headset mic can't be
detected, after apply this patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Realtek codec driver contains some codes referring to the PCI
subdevice IDs, but most of them are optional, typically for checking
the codec name variants. Add NULL checks appropriately so that it can
work without PCI assignment.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default parent device can be obtained directly via card object, so
we don't need to rely on pci->dev.parent. Since there is no access to
pci_dev, we can reduce the inclusion of linux/pci.h, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit d3c56568f4.
The reverted commit breaks audio through headphone line out on
the Acer TravelMate B113 (Type1Sku0) Notebook, my main work
machine. I don't know much about it but this fixes my problem.
Bisected and tested.
Fixes: d3c56568f4 ('ALSA: hda/realtek - Avoid invalid COEFs for ALC271X')
Cc: <stable@vger.kernel.org>
Tested-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last user of snd_hda_gen_spec_free() is patch_via.c, and we can
rewrite it safely with snd_hda_gen_free(), so that
snd_hda_gen_spec_free() can be a local function in hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to alsa-info.sh outputs, all three entries with static
quirks have the correct pin configs, so it's safe to remove static
quirks. For now, turn the static quirks off via ifdef. The dead
codes will be removed in later release.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even after the fix for leftover kconfig handling (commit f8f1becf),
the current code still doesn't handle properly the builtin/module
mixup case between the core snd-hda-codec and other codec drivers.
For example, when CONFIG_SND_HDA_INTEL=y and
CONFIG_SND_HDA_CODEC_HDMI=m, it'll end up with an unresolved symbol
snd_hda_parse_hdmi_codec. This patch fixes the issue.
Now codec->parser points to the parser object *only* when a module
(either generic or HDMI parser) is loaded and bound. When a builtin
symbol is used, codec->parser still points to NULL. This is the
difference from the previous versions.
Fixes: f8f1becfa4 ('ALSA: hda - Fix leftover ifdef checks after modularization')
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the lengthy #if defined(XXX) || defined(XXX_MODULE) with the
new IS_ENABLED() macro.
The patch still doesn't cover all ifdefs. For example, the dependency
on CONFIG_GAMEPORT is still open-coded because this also has an extra
dependency on MODULE. Similarly, an open-coded ifdef in pcm_oss.c and
some sequencer-related stuff are left untouched.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove unused function in pci/lx6464es/lx_core.c.
This eliminates the following warning in pci/lx6464es/lx_core.c:
sound/pci/lx6464es/lx_core.c:144:5: warning: no previous prototype for ‘lx_plx_mbox_read’ [-Wmissing-prototypes]
sound/pci/lx6464es/lx_core.c:172:5: warning: no previous prototype for ‘lx_plx_mbox_write’ [-Wmissing-prototypes]
sound/pci/lx6464es/lx_core.c:494:5: warning: no previous prototype for ‘lx_dsp_es_check_pipeline’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bug reporter report that the -mode4 makes the subwoofer work.
I have simplified the quirk a bit to avoid possible regressions
with the microphones.
BugLink: https://bugs.launchpad.net/bugs/871808
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a small refactoring to make the next patch slightly simpler.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The very same fixup is needed to make the mic on Sony VAIO Pro 11
working as well as VAIO Pro 13 model.
Reported-and-tested-by: Hendrik-Jan Heins <hjheins@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code for controlling mic mute LED in patch_sigmatel.c
blindly assumes that there is a single capture switch. But, there can
be multiple multiple ones, and each of them flips the state, ended up
in an inconsistent state.
For fixing this problem, this patch adds kcontrol to be passed to the
hook function so that the callee can check which switch is being
accessed. In stac_capture_led_hook(), the state is checked as a
bitmask, and turns on the LED when all capture switches are off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the commit [595fe1b702c3: ALSA: hda - Make
CONFIG_SND_HDA_CODEC_* tristate], the kconfig variables for the
generic parser and codec drivers can be "m" instead of boolean, but
some codes are left unchanged to check only #ifdef
CONFIG_SND_HDA_CODEC_XXX, which is no longer true for modules.
This patch fixes them by replacing with IS_ENABLED() macros.
Fixes: 595fe1b702 ('ALSA: hda - Make CONFIG_SND_HDA_CODEC_* tristate')
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70161
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1983 has flexible loopback routes and the generic parser would take
wrong path confusingly instead of taking individual paths via NID 0x0c
and 0x0d. For avoiding it, limit the connections at these widgets so
that the parser can think more straightforwardly. This fixes the
regression of the missing line-in loopback on Dell machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70011
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mac Pro 1,1 with ALC889A codec needs the VREF setup on NID 0x18 to
VREF50, in order to make the speaker working. The same fixup was
already needed for MacBook Air 1,1, so we can reuse it.
Reported-by: Nicolai Beuermann <mail@nico-beuermann.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer widget on AD1983 at NID 0x0e was missing in the commit
[f2f8be43c5c9: ALSA: hda - Add aamix NID to AD codecs].
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70011
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've seen often problems after suspend/resume on Acer Aspire One
AO725 with ALC271X codec as reported in kernel bugzilla, and it turned
out that some COEFs doesn't work and triggers the codec communication
stall.
Since these magic COEF setups are specific to ALC269VB for some PLL
configurations, the machine works even without these manual
adjustment. So, let's simply avoid applying them for ALC271X.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite L40 with AD1986A codec requires the EAPD of NID 0x1b
to be constantly on, otherwise the output doesn't work.
Unlike most of other AD1986A machines, EAPD is correctly implemented
in HD-audio manner (that is, bit set = amp on), so we need to clear
the inv_eapd flag in the fixup, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67481
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Ideapad with ALC272 has a mute LED that is controlled via
GPIO1. Add a simple vmaster hook for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 384a48d715 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!
However, this apparently broke some Intel systems, and commit
6169b67361 "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.
This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.
Reported-by: Uosis <uosisl@gmail.com>
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While looking into some spurious responses, I found that the addr value was
treated a bit inconsistent: values 8..0xf will be treated as codec 0 and
values 0..7 will be treated as no error regardless of whether there is a codec
there, or not.
With this patch, all non-existing codecs will be treated equally.
In addition, printing rp and wp could help figuring out if the wp value is
reported wrongly from the controller or if something else is wrong.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now all weird setups have been converted to fixups for the generic
parser, and we can disable the static quirks. This commit just turns
the build off. The bulky static quirk code still remains for a while,
in case we get an overlooked regression. It'll be removed at the next
kernel version.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both CX20549 and CX20551 codecs have a mixer widget and it can be
connected as the ADC source. Like AD and VIA codecs, enable the
add_stereo_mix_input flag for these codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OLPC XO needs a few special handling. Now these are implemented as a
fixup to the generic parser.
Obviously, the DC BIAS mode had to be added manually. This is mainly
implemented in the mic_autoswitch hook, where the mic pins are
overwritten depending on the DC bias mode. This also required the
override of the mic boost control, since the mic boost is applied only
when the DC mode is disabled.
In addition, the mic pins must be set dynamically at recording time
because these also control the LED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... by using snd_Hda_codec_update_cache() instead of *_write_cache().
Since all path elements should have been updated by this function,
we are safe to assume that the cache contents are consistent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (Vendor ID:
0x10ec0255, Subsystem ID: 0x1028064d), the headset mic can't be
detected, after apply this patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Doro Wu <fan-cheng.wu@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This completes the hardware support for the Asus Xonar DG/DGX cards,
and makes them actually usable.
This is v4 of Roman's patch set with some small formatting changes.
Remove old SPI control functions, change anti-pop init
sequence, remove some garbage from structures. The 'Apply' functions
must be called at the mixer initialization, otherwise
mixer settings sometimes will not be applied at startup.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the 'put' function of the high-pass filter control to use the new
SPI functions.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
First of all, we should not touch the GPIOs. They are not
for selecting the capture source, but they seems just enable
the whole audio input curcuit. The 'put' function calls the
'apply' functions to change register values. Change the order
of capture sources.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modify the input_vol_* functions to use the new SPI routines,
There is a new applying function that will be called when
the capture source changed.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
I tried both variants: volume control and impedance selector.
In the first case one minus is that we can't change the
volume of multichannel output without additional software
volume control. However, I am using this variant for the
last three months and this seems good. All multichannel
speaker systems have internal amplifier with the
volume control included, but not all headphones have
this regulator. In the second case, my software volume
control does not save the value after reboot.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the order of elements in the output select control. This will
reduce the number of relay switches. Change 'put' function to call the
oxygen_update_dac_routing() function. Otherwise multichannel playback
does not work. Also there is a new function to apply settings, this
prevents from duplicating the code.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Actually CS4245 connected to the I2S channel 1 for
capture, not channel 2. Otherwise capturing and
playback does not work for CS4245.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Moving the mixer code away makes things easier. The mixer
will control the driver, so the functions of the
driver need to be non-static.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the function to read the data from the new shadow buffer.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When selecting the audio output destinations (headphones,
FP headphones, multichannel output), the channel routing
should be changed depending on what destination selected.
Also unnecessary I2S channels are digitally muted. This
function called when the user selects the destination
in the ALSA mixer.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When selecting the audio sample rate for CS4245,
the MCLK divider should also be changed.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change CS4245 initialization: different sequence and GPIO values,
according to datasheets and reverse-engineering information.
Change cleanup/resume/suspend functions, since they use
initialization.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add the new SPI write and read functions. The SPI read function
is used for creating initial registers dump and may be used for
debugging purposes. SPI operations are cached, so there is a new
function to manage the cache (shadow). I have to remove
the shift from the CS4245_SPI_* constants, since when
we are performing the reading, we need to shift by 8 instead
of 16.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add additional constants to the xonar_dg.h file:
capture and playback sources. Move GPIO_* constants and the
dg struct to the header file from the xonar_dg.c file.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add some additional information in comments and my copyright.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When the user switches the output from stereo to multichannel
or vice versa, the driver needs to update the channel routing.
Instead of creating additional subroutines, I better export existing
oxygen_update_dac_routing symbol from the oxygen mixer
and call this function. It calls model.adjust_dac_routing()
and my function does the work.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The Xonar DG/DGX driver needs this mask to mute unnecessary
channels.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modify the oxygen_write_spi() function to use the newly
introduced oxygen_wait_spi() function. Change return value
from void to int, so it can return error codes. Older
drivers just ignore that return value, new drivers can
check this value. We need to wait AFTER
initiating the SPI transaction, otherwise read
operation will not work.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The oxygen_wait_spi() function now performs waiting when the
SPI bus completes a transaction. Introduce the timeout error
checking and increase timeout to 200 from 40.
Signed-off-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Processing coefficients are often a vital part of the codec's configuration,
so dumping them can be important. However, because they are undocumented and
secret, we do not want to enable this for all codecs by default.
Therefore instead add this as a debugging parameter.
I have prepared for codecs that want to enable this by default by the extra
dump_coef bitfield, but unsure if we want to do that as long as the
(unlikely, but still) race remains.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly to other Apple products, MBA 1,1 needs a specific quirk.
Pin 0x18 must be set to VREF_50 to have sound output. This was no
longer done since commit 1a97b7f, resulting in a mute built-in speaker.
This patch corrects the regression by creating a fixup for the MBA 1,1.
Fixes: 1a97b7f227 ("ALSA: hda/realtek - Remove the last static quirks for ALC882")
Cc: <stable@vger.kernel.org> [v3.4+]
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Zenbook UX31A has yet another problem -- softer output level than
others. According to the measurement, the peak output difference
between 31A and 31E is 5dB. As ALC269VB has a COEF for the class-D
pre-amp, let's apply it for +5dB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on some Dell machines, the headset
mic can't be detected, after apply this patch, the headset mic
can work well on all those machines.
On the machine with the Subsytem ID 0x10280610, if we use
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE, the headset mic can be
detected and work well, but the sound can't be outputed via
headphone anymore, use ALC269_FIXUP_DELL3_MIC_NO_PRESENCE
can fix this problem.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: David Chen <david.chen@canonical.com>
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Tested-by: Shawn Wang <shawn.wang@canonical.com>
Tested-by: Chih-Hsyuan Ho <chih.ho@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new vmaster hook, update_tpacpi_mute_led(), calls the original
vmaster hook, but I forgot to save the original hook function but keep
calling the updated one, which of course results in a stupid endless
loop. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some AIO (All In One) models with the codec alc668
(Vendor ID: 0x10ec0668) on it, when we plug a headphone into the jack,
the system will switch the output to headphone and set the speaker to
automute as well as change the speaker Pin-ctls from 0x40 to 0x00,
this will bring loud noise to the headphone.
I tried to disable the corresponding EAPD, but it did not help to
eliminate the noise.
According to Takashi's suggestion, we use amp operation to replace the
pinctl modification for the automute, this really eliminate the noise.
BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apply the codec->power_filter to the FG nodes in general for reducing
hackish set_power_state ops override in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A). This patch removes the indep_hp flag for such codecs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA. Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Occasionally, on playback stream ringbuffer wraparound, the EMU20K1
hardware will momentarily return 0 instead of the proper current(loop)
address. This patch handles that case, fixing the problem of playback
position corruption and subsequent loss of buffered sound data, that
occurs with some common buffering layout patterns(e.g. multiple
simultaneous output streams with differently-sized or
non-power-of-2-sized buffers).
An alternate means of fixing the problem would be to read the ca
register continuously, until two sequential reads return the same
value; however, that would be a more invasive change, has performance
implications, and isn't necessary unless there are also issues with the
value not being updated atomically in regards to individual bits or
something similar(which I have not encountered through light testing).
I have no EMU20K2 hardware to confirm if the issue is present there,
but even if it's not, this change shouldn't break anything that's not
already broken.
Signed-off-by: Sarah Bessmer <aotos@fastmail.fm>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nowadays we have CMA for obtaining the contiguous memory pages
efficiently. Let's kill the old kludge for reserving the memory pages
for large buffers. It was rarely useful (only for preserving pages
among module reloading or a little help by an early boot scripting),
used only by a couple of drivers, and yet it gives too much ugliness
than its benefit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the device ID for Intel Broadwell display HD-Audio controller,
and applies Haswell properties to this device.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both patch_realtek.c and patch_conexant.c contain the fairy same code
snippet for supporting Thinkpad ACPI LED controls. Split them into
thinkpad_helper.c and include it from both places. Although this
isn't the best approach from the code size POV, the probability for
coexistence of both Realtek and Conexant codecs on a single machine is
pretty low, thus it'll end up with less memory footprint than
splitting to yet another module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints. This makes even me referring back to the
document often. Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead. No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that some AMD HDMI controllers still don't provide
proper values in GCAP register (all zero), and the driver assigns only
one stream in that case, although the connected codec chip supports
more than one stream.
In this patch, the default max number of streams for AMD HDMI
controllers is increased to 8, which should suffice for most use
cases. The overhead by this increase is more azx_dev struct and BDL
allocations, so it's negligible. Of course, if the controller
provides a proper GCAP register, the register value would be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev;
@@
pci_set_power_state(pdev,
- 3
+ PCI_D3hot
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This motherboard seems to have a flaky jack detection - when the
front HP is not present, the jack state quickly switches on and off.
This has been reported by three people in the bug, so I doubt it's
a user error this time.
BugLink: https://bugs.launchpad.net/bugs/1248116
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In this case, there are two DACs, and DAC 0x03 is mono. In order
to make headphones and front speaker use DAC 0x02, and subwoofer use
DAC 0x03, we artificially cut the connection from nodes 0x14 and 0x15
to node 0x03, so they can only use DAC 0x02.
In addition, the 5460 and 5470 differs in the sense that 5470 also
needs a headset mic patch, whereas 5460 has individual detection for
headphone and headset mic.
BugLink: https://bugs.launchpad.net/bugs/1211920
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_ACPI dependent code should include <linux/acpi.h> instead of
directly including <acpi/acpi.h>. This patch cleans up such wrong
inclusions for Thinkpad ACPI users.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a Kconfig of a codec driver doesn't match with the controller
(CONFIG_SND_HDA_INTEL), it'll result in the non-working automatic
probing. Unfortunately kbuild can't give such a restriction, but at
least, it's possible to show a warning if such a condition is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, CONFIG_SND_HDA_CODEC_* kconfigs have been booleans due to
historical reasons. The major reason was that the automatic codec
driver probing wouldn't work if user sets a codec driver as a module
while the controller driver as a built-in. And, another reason was to
avoid exporting symbols of the helper codes when all drivers are built
in.
But, this sort of "kindness" rather confuses people in the end,
especially makes the config refinement via localmodconfig unhappy.
Also, a codec module would still work if you re-bind the controller
driver via sysfs (although it's no automatic loading), so there might
be a slight use case.
That said, better to let people fallen into a pitfall than being too
smart and restrict something. Let's make things straightforward: now
all CONFIG_SND_HDA_CODEC_* become tristate, and all symbols exported
unconditionally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Dell machines with codec whose Subsystem Id is 0x10280640,
no external microphone can be detected when plugging a 3-ring headset.
Using ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix this problem.
The codec (Vendor ID: 0x10ec0255) on the machine belongs to alc_269
family.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Dell machines with codec whose Subsystem Id is 0x10280610,
0x10280629 or 0x1028063e, no external microphone can be detected when
plugging a 3-ring headset. If we add "model=dell-headset-multi" for
the snd-hda-intel.ko, the problem will disappear.
The codecs on these machines belong to alc_269 family.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While enabling these machines, we found we would sometimes lose an
interrupt if we change hardware volume during playback, and that
disabling msi fixed this issue. (Losing the interrupt caused underruns
and crackling audio, as the one second timeout is usually bigger than
the period size.)
The machines were all machines from HP, running AMD Hudson controller,
and Realtek ALC282 codec.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1260225
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1986A codec is a pretty old codec and has really many hidden
restrictions. One of such is that each DAC is dedicated to certain
pin although there are possible connections. Currently, the generic
parser tries to assign individual DACs as much as possible, and this
lead to two bad situations: connections where the sound actually
doesn't work, and connections conflicting other channels.
We may fix this by trying to find the best connections more harder,
but as of now, it's easier to give some hints for paired DAC/pin
connections and honor them if available, since such a hint is needed
only for specific codecs (right now only AD1986A, and there will be
unlikely any others in future).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Dell machines with codec whose Subsystem Id is 0x10280624,
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/bugs/1259790
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case a single HDA card has both HDMI and S/PDIF outputs, the S/PDIF
outputs will have their IEC958 controls created starting from index 16
and the HDMI controls will be created starting from index 0.
However, HDMI simple_playback_build_controls() as used by old VIA and
NVIDIA codecs incorrectly requests the IEC958 controls to be created
with an S/PDIF type instead of HDMI.
In case the card has other codecs that have HDMI outputs, the controls
will be created with wrong index=16, causing them to e.g. be unreachable
by the ALSA "hdmi" alias.
Fix that by making simple_playback_build_controls() request controls
with HDMI indexes.
Not many cards have an affected configuration, but e.g. ASUS M3N78-VM
contains an integrated NVIDIA HDA "card" with:
- a VIA codec that has, among others, an S/PDIF pin incorrectly
labelled as an HDMI pin, and
- an NVIDIA MCP7x HDMI codec.
Reported-by: MysterX on #openelec
Tested-by: MysterX on #openelec
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org> # 3.8+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not all channels have been initialized, so far, especially when aamix
NID itself doesn't have amps but its leaves have. This patch fixes
these holes. Otherwise you might get unexpected loopback inputs,
e.g. from surround channels.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Dell Inspiron 3045 machine (codec Subsystem Id: 0x10280628),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259437
CC: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Dell Optiplex 3030 machine (codec Subsystem Id: 0x10280623),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259435
CC: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since there are more HD-audio compatible codecs, move the definitions
of HD-audio verbs into common header location, include/sound, so that
it can be included cleanly from other drivers than HD-audio driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD and VIA codecs had stereo mixer input enabled as default before
moving to the generic parser, and people think the lack of such a
regression. In this patch, the stereo mixer input is added back to
the input selection if no auto-mic is available, and if it's not
disabled explicitly via hint. This should satisfy most of demands,
i.e. stereo mix on desktop machines like what it worked before, and it
still keeps the new auto-mic feature on laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes the hardware reports LPIB being advanced than POSBUF.
When this happens, the driver adjusts to a positive value by adding
the buffer size. Then the driver detects it as an error (greater than
the period size), and stops the LPIB delay account from this point
on.
When I took a close look at these conditions, the values shown are all
very small numbers, and it'd be better to just ignore these values
instead of discontinuing the LPIB delay correction.
In this patch, the driver checks a negative delay value and ignores if
it's a significantly small error. Currently the threshold is set to
64 frames, but could be smaller.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loopback mixing paths aren't initialized correctly at init
callback. Mostly this is harmless as codecs usually set the mute
state as default, but we still should make sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have blindly assumed that all valid configurations should have
either analog or digital playback, but there can be capture-only
configurations. The parser shouldn't escape in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch skips the default depop delay before D3 for Haswell (10 ms) and
Valleyview2 (100 ms) display codec, to reduce codec suspend time.
The analog part of display audio is implemented in the external display. Some
displays have weak pop noise while others not when suspending, no matter there
is the default delay or not.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've tested the old Dell Vostro 131 with the latest generic parser
and it works just fine, and as a bonus we get better jack detection
features in userspace. Therefore this quirk can be removed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add quirk for Acer Aspire E-572:
- fix external mic
- limit mic boost for internal mic with maximal noise level of -24dB
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 2,1 has a fairly different pin assignment from its brother
MBA 1,1, and yet another quirks are needed for pin 0x18 and 0x19,
similarly like what iMac 9,1 requires, in order to make the sound
working on it.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the case of using jackpoll_ms instead of unsol events, the jack
was correctly detected, but ELD info was not refreshed on plug-in.
And without ELD info, no proper restriction of pcm, which can in turn
break sound output on some devices.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to remove the hp_automute_hook from alc283_fixup_chromebook.
It doesn't need this for other chrome os machine.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch sets a 0ms depop delay in fixup funtion 'alc_fixup_no_depop_delay'.
And Realteck ALC262 applies this on Intel Baytrail BayleyBay platform to reduce
codec suspend time.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create single model for HP.
The headset jack module was difference between other chrome book.
It need to manual control Mic jack detect.
Chrome OS loaded driver by models. Remove old assigned fixup table from
ALC269 fixup list entry.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By trial and error, I found this patch could work around an issue
where the headset mic would stop working if you switch between the
internal mic and the headset mic, and the internal mic was muted.
It still takes a second or two before the headset mic actually starts
working, but still better than nothing.
Information update from Kailang:
The verb was ADC digital mute(bit 6 default 1).
Switch internal mic and headset mic will run alc_headset_mode_default.
The coef index 0x11 will set to 0x0041.
Because headset mode was fixed type. It doesn't need to run
alc_determine_headset_type.
So, the value still keep 0x0041. ADC was muted.
BugLink: https://bugs.launchpad.net/bugs/1256840
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that AD1986A cannot manage the dynamic pin on/off for
auto-muting, but rather gets confused. Since each output has own amp,
let's use it instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ad_vmaster_eapd_hook() needs to handle the inverted EAPD case
properly, too. Otherwise the output gets broken on Lenovo N100 with
AD1986A codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Z35HL laptop also needs the very same fix as the previous one
that was applied to ASUS W7J.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66231
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio devices tend to take long time for finishing the whole
probing procedure. In this patch, the time-consuming part of the
probing procedure, the codec probe and the rest initializations, are
moved in the work, so that they can be done asynchronously in parallel
with probes of other devices.
Since we already have this mechanism in the driver code for the
firmware and i915 request_symbol() stuff, we just need to enable it
always; the resultant patch even reduces more lines, which is an
additional bonus.
Credit goes to David Henningsson, who suggested this workaround.
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the probe of snd-hda-intel driver is deferred due to f/w loading
or the nested module loading, complete_all() should be also delayed
until the initialization really finished. Otherwise, vga-switcheroo
client would start switching before the actual init is done.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that EAPD on NID 0x16 is the only control over all outputs on
HP machines with AD1984A while turning EAPD on NID 0x12 breaks the
output. Thus we need to avoid fiddling EAPD on NID. As a quick
workaround, just set own_eapd_ctrl flag for the wrong EAPD, then
implement finer EAPD controls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66321
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent kernels got regressions on ASUS W7J with ALC660 codec where
no sound comes out. After a long debugging session, we found out that
setting the pin control on the unused NID 0x10 is mandatory for the
outputs. And, it was found out that another magic of NID 0x0f that is
required for other ASUS laptops isn't needed on this machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66081
Reported-and-tested-by: Andrey Lipaev <lipaev@mail.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds 'depop_delay' to struct hda_codec, to indicate a depop delay
time in ms when power-down, in function set_power_state() to D3.
Default value is -1, for a default delay time.
Machine fixup can set a suitable value according to the codec chip and HW audio
design.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch defines a fixup 'alc_fixup_no_depop_delay', which sets alc_spec flag
'no_depop_delay' to indicate skipping delay in Realtek codec suspend/resume.
And Intel Baytrail BayleyBay board applies this fixup to reduce driver
suspend/resume time.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch defines a flag "no_depop_delay" in alc_spec. If this flag is set,
delay in alc_eapd_shutup and alc_resume will be skipped.
Machine-specific fixup can set this flag to reduce suspend/resume time, if
the codec and hardware analog design can avoid pop noise without this delay.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell assigned alias name for more codecs.
ALC3220 ALC3221 ALC3223 ALC3226 ALC3234 ALC3661.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine also has mono output if run through DAC node 0x03.
Cc: stable@vger.kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1256212
Tested-by: David Chen <david.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the previous commit 1f0bbf03cb added the pin config for the bass
speaker, this patch adds the corresponding LFE-only channel map on
ASUS ET2700.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65961
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a fixup entry for the missing bass speaker pin 0x16 on ASUS ET2700
AiO desktop. The channel map will be added in the next patch, so that
this can be backported easily to stable kernels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65961
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This both devices need limit for internal dmic.
[cosmetic change; renamed fixup name by tiwai]
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current generic parser assumes blindly that the volume and mute
amps are found in the aamix node itself. But on some codecs,
typically Analog Devices ones, the aamix amps are separately
implemented in each leaf node of the aamix node, and the current
driver can't establish the correct amp controls. This is a regression
compared with the previous static quirks.
This patch extends the search for the amps to the leaf nodes for
allowing the aamix controls again on such codecs.
In this implementation, I didn't code to loop through the whole paths,
since usually one depth should suffice, and we can't search too
deeply, as it may result in the conflicting control assignments.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65641
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hp mic pin has no VREF bits, the driver forgot to set PIN_IN
bit. Spotted during debugging old MacBook Airs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a headphone jack is configurable as input, the generic parser
tries to make it retaskable as Headphone Mic. The switching can be
done smoothly if Capture Source control exists (i.e. there is another
input source). Or when user explicitly enables the creation of jack
mode controls, "Headhpone Mic Jack Mode" will be created accordingly.
However, if the headphone mic is the only input source, we have to
create "Headphone Mic Jack Mode" control because there is no capture
source selection. Otherwise, the generic parser assumes that the
input is constantly enabled, thus the headphone is permanently set
as input. This situation happens on the old MacBook Airs where no
input is supported properly, for example.
This patch fixes the problem: now "Headphone Mic Jack Mode" is created
when such an input selection isn't possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To reduce driver resume time, this patch resumes the codecs in parallel
if there are multiple codecs on the bus.
- The PM workqueue of bus is also used to parallel resuming multiple codecs.
- The work item 'pm_work' is renamed to 'suspend_work' to parallel suspending
codecs.
- Add a work item 'resume_work' to parallel resuming codecs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The time to suspend a single codec may be several hundreds of ms. When runtime
power saving is disabled, driver suspend time can be long especially when there
are more than one codec on the bus.
To reduce driver suspend time, this patch creates a work queue for the bus, and
suspends the codecs in parallel if there are multiple codecs on the bus.
[fixed cosmetic issues by tiwai]
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most Thinkpad Edge series laptops use conexant codec, so far although
the codecs have different minor Vendor Id and minor Subsystem Id,
they all belong to the cxt5066 family, this change can make the
mute/mic-mute LEDs support more generic among cxt_5066 family.
This design refers to the similar solution for the realtek codec
ALC269 family in the patch_realtek.c.
Cc: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to Mengdong, we shouldn't enable runtime PM when a codec
doesn't support EPSS, based on the experiences on Windows.
We have already this check in HDMI codec drivers, but now apply it in
general in hda_codec.c.
Credit goes to Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we fixed the long-standing bugs of runtime PM, let's enable
Panther Point again. The runtime PM was disabled in the HDMI codec
driver due to the S3 issue, and this should have been fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No functional change.
- codec->pm_down_notified flag is renamed to codec->pm_up_notified
flag (and takes the reversed meaning), which is managed solely in
hda_call_pm_notify() now.
- The explicit call of hda_call_pm_notify() is moved into
hda_keep_power_on().
- Removed a redundant call of hda_call_pm_notify() in
snd_hda_power_up(), as it's called in hda_call_codec_resume()
anyway.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a codec contains only the digital outputs, it's very likely a
HDMI/DP codec, which isn't supported by the generic parser but via
HDMI codec parser code. Detect such a case and bind with the proper
parser object if available.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drop the hard dependency on the generic parser code and load / unload
the generic parser code dynamically if built as a module. This allows
us to avoid the generic parser if only HDMI/DP codecs are found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the missing pcbeep default amp for ALC668.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
current_headset_type should be of the HEADSET_TYPE enum, not the
HEADSET_MODE enum. Since ALC_HEADSET_TYPE_UNKNOWN and ALC_HEADSET_MODE_UNKNOWN
are both 0, this patch is just janitorial.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models (or maybe depending on BIOS version) of Sony VAIO with
ALC260 give no proper pin configurations as default, resulting in the
non-working speaker, etc. Just provide the whole pin configurations
via a fixup.
Reported-by: Matthew Markus <mmarkus@hearit.co>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The laptop has a built-in speaker on NID 0x1a. It's an LFE only on
the right channel, so we need to provide an explicit chmap, too.
There might be other surround speakers, but they can fixed in addition
at later point, so let's fix the easier bass speaker at first.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65091
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec is resumed, it keeps the power on while the resuming
phase via hda_keep_power_on(), then turns down via
snd_hda_power_down(). At that point, snd_hda_power_down() notifies
the power down to the controller, and this may confuse the refcount if
the codec was already powered up before the resume.
In the end result, the controller goes to runtime suspend even before
the codec is kicked off to the power save, and the communication
stalls happens.
The fix is to add the power-up notification together with
hda_keep_power_on(), and clears the flag appropriately.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!
BugLink: https://bugs.launchpad.net/bugs/1253038
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and load from the external firmware files.
The firmware binary blobs in cs46xx driver have been in a gray zone
regarding the license. It's most likely should be OK, but still
unclear. And, the size isn't that small, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=10750
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station is a Thinkpad thing, so it makes sense to check
for mute/micmute LEDs for that quirk type too.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're using the ACPI interface to detect whether we're dealing with a Thinkpad
or not. This way we're not loading the thinkpad_acpi module when we're not on
a Thinkpad, but at the same time, we give the opportunity to check for, and
potentially enable, both present and future Thinkpad with mute/micmute LEDs.
At least those running the ALC269 family (269 to 299) of Realtek codecs.
Cc: Alex Hung <alex.hung@canonical.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_reset() is called either in resetting the whole setup at
error paths or hwdep clear/reconfig sysfs triggers. But all of these
don't assume that the power has to be off, rather they want to keep
the power state unchanged (e.g. reconfig_codec() calls the power
up/down by itself). Thus, unconditionally clearing the power state in
snd_hda_codec_reset() leads to the inconsistency, confuses the further
operation. This patch gets rid of the lines doing that bad thing.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly as other laptops with AD1981 & co codecs, we can control
EAPD on AD1986A more safely depending on the Master switch, in order
to save some power.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only EAPD on AD1986A is on NID 0x1b where usually the speaker.
But this doesn't control only the speaker amp but may influence on all
outputs, e.g. Lenovo N100 laptop seems to have this issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We don't change the EAPD bit in set_pin_eapd() if keep_eapd_on flag is
set by the codec driver and enable is false. But, we also apply the
flipping of enable value according to inv_eapd flag in the same
function, and this confused the former check, handled as if it's
turned ON. The inverted EAPD check must be applied after keep_eapd_on
check, instead.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case there is both a multifunction headset jack and a Line Out
jack, automuting was not working properly from the Line Out jack.
This patch fixes that issue.
Cc: stable@vger.kernel.org (3.10+)
BugLink: https://bugs.launchpad.net/bugs/1250377
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA specification the baseline ELD length is counted in
DW of 4 bytes instead of in bytes.
Fix the code accordingly.
Baseline length is not used by the kernel so only the ELD exported to
userspace was affected. No issues have been reported.
v2: Fixed so that eld_size is adjusted upwards accordingly as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ATI/AMD video/audio latencies are specified in apparent HDMI VSDB
format. In this format values above 251 are not valid (or stream
component is not supported - 255), but no checking is performed since
this was not mentioned in the AMD HDA verbs specification.
Check that the latencies are valid before using them, and add a comment
describing the formats.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add error checks to HBR status reads (both generic and ATI/AMD) and
ATI/AMD codec reads for ELD generation.
Unchecked errors in these just caused more errors later on (invalid
codec writes for the HBR ones and ELD parsing errors for the ATI/AMD ELD
ones), but it is better to catch them earlier.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).
Since the USB audio code has used the TFx positions since v3.8
(04324ccc75, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510b2 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SPDIF output MBP11,2 requires the pin control to be set/cleared
for turning on/off the optical SPDIF. The red light turns off only
when the corresponding pin control is cleared (or powered to D3).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [8fe7b65ab465: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65ab4 ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dmesg here has a 100+ consecutive lines of:
[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...
Ratelimit the message to reduce the dmesg log noise.
Coalesce the format while at it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added a missing ifdef:
sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dylan Reid