We need to return the corresponding bit for a particular GPIO. This bit
contains shift not mask.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the hp mic pin has no VREF bits, the driver forgot to set PIN_IN
bit. Spotted during debugging old MacBook Airs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a headphone jack is configurable as input, the generic parser
tries to make it retaskable as Headphone Mic. The switching can be
done smoothly if Capture Source control exists (i.e. there is another
input source). Or when user explicitly enables the creation of jack
mode controls, "Headhpone Mic Jack Mode" will be created accordingly.
However, if the headphone mic is the only input source, we have to
create "Headphone Mic Jack Mode" control because there is no capture
source selection. Otherwise, the generic parser assumes that the
input is constantly enabled, thus the headphone is permanently set
as input. This situation happens on the old MacBook Airs where no
input is supported properly, for example.
This patch fixes the problem: now "Headphone Mic Jack Mode" is created
when such an input selection isn't possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PL061 driver had the irqdomain initialization in an unfortunate
place: when used with device tree (and thus passing the base IRQ
0) the driver would work, as this registers an irqdomain and waits
for mappings to be done dynamically as the devices request their
IRQs, whereas when booting using platform data the irqdomain core
would attempt to allocate IRQ descriptors dynamically (which works
fine) but also to associate the irq_domain_associate_many() on all
IRQs, which in turn will call the mapping function which at this
point will try to set the type of the IRQ and then tries to acquire
a non-initialized spinlock yielding a backtrace like this:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc1+ #652
Backtrace:
[<c0016f0c>] (dump_backtrace) from [<c00172ac>] (show_stack+0x18/0x1c)
r6:c798ace0 r5:00000000 r4:c78257e0 r3:00200140
[<c0017294>] (show_stack) from [<c0329ea0>] (dump_stack+0x20/0x28)
[<c0329e80>] (dump_stack) from [<c004fa80>] (__lock_acquire+0x1c0/0x1b80)
[<c004f8c0>] (__lock_acquire) from [<c0051970>] (lock_acquire+0x6c/0x80)
r10:00000000 r9:c0455234 r8:00000060 r7:c047d798 r6:600000d3 r5:00000000
r4:c782c000
[<c0051904>] (lock_acquire) from [<c032e484>] (_raw_spin_lock_irqsave+0x60/0x74)
r6:c01a1100 r5:800000d3 r4:c798acd0
[<c032e424>] (_raw_spin_lock_irqsave) from [<c01a1100>] (pl061_irq_type+0x28/0x)
r6:00000000 r5:00000000 r4:c798acd0
[<c01a10d8>] (pl061_irq_type) from [<c0059ef4>] (__irq_set_trigger+0x70/0x104)
r6:00000000 r5:c01a10d8 r4:c046da1c r3:c01a10d8
[<c0059e84>] (__irq_set_trigger) from [<c005b348>] (irq_set_irq_type+0x40/0x60)
r10:c043240c r8:00000060 r7:00000000 r6:c046da1c r5:00000060 r4:00000000
[<c005b308>] (irq_set_irq_type) from [<c01a1208>] (pl061_irq_map+0x40/0x54)
r6:c79693c0 r5:c798acd0 r4:00000060
[<c01a11c8>] (pl061_irq_map) from [<c005d27c>] (irq_domain_associate+0xc0/0x190)
r5:00000060 r4:c046da1c
[<c005d1bc>] (irq_domain_associate) from [<c005d604>] (irq_domain_associate_man)
r8:00000008 r7:00000000 r6:c79693c0 r5:00000060 r4:00000000
[<c005d5d0>] (irq_domain_associate_many) from [<c005d864>] (irq_domain_add_simp)
r8:c046578c r7:c035b72c r6:c79693c0 r5:00000060 r4:00000008 r3:00000008
[<c005d814>] (irq_domain_add_simple) from [<c01a1380>] (pl061_probe+0xc4/0x22c)
r6:00000060 r5:c0464380 r4:c798acd0
[<c01a12bc>] (pl061_probe) from [<c01c0450>] (amba_probe+0x74/0xe0)
r10:c043240c r9:c0455234 r8:00000000 r7:c047d7f8 r6:c047d744 r5:00000000
r4:c0464380
This moves the irqdomain initialization to a point where the spinlock
and GPIO chip are both fully propulated, so the callbacks can be used
without crashes.
I had some problem reproducing the crash, as the devm_kzalloc():ed
zeroed memory would seemingly mask the spinlock as something OK,
but by poisoning the lock like this:
u32 *dum;
dum = (u32 *) &chip->lock;
*dum = 0xaaaaaaaaU;
I could reproduce, fix and test the patch.
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For Wireless USB audio devices, use multiple isoc packets per URB for
inbound endpoints with a datainterval < 5. This allows the WUSB host
controller to take advantage of bursting to service endpoints whose
logical polling interval is less than the 4ms minimum polling interval
limit in WUSB.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UHID allows short writes so user-space can omit unused fields. We
automatically set them to 0 in the kernel. However, the 64/32 bit
compat-handler didn't do that in the UHID_CREATE fallback. This will
reveal random kernel heap data (of random size, even) to user-space.
Fixes: befde0226a ('HID: uhid: make creating devices work on 64/32 systems')
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most Thinkpad Edge series laptops use conexant codec, so far although
the codecs have different minor Vendor Id and minor Subsystem Id,
they all belong to the cxt5066 family, this change can make the
mute/mic-mute LEDs support more generic among cxt_5066 family.
This design refers to the similar solution for the realtek codec
ALC269 family in the patch_realtek.c.
Cc: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1) is a bug fix that happens when root does the following:
echo function_graph > current_tracer
modprobe foo
echo nop > current_tracer
This causes the ftrace internal accounting to get screwed up and
crashes ftrace, preventing the user from using the function tracer
after that.
2) if a TRACE_EVENT has a string field, and NULL is given for it.
The internal trace event code does a strlen() and strcpy() on the
source of field. If it is NULL it causes the system to oops.
This bug has been there since 2.6.31, but no TRACE_EVENT ever passed
in a NULL to the string field, until now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSlUw+AAoJEKQekfcNnQGugTYIAJQ7Zfhor2Jrw7XzkcBDpQv9
kqL/NvjLfyA49BLwba0VJCqJA56dEfW7kaSa7Wx0qAHdHKATLDA8G4c9FdHRAmZf
WJ4jDbrcJqc7DA2vEn4aUuczwvTMx0H1KJHPMAu9taEno3YocIzCMxkuNYelwAz2
XUkUGtR7olF85pyVccfZLKnKPtslSwxWoG6WgEqiAap6fIorPlcSXBVYFqLKVTRJ
P2e847eqxMF5ACLmv3dWiEvTPtWY91abN1zpeJYQNjBtQJmzVlvRcXYE6TwPUIFg
RtB9n3SrT+0lEWvcxDbQi+4hKHf+JQLkGaYwWCMJihbdF4sh36olzpUOimKVqsk=
=+9+v
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This includes two fixes.
1) is a bug fix that happens when root does the following:
echo function_graph > current_tracer
modprobe foo
echo nop > current_tracer
This causes the ftrace internal accounting to get screwed up and
crashes ftrace, preventing the user from using the function tracer
after that.
2) if a TRACE_EVENT has a string field, and NULL is given for it.
The internal trace event code does a strlen() and strcpy() on the
source of field. If it is NULL it causes the system to oops.
This bug has been there since 2.6.31, but no TRACE_EVENT ever passed
in a NULL to the string field, until now"
* tag 'trace-fixes-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix function graph with loading of modules
tracing: Allow events to have NULL strings
Pull ceph bug-fixes from Sage Weil:
"These include a couple fixes to the new fscache code that went in
during the last cycle (which will need to go stable@ shortly as well),
a couple client-side directory fragmentation fixes, a fix for a race
in the cap release queuing path, and a couple race fixes in the
request abort and resend code.
Obviously some of this could have gone into 3.12 final, but I
preferred to overtest rather than send things in for a late -rc, and
then my travel schedule intervened"
* 'for-linus-bugs' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: allocate non-zero page to fscache in readpage()
ceph: wake up 'safe' waiters when unregistering request
ceph: cleanup aborted requests when re-sending requests.
ceph: handle race between cap reconnect and cap release
ceph: set caps count after composing cap reconnect message
ceph: queue cap release in __ceph_remove_cap()
ceph: handle frag mismatch between readdir request and reply
ceph: remove outdated frag information
ceph: hung on ceph fscache invalidate in some cases
We are missing building windfarm_max6690_sensor.o when building
CONFIG_WINDFARM_RM31. Usually all the windfarm drivers are built
and thus this isn't a problem but some more "tailored" setups
(Gentoo ?) building only that driver are not working because
the require sensor module is missing.
Reported-by: Stanislav Ponomarev <devhexorg@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* acpica:
ACPI: Clean up incorrect inclusions of ACPICA headers
ACPICA: Update version to 20131115.
ACPICA: Add support to delete all objects attached to the root namespace node.
ACPICA: Delete all attached data objects during namespace node deletion.
ACPICA: Resources: Fix loop termination for the get AML length function.
ACPICA: Tests: Add CHECKSUM_ABORT protection for test utilities.
ACPICA: Debug output: Do not emit function nesting level for kernel build.
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Pull IMA fixes from James Morris:
"These three patches fix regressions in the IMA code in your current
tree.
The first fixes a couple of bugs in template_desc_init_fields(), and
the other two ensure that changes in this kernel don't break
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: make a copy of template_fmt in template_desc_init_fields()
ima: do not send field length to userspace for digest of ima template
ima: do not include field length in template digest calc for ima template
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage. Also, clean-ups
to remove duplicate defines and document a hardware errata. Finally,
some changes to improve performance.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nOG2
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.13' of git://github.com/jonmason/ntb
Pull non-transparent bridge updates from Jon Mason:
"NTB driver bug fixes to address a missed call to pci_enable_msix,
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage.
Also, clean-ups to remove duplicate defines and document a hardware
errata. Finally, some changes to improve performance"
* tag 'ntb-3.13' of git://github.com/jonmason/ntb:
NTB: Disable interrupts and poll under high load
NTB: Enable Snoop on Primary Side
NTB: Document HW errata
NTB: remove duplicate defines
NTB: correct dmaengine_get/put usage
NTB: Fix ntb_transport link down race
ntb: Fix missed call to pci_enable_msix()
NTB: Fix NTB-RP Link Up
NTB: Xeon Doorbell errata workaround
Commit 8c4f3c3fa9 "ftrace: Check module functions being traced on reload"
fixed module loading and unloading with respect to function tracing, but
it missed the function graph tracer. If you perform the following
# cd /sys/kernel/debug/tracing
# echo function_graph > current_tracer
# modprobe nfsd
# echo nop > current_tracer
You'll get the following oops message:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 2910 at /linux.git/kernel/trace/ftrace.c:1640 __ftrace_hash_rec_update.part.35+0x168/0x1b9()
Modules linked in: nfsd exportfs nfs_acl lockd ipt_MASQUERADE sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables uinput snd_hda_codec_idt
CPU: 2 PID: 2910 Comm: bash Not tainted 3.13.0-rc1-test #7
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
0000000000000668 ffff8800787efcf8 ffffffff814fe193 ffff88007d500000
0000000000000000 ffff8800787efd38 ffffffff8103b80a 0000000000000668
ffffffff810b2b9a ffffffff81a48370 0000000000000001 ffff880037aea000
Call Trace:
[<ffffffff814fe193>] dump_stack+0x4f/0x7c
[<ffffffff8103b80a>] warn_slowpath_common+0x81/0x9b
[<ffffffff810b2b9a>] ? __ftrace_hash_rec_update.part.35+0x168/0x1b9
[<ffffffff8103b83e>] warn_slowpath_null+0x1a/0x1c
[<ffffffff810b2b9a>] __ftrace_hash_rec_update.part.35+0x168/0x1b9
[<ffffffff81502f89>] ? __mutex_lock_slowpath+0x364/0x364
[<ffffffff810b2cc2>] ftrace_shutdown+0xd7/0x12b
[<ffffffff810b47f0>] unregister_ftrace_graph+0x49/0x78
[<ffffffff810c4b30>] graph_trace_reset+0xe/0x10
[<ffffffff810bf393>] tracing_set_tracer+0xa7/0x26a
[<ffffffff810bf5e1>] tracing_set_trace_write+0x8b/0xbd
[<ffffffff810c501c>] ? ftrace_return_to_handler+0xb2/0xde
[<ffffffff811240a8>] ? __sb_end_write+0x5e/0x5e
[<ffffffff81122aed>] vfs_write+0xab/0xf6
[<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85
[<ffffffff81122dbd>] SyS_write+0x59/0x82
[<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85
[<ffffffff8150a2d2>] system_call_fastpath+0x16/0x1b
---[ end trace 940358030751eafb ]---
The above mentioned commit didn't go far enough. Well, it covered the
function tracer by adding checks in __register_ftrace_function(). The
problem is that the function graph tracer circumvents that (for a slight
efficiency gain when function graph trace is running with a function
tracer. The gain was not worth this).
The problem came with ftrace_startup() which should always be called after
__register_ftrace_function(), if you want this bug to be completely fixed.
Anyway, this solution moves __register_ftrace_function() inside of
ftrace_startup() and removes the need to call them both.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Fixes: ed926f9b35 ("ftrace: Use counters to enable functions to trace")
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Correct a typo that prevented the driver from being built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the missing pcbeep default amp for ALC668.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Follow-up to commit 294d31e822 ("sony-laptop: don't change keyboard
backlight settings"): avoid messing up the state on resume. Leave it to
what was before suspending as it's anyway likely that we still don't
know what value we should write to the EC registers. This fix is also
required in 3.12
Cc: stable@vger.kernel.org
Tested-by: Karol Babioch <karol@babioch.de>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c284ee2cf1. Turns out
the locking was incorrect.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Header file <acpi/acpi.h> contains environemnt settings and architecture
specific implementation that should be included before any other ACPICA
headers in order to keep a consistent build environment for ACPICA users.
The following internal ACPICA header files should be included from
<acpi/acpi.h> and should not be included by other kernel files:
<acpi/acpiosxf.h>
<acpi/acpixf.h>
Clean up incorrect inclusions of these files from non-ACPICA source
files.
[rjw: Subject and changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d64675 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
idlestates in sysfs are counted from 0.
This fixes a wrong error message.
Current behavior on a machine with 4 sleep states is:
cpupower idle-set -e 4
Idlestate 4 enabled on CPU 0
-----Wrong---------------------
cpupower idle-set -e 5
Idlestate enabling not supported by kernel
-----Must and now will be -----
cpupower idle-set -e 5
Idlestate 6 not available on CPU 0
-------------------------------
cpupower idle-set -e 6
Idlestate 6 not available on CPU 0
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpupower idle-set subcommand was introduce recently.
This patch provides the missing manpage.
If cpupower is properly installed it will show up automatically
(similar to git), when invoking:
cpupower help idle-set
or
cpupower idle-set --help
Some parts have been taken over and adjusted from
git commit 62d6ae880e
documentation submitted by Carsten Emde.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
zsmalloc encodes a handle using the pfn and an object
index. On hardware platforms with physical memory starting
at 0x0 the pfn can be 0. This causes the encoded handle to be
0 and is incorrectly interpreted as an allocation failure.
This issue affects all current and future SoCs with physical
memory starting at 0x0. All MSM8974 SoCs which includes
Google Nexus 5 devices are affected.
To prevent this false error we ensure that the encoded handle
will not be 0 when allocation succeeds.
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was introduced due to a patch hunk when porting
commit 20802057 (staging/lustre/ptlrpc: race in pinger).
Cc: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=cIMc
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 3.13 cycle.
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
A bunch of fixes, a few driver specific ones and a framework fix for
voltage enumeration on fixed voltage regulators which had previously
worked but had been misplaced during some refactoring causing problems
for users that needed to know the voltage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=2BEl
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of fixes, a few driver specific ones and a framework fix for
voltage enumeration on fixed voltage regulators which had previously
worked but had been misplaced during some refactoring causing problems
for users that needed to know the voltage"
* tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: arizona-micsupp: Correct wm5110 voltage selection
regulator: pfuze100: allow misprogrammed ID
regulator: fixed: fix regulator_list_voltage() for regression
regulator: gpio-regulator: Don't oops on missing regulator-type property
drivers/staging/btmtk_usb/btmtk_usb.c: In function ‘btmtk_usb_probe’:
drivers/staging/btmtk_usb/btmtk_usb.c:1610: warning: assignment from incompatible pointer type
Add the new hdev parameter, cfr. commit
7bd8f09f69 ("Bluetooth: Add hdev parameter to
hdev->send driver callback").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up the remaining "dev is used before it is set" issues in the
go7007 driver that were originally caused by commit
b6ea5ef80a but not fixed up by reverting
it due to other patches later on adding these "fixes".
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dulshani Gunawardhana <dulshani.gunawardhana89@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8d181e408 (staging: drm/imx: add drm plane support) added a file
to the make target for DRM_IMX_IPUV3 but didn't adjust the objs required
to actually build that as a module. Kbuild got confused and this lead to
link errors like:
ERROR: "ipu_plane_disable" [drivers/staging/imx-drm/ipuv3-crtc.ko] undefined!
ERROR: "ipu_plane_enable" [drivers/staging/imx-drm/ipuv3-crtc.ko] undefined!
Additionally, it added a call to imx_drm_crtc_id which also fails with a
link error as above. To fix this, we adjust the make target with the proper
objs, which will change the name of the resulting .ko. We also add an
EXPORT_SYMBOL_GPL for imx_drm_crtc_id.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Fixes: b8d181e408 '(staging: drm/imx: add drm plane support)'
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Markus Mayer