Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver to support older EC firmware that only support deprecated
ec command. Rely on ACPI memory map register to access sensor
information.
Present same interface as the regular cros_ec sensor stack:
- one iio device per accelerometer
- use HTML5 axis definition
- use iio abi units
- accept calibration calls, but do nothing
Chrome can use the same code than regular cros_ec sensor stack to
calculate orientation and lid angle.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS3DHH accel sensor
http://www.st.com/resource/en/datasheet/lis3dhh.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order
to contain irq line parameters of the device.
Moreover separate data-ready open-drain configuration parameters for INT1
and INT2 pins in st_sensor_data_ready_irq data structure.
That change will be used to properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2DW12 accelerometer in
st_accel framework
http://www.st.com/resource/en/datasheet/lis2dw12.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
KXTF9 has mostly compatible register layout to KXCJK accelerometer.
There is no motion direction interrupt support, but there is tap
direction detection instead (not implemented in this patch).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make sampling_frequency_avail per-type - like sampling_frequency is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation for KXTF9 support, make sampling_frequency_avail
attribute dynamic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract reporting of motion event direction from interrupt handler,
as it is not supported by KXTF9.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix INT_CTRL1 bit names to match register name and add names
for INT_SRC1 bits.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor ODR/WUF setting code in preparation of KXTF9 support.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'mma8452_read_thresh' and 'mma8452_write_thresh' functions
does more than just read/write threshold values.
They also handle IIO_EV_INFO_HIGH_PASS_FILTER_3DB and
IIO_EV_INFO_PERIOD therefore renaming to generic names.
Improves code readability, no impact on functionality.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace 'unsigned' with 'unsigned int'
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace symbolic permissions with octal permissions
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports multiple devices like mma8653,
mma8652, mma8452, mma8453 and fxls8471. Almost all
these devices have more than one event.
Current driver design hardcodes the event specific
information, so only one event can be supported by this
driver at any given time.
Also current design doesn't have the flexibility to
add more events.
This patch improves by detaching the event related
information from chip_info struct,and based on channel
type and event direction the corresponding event
configuration registers are picked dynamically.
Hence both transient and freefall events can be
handled in read/write callbacks.
Changes are thoroughly tested on fxls8471 device on imx6UL
Eval board using iio_event_monitor user space program.
After this fix both Freefall and Transient events are
handled by the driver without any conflicts.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove int2 configuration parameter for LIS3DH, LSM303DLHC, LSM330D,
LSM330DL, LSM330DLC, LSM303AGR, LIS2DH12 and LNG2DM since these devices
export just int1 as data-ready line
Fixes: 23cde4d65c (iio: Added platform data to select the DRDY pin)
Fixes: dcdb0a78ca (iio: accel: st_accel: add support to lng2dm)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to use the standard name convention rename H3LIS331DL_DRIVER_NAME
macro in H3LIS331DL_ACCEL_DEV_NAME
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add H3LIS331DL, LIS331DL and LIS3LV02DL entries in st_accel_id_table
Fixes: 1e52fefc9b (iio: accel: Add support for the h3lis331dl accel)
Fixes: bbf5f037fa (iio: st_accel: support the LIS331DL sensor)
Fixes: 3acddf74f8 (iio: st-sensors: add support for lis3lv02d accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array init_data static rather having it on the
stack saves us a couple hundreds of bytes:
Before:
text data bss dec hex filename
3175 848 0 4023 fb7 drivers/iio/accel/da311.o
After:
text data bss dec hex filename
2860 936 0 3796 ed4 drivers/iio/accel/da311.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the BOSC0200 ACPI device id used on some x86 tablets.
note driver_data is not set to a specific model, driver_data is not
used anyways (instead detection is done on the chip_id reg) and the
2 tablets with a BOSC0200 ACPI device id I've have 2 different chips,
one has a BMA250E, the other a BMA222E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While using GPIO library API we might get into troubles in the future,
because we can't rely on label name in the driver since vendor firmware
might provide any GPIO pin there, e.g. "reset", and even mark it in _DSD
(in which case the request will fail).
To avoid inconsistency and potential issues we have two options:
a) generate GPIO ACPI mapping table and supply it via
acpi_dev_add_driver_gpios(), or
b) just pass NULL as connection ID.
The b) approach is much simpler and would work since the driver relies
on GPIO indices only. Moreover, the _CRS fallback mechanism, when
requesting GPIO, is going to be stricter, and supplying non-NULL
connection ID when neither _DSD, nor GPIO ACPI mapping is present, will
make request fail.
See
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git/commit/?h=for-next&id=ed7fcf1ed5ea4ea01243995ae085757a77cf0f3e for more background.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit f1320b0951.
The BMA250E is already handled by the bmc150-accel-i2c driver, which
supports the "E" variants of the BMA??? accelerometers better then the
bma180 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit 5333e88661.
The BMA250E is already handled by the bmc150-accel-i2c driver, which
supports the "E" variants of the BMA??? accelerometers better then the
bma180 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove LSM303DL, LSM303DLM, LSM303DLH, LSM303DLHC from st_accel_id_table
since LSM303DL series does not support spi interface
Fixes: d62511689d (iio: accel: Add STMicroelectronics accel driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some x86 tablets use the BMA250E accelerometer, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The BMA250E adds a new fifo mode and is fully backwards compatible
with the BMA250, but with a different chip-id.
This commit adds support for it by adjusting the chip-id check and
otherwise treating it as a regular BMA250.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drop static on a local variable, when the variable is initialized before
use, on every possible execution path through the function. The static has
no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
3879 512 8 4399 112f drivers/iio/accel/hid-sensor-accel-3d.o
after:
text data bss dec hex filename
3863 512 0 4375 1117 drivers/iio/accel/hid-sensor-accel-3d.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.
1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure
2. Re-load the driver
$ sudo insmod st_pressure
$ sudo insmod st_pressure_i2c
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When both accel_3d and gravity sensor are present, iio_device_register()
fails with "Duplicate scan index" error.
The reason for this is setting of indio_dev->num_channels based on
accel_3d channel for both gravity and accel-3d sensor. But number of
channels are not same, so for gravity it is pointing to some invalid
memory and getting scan_index to compare which may match.
To fix this issue, set the indio_dev->num_channels correctly based on
the sensor type.
Fixes: 0e377f3b9a ('iio: Add gravity sensor support')
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add SPI driver that initializes SPI regmap for the adxl345 core driver.
The driver supports the same functionality as I2C namely the x, y, z and
scale readings.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Linus Torvalds