The CSI controller can take raw data from the data bus and output RGB565
format. The controller does not distinguish between RGB565 LE and BE.
Instead this is determined by the media bus format, i.e. the format or
order the sensor is sending data in.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
max_register is currently set to 0x1000. This is beyond the mapped
address range of the hardware, so attempts to dump the regmap from
debugfs would trigger a kernel exception.
Furthermore, the useful registers only occupy a small section at the
beginning of the full range. Change the value to 0x9c, the last known
register on the V3s and H3.
On the A31, the register range is extended to support additional
capture channels. Since this is not yet supported, ignore it for now.
Fixes: 5cc7522d89 ("media: sun6i: Add support for Allwinner CSI V3s")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CSI block in Allwinner A64 has similar features as like in H3,
but the default CSI_SCLK rate cannot work properly to drive the
connected sensor interface.
The tested mod cock rate is 300 MHz and BSP vfe media driver is also
using the same rate. Unfortunately there is no valid information about
clock rate in manual or any other sources except the BSP driver. so more
faith on BSP code, because same has tested in mainline.
So, add support for A64 CSI block by setting updated mod clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Add a compatible string entry for the H3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are spelling mistakes in dev_dbg messages, fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The first device that used that IP was the A31. Add it to our list of
compatibles.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are a few other coding style issues reported by checkpatch
while in --strict mode. Fix the ones that make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make checkpatch.pl happier by running it on strict mode and
using the --fix-inline to solve some issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allwinner V3s SoC features a CSI module with parallel interface.
This patch implement a v4l2 framework driver for it.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Chen-Yu Tsai