tps6586 does not support burst writes. i2c writes have to be
1 byte at a time.
Cc: stable@kernel.org
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ASoC supports keeping the audio subsysetm active over suspend in order
to support use cases such as audio passthrough from a cellular modem
with the main CPU suspended. Ensure that we don't power down the CODEC
when this is happening by checking to see if VMID is up and skipping
suspend and resume when it is. If the CODEC has suspended then it'll
turn VMID off before the core suspend() gets called.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the device name in DaVinci Voice Codec MFD driver to load
davinci-vcif and cq93vc codec client drivers.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for chip version 2.0 or cut 2.0.
One new interrupt latch register - latch 12 - is introduced.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x can generate wake events, some unconditionally, so flag
the primary IRQ as a wake source in order to help the CPU treat the
/IRQ signal appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the legacy bus PM operations are deprecated move the suspend
method over to dev_pm_ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the driver to save and restore register values
for hibernation.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the Ab8500 v1.0, the SPI support is deprecated on the HW.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While it is vanishingly unlikely that the device will be deployed on other
architectures removing the dependency facilitates build testing when doing
generic work on both the MFD core for the device and the subsystem drivers.
There appears to be no actual code dependency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Actually makes the code larger rathe rthan smaller but does provide some
isolation against core API changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to irq_chip
operations. Update the TWL4030 driver to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the tps6586x driver to the
new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being update to pass struct irq_data to irq_chip rather
than an irq number to operations. Update tc6393 to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than an
irq number to irq_chip operations. Update the t7166xb driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the SMTPE driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to interrupt
operations, update the MAX8998 driver to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq infrastructure is being converted to pass struct irq_data rather
than an irq number to irq_chip operations, update max8925 to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the jz4740-adc driver to use the recently introduced IRQ API
variants which are passed struct irq_data rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to supply struct irq_data to chips
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than irq
numbers into chip drivers. As part of the update assignments to NULL for
unused operations are removed, these are not needed and the genirq docs
should be good enough.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interrupt controller APIs are being updated to pass a struct irq_data
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interrupt controller APIs are being updated to pass a struct irq_data
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of these are GPIO operations, though a couple are just internal only
functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Partly for coding style reasons, but mostly because sparse warns on it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We should specify both a start and an end for the IRQ range rather than
initialise the start twice.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There's no use of either of these outside of the driver so they can be
declared static.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
... and convert it to a dev_info print at probe time.
There are many variants of this chip with different values of VERSIONCRC.
The set of values is large, and not useful to enumerate. All are SW
compatible. The difference lies in default settings of the various power
rails, and other similar differences. The driver, or clients of the
driver, shouldn't be affected by this, since all rails should be
programmed into the desired state in all cases for correct operation.
Derived-from-code-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the following section mismatch warning when building
omap2plus_defconfig:
WARNING: vmlinux.o(.data+0x47d7c): Section mismatch in reference
from the variable twl_driver to the function .init.text:twl_probe()
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the ioresources used by subdrivers to
retrieve their interrupt.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the system wake up from suspend when an
ab8500 interrupt occur. This can for example be USB cable
insert or an RTC alarm.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a file into sysfs for reading out chip id.
It has been requested for modem silent reboot.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Ludovic Barre <ludovic.barre@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We check for dev before dereferencing it.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ARRAY_SIZE() returns size_t; use %zu instead of %d so that we don't
get warnings on x86-64.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the WM8994 to completely power off, including disabling the LDOs
if they are software controlled, when it goes idle. The CODEC subdevice
controls activity for the MFD as a whole.
If the GPIOs need to be used while the device is active runtime PM
should be disabled for the device by machine specific code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow MFD cells to have pm_runtime_no_callbacks() called on them during
registration. This causes the runtime PM framework to ignore them,
allowing use of runtime PM to suspend the device as a whole even if
not all drivers for the MFD can usefully implement runtime PM. For
example, RTCs are likely to run continuously regardless of the power
state of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8326 is a high performance variant of the WM832x series with
no software visible differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All the current WM832x devices have the same set of subdevices so can
just use multiple case statements with a single body.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
vwadekar@nvidia.com