Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
IOSF_MBI is tristate. Baytrail driver isn't.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.
The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 9439eb3ab9 ("asm-generic: io: implement relaxed
accessor macros as conditional wrappers") has added
{read,write}{b,w,l,q}_relaxed to include/asm-generic/io.h.
So COMPILE_TEST can be added.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.
I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IOSF_MBI depends on PCI, so we should not select it but depend on it.
This ensures also we compile on X86 only, other archs will break because
of an arch specific include. Also depend on ACPI since this driver uses
it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: David E. Box <david.e.box@linux.intel.com>
This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.
On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
If NO_DMA=y:
drivers/built-in.o: In function `sh_mobile_i2c_dma_unmap':
i2c-sh_mobile.c:(.text+0x60de42): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_mobile_i2c_xfer_dma':
i2c-sh_mobile.c:(.text+0x60df22): undefined reference to `dma_map_single'
i2c-sh_mobile.c:(.text+0x60df2e): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we are using the clk notifier framework we get compile errors
without COMMON_CLK. But the driver fails to probe without COMMON_CLK
anyways, so just add that as a Kconfig dependency.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC. Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for AMD version of the DW I2C host controller. The device is
enumerated from ACPI namespace with ACPI ID AMD0010. Because the core
driver needs an input source clock, and this is not an Intel LPSS device
where clocks are provided through drivers/acpi/acpi_lpss.c, we register the
clock ourselves if the clock rate is given in ->driver_data
Signed-off-by: Carl Peng <carlpeng008@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers
This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix spelling typos found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simon Horman