There are two asrc module in imx8qm & imx8qxp, each module has
different clock configuration, and the DMA type is EDMA.
So in this patch, we define the new clocks, refine the clock map,
and include struct fsl_asrc_soc_data for different soc usage.
The EDMA channel is fixed with each dma request, one dma request
corresponding to one dma channel. So we need to request dma
channel with dma request of asrc module.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/f33dfe3157b5ab200e09ccbf9ab73d31fac6664b.1575452454.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The output divider should align with the output sample
rate, if use ideal sample rate, there will be a lot of overload,
which would cause underrun.
The maximum divider of asrc clock is 1024, but there is no
judgement for this limitation in driver, which may cause the divider
setting not correct.
For non-ideal ratio mode, the clock rate should divide the sample
rate with no remainder, and the quotient should be less than 1024.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/23c634e4bf58afce5b3ae67f5f42e8d1cae2639a.1572252307.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is error "aplay: pcm_write:2023: write error: Input/output error"
on i.MX8QM/i.MX8QXP platform for S24_3LE format.
In i.MX8QM/i.MX8QXP, the DMA is EDMA, which don't support 24bit
sample, but we didn't add any constraint, that cause issues.
So we need to query the caps of dma, then update the hw parameters
according to the caps.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/b6a4de2bbf960ef291ee902afe4388bd0fc1d347.1569493933.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASRC support 24bit/16bit/8bit input width, which is
data width, not slot width.
For the S20_3LE format, the data with is 20bit, slot width
is 24bit, if we set ASRMCR1n.IWD to be 24bits, the result
is the volume is lower than expected, it likes 24bit data
right shift 4 bits
So replace S20_3LE with S24_3LE in supported list and add S8
format in TX supported list
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/45a7c383f43cc1dd9d0934846447aee653278c03.1569493933.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_format_t is more formal than enum asrc_word_width, which has
two property, width and physical width, which is more accurate than
enum asrc_word_width. So it is better to use in(out)put_format
instead of in(out)put_word_width.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/7937c1404ee327ce141cb03b3575b02ea01a740c.1569493933.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Unify the supported input and output rate, add the
12kHz/24kHz/128kHz to the support list
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we want to support more sample rate, for example 12kHz/24kHz
we need update the process_option table, if we want to support more
sample rate next time, the table need to be updated again. which
is not flexible.
We got a function fsl_asrc_sel_proc to replace the table, which can
give the pre-processing and post-processing options according to
the sample rate.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the output sample rate is [8kHz, 30kHz], the limitation
of the supported ratio range is [1/24, 8]. In the driver
we use (8kHz, 30kHz) instead of [8kHz, 30kHz].
So this patch is to fix this issue and the potential rounding
issue with divider.
Fixes: fff6e03c7b ("ASoC: fsl_asrc: add support for 8-30kHz
output sample rate")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a constraint for the channel number setting on the
asrc of older version (e.g. imx35), the channel number should
be even, odd number isn't valid.
So add this constraint when the asrc of older version is used.
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Same as commit ce492b3b8f
Subject: drm/fsl-dcu: use flat regmap cache
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2871 lockdep_trace_alloc+0x104/0x128
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the driver uses MMIO, the regmap bus of type regmap_mmio
is being used which has fast_io set to true.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'np' variable is already assigned to 'pdev->dev.of_node', so use
it to improve readability.
No functional change.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to announce that the driver has been successfully
probed, so remove the unneeded message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of returning -EINVAL on error, return the real error code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register ASRCFG is volatile, but some bits need to be recovered
after suspend/resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 8kHz, 11.025kHz, 16kHz, 22.05kHz output sample rate support.
According referance menual, "Limited support for the case when
output sampling rates is between 8kHz and 30kHz. The limitation
is the supported ratio (Fsin/Fsout) range as between 1/24 to 8."
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASRC need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ASRC registers
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using params_width function to simplify code.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'name' array is currently stored inside the fsl_asrc private structure only
for registering the interrupt name.
This can be simplified by registering it with dev_name() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Kernel dump (WARN_ON) ocurred during system boot-up inside regmap_write():
------------[ cut here ]------------
WARNING: CPU: 0 PID: 47 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xe8/0x108()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 47 Comm: kworker/u2:2 Not tainted 3.18.0-rc1-10245-gb75d289-dirty #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<80012294>] (dump_backtrace) from [<80012578>] (show_stack+0x18/0x1c)
r6:8097c73c r5:8097c73c r4:00000000 r3:be33ba80
[<80012560>] (show_stack) from [<806aac48>] (dump_stack+0x8c/0xa4)
[<806aabbc>] (dump_stack) from [<8002a694>] (warn_slowpath_common+0x70/0x94)
r6:80062838 r5:00000009 r4:bd827b30 r3:be33ba80
[<8002a624>] (warn_slowpath_common) from [<8002a6f0>] (warn_slowpath_fmt+0x38/0x40)
r8:00000004 r7:00000001 r6:000080d0 r5:60000193 r4:bd826010
[<8002a6bc>] (warn_slowpath_fmt) from [<80062838>] (lockdep_trace_alloc+0xe8/0x108)
r3:80831590 r2:8082e160
[<80062750>] (lockdep_trace_alloc) from [<800ea5dc>] (kmem_cache_alloc+0x28/0x134)
r5:000080d0 r4:be001f00
[<800ea5b4>] (kmem_cache_alloc) from [<8038d72c>] (regcache_rbtree_write+0x15c/0x648)
r10:00000000 r9:0000001c r8:00000004 r7:00000001 r6:00000000 r5:bd819a00
r4:00000000 r3:811aea88
[<8038d5d0>] (regcache_rbtree_write) from [<8038c4d8>] (regcache_write+0x5c/0x64)
r10:be3f9f88 r9:00000000 r8:00000004 r7:00000001 r6:00000000 r5:00000001
r4:bd819a00
[<8038c47c>] (regcache_write) from [<8038b0dc>] (_regmap_raw_write+0x134/0x5f4)
r6:be3f9f84 r5:00000001 r4:bd819a00 r3:00000001
[<8038afa8>] (_regmap_raw_write) from [<8038b610>] (_regmap_bus_raw_write+0x74/0x94)
r10:00000000 r9:00000001 r8:be3fb080 r7:bd819a00 r6:00000001 r5:00000000
r4:bd819a00
[<8038b59c>] (_regmap_bus_raw_write) from [<8038a8b4>] (_regmap_write+0x60/0x9c)
r6:00000001 r5:00000000 r4:bd819a00 r3:8038b59c
[<8038a854>] (_regmap_write) from [<8038ba24>] (regmap_write+0x48/0x68)
r7:bd81ad80 r6:00000001 r5:00000000 r4:bd819a00
[<8038b9dc>] (regmap_write) from [<80528f30>] (fsl_asrc_dai_probe+0x34/0x104)
r6:bd888628 r5:be3fb080 r4:be3b4410 r3:be3b442c
------------[ dump end ]------------
=============================================================================
2741 /*
2742 * Oi! Can't be having __GFP_FS allocations with IRQs disabled.
2743 */
2744 if (DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags)))
2745 return;
=============================================================================
By looking at 2744 line, we can get that it's because regcache_rbtree_write()
would call kmalloc() with GFP flag if it couldn't find an existing block to
insert nodes while this kmalloc() call is inside a spin_lock_irq_save pair,
i.e. IRQs disabled.
Even though this may be a bug that should be fixed, I still try to send this
patch as a quick fix (work around) since it does no harm to assign default
values of every registers when using regcache.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use strncpy() instead of strcpy(). That's not a security issue, as the
source buffer is taken from DT nodes, but we should still enforce bound
checks. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a cut and paste bug so it returns success instead of the error
code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following build errors that were observed by building with
make ARCH=microblaze allyesconfig:
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
^
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a
signal associated with an input clock into a signal associated with a different
output clock. The driver currently works as a Front End of DPCM with other Back
Ends DAI links such as ESAI<->CS42888 and SSI<->WM8962 and SAI. It converts the
original sample rate to a common rate supported by Back Ends for playback while
converts the common rate of Back Ends to a desired rate for capture. It has 3
pairs to support three different substreams within totally 10 channels.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Shengjiu Wang