During HW initialization, driver would set various registers to their
needed values - but it assumes all registers start at their reset-value,
so there's no need to re-configure a register's default value.
This assumption might be incorrect, e.g., in case of preboot driver
running and initializing the driver prior to our driver.
To overcome this, we now ask management firmware to initiate a PF-flr
early during the initialization sequence. That would return everything
in the PF's scope back to default and prevent previous configurations
from still being applied.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.
But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
a. Preboot drivers in some environment can't properly unload.
b. Unexpected driver replacement [kdump, PDA].
Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.
Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.
Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.
This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver interaction with management firmware involves a union
of all the data-members relating to the commands the driver prepares.
Current interface assumes the caller always passes such a union -
but thats cumbersome as well as risky [chancing a stack corruption
in case caller accidentally passes a smaller member instead of union].
Change implementation so that caller could pass a pointer to any
of the members instead of the union.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interaction of driver -> management firmware is based
on a one-pending mailbox [per interface], and various
mailbox commands need to be synchronized.
Current scheme is messy, and there's a difficulty extending
it as it deals differently with various commands as well as
making assumption on the required behavior for load/unload
requests.
Drop the current scheme into a completion-list-based approach;
Each flow would try sending the command when possible,
allowing one flow to complete another flow's completion and
relieve the mailbox before sending its own command.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.
This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.
Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each interfaces assumes it receives an equal portion
of HW/FW resources, but this is wasteful - different partitions
[and specifically, parititions exposing different protocol support]
might require different resources.
Implement a new resource learning scheme where the information is
received directly from the management firmware [which has knowledge
of all of the functions and can serve as arbiter].
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is interested in various tidbits about
the driver - including the driver state & several configuration
related fields [MTU, primtary MAC, etc.].
This adds the necessray logic to update MFW with such configurations,
some of which are passed directly via qed while for others APIs
are provide so that qede would be able to later configure if needed.
This also introduces a new default configuration for MTU which would
replace the default inherited by being an ethernet device.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The New QED firmware contains several fixes, including:
- Wrong classification of packets in 4-port devices.
- Anti-spoof interoperability with encapsulated packets.
- Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.
In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality and APIs needed for selftests.
It adds the ability to configure the link-mode which is required for the
implementation of loopback tests. It adds the APIs for clock test,
register test, interrupt test and memory test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF minimum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF maximum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver interaction with the managemnt firmware is done via mailbox
commands which the management firmware periodically sample, as well
as placing of additional data in set places in the shared memory.
Each PF has a single designated mailbox address, and all flows that
require messaging to the management should use it.
This patch does 2 things:
1. It re-defines the critical section surrounding the mailbox sending -
that section should include the setting of the shared memory as well as
the sending of the command [otherwise a race might send a command with
the data of a different command].
2. It moves the locking scheme from using mutices into using spinlocks.
This lays the groundwork for sending MFW commands from non-sleepable
contexts.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval