This ports the tv-out code from the DDX to KMS.
adds a radeon.tv module option, radeon.tv=0 to disable tv
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the command stream checker for the RN50, R100 and R200 cards.
It stops any access to 3D registers on RN50, and does checks
on buffer sizes on the r100/r200 cards. It also fixes some texture
sizing checks on r300.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
agp/intel: support for new chip variant of IGDNG mobile
drm/i915: Unref old_obj on get_fence_reg() error path
drm/i915: increase default latency constant (v2 w/comment)
The new code adds modes in the helper, which makes more sense
I disliked the non-driver code adding modes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the default mode for every output device when there
is no mode for it.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a function that can be used to add the default mode for the output device
without EDID.
It will add the default mode that meets with the requirements of given
hdisplay/vdisplay limit.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we need to add the standard timing mode, we will firstly check whether it
can be found in DMT table by comparing the hdisplay/vdisplay/vfresh_rate.
If it can't be found, then we will use the cvt/gtf to add the required mode.
If it can be found, it will be returned.
At the same time the function of drm_mode_vrefresh is also fixed. It will
return the result of actual refresh_rate plus 0.5.
For example:
When the calculated value is 84.9, then the fresh_rate is 85.
When the calculated value is 70.02, then the fresh_rate is 70.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we add a standard timing mode in UMS, we will first check whether it can
be found in default mode table. If it can't be found, then we will use cvt/gtf
to add the standard timing mode.
Add the default mode table so that we can check whether the given mode
can be found in the default mode table as what we have done in UMS mode.
If the status of one output device is connected but there is no EDID, it will
have no correct mode. In such case we can add some default modes for it. Of
course we only add the modes in the default modes list that visible part is not
greater than 1024x768.
The default mode is autogenerated from the DMT spec. And it is copied from
xserver/hw/xfree86/modes/xf86EdidModes.c. But the mode with reduced blank
feature is removed.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some rv350+ register for LTE/GTE discard,
and enables the rv515 two sided stencil register.
It also disables the DEPTHXY_OFFSET register which
can be used to workaround the CS checker.
Moves rs690 to proper place in rs600 and uses correct
table on rs600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
- As ima_counts_put() may be called after the inode has been freed,
verify that the inode is not NULL, before dereferencing it.
- Maintain the IMA file counters in may_open() properly, decrementing
any counter increments on subsequent errors.
Reported-by: Ciprian Docan <docan@eden.rutgers.edu>
Reported-by: J.R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: Eric Paris <eparis@redhat.com
Signed-off-by: James Morris <jmorris@namei.org>
According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.
G45 PRM, Vol 1b, p101:
While the “free space” wrap may allow commands to be wrapped around the
end of the Ring Buffer, the wrap should only occur between commands.
Padding (with NOP) may be required to follow this restriction.
Do as commanded.
[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reported by Michael Guntsche <mike@it-loops.com>
--------------------
Commit
38bddf04bc gianfar: gfar_remove needs to call unregister_netdev()
breaks the build of the gianfar driver because "dev" is undefined in
this function. To quickly test rc9 I changed this to priv->ndev but I do
not know if this is the correct one.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm snapshot: fix on disk chunk size validation
dm exception store: split set_chunk_size
dm snapshot: fix header corruption race on invalidation
dm snapshot: refactor zero_disk_area to use chunk_io
dm log: userspace add luid to distinguish between concurrent log instances
dm raid1: do not allow log_failure variable to unset after being set
dm log: remove incorrect field from userspace table output
dm log: fix userspace status output
dm stripe: expose correct io hints
dm table: add more context to terse warning messages
dm table: fix queue_limit checking device iterator
dm snapshot: implement iterate devices
dm multipath: fix oops when request based io fails when no paths
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix bootup with mcount in some configs.
sparc64: Kill spurious NMI watchdog triggers by increasing limit to 30 seconds.
In ext2_rename(), dir_page is acquired through ext2_dotdot(). It is
then released through ext2_set_link() but only if old_dir != new_dir.
Failing that, the pkmap reference count is never decremented and the
page remains pinned forever. Repeat that a couple times with highmem
pages and all pkmap slots get exhausted, and every further kmap() calls
end up stalling on the pkmap_map_wait queue at which point the whole
system comes to a halt.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: ocfs2_write_begin_nolock() should handle len=0
ocfs2: invalidate dentry if its dentry_lock isn't initialized.
The whole write-room thing is something that is up to the _caller_ to
worry about, not the pty layer itself. The total buffer space will
still be limited by the buffering routines themselves, so there is no
advantage or need in having pty_write() artificially limit the size
somehow.
And what happened was that the caller (the n_tty line discipline, in
this case) may have verified that there is room for 2 bytes to be
written (for NL -> CRNL expansion), and it used to then do those writes
as two single-byte writes. And if the first byte written (CR) then
caused a new tty buffer to be allocated, pty_space() may have returned
zero when trying to write the second byte (LF), and then incorrectly
failed the write - leading to a lost newline character.
This should finally fix
http://bugzilla.kernel.org/show_bug.cgi?id=14015
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When translating CR to CRNL in the n_tty line discipline, we did it as
two tty_put_char() calls. Which works, but is stupid, and has caused
problems before too with bad interactions with the write_room() logic.
The generic USB serial driver had that problem, for example.
Now the pty layer had similar issues after being moved to the generic
tty buffering code (in commit d945cb9cce20ac7143c2de8d88b187f62db99bdc:
"pty: Rework the pty layer to use the normal buffering logic").
So stop doing the silly separate two writes, and do it as a single write
instead. That's what the n_tty layer already does for the space
expansion of tabs (XTABS), and it means that we'll now always have just
a single write for the CRNL to match the single 'tty_write_room()' test,
which hopefully means that the next time somebody screws up buffering,
it won't cause weeks of debugging.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tom Horsley reports that his debugger hangs when it tries to read
/proc/pid_of_tracee/maps, this happens since
"mm_for_maps: take ->cred_guard_mutex to fix the race with exec"
04b836cbf19e885f8366bccb2e4b0474346c02d
commit in 2.6.31.
But the root of the problem lies in the fact that do_execve() path calls
tracehook_report_exec() which can stop if the tracer sets PT_TRACE_EXEC.
The tracee must not sleep in TASK_TRACED holding this mutex. Even if we
remove ->cred_guard_mutex from mm_for_maps() and proc_pid_attr_write(),
another task doing PTRACE_ATTACH should not hang until it is killed or the
tracee resumes.
With this patch do_execve() does not use ->cred_guard_mutex directly and
we do not hold it throughout, instead:
- introduce prepare_bprm_creds() helper, it locks the mutex
and calls prepare_exec_creds() to initialize bprm->cred.
- install_exec_creds() drops the mutex after commit_creds(),
and thus before tracehook_report_exec()->ptrace_stop().
or, if exec fails,
free_bprm() drops this mutex when bprm->cred != NULL which
indicates install_exec_creds() was not called.
Reported-by: Tom Horsley <tom.horsley@att.net>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On low-memory systems, anti-fragmentation gets disabled as fragmentation
cannot be avoided on a sufficiently large boundary to be worthwhile. Once
disabled, there is a period of time when all the pageblocks are marked
MOVABLE and the expectation is that they get marked UNMOVABLE at each call
to __rmqueue_fallback().
However, when MAX_ORDER is large the pageblocks do not change ownership
because the normal criteria are not met. This has the effect of
prematurely breaking up too many large contiguous blocks. This is most
serious on NOMMU systems which depend on high-order allocations to boot.
This patch causes pageblocks to change ownership on every fallback when
anti-fragmentation is disabled. This prevents the large blocks being
prematurely broken up.
This is a fix to commit 49255c619f [page
allocator: move check for disabled anti-fragmentation out of fastpath] and
the problem affects 2.6.31-rc8.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the error handling in do_mmap_pgoff(). If do_mmap_shared_file() or
do_mmap_private() fail, we jump to the error_put_region label at which
point we cann __put_nommu_region() on the region - but we haven't yet
added the region to the tree, and so __put_nommu_region() may BUG
because the region tree is empty or it may corrupt the region tree.
To get around this, we can afford to add the region to the region tree
before calling do_mmap_shared_file() or do_mmap_private() as we keep
nommu_region_sem write-locked, so no-one can race with us by seeing a
transient region.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cancel_delayed_work() has to use del_timer_sync() to guarantee the timer
function is not running after return. But most users doesn't actually
need this, and del_timer_sync() has problems: it is not useable from
interrupt, and it depends on every lock which could be taken from irq.
Introduce __cancel_delayed_work() which calls del_timer() instead.
The immediate reason for this patch is
http://bugzilla.kernel.org/show_bug.cgi?id=13757
but hopefully this helper makes sense anyway.
As for 13757 bug, actually we need requeue_delayed_work(), but its
semantics are not yet clear.
Merge this patch early to resolves cross-tree interdependencies between
input and infiniband.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a target writes invalid status (typically status of a command that
already timed out), firewire-sbp2 attempts to put away an ORB that
doesn't exist. https://bugzilla.redhat.com/show_bug.cgi?id=519772
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In dual-buffer DMA mode, no video frames are ever received from R5C832
by libdc1394. Fallback to packet-per-buffer DMA works reliably.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/13393/focus=13476
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Dave Airlie