Clearing the RX FIFO will cause data loss.
Copy the pl011_enabl_interrupts implementation, and remove the clear
interrupt and FIFO part of the code.
Fixes: 211565b100 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Signed-off-by: delisun <delisun@pateo.com.cn>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221110020108.7700-1-delisun@pateo.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html
Fixes: 0dd1e247fd (drivers: PL011: add support for the ARM SBSA generic UART)
Signed-off-by: Jiamei Xie <jiamei.xie@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221117103237.86856-1-jiamei.xie@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It contains only struct uart_port, so no need for another structure.
Remove it and convert the rest to use struct uart_port directly.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of self-defined struct altera_jtaguart::imr, use preexisting
uart_port::read_status_mask.
Note that imr was ulong. But there is no reason for that, its values are
uints. And readl/writel's are used to read it/write to it.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_NORMAL is the only value it contains, so remove the variable and use
the constant instead.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local tail variable in n_tty_read() is used for one purpose, it
keeps the old tail. Thus, rename it appropriately to improve code
readability.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/22b37499-ff9a-7fc1-f6e0-58411328d122@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver
documentation update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY3fJoQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynycACgozhFjiUOjim8J0qUR943mlhTp/kAn0BVsKSk
PD8gi6Wk5SAybCpHxpsD
=Bqke
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver documentation
update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
docs/driver-api/miscellaneous: Remove kernel-doc of serial_core.c
serial: 8250: Flush DMA Rx on RLSI
serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
serial: 8250_lpss: Configure DMA also w/o DMA filter
serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
Revert "tty: n_gsm: replace kicktimer with delayed_work"
Revert "tty: n_gsm: avoid call of sleeping functions from atomic context"
serial: imx: Add missing .thaw_noirq hook
tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
serial: 8250: omap: Flush PM QOS work on remove
serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
serial: 8250_omap: remove wait loop from Errata i202 workaround
serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DMA to use 16B burst size with Elkhart Lake. This makes the
bus use more efficient and works around an issue which occurs with the
previously used 1B.
The fix was initially developed by Srikanth Thokala and Aman Kumar.
This together with the previous config change is the cleaned up version
of the original fix.
Fixes: 0a9410b981 ("serial: 8250_lpss: Enable DMA on Intel Elkhart Lake")
Cc: <stable@vger.kernel.org> # serial: 8250_lpss: Configure DMA also w/o DMA filter
Reported-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Co-developed-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.1.8.1.1 describes the parameter negotiation
messages and parameters. Chapter 5.4.1 states that the default parameters
are to be used if no negotiation is performed. Chapter 5.4.6.3.1 describes
the encoding of the parameter negotiation message. The meaning of the
parameters and allowed value ranges can be found in chapter 5.7.
Add parameter negotiation support accordingly. DLCI specific parameter
configuration by the user requires additional ioctls. This is subject to
another patch.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221103091743.2119-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.1 describes the encoding of the
parameter negotiation messages.
Add the parameters used there to 'gsm_mux' and 'gsm_dlci' and initialize both
according to the value ranges and recommended defaults defined in chapter 5.7.
Replace the use of the DLC default values from the 'gsm_mux' fields with the DLC
specific values from the 'gsm_dlci' fields where applicable.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm has a minimal protocol overhead of 7 bytes. The current code already
checks whether the configured MRU/MTU size is at least one byte more than
this.
Introduce the macro MIN_MTU to make this value more obvious.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
calculates RS485 delays from the baudrate. The baudrate is generated
with either a 16x or 13x divisor. The divisor is set in the Mode
Definition Register 1 (MDR1).
The commit erroneously assumes that the register stores the divisor as
a bitmask and uses a logical AND to differentiate between 16x and 13x
divisors. However the divisor is really stored as a 3-bit mode
(see lines 363ff in include/uapi/linux/serial_reg.h).
The logical AND operation is performed with UART_OMAP_MDR1_16X_MODE,
which is defined as 0x0 and hence yields false. So the commit always
assumes a 13x divisor. Fix by using an equal comparison. This works
because we never set any of the other 5 bits in the register. (They
pertain to IrDA mode, which is not supported by the driver).
Fixes: 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
Link: https://lore.kernel.org/linux-serial/202211070440.8hWunFUN-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/7d5b04da13d89b8708b9543a0b125f2b6062a77b.1667977259.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
brcmuart_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221109072110.117291-2-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA Rx completes, the current behavior is to just exit the DMA
completion handler without future actions. If the transfer is still
on-going, UART will trigger an interrupt and that eventually rearms the
DMA Rx. The extra interrupt round-trip has an inherent latency cost
that increases the risk of FIFO overrun. In such situations, the
latency margin tends to already be less due to FIFO not being empty.
Add check into DMA Rx completion handler to detect if LSR has DR (Data
Ready) still set. DR indicates there will be more characters pending
and DMA Rx can be rearmed right away to handle them.
Cc: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221107102126.56481-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the two instances of this typo present in the MSM and VT8500 serial
drivers.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20221104103719.2234098-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_buffer has flags which is only used for storing TTYB_NORMAL.
There is also a few quite confusing operations for checking the presense
of TTYB_NORMAL. Simplify things by converting flags to bool.
Despite the name remaining the same, the meaning of "flags" is altered
slightly by this change. Previously it referred to flags of the buffer
(only TTYB_NORMAL being used as a flag). After this change, flags tell
whether the buffer contains/should be allocated with flags array along
with character data array. It is much more suitable name that
TTYB_NORMAL was for this purpose, thus the name remains.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019105504.16800-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable "tty_legacy_tiocsti" should be defined before the kerndoc
for the tiocsti() function. The new variable was breaking the "htmldocs"
build target:
drivers/tty/tty_io.c:2271: warning: cannot understand function prototype: 'bool tty_legacy_tiocsti __read_mostly = IS_ENABLED(CONFIG_LEGACY_TIOCSTI); '
Fixes: 83efeeeb3d ("tty: Allow TIOCSTI to be disabled")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/lkml/20221107143434.66f7be35@canb.auug.org.au
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221107034631.never.637-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
gsm_dlci_t1()
gsm_dlci_open()
gsm_modem_update()
gsm_modem_upd_via_msc()
gsm_control_send()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221002040709.27849-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c9ab053e56.
The above commit is reverted as it was a prerequisite for tx_mutex
introduction and tx_mutex has been removed as it does not correctly
work in order to protect tx data.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 902e02ea93.
The above commit is reverted as the usage of tx_mutex seems not to solve
the problem described in 902e02ea93 ("tty: n_gsm: avoid call of sleeping
functions from atomic context") and just moves the bug to another place.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722a ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcab ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The symbol is not used outside of the file, so mark it static.
Fixes the following warning:
drivers/tty/hvc/hvc_rtas.c:29:19: warning: symbol 'hvc_rtas_dev' was
not declared. Should it be static?
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20221019064412.3759874-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use str_enabled_disabled() helper instead of open coding the same.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221017171633.65275-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default polarity of RS485 DE signal is active high. This driver does
not handle such case properly. Currently, when a pin is multiplexed as a
UART CTS_B on boot, this pin is pulled HIGH by the i.MX UART CTS circuit,
which activates DE signal on the RS485 transceiver and thus behave as if
the RS485 was transmitting data, so the system blocks the RS485 bus when
it starts and until user application takes over. This behavior is not OK.
The problem consists of two separate parts.
First, the i.MX UART IP requires UCR1 UARTEN and UCR2 RXEN to be set for
UCR2 CTSC and CTS bits to have any effect. The UCR2 CTSC bit permits the
driver to set CTS (RTS_B or RS485 DE signal) to either level sychronous
to the internal UART IP clock. Compared to other options, like GPIO CTS
control, this has the benefit of being synchronous to the UART IP clock
and thus without glitches or bus delays. The reason for the CTS design
is likely because when the Receiver is disabled, the UART IP can never
indicate that it is ready to receive data by assering CTS signal, so
the CTS is always pulled HIGH by default.
When the port is closed by user space, imx_uart_stop_rx() clears UCR2
RXEN bit, and imx_uart_shutdown() clears UCR1 UARTEN bit. This disables
UART Receiver and UART itself, and forces CTS signal HIGH, which leads
to the RS485 bus being blocked because RS485 DE is incorrectly active.
The proposed solution for this problem is to keep the Receiver running
even after the port is closed, but in loopback mode. This disconnects
the RX FIFO input from the RXD external signal, and since UCR2 TXEN is
cleared, the UART Transmitter is disabled, so nothing can feed data in
the RX FIFO. Because the Receiver is still enabled, the UCR2 CTSC and
CTS bits still have effect and the CTS (RS485 DE) control is retained.
Note that in case of RS485 DE signal active low, there is no problem and
no special handling is necessary. The CTS signal defaults to HIGH, thus
the RS485 is by default set to Receive and the bus is not blocked.
Note that while there is the possibility to control CTS using GPIO with
either CTS polarity, this has the downside of not being synchronous to
the UART IP clock and thus glitchy and susceptible to slow DE switching.
Second, on boot, before the UART driver probe callback is called, the
driver core triggers pinctrl_init_done() and configures the IOMUXC to
default state. At this point, UCR1 UARTEN and UCR2 RXEN are both still
cleared, but UART CTS_B (RS485 DE) is configured as CTS function, thus
the RTS signal is pulled HIGH by the UART IP CTS circuit.
One part of the solution here is to enable UCR1 UARTEN and UCR2 RXEN and
UTS loopback in this driver probe callback, thus unblocking the CTSC and
CTS control early on. But this is still too late, since the pin control
is already configured and CTS has been pulled HIGH for a short period
of time.
When Linux kernel boots and this driver is bound, the pin control is set
to special "init" state if the state is available, and driver can switch
the "default" state afterward when ready. This state can be used to set
the CTS line as a GPIO in DT temporarily, and a GPIO hog can force such
GPIO to LOW, thus keeping the RS485 DE line LOW early on boot. Once the
driver takes over and UCR1 UARTEN and UCR2 RXEN and UTS loopback are all
enabled, the driver can switch to "default" pin control state and control
the CTS line as function instead. DT binding example is below:
"
&gpio6 {
rts-init-hog {
gpio-hog;
gpios = <5 0>;
output-low;
line-name = "rs485-de";
};
};
&uart5 { /* DHCOM UART2 */
pinctrl-0 = <&pinctrl_uart5>;
pinctrl-1 = <&pinctrl_uart5_init>;
pinctrl-names = "default", "init";
...
};
pinctrl_uart5_init: uart5-init-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x30b1
>;
};
pinctrl_uart5: uart5-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x30b1
>;
};
"
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220929144400.13571-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221028110044.54719-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM runtime")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013112339.2540767-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where omap8250_set_mctrl() may get called after the
UART has already autoidled causing an asynchronous external abort.
This can happen on ttyport_open():
mem_serial_in from omap8250_set_mctrl+0x38/0xa0
omap8250_set_mctrl from uart_update_mctrl+0x4c/0x58
uart_update_mctrl from uart_dtr_rts+0x60/0xa8
uart_dtr_rts from tty_port_block_til_ready+0xd0/0x2a8
tty_port_block_til_ready from uart_open+0x14/0x1c
uart_open from ttyport_open+0x64/0x148
And on ttyport_close():
omap8250_set_mctrl from uart_update_mctrl+0x3c/0x48
uart_update_mctrl from uart_dtr_rts+0x54/0x9c
uart_dtr_rts from tty_port_shutdown+0x78/0x9c
tty_port_shutdown from tty_port_close+0x3c/0x74
tty_port_close from ttyport_close+0x40/0x58
It can also happen on disassociate_ctty() calling uart_shutdown()
that ends up calling omap8250_set_mctrl().
Let's fix the issue by adding missing PM runtime calls to
omap8250_set_mctrl(). To do this, we need to add __omap8250_set_mctrl()
that can be called from both omap8250_set_mctrl(), and from runtime PM
resume path when restoring the registers.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221024063613.25943-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JZ4750/55/60 (but not JZ4760b) have an optional /2 divider between the
EXT oscillator and some peripherals including UART, which will
be enabled if using a 24 MHz oscillator, and disabled when
using a 12 MHz oscillator.
This behavior relies on hardware differences: most boards (if not all)
with those SoCs have 12 or 24 MHz oscillators but many peripherals want
12Mhz to operate properly (AIC and USB-PHY at least).
The 16MHz threshold looks arbitrary but used in vendor's bootloader code
for enable the divider.
The patch doesn't affect JZ4760's behavior as it is subject for another
patchset with re-classification of all supported ingenic UARTs.
Link: https://github.com/carlos-wong/uboot_jz4755/blob/master/cpu/mips/jz_serial.c#L158
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221031184041.1338129-3-lis8215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the DMA status before terminating the DMA, as doing so deletes
the DMA desc.
Also, to get the correct transfer status information, pause the DMA
using dmaengine_pause() before reading the DMA status.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Link: https://lore.kernel.org/r/1666105086-17326-1-git-send-email-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-34-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-29-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-22-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-18-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-By: Richard GENOUD <richard.genoud@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent TI Sitara SoCs such as AM64/AM65 have gained the ability to
automatically assert RTS when data is transmitted, obviating the need
to emulate this functionality in software.
The feature is controlled through new DIR_EN and DIR_POL bits in the
Mode Definition Register 3. For details see page 8783 and 8890 of the
AM65 TRM: https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Bin Liu <b-liu@ti.com>
Tested-by: Zeng Chao <chao.zeng@siemens.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/e9f25f5c9200a35d3162973c2b45d6b892cc9bf2.1665906869.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added changes to support the hibernation feature for serial UART.
Added support for freeze, restore and thaw callbacks to put the
device into hibernation.
Signed-off-by: Aniket Randive <quic_arandive@quicinc.com>
Link: https://lore.kernel.org/r/1665123780-20557-1-git-send-email-quic_arandive@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port_tx_limited() is a new helper to send characters to the device.
Use it in these drivers.
mux.c also needs to define tx_done(). But I'm not sure if the driver
really wants to wait for all the characters to dismiss from the HW fifo
at this code point. Hence I marked this as FIXME.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: linux-riscv@lists.infradead.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221004104927.14361-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSTI continues its long history of being used in privilege escalation
attacks[1]. Prior attempts to provide a mechanism to disable this have
devolved into discussions around creating full-blown LSMs to provide
arbitrary ioctl filtering, which is hugely over-engineered -- only
TIOCSTI is being used this way. 3 years ago OpenBSD entirely removed
TIOCSTI[2], Android has had it filtered for longer[3], and the tools that
had historically used TIOCSTI either do not need it, are not commonly
built with it, or have had its use removed.
Provide a simple CONFIG and global sysctl to disable this for the system
builders who have wanted this functionality for literally decades now,
much like the ldisc_autoload CONFIG and sysctl.
[1] https://lore.kernel.org/linux-hardening/Y0m9l52AKmw6Yxi1@hostpad
[2] https://undeadly.org/cgi?action=article;sid=20170701132619
[3] https://lore.kernel.org/lkml/CAFJ0LnFGRuEEn1tCLhoki8ZyWrKfktbF+rwwN7WzyC_kBFoQVA@mail.gmail.com/
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Simon Brand <simon.brand@postadigitale.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022182949.2684794-2-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding another sysctl to the tty subsystem, move the
tty setup code into the "core" tty code, which contains tty_init() itself.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022182949.2684794-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/23f608ca57e7e19bc7060d3e563de383e0b2b337.1665033575.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to enabled if SOC_CANAAN.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221005171348.167476-4-conor@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to the value of SOC_SIFIVE.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221005171348.167476-3-conor@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file name of this driver is misleading - it handles various serial
ports on parisc machines, not just such on the GSC bus.
Rename the file to make this clearer.
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
* Convert the PDC console to an early console
* Unbreak mmap() of graphics card memory due to PAGE_SPECIAL pgtable flag
* Reduce the size of the alternative tables
* Align stifb graphics card memory size to 4MB
* Spelling fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY0mnYAAKCRD3ErUQojoP
X1z3AQC204Pq725WM3rgEomIqFjk8QaU2UFcNQ74a52V3AUiiQD8C0DFmWDbssUv
ZE5uC+ySlNd1hLkL3QYxrbbwuL+y+Q0=
=YvFZ
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Fixes:
- When we added basic vDSO support in kernel 5.18 we introduced a bug
which prevented a mmap() of graphic card memory. This is because we
used the DMB (data memory break trap bit) page flag as special-bit,
but missed to clear that bit when loading the TLB.
- Graphics card memory size was not correctly aligned
- Spelling fixes (from Colin Ian King)
Enhancements:
- PDC console (which uses firmware calls) now rewritten as early
console
- Reduced size of alternative tables"
* tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix spelling mistake "mis-match" -> "mismatch" in eisa driver
parisc: Fix userspace graphics card breakage due to pgtable special bit
parisc: fbdev/stifb: Align graphics memory size to 4MB
parisc: Convert PDC console to an early console
parisc: Reduce kernel size by packing alternative tables
Rewrite the PDC console to become an early console.
Beside the fact that now boot information is visible until another
(text- or graphics) console takes over, this benefits as well machines
with a yet-unsupported STI console and kgdb.
Signed-off-by: Helge Deller <deller@gmx.de>
Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to
finally get this work done
- tty serial transmit cleanups in various drivers in preparation
for more cleanup and unification in future releases (that work
was not ready for this release.)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BSdA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylucQCfaXIrYuh2AHcb6+G+Nqp1xD2BYaEAoIdLyOCA
a2yziLrDF6us2oav6j4x
=Wv+X
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent
ones.
I also did a cleanup of the old Footbridge platform, which was
the last holdout for the phys_to_dma()/dma_to_phys() interface
that is now completely gone from arm32, completing work started
by Christoph Hellwig.
-----BEGIN PGP SIGNATURE-----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=xsKV
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent ones.
I also did a cleanup of the old Footbridge platform, which was the
last holdout for the phys_to_dma()/dma_to_phys() interface that is now
completely gone from arm32, completing work started by Christoph
Hellwig"
* tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: aspeed: Kconfig: Fix indentation
ARM: Drop CMDLINE_* dependency on ATAGS
ARM: Drop CMDLINE_FORCE dependency on !ARCH_MULTIPLATFORM
ARM: s3c: remove orphan declarations from arch/arm/mach-s3c/devs.h
pxa: Drop if with an always false condition
ARM: orion: fix include path
ARM: shmobile: Drop selecting SOC_BUS
arm64: renesas: Drop selecting SOC_BUS
ARM: disallow PCI with MMU=n again
ARM: footbridge: remove custom DMA address handling
MAINTAINERS: Add BCM4908 maintainer to BCMBCA entry
ARM: footbridge: move isa-dma support into footbridge
ARM: footbridge: remove leftover from personal-server
ARM: footbridge: remove addin mode
arm64: Kconfig.platforms: Group NXP platforms together
arm64: Kconfig.platforms: Re-organized Broadcom menu
ARM: make ARCH_MULTIPLATFORM user-visible
ARM: fix XIP_KERNEL dependencies
ARM: Kconfig: clean up platform selection
ARM: simplify machdirs/platdirs handling
...
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
The following message is seen during boot and the activation of
console port gets delayed until normal serial ports activation.
[ 0.001346] irq: no irq domain found for pic@930 !
The console port doesn't need irq, perform irq reservation later,
during cpm_uart probe.
While at it, don't use NO_IRQ but 0 which is the value returned
by irq_of_parse_and_map() in case of error. By chance powerpc's
NO_IRQ has value 0 but on some architectures it is -1.
Fixes: 14d893fc68 ("powerpc/8xx: Convert CPM1 interrupt controller to platform_device")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/8bed0f30c2e9ef16ae64fb1243a16d54a48eb8da.1664526717.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
delisun