As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.2-rc5 that resolve
a number of tiny reported issues and some new device ids. They include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY8wDQA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGegCguB+ZpDHKt9wccrGP3h/dwT2MAm8AnAqG4bmy
Yw/cHHPt9gx+AW6RBtAL
=EymN
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Add support for Sealevel 7xxxC serial cards.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f24771b62a as it is
reported to break the build.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com
Fixes: f24771b62a ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler")
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Valentin Caron <valentin.caron@foss.st.com> # V3
Cc: Marek Vasut <marex@denx.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When -Woverride-init is enabled in a build, gcc points out that
qcom_geni_serial_pm_ops contains conflicting initializers:
drivers/tty/serial/qcom_geni_serial.c:1586:20: error: initialized field overwritten [-Werror=override-init]
1586 | .restore = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/qcom_geni_serial.c:1586:20: note: (near initialization for 'qcom_geni_serial_pm_ops.restore')
drivers/tty/serial/qcom_geni_serial.c:1587:17: error: initialized field overwritten [-Werror=override-init]
1587 | .thaw = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Open-code the initializers with the version that was already used,
and use the pm_sleep_ptr() method to deal with unused ones,
in place of the __maybe_unused annotation.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221215165453.1864836-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ba47f97a18 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112180417.25595-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20230108181735.10937-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer.
Fixes: f9d690b6ec ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several mutexes are taken while setting up console serial ports. In
particular, the tty_port->mutex and @console_mutex are taken:
serial_pnp_probe
serial8250_register_8250_port
uart_add_one_port (locks tty_port->mutex)
uart_configure_port
register_console (locks @console_mutex)
In order to synchronize kgdb's tty_find_polling_driver() with
register_console(), commit 6193bc9084 ("tty: serial: kgdboc:
synchronize tty_find_polling_driver() and register_console()") takes
the @console_mutex. However, this leads to the following call chain
(with locking):
platform_probe
kgdboc_probe
configure_kgdboc (locks @console_mutex)
tty_find_polling_driver
uart_poll_init (locks tty_port->mutex)
uart_set_options
This is clearly deadlock potential due to the reverse lock ordering.
Since uart_set_options() requires holding @console_mutex in order to
serialize early initialization of the serial-console lock, take the
@console_mutex in uart_poll_init() instead of configure_kgdboc().
Since configure_kgdboc() was using @console_mutex for safe traversal
of the console list, change it to use the SRCU iterator instead.
Add comments to uart_set_options() kerneldoc mentioning that it
requires holding @console_mutex (aka the console_list_lock).
Fixes: 6193bc9084 ("tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Export console_srcu_read_lock_is_held() to fix build kgdboc as a module.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230112161213.1434854-1-john.ogness@linutronix.de
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY76ohgAKCRCAXGG7T9hj
vo8fAP0XJ94B7asqcN4W3EyeyfqxUf1eZvmWRhrbKqpLnmHLaQEA/uJBkXL49Zj7
TTcbxR1coJ/hPwhtmONU4TNtCZ+RXw0=
=2Ib5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two cleanup patches
- a fix of a memory leak in the Xen pvfront driver
- a fix of a locking issue in the Xen hypervisor console driver
* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: free active map buffer on pvcalls_front_free_map
hvc/xen: lock console list traversal
x86/xen: Remove the unused function p2m_index()
xen: make remove callback of xen driver void returned
The currently lockless access to the xen console list in
vtermno_to_xencons() is incorrect, as additions and removals from the
list can happen anytime, and as such the traversal of the list to get
the private console data for a given termno needs to happen with the
lock held. Note users that modify the list already do so with the
lock taken.
Adjust current lock takers to use the _irq{save,restore} helpers,
since the context in which vtermno_to_xencons() is called can have
interrupts disabled. Use the _irq{save,restore} set of helpers to
switch the current callers to disable interrupts in the locked region.
I haven't checked if existing users could instead use the _irq
variant, as I think it's safer to use _irq{save,restore} upfront.
While there switch from using list_for_each_entry_safe to
list_for_each_entry: the current entry cursor won't be removed as
part of the code in the loop body, so using the _safe variant is
pointless.
Fixes: 02e19f9c7c ('hvc_xen: implement multiconsole support')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20221130163611.14686-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some small
incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of serial
drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wt5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSiACffLCC9SFnP1ClJJh73OpCN11alDAAoIfMct2A
/zrJ4on7o0YQU1Ilg2+k
=eD/I
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some
small incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of
serial drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits)
serial: atmel: don't stop the transmitter when doing PIO
serial: atmel: cleanup atmel_start+stop_tx()
tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
serial: sunsab: Fix error handling in sunsab_init()
serial: altera_uart: fix locking in polling mode
serial: pch: Fix PCI device refcount leak in pch_request_dma()
tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused
tty: serial: fsl_lpuart: Add runtime pm support
tty: serial: fsl_lpuart: enable wakeup source for lpuart
serdev: Replace poll loop by readx_poll_timeout() macro
tty: synclink_gt: unwind actions in error path of net device open
serial: stm32: move dma_request_chan() before clk_prepare_enable()
dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity'
serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
serial: amba-pl011: avoid SBSA UART accessing DMACR register
tty: serial: altera_jtaguart: remove struct altera_jtaguart
tty: serial: altera_jtaguart: use uart_port::read_status_mask
tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs
tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars()
n_tty: Rename tail to old_tail in n_tty_read()
...
Since commit fc7a6209d5 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense for
any bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for xen bus based drivers.
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Link: https://lore.kernel.org/r/TYCP286MB23238119AB4DF190997075C9CAE39@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Juergen Gross <jgross@suse.com>
-----BEGIN PGP SIGNATURE-----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=1PTZ
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add NMI-safe SRCU reader API. It uses atomic_inc() instead of
this_cpu_inc() on strong load-store architectures.
- Introduce new console_list_lock to synchronize a manipulation of the
list of registered consoles and their flags.
This is a first step in removing the big-kernel-lock-like behavior of
console_lock(). This semaphore still serializes console->write()
calbacks against:
- each other. It primary prevents potential races between early
and proper console drivers using the same device.
- suspend()/resume() callbacks and init() operations in some
drivers.
- various other operations in the tty/vt and framebufer
susbsystems. It is likely that console_lock() serializes even
operations that are not directly conflicting with the
console->write() callbacks here. This is the most complicated
big-kernel-lock aspect of the console_lock() that will be hard
to untangle.
- Introduce new console_srcu lock that is used to safely iterate and
access the registered console drivers under SRCU read lock.
This is a prerequisite for introducing atomic console drivers and
console kthreads. It will reduce the complexity of serialization
against normal consoles and console_lock(). Also it should remove the
risk of deadlock during critical situations, like Oops or panic, when
only atomic consoles are registered.
- Check whether the console is registered instead of enabled on many
locations. It was a historical leftover.
- Cleanly force a preferred console in xenfb code instead of a dirty
hack.
- A lot of code and comment clean ups and improvements.
* tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (47 commits)
printk: htmldocs: add missing description
tty: serial: sh-sci: use setup() callback for early console
printk: relieve console_lock of list synchronization duties
tty: serial: kgdboc: use console_list_lock to trap exit
tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()
tty: serial: kgdboc: use console_list_lock for list traversal
tty: serial: kgdboc: use srcu console list iterator
proc: consoles: use console_list_lock for list iteration
tty: tty_io: use console_list_lock for list synchronization
printk, xen: fbfront: create/use safe function for forcing preferred
netconsole: avoid CON_ENABLED misuse to track registration
usb: early: xhci-dbc: use console_is_registered()
tty: serial: xilinx_uartps: use console_is_registered()
tty: serial: samsung_tty: use console_is_registered()
tty: serial: pic32_uart: use console_is_registered()
tty: serial: earlycon: use console_is_registered()
tty: hvc: use console_is_registered()
efi: earlycon: use console_is_registered()
tty: nfcon: use console_is_registered()
serial_core: replace uart_console_enabled() with uart_console_registered()
...
When setting up the early console, the setup() callback of the
regular console is used. It is called manually before registering
the early console instead of providing a setup() callback for the
early console. This is probably because the early setup needs a
different @options during the early stage.
The issue here is that the setup() callback is called without the
console_list_lock held and functions such as uart_set_options()
expect that.
Rather than manually calling the setup() function before registering,
provide an early console setup() callback that will use the different
early options. This ensures that the error checking, ordering, and
locking context when setting up the early console are correct.
Since this early console can only be registered via the earlyprintk=
parameter, the @options argument of the setup() callback will always
be NULL. Rather than simply ignoring the argument, add a WARN_ON()
to get our attention in case the setup() callback semantics should
change in the future.
Note that technically the current implementation works because it is
only used in early boot. And since the early console setup is
performed before registering, it cannot race with anything and thus
does not need any locking. However, longterm maintenance is easier
when drivers rely on the subsystem API rather than manually
implementing steps that could cause breakage in the future.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
kgdboc_earlycon_init() uses the console_lock to ensure that no consoles
are unregistered until the kgdboc_earlycon is setup. The console_list_lock
should be used instead because list synchronization responsibility will
be removed from the console_lock in a later change.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-39-john.ogness@linutronix.de
Calling tty_find_polling_driver() can lead to uart_set_options() being
called (via the poll_init() callback of tty_operations) to configure the
uart. But uart_set_options() can also be called by register_console()
(via the setup() callback of console).
Take the console_list_lock to synchronize against register_console() and
also use it for console list traversal. This also ensures the console list
cannot change until the polling console has been chosen.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-38-john.ogness@linutronix.de
configure_kgdboc() uses the console_lock for console list iteration. Use
the console_list_lock instead because list synchronization responsibility
will be removed from the console_lock in a later change.
The SRCU iterator could have been used here, but a later change will
relocate the locking of the console_list_lock to also provide
synchronization against register_console().
Note, the console_lock is still needed to serialize the device()
callback with other console operations.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-37-john.ogness@linutronix.de
Use srcu console list iteration for safe console list traversal.
Note that this is a preparatory change for when console_lock no
longer provides synchronization for the console list.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-36-john.ogness@linutronix.de
show_cons_active() uses the console_lock to gather information
on registered consoles. It requires that no consoles are unregistered
until it is finished. The console_list_lock should be used because
list synchronization responsibility will be removed from the
console_lock in a later change.
Note, the console_lock is still needed to serialize the device()
callback with other console operations.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-34-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-30-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-29-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-28-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-27-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-26-john.ogness@linutronix.de
All users of uart_console_enabled() really want to know if a console
is registered. It is not reliable to check for CON_ENABLED in order
to identify if a console is registered. Use console_is_registered()
instead.
A _locked() variant is provided because uart_set_options() is always
called with the console_list_lock held and must check if a console
is registered in order to synchronize with kgdboc.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-23-john.ogness@linutronix.de
show_cons_active() uses the console_lock to gather information
on registered consoles. Since the console_lock is being used for
multiple reasons, explicitly document these reasons. This will
be useful when the console_lock is split into fine-grained
locking.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-10-john.ogness@linutronix.de
kgdboc_earlycon_init() uses the console_lock to ensure that no consoles
are unregistered until the kgdboc_earlycon is setup. This is necessary
because the trapping of the exit() callback assumes that the exit()
callback is not called before the trap is setup.
Explicitly document this non-typical console_lock usage.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-9-john.ogness@linutronix.de
Unprotected list walks are not necessarily safe.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-2-john.ogness@linutronix.de
The devnode() in struct class should not be modifying the device that is
passed into it, so mark it as a const * and propagate the function
signature changes out into all relevant subsystems that use this
callback.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Justin Sanders <justin@coraid.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Cc: Liam Mark <lmark@codeaurora.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Cc: John Stultz <jstultz@google.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sean Young <sean@mess.org>
Cc: Frank Haverkamp <haver@linux.ibm.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Xie Yongji <xieyongji@bytedance.com>
Cc: Gautam Dawar <gautam.dawar@xilinx.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Cc: alsa-devel@alsa-project.org
Cc: dri-devel@lists.freedesktop.org
Cc: kvm@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-block@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20221123122523.1332370-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing ATMEL_US_TXDIS to ATMEL_US_CR makes the transmitter NOT to send
the just queued character. This means when the character is last and
uart calls ops->stop_tx(), the character is not sent at all.
The usart datasheet is not much specific on this, it just says the
transmitter is stopped. But apparently, the character is dropped. So
we should stop the transmitter only for DMA and PDC transfers to not
send any more characters. For PIO, this is unexpected and deviates from
other drivers. In particular, the below referenced commit broke TX as it
added a call to ->stop_tx() after the very last character written to the
transmitter.
So fix this by limiting the write of ATMEL_US_TXDIS to DMA transfers
only.
Even there, I don't know if it is correctly implemented. Are all the
queued characters sent once ->start_tx() is called? Anyone tested flow
control -- be it hard (RTSCTS) or the soft (XOFF/XON) one?
Fixes: 2d141e683e ("tty: serial: use uart_port_tx() helper")
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123082736.24566-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define local variables holding information about whether pdc or dma is
used in the HW. These are retested several times by calls to
atmel_use_pdc_tx() and atmel_use_dma_tx(). So to make the code more
readable, simply cache the values.
This is also a preparatory patch for the next one (where is_pdc is used
once more in atmel_stop_tx()).
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123082736.24566-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221123023619.30173-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
Fixes: c4d37215a8 ("[SERIAL] sunsab: Convert to of_driver framework.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221123061212.52593-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since altera_uart_interrupt() may also be called from
a poll timer in "serving_softirq" context, use
spin_[lock_irqsave|unlock_irqrestore] variants, which
are appropriate for both softirq and hardware interrupt
contexts.
Fixes: 2f8b9c15cd ("altera_uart: Add support for polling mode (IRQ-less)")
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20221122200426.888349-1-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Fixes: 3c6a483275 ("Serial: EG20T: add PCH_UART driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221122114559.27692-1-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_ptr() to remove the need to mark the pm functions as
__maybe_unused when the kernel is built without CONFIG_PM support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART supports both synchronous wakeup and asynchronous wakeup(wakeup
the system when the UART clocks are shut-off), the synchronous wakeup is
configured by UARTCTRL_RIE interrupt, and the asynchronous wakeup is
configured by UARTBAUD_RXEDGIE interrupt.
Add lpuart_uport_is_active() to determine if the uart port needs to get
into the suspend states, also add lpuart_suspend_noirq() and
lpuart_resume_noirq() to enable and disable the wakeup irq bits if the
uart port needs to be set as wakeup source.
When use lpuart with DMA mode, it still needs to switch to the cpu mode
in .suspend() that enable cpu interrupts RIE and RXEDGIE as wakeup
source, after system resume back, needs to setup DMA again, .resume()
will share the HW setup code with .startup(), so abstract the same code
to the api like lpuart32_hw_setup().
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resent again, last attempt still altered the plain text.
Zhengchao Shao <shaozhengchao@huawei.com> identified by inspection bugs in the error path of hdlcdev_open() in synclink_gt.c
The function did not fully unwind actions in the error path. The use of try_module_get()/module_put() is unnecessary, potentially hazardous and is removed. The synclink_gt driver is already pinned any point the net device is registered, a requirement for calling this entry point.
The call hdlc_open() to init the generic HDLC layer is moved to after driver level init/checks and proper rollback of previous actions is added. This is a more sensible ordering as the most common error paths are at the driver level and the driver level rollbacks require less processing than hdlc_open()/hdlc_close().
This has been tested with supported hardware.
Signed-off-by:Paul Fulghum <paulkf@microgate.com>
Link: https://lore.kernel.org/r/7599F007-8985-4469-BE00-52BD1530210E@microgate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_chan() returns a PROBE_DEFER error, clk_disable_unprepare()
will be called and USART clock will be disabled. But early console can be
still active on the same USART.
While moving dma_request_chan() before clk_prepare_enable(), the clock
won't be taken in case of a DMA PROBE_DEFER error, and so it doesn't need
to be disabled. Then USART is still clocked for early console.
Fixes: a7770a4bfc ("serial: stm32: defer probe for dma devices")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20221118170602.1057863-1-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
George Kennedy