Back in the description of commit e440e30e26 ("arm64: dts: qcom:
sc7180: Avoid glitching SPI CS at bootup on trogdor") we described a
problem that we were seeing on trogdor devices. I'll re-summarize here
but you can also re-read the original commit.
On trogdor devices, the BIOS is setting up the SPI chip select as:
- mux special function (SPI chip select)
- output enable
- output low (unused because we've muxed as special function)
In the kernel, however, we've moved away from using the chip select
line as special function. Since the kernel wants to fully control the
chip select it's far more efficient to treat the line as a GPIO rather
than sending packet-like commands to the GENI firmware every time we
want the line to toggle.
When we transition from how the BIOS had the pin configured to how the
kernel has the pin configured we end up glitching the line. That's
because we _first_ change the mux of the line and then later set its
output. This glitch is bad and can confuse the device on the other end
of the line.
The old commit e440e30e26 ("arm64: dts: qcom: sc7180: Avoid
glitching SPI CS at bootup on trogdor") fixed the glitch, though the
solution was far from elegant. It essentially did the thing that
everyone always hates: encoding a sequential program in device tree,
even if it's a simple one. It also, unfortunately, got broken by
commit b991f8c362 ("pinctrl: core: Handling pinmux and pinconf
separately"). After that commit we did all the muxing _first_ even
though the config (set the pin to output high) was listed first. :(
I looked at ideas for how to solve this more properly. My first
thought was to use the "init" pinctrl state. In theory the "init"
pinctrl state is supposed to be exactly for achieving glitch-free
transitions. My dream would have been for the "init" pinctrl to do
nothing at all. That would let us delay the automatic pin muxing until
the driver could set things up and call pinctrl_init_done(). In other
words, my dream was:
/* Request the GPIO; init it 1 (because DT says GPIO_ACTIVE_LOW) */
devm_gpiod_get_index(dev, "cs", GPIOD_OUT_LOW);
/* Output should be right, so we can remux, yay! */
pinctrl_init_done(dev);
Unfortunately, it didn't work out. The primary reason is that the MSM
GPIO driver implements gpio_request_enable(). As documented in
pinmux.h, that function automatically remuxes a line as a GPIO. ...and
it does this remuxing _before_ specifying the output of the pin. You
can see in gpiod_get_index() that we call gpiod_request() before
gpiod_configure_flags(). gpiod_request() isn't passed any flags so it
has no idea what the eventual output will be.
We could have debates about whether or not the automatic remuxing to
GPIO for the MSM pinctrl was a good idea or not, but at this point I
think there is a plethora of code that's relying on it and I certainly
wouldn't suggest changing it.
Alternatively, we could try to come up with a way to pass the initial
output state to gpio_request_enable() and plumb all that through. That
seems like it would be doable, but we'd have to plumb it through
several layers in the stack.
This patch implements yet another alternative. Here, we specifically
avoid glitching the first time a pin is muxed to GPIO function if the
direction of the pin is output. The idea is that we can read the state
of the pin before we set the mux and make sure that the re-mux won't
change the state.
NOTES:
- We only do this the first time since later swaps between mux states
might want to preserve the old output value. In other words, I
wouldn't want to break a driver that did:
gpiod_set_value(g, 1);
pinctrl_select_state(pinctrl, special_state);
pinctrl_select_default_state();
/* We should be driving 1 even if "special_state" made the pin 0 */
- It's safe to do this the first time since the driver _couldn't_ have
explicitly set a state. In order to even be able to control the GPIO
(at least using gpiod) we have to have requested it which would have
counted as the first mux.
- In theory, instead of keeping track of the first time a pin was set
as a GPIO we could enable the glitch-free behavior only when
msm_pinmux_request_gpio() is in the callchain. That works an enables
my "dream" implementation above where we use an "init" state to
solve this. However, it's nice not to have to do this. By handling
just the first transition to GPIO we can simply let the normal
"default" remuxing happen and we can be assured that there won't be
a glitch.
Before this change I could see the glitch reported on the EC console
when booting. It would say this when booting the kernel:
Unexpected state 1 in CSNRE ISR
After this change there is no error reported.
Note that I haven't reproduced the original problem described in
e440e30e26 ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at
bootup on trogdor") but I could believe it might happen in certain
timing conditions.
Fixes: b991f8c362 ("pinctrl: core: Handling pinmux and pinconf separately")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20221014103217.1.I656bb2c976ed626e5d37294eb252c1cf3be769dc@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some laptops have been reported to wake up from s2idle when plugging
in the AC adapter or by closing the lid. This is a surprising
behavior that is further clarified by commit cb3e7d624c ("PM:
wakeup: Add extra debugging statement for multiple active IRQs").
With that commit in place the following interaction can be seen
when the lid is closed:
[ 28.946038] PM: suspend-to-idle
[ 28.946083] ACPI: EC: ACPI EC GPE status set
[ 28.946101] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.950152] Timekeeping suspended for 3.320 seconds
[ 28.950152] PM: Triggering wakeup from IRQ 9
[ 28.950152] ACPI: EC: ACPI EC GPE status set
[ 28.950152] ACPI: EC: ACPI EC GPE dispatched
[ 28.995057] ACPI: EC: ACPI EC work flushed
[ 28.995075] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.995131] PM: Triggering wakeup from IRQ 9
[ 28.995271] ACPI: EC: ACPI EC GPE status set
[ 28.995291] ACPI: EC: ACPI EC GPE dispatched
[ 29.098556] ACPI: EC: ACPI EC work flushed
[ 29.207020] ACPI: EC: ACPI EC work flushed
[ 29.207037] ACPI: PM: Rearming ACPI SCI for wakeup
[ 29.211095] Timekeeping suspended for 0.739 seconds
[ 29.211095] PM: Triggering wakeup from IRQ 9
[ 29.211079] PM: Triggering wakeup from IRQ 7
[ 29.211095] ACPI: PM: ACPI non-EC GPE wakeup
[ 29.211095] PM: resume from suspend-to-idle
* IRQ9 on this laptop is used for the ACPI SCI.
* IRQ7 on this laptop is used for the GPIO controller.
What has occurred is when the lid was closed the EC woke up the
SoC from it's deepest sleep state and the kernel's s2idle loop
processed all EC events. When it was finished processing EC events,
it checked for any other reasons to wake (break the s2idle loop).
The IRQ for the GPIO controller was active so the loop broke, and
then this IRQ was processed. This is not a kernel bug but it is
certainly a surprising behavior, and to better debug it we should
have a dynamic debugging message that we can enact to catch it.
Acked-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20221013134729.5592-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OF node in the GPIO library is deprecated and soon
will be removed.
GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20221010075615.43244-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without ->gpio_request_enable() and ->gpio_set_direction()
callbacks it's not possible to mux GPIO via standard GPIO
interfaces (like `gpioget` or `gpioset` tools in user space).
Implement those functions to fill the above mentioned gap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221010125221.28275-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding persist state case to atmel_conf_pin_config_group_set() function.
After adding configuration support for userspace gpiod api, there was an
extra flag PIN_CONFIG_PERSIST_STATE that was not passed in before.
Based on other drivers like TI drivers, added a switch case and return
ENOTSUPP in that case.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221007151647.98222-3-Ryan.Wanner@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding support for line bias flags that have been implented in gpio API.
There are functions in the gpiod library that can control line bias from
userspace this adds that functionality to this driver.
Adding .pin_config_set allows the driver's pin configuration to be
accessed from userspace. The general idea for this as been taken from
stm32, intel, and rockchip drivers that have userspace access for bias
flags.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> # on sama5d27 som1 ek
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221007151647.98222-2-Ryan.Wanner@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some mt7986 boards use uart rts/cts pins as gpio,
This patch allows to change rts/cts to gpio mode, but keep
rx/tx as UART function.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Link: https://lore.kernel.org/r/20221008164807.113590-1-linux@fw-web.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes UART1 function bits and MMC groups typo.
For pins 0x97,0x99 function 0 is designated to PWM3/PWM5
respectively, function is 1 designated to the UART1.
Diff from v1:
- sent separately
- added tag Fixes
Cc: stable@vger.kernel.org
Fixes: b582b5a434 ("pinctrl: Ingenic: Add pinctrl driver for JZ4755.")
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016153548.3024209-1-lis8215@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Snapdragon 670 has a Top-Level Mode Multiplexer (TLMM) for various
features. Add a driver to support it.
Link: de5a12173c%5E%21/#F6
Link: 04f083156d%5E%21/#F22
Link: 54837652e3%5E%21/#F0
Link: f0409b0717%5E%21/#F0
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221014001934.4995-4-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It may be necessary for some devices to specify reserved gpios in the
device-specific DTS, in addition to the reserved gpios common to all
devices with a given SoC. Remove this bitmap_fill() call so that the
settings applied to the gpio valid mask by DTS are not overridden by
the driver's reserved gpios.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221014001934.4995-3-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using devm_add_action_or_reset() to make workqueue device-managed, so it can be
destroy whenever the driver is unbound.
Fixes: c297561bc9 ("pinctrl: ocelot: Fix interrupt controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220925021258.1492905-1-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221005133337.19245-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Core code:
- Provide a generic wrapper which can be utilized in drivers to handle
the problem of force threaded demultiplex interrupts on RT enabled
kernels. This avoids conditionals and horrible quirks in drivers all
over the place.
- Fix up affected pinctrl and GPIO drivers to make them cleanly RT safe.
- Interrupt drivers:
- A new driver for the FSL MU platform specific MSI implementation.
- Make irqchip_init() available for pure ACPI based systems.
- Provide a functional DT binding for the Realtek RTL interrupt chip.
- The usual DT updates and small code improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=2ok5
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt updates from Thomas Gleixner:
"Core code:
- Provide a generic wrapper which can be utilized in drivers to
handle the problem of force threaded demultiplex interrupts on RT
enabled kernels. This avoids conditionals and horrible quirks in
drivers all over the place
- Fix up affected pinctrl and GPIO drivers to make them cleanly RT
safe
Interrupt drivers:
- A new driver for the FSL MU platform specific MSI implementation
- Make irqchip_init() available for pure ACPI based systems
- Provide a functional DT binding for the Realtek RTL interrupt chip
- The usual DT updates and small code improvements all over the
place"
* tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
irqchip: IMX_MU_MSI should depend on ARCH_MXC
irqchip/imx-mu-msi: Fix wrong register offset for 8ulp
irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap
dt-bindings: irqchip: Describe the IMX MU block as a MSI controller
irqchip: Add IMX MU MSI controller driver
dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support
irqchip/gic-v3: Fix typo in comment
dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding
dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells
irqchip: Allow extra fields to be passed to IRQCHIP_PLATFORM_DRIVER_END
platform-msi: Export symbol platform_msi_create_irq_domain()
irqchip/realtek-rtl: use parent interrupts
dt-bindings: interrupt-controller: realtek,rtl-intc: require parents
irqchip/realtek-rtl: use irq_domain_add_linear()
irqchip: Make irqchip_init() usable on pure ACPI systems
bcma: gpio: Use generic_handle_irq_safe()
gpio: mlxbf2: Use generic_handle_irq_safe()
platform/x86: intel_int0002_vgpio: Use generic_handle_irq_safe()
ssb: gpio: Use generic_handle_irq_safe()
pinctrl: amd: Use generic_handle_irq_safe()
...
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup.
- Mediatek MT8188 SoC pin control support.
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem)
pin control support.
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support.
Improvements:
- Fix some missing pins in the Armada 37xx driver.
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP() macro.
- Fix some GPIO irq_chips to be immutable.
- Massive Qualcomm device tree binding cleanup, with more to come.
-----BEGIN PGP SIGNATURE-----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=PvLX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is nothing exciting going on, no core changes, just a few
drivers and cleanups.
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup
- Mediatek MT8188 SoC pin control support
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem) pin
control support
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support
Improvements:
- Fix some missing pins in the Armada 37xx driver
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP()
macro
- Fix some GPIO irq_chips to be immutable
- Massive Qualcomm device tree binding cleanup, with more to come"
* tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (119 commits)
MAINTAINERS: adjust STARFIVE JH7100 PINCTRL DRIVER after file movement
pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100"
pinctrl: Create subdirectory for StarFive drivers
dt-bindings: pinctrl: st,stm32: Document interrupt-controller property
dt-bindings: pinctrl: st,stm32: Document gpio-hog pattern property
dt-bindings: pinctrl: st,stm32: Document gpio-line-names
pinctrl: st: stop abusing of_get_named_gpio()
pinctrl: wpcm450: Correct the fwnode_irq_get() return value check
pinctrl: bcm: Remove unused struct bcm6328_pingroup
pinctrl: qcom: restrict drivers per ARM/ARM64
pinctrl: bcm: ns: Remove redundant dev_err call
gpio: rockchip: request GPIO mux to pinctrl when setting direction
pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
pinctrl: cy8c95x0: Align function names in cy8c95x0_pmxops
pinctrl: cy8c95x0: Drop atomicity on operations on push_pull
pinctrl: cy8c95x0: Lock register accesses in cy8c95x0_set_mux()
pinctrl: sunxi: sun50i-h5: Switch to use dev_err_probe() helper
pinctrl: stm32: Switch to use dev_err_probe() helper
dt-bindings: qcom-pmic-gpio: Add PM7250B and PM8450 bindings
pinctrl: qcom: spmi-gpio: Add compatible for PM7250B
...
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
Add the SoC name to make it more clear. Also the next generation StarFive
SoCs will use "pinctrl-starfive" as the core of StarFive pinctrl driver.
No functional change.
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@linux.starfivetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220930061404.5418-1-hal.feng@linux.starfivetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the StarFive JH7100 pinctrl driver to a new subdirectory
in preparation for adding more StarFive pinctrl drivers. No
functional change.
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@linux.starfivetech.com>
Link: https://lore.kernel.org/r/20220930060819.5320-1-hal.feng@linux.starfivetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin descriptions for this chip only look like standard GPIO device tree
descriptions, while in fact they contain additional data (in excess of
number of cells specified in description of gpio controllers). They also
refer to only pins/gpios belonging to the driver and not to arbitrary
gpio in the system.
Because we want to stop exporting OF-specific handlers from gpiolib-of,
let's parse the pin reference ourself instead of trying to call
of_get_named_gpio().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/YzSsgoVoJn4+mSpv@google.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fwnode_irq_get() can return zero to indicate IRQ mapping errors.
Handle this case by skipping the interrupt resource.
Fixes: a1d1e0e3d8 ("pinctrl: nuvoton: Add driver for WPCM450")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20220927175509.15695-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 0e3db16300fb("pinctrl: bcm: Convert drivers to use struct pingroup
and PINCTRL_PINGROUP()"), no one use struct bcm6328_pingroup, so remove it.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220927133926.103943-1-yuancan@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point to allow selecting pin-controller drivers for Qualcomm
ARMv7 SoCs when building ARM64 kernel, and vice versa. This makes
kernel configuration more difficult as many do not remember the Qualcomm
SoCs. There won't be a single image for ARMv7 and ARMv8/9 SoCs, so no
features/options are lost.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220925112103.148836-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before the split of gpio and pinctrl sections in their own driver,
rockchip_set_mux was called in pinmux_ops.gpio_set_direction for
configuring a pin in its GPIO function.
This is essential for cases where pinctrl is "bypassed" by gpio
consumers otherwise the GPIO function is not configured for the pin and
it does not work. Such was the case for the sysfs/libgpiod userspace
GPIO handling.
Let's re-implement the pinmux_ops.gpio_set_direction callback so that
the gpio subsystem can request from the pinctrl driver to put the pin in
its GPIO function.
Fixes: 9ce9a02039 ("pinctrl/rockchip: drop the gpio related codes")
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220930132033.4003377-2-foss+kernel@0leil.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems that cy8c95x0_set_mux() missed serialization of IO access.
And its implementation looks half-baked. Add locking to the function.
Fixes: e6cbbe4294 ("pinctrl: Add Cypress cy8c95x0 support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220916205450.86278-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122208.1894769-1-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122015.1893880-1-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On PREEMPT_RT enabled kernels the demultiplex interrupt handler is force
threaded and runs with interrupts enabled. The invocation of
generic_handle_domain_irq() with interrupts enabled triggers a lockdep
warning due to a non-irq safe lock acquisition.
Instead of disabling interrupts on the driver level, use
generic_handle_domain_irq_safe().
[ tglx: Split out from combo patch ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/YnkfWFzvusFFktSt@linutronix.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215954
The SPMI based PMICs have the HIGH and LOW GPIO output strength mappings
interchanged, fix them.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220912210624.4527-3-quic_amelende@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for SPMI PMIC GPIO subtypes GPIO_LV_VIN2 and
GPIO_MV_VIN3.
GPIO_LV_VIN2 GPIOs support two input reference voltages: VIN0 and
VIN1. These are typically connected to 1.8 V and 1.2 V supplies
respectively.
GPIO_MV_VIN3 GPIOs support three input reference voltages: VIN0,
VIN1, and VIN2. These are typically connected to Vph, 1.8 V, and
1.2 V supplies respectively.
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220912210624.4527-2-quic_amelende@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b6d09f7807 ("pinctrl: nomadik: Drop U8540/9540 support") removes
the DB8540 pin controller driver and its config PINCTRL_DB8540.
There is some code left-over in the generic nomadik pinctrl driver, i.e.,
drivers/pinctrl/nomadik/pinctrl-nomadik.{ch}, that is still around for the
removed DB8540 pin controller driver.
Remove this remaining dead code.
This issue was discovered with ./scripts/checkkconfigsymbols.py.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220919065435.27747-1-lukas.bulwahn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the Nomadik GPIO irqchip immutable.
Tested on the Samsung Galaxy SIII mini GT-I8190.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220917203036.167607-2-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq data passed to irc_chip handlers i the struct gpio_chip
and nothing else. We are just lucky that the nomadik chip
pointer is first in the struct. Use the proper dereferencing
and helpers.
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220917203036.167607-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an external device generated a level based interrupt then the
interrupt controller could miss the interrupt. The reason is that the
interrupt controller can detect only link changes.
In the following example, if there is a PHY that generates an interrupt
then the following would happen. The GPIO detected that the interrupt
line changed, and then the 'ocelot_irq_handler' was called. Here it
detects which GPIO line saw the change and for that will call the
following:
1. irq_mask
2. phy interrupt routine
3. irq_eoi
4. irq_unmask
And this works fine for simple cases, but if the PHY generates many
interrupts, for example when doing PTP timestamping, then the following
could happen. Again the function 'ocelot_irq_handler' will be called
and then from here the following could happen:
1. irq_mask
2. phy interrupt routine
3. irq_eoi
4. irq_unmask
Right before step 3(irq_eoi), the PHY will generate another interrupt.
Now the interrupt controller will acknowledge the change in the
interrupt line. So we miss the interrupt.
A solution will be to use 'handle_level_irq' instead of
'handle_fasteoi_irq', because for this will change routine order of
handling the interrupt.
1. irq_mask
2. irq_ack
3. phy interrupt routine
4. irq_unmask
And now if the PHY will generate a new interrupt before irq_unmask, the
interrupt controller will detect this because it already acknowledge the
change in interrupt line at step 2(irq_ack).
But this is not the full solution because there is another issue. In
case there are 2 PHYs that share the interrupt line. For example phy1
generates an interrupt, then the following can happen:
1.irq_mask
2.irq_ack
3.phy0 interrupt routine
4.phy1 interrupt routine
5.irq_unmask
In case phy0 will generate an interrupt while clearing the interrupt
source in phy1, then the interrupt line will be kept down by phy0. So
the interrupt controller will not see any changes in the interrupt line.
The solution here is to update 'irq_unmask' such that it can detect if
the interrupt line is still active or not. And if it is active then call
again the procedure to clear the interrupts. But we don't want to do it
every time, only if we know that the interrupt controller has not seen
already that the interrupt line has changed.
While at this, add support also for IRQ_TYPE_LEVEL_LOW.
Fixes: be36abb71d ("pinctrl: ocelot: add support for interrupt controller")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220909145942.844102-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1. Minor fix in order of initializing pinctrl driver - GPIOs should be
configured before registering gpiolib.
2. Final steps to deprecated bindings headers with register constants.
The constants were moved to include files in DTS directories, because
these are not suitable for bindings. Remove final references and
mark binding header as deprecated to warn any users.
-----BEGIN PGP SIGNATURE-----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=YIgT
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v6.1
1. Minor fix in order of initializing pinctrl driver - GPIOs should be
configured before registering gpiolib.
2. Final steps to deprecated bindings headers with register constants.
The constants were moved to include files in DTS directories, because
these are not suitable for bindings. Remove final references and
mark binding header as deprecated to warn any users.
There are a few Ocelot chips that can contain SGPIO logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.
Add support for these non-memory-mapped configurations.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-6-colin.foster@in-advantage.com
As the commit message suggests, this simply adds the ability to select
SGPIO pinctrl as a module. This becomes more practical when the SGPIO
hardware exists on an external chip, controlled indirectly by I2C or SPI.
This commit enables that level of control.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-5-colin.foster@in-advantage.com
There are a few Ocelot chips that contain pinctrl logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513 and 7514. In
the externally controlled configurations these registers are not
memory-mapped.
Add support for these non-memory-mapped configurations.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-4-colin.foster@in-advantage.com
fwnode_irq_get() may return all possible signed values, such as Linux
error code or 0. Fix the code to handle this properly.
Fixes: 1074e1d23a ("pinctrl: pistachio: Switch to use fwnode instead of")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908094323.31965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irqchip implementation used inside the gpiochips are not supposed to
be changed during runtime. So let's make the one inside the spmi-gpio
gpiochip immutable.
This fixes the below warning during boot:
gpio gpiochip0: (c440000.spmi:pmic@0:gpio@c000): not an immutable chip, please consider fixing it!
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220830092232.168561-1-manivannan.sadhasivam@linaro.org
[switched two lines as indicated by Johan]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220905180034.73132-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fwnode_irq_get() may return all possible signed values, such as Linux
error code. Fix the code to handle this properly.
Fixes: be2dc859ab ("pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220906115021.8661-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PINCTRL_IMX depends on OF, however the dependency is missed when selected
by PINCTRL_IMX8M* (it does not follow the indirect 'select' statements),
select it explicitly.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202209050605.fezJUgFH-lkp@intel.com/
Fixes: 87c2a29a6b ("pinctrl: imx8m: kconfig: Depends on SOC_IMX8M")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Link: https://lore.kernel.org/r/20220905224408.346425-1-francesco.dolcini@toradex.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In a few comments the style is not aligned with the rest.
Correct them.
While at it, drop unneeded blank lines and deduplicate 'Author'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-17-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of the GENMASK() (far less error-prone, far more concise).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-16-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPI table on Intel Galileo Gen 1 has wrong pin number for IRQ resource
of the I²C GPIO expander. Since we know what that number is and luckily
have GPIO bases fixed for SoC's controllers, we may use a simple DMI quirk
to match the platform and retrieve GpioInt() pin on it for the expander in
question.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support of the expander found on Intel Galileo Gen1 board.
The platform information comes from ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-14-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The introduced callback ->pin_dbg_show() is useful for debugging.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the default values to the 'default' case in the switches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have pin configuration getter and setter provided,
there is no need to duplicate that in the custom ->set_config().
Instead, switch to gpiochip_generic_config().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control framework checks pin boundaries before calling
the respective driver's callbacks. Hence no need to check for
pin boundaries, the respective conditionals won't be ever true.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cypress CY8C95x0 chips have an internal EEPROM that defines
initial configuration. It might be that bootloader or other
entity wrote the platform related setup into it. Don't override
it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since it's a pin control, GPIO counterpart needs to know the mapping
between pin numbering and GPIO numbering. Enable this by calling
gpiochip_add_pin_range() at the chip addition time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The npins field is assigned twice. Remove the first occurrence.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cypress GPIO expander is an I²C discrete component. Hence
the platform may contain more than one of a such. Currently
this has limitations in the driver due to same name used for
all chips of a type. Replace this with device instance specific
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's an obvious typo in never tested piece of code that
successful detection shouldn't fail. Fix that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No need to assign first line number for IRQ chip.
Let IRQ core to decide.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use dev_dbg() instead of printk(KERN_DEBUG) to avoid the following
checkpatch.pl warning:
"Prefer [subsystem eg: netdev]_dbg([subsystem]dev, ... then
dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-4-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio suspend/resume execution local to driver and let it execute as
close as possible to the moment the machine specific PM code is executed
(by setting it to .noirq member of dev_pm_ops). With this the
at91_pinctrl_gpio_suspend()/at91_pinctrl_gpio_resume() calls were removed
from arch/arm/mach-at91/pm.c and also a header has been removed.
The patch has been checked on sama5d3_xplained, sam9x60ek,
sama5d2_xplained, sama7g5ek boards.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-3-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change PINCTRL_IMX8M* dependency from just ARCH_MXC to SOC_IMX8M,
likewise is done for other PINCTRL_IMX* kconfig. This avoid polluting
the config when SOC_IMX8M is not enabled.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220830142727.313080-1-francesco.dolcini@toradex.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the driver want to disable the signal of the function, it doesn't
need to query the state of the mux function's signal on a pin. The
condition below will miss the disable of the signal:
Ball | Default | P0 Signal | P0 Expression | Other
-----+---------+-----------+-----------------------------+----------
E21 GPIOG0 SD2CLK SCU4B4[16]=1 & SCU450[1]=1 GPIOG0
-----+---------+-----------+-----------------------------+----------
B22 GPIOG1 SD2CMD SCU4B4[17]=1 & SCU450[1]=1 GPIOG1
-----+---------+-----------+-----------------------------+----------
Assume the register status like below:
SCU4B4[16] == 1 & SCU4B4[17] == 1 & SCU450[1]==1
After the driver set the Ball E21 to the GPIOG0:
SCU4B4[16] == 0 & SCU4B4[17] == 1 & SCU450[1]==0
When the driver want to set the Ball B22 to the GPIOG1, the condition of
the SD2CMD will be false causing SCU4B4[17] not to be cleared.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20220818101839.28860-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Feedback from Kent had showed some better selections for symbols to
use for pinctrl-amd debugfs output. Adopt some of those instead.
Fixes: e8129a076a ("pinctrl: amd: Use unicode for debugfs output")
Suggested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220823230753.14799-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name of A100 R_PIO driver should be sun50i-a100-r-pinctrl,
not sun50iw10p1-r-pinctrl.
Fixes: 473436e764 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220819024541.74191-1-michael@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver support for MediaTek SoC mt8188.
Signed-off-by: Hui.Liu <hui.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220818075012.20880-3-hui.liu@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SC8280XP.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[189 - 207] --> LPASS LPI GPIO [0 - 18]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113747.9111-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8450.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113833.9625-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220621112904.65674-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620165053.74170-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for cypress I2C GPIO expanders cy8c9520, cy8c9540 and
cy8c9560. The GPIO expanders feature a PWM mode, thus add it as
pinctrl driver.
The chip features multiple drive modes for each pin when configured
as output and multiple bias settings when configured as input.
Tested all three components and verified that all functionality
is fully working.
Datasheet: https://www.cypress.com/file/37971/download
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Link: https://lore.kernel.org/r/20220816054917.7893-3-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin numbers for UFS_RESET and SDC2_* are not
consistent in the pinctrl driver for sc8180x.
So fix it.
Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec ("pinctrl: qcom: Add sc8180x TLMM driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-3-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently in the wakeirq_map, gpio36 and gpio37 have the same wakeirq
number, resulting in gpio37 being unable to trigger interrupts.
It looks like that this is a typo in the wakeirq map. So fix it.
Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec ("pinctrl: qcom: Add sc8180x TLMM driver")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-2-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now when all MPP pins are properly defined and every MPP pin has GPIO
function, always checks for errors in armada_37xx_gpio_request_enable()
function when calling armada_37xx_pmx_set_by_name(). Function
armada_37xx_pmx_set_by_name() should not return "not supported" error
anymore for any GPIO pin when requesting GPIO mode.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220805122202.23174-3-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All 3 MPP pins (20, 21 and 22) can be configured individually and also can
be configured to GPIO functions. Fix definitions for these MPP pins in
existing pin groups. After this change GPIO function can be enabled just
for one of these 3 pins.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-2-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio1_5 and gpio2_2 are GPIO-only pins. Add them into MPP groups table
so they are properly exported as valid pin numbers.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-1-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RV1126 has five GPIOs groups - GPIO0 in PD_MMU and GPIO1-4
in PD_BUS.
In GPIO0, up to Lower C group GPIO0_C[3:0] is part of PMU
but rest of the groups from there are part of GRF.
Added pinctrl support for RV1126 and the pull, drv and schmitt
calculations are inferred from [1] authored by Jianqun Xu.
[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/pinctrl/pinctrl-rockchip.c
Cc: linux-gpio@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20220818124132.125304-8-jagan@edgeble.ai
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As soon as a gpio is registered, it should be usable by a consumer. So,
do all the initialization before registering the gpios. Without this
change, a consumer can request a GPIO IRQ and have the gpio to IRQ
mapping fail.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220727013349.3056826-1-saravanak@google.com
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin
bias, then fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO.
-----BEGIN PGP SIGNATURE-----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=enmk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Outside the pinctrl driver and DT bindings we hit some Arm DT files,
patched by the maintainers.
Other than that it is business as usual.
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin bias, then
fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"
* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
pinctrl: qcom: sm8250: Fix PDC map
pinctrl: amd: Fix an unused variable
dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
dt-bindings: pinctrl: mt8186: Add gpio-line-names property
ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
pinctrl: amd: Use unicode for debugfs output
pinctrl: amd: Fix newline declaration in debugfs output
pinctrl: at91: Fix typo 'the the' in comment
dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
pinctrl: mvebu: Missing a blank line after declarations.
pinctrl: qcom: Add SM6375 TLMM driver
dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
pinctrl: imx93: Add MODULE_DEVICE_TABLE()
pinctrl: sunxi: Add driver for Allwinner D1
pinctrl: sunxi: Make some layout parameters dynamic
pinctrl: sunxi: Refactor register/offset calculation
...
Highlights:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop Studio
- thinkpad_acpi: AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Fix acpi_video_handles_brightness_key_presses()
- video: Change how we determine if brightness key-presses are handled
Documentation/ABI:
- Add new attributes for mlxreg-io sysfs interfaces
- mlxreg-io: Fix contact info
Drop the PMC_ATOM Kconfig option:
- Drop the PMC_ATOM Kconfig option
EDAC, pnd2:
- convert to use common P2SB accessor
- Use proper I/O accessors and address space annotation
HID:
- surface-hid: Add support for hot-removal
ISST:
- PUNIT device mapping with Sub-NUMA clustering
Kconfig:
- Remove unnecessary "if X86"
MAINTAINERS:
- repair file entry in MICROSOFT SURFACE AGGREGATOR TABLET-MODE SWITCH
Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans:
- Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans
Move AMD platform drivers to separate directory:
- Move AMD platform drivers to separate directory
acer-wmi:
- Use backlight helper
acer_wmi:
- Cleanup Kconfig selects
apple-gmux:
- Use backlight helper
asus-wmi:
- Add mic-mute LED classdev support
- Add key mappings
compal-laptop:
- Use backlight helper
efi:
- Fix efi_power_off() not being run before acpi_power_off() when necessary
gigabyte-wmi:
- add support for B660I AORUS PRO DDR4
hp-wmi:
- Ignore Sanitization Mode event
i2c:
- i801: convert to use common P2SB accessor
ideapad-laptop:
- Add Ideapad 5 15ITL05 to ideapad_dytc_v4_allow_table[]
- Add allow_v4_dytc module parameter
intel/pmc:
- Add Alder Lake N support to PMC core driver
intel_atomisp2_led:
- Also turn off the always-on camera LED on the Asus T100TAF
leds:
- simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
- simatic-ipc-leds: Convert to use P2SB accessor
mfd:
- lpc_ich: Add support for pinctrl in non-ACPI system
- lpc_ich: Switch to generic p2sb_bar()
- lpc_ich: Factor out lpc_ich_enable_spi_write()
mlx-platform:
- Add COME board revision register
- Add support for new system XH3000
- Introduce support for COMe NVSwitch management module for Vulcan chassis
- Add support for systems equipped with two ASICs
- Add cosmetic changes for alignment
- Make activation of some drivers conditional
p2sb:
- Move out of X86_PLATFORM_DEVICES dependency
panasonic-laptop:
- Use acpi_video_get_backlight_type()
- filter out duplicate volume up/down/mute keypresses
- don't report duplicate brightness key-presses
- revert "Resolve hotkey double trigger bug"
- sort includes alphabetically
- de-obfuscate button codes
pinctrl:
- intel: Check against matching data instead of ACPI companion
platform/mellanox:
- mlxreg-lc: Fix error flow and extend verbosity
- mlxreg-io: Add locking for io operations
- nvsw-sn2201: fix error code in nvsw_sn2201_create_static_devices()
platform/olpc:
- Fix uninitialized data in debugfs write
platform/surface:
- gpe: Add support for 13" Intel version of Surface Laptop 4
- tabletsw: Fix __le32 integer access
- Update copyright year of various drivers
- aggregator: Move subsystem hub drivers to their own module
- aggregator: Move device registry helper functions to core module
- aggregator_registry: Add support for tablet mode switch on Surface Laptop Studio
- aggregator_registry: Add support for tablet mode switch on Surface Pro 8
- Add KIP/POS tablet-mode switch driver
- aggregator: Add helper macros for requests with argument and return value
- aggregator: Reserve more event- and target-categories
- avoid flush_scheduled_work() usage
- aggregator_registry: Add support for keyboard cover on Surface Pro 8
- aggregator_registry: Add KIP device hub
- aggregator_registry: Change device ID for base hub
- aggregator_registry: Generify subsystem hub functionality
- aggregator: Add comment for KIP subsystem category
- aggregator_registry: Use client device wrappers for notifier registration
- aggregator: Allow notifiers to avoid communication on unregistering
- aggregator: Allow devices to be marked as hot-removed
- aggregator: Allow is_ssam_device() to be used when CONFIG_SURFACE_AGGREGATOR_BUS is disabled
platform/x86/amd/pmc:
- Add new platform support
- Add new acpi id for PMC controller
platform/x86/dell:
- Kconfig: Remove unnecessary "depends on X86_PLATFORM_DEVICES"
platform/x86/intel:
- Add Primary to Sideband (P2SB) bridge support
platform/x86/intel/ifs:
- Mark as BROKEN
platform/x86/intel/pmt:
- telemetry: Fix fixed region handling
platform/x86/intel/vsec:
- Fix wrong type for local status variables
- Add PCI error recovery support to Intel PMT
- Add support for Raptor Lake
- Rework early hardware code
pmc_atom:
- Fix comment typo
- Match all Lex BayTrail boards with critclk_systems DMI table
power/supply:
- surface_battery: Use client device wrappers for notifier registration
- surface_charger: Use client device wrappers for notifier registration
serial-multi-instantiate:
- Sort ACPI IDs by HID
- Get rid of redundant 'else'
- Use while (i--) pattern to clean up
- Improve dev_err_probe() messaging
- Drop duplicate check
- Improve autodetection
simatic-ipc:
- drop custom P2SB bar code
sony-laptop:
- Remove useless comparisons in sony_pic_read_possible_resource()
system76_acpi:
- Use dev_get_drvdata
thinkpad_acpi:
- Enable AMT by default on supported systems
- Add support for hotkey 0x131a
- Add support for automatic mode transitions
- profile capabilities as integer
- do not use PSC mode on Intel platforms
- Fix a memory leak of EFCH MMIO resource
- Replace custom str_on_off() etc
- Sort headers for better maintenance
- Use backlight helper
tools/power/x86/intel-speed-select:
- Remove unneeded semicolon
- Fix off by one check
watchdog:
- simatic-ipc-wdt: convert to use P2SB accessor
x86-android-tablets:
- Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmLrndEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zeMgf7BjSCz6ZA8SSY1i8QHDTvdjySihHJ
j07Gn3j1T/5G00R/r6viMDE4PxcYvMAPXjq3azepKQd8H5kGfE323SA6fgWFPAvi
P2OvEfvWfI5S8FYGYPBkNP2MjQ5MFe7qzLEh3+wQH0ocJ7WRCi457B4Xvtd2gWI3
dHj5gMSWC3O5xNa2S4Mg3dnD9uJlwhX+FNjWIuRy8eh5+DikgByyC4B+uW6WtO5e
t0rmIm6q5wUzB7dIetJLoAQwrcpYAOkK7L33G9h/7knWAfiJfklaKTbftnoxbDSv
iGWODkLDyob4C48DmVusS6WMEhPUzl/R33+tk6LjVt/YOYOP030EMtCECQ==
=Krhc
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop
Studio
- thinkpad_acpi:
- AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
platform/x86/intel/vsec: Fix wrong type for local status variables
platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
platform/x86: pmc_atom: Fix comment typo
platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
platform/olpc: Fix uninitialized data in debugfs write
platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
tools/power/x86/intel-speed-select: Remove unneeded semicolon
tools/power/x86/intel-speed-select: Fix off by one check
platform/surface: tabletsw: Fix __le32 integer access
Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
Documentation/ABI: mlxreg-io: Fix contact info
platform/mellanox: mlxreg-io: Add locking for io operations
platform/x86: mlx-platform: Add COME board revision register
platform/x86: mlx-platform: Add support for new system XH3000
platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
platform/x86: mlx-platform: Add support for systems equipped with two ASICs
platform/x86: mlx-platform: Add cosmetic changes for alignment
platform/x86: mlx-platform: Make activation of some drivers conditional
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Here is the set of driver core and kernfs changes for 6.0-rc1.
"biggest" thing in here is some scalability improvements for kernfs for
large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed
and discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYuqCnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym/JgCcCnaycJY00ZPRQm3LQCyzfJ0HgqoAn2qxGV+K
NKycLeXZSnuvIA87dycE
=/4Jk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / kernfs updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.0-rc1.
The "biggest" thing in here is some scalability improvements for
kernfs for large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed and
discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (63 commits)
docs: embargoed-hardware-issues: fix invalid AMD contact email
firmware_loader: Replace kmap() with kmap_local_page()
sysfs docs: ABI: Fix typo in comment
kobject: fix Kconfig.debug "its" grammar
kernfs: Fix typo 'the the' in comment
docs: driver-api: firmware: add driver firmware guidelines. (v3)
arch_topology: Fix cache attributes detection in the CPU hotplug path
ACPI: PPTT: Leave the table mapped for the runtime usage
cacheinfo: Use atomic allocation for percpu cache attributes
drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist
MAINTAINERS: Change mentions of mpm to olivia
docs: ABI: sysfs-devices-soc: Update Lee Jones' email address
docs: ABI: sysfs-class-pwm: Update Lee Jones' email address
Documentation/process: Add embargoed HW contact for LLVM
Revert "kernfs: Change kernfs_notify_list to llist."
ACPI: Remove the unused find_acpi_cpu_cache_topology()
arch_topology: Warn that topology for nested clusters is not supported
arch_topology: Add support for parsing sockets in /cpu-map
arch_topology: Set cluster identifier in each core/thread from /cpu-map
arch_topology: Limit span of cpu_clustergroup_mask()
...
All the many other configs depend on config PINCTRL_MSM, yet for config
PINCTRL_SM8450 we select config PINCTRL_MSM. Make config PINCTRL_SM8450
depend on PINCTRL_MSM to be consistent with the rest.
Signed-off-by: John Garry <john.garry@huawei.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/1658829764-124936-1-git-send-email-john.garry@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
`char *output_enable` is no longer used once switching to unicode
output.
Fixes: e8129a076a ("pinctrl: amd: Use unicode for debugfs output")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220801144952.141-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
core:
- Fix a few inconsistencies between UP and SMP vs. interrupt affinities
- Small updates and cleanups all over the place
drivers:
- New driver for the LoongArch interrupt controller
- New driver for the Renesas RZ/G2L interrupt controller
- Hotpath optimization for SiFive PLIC
- Workaround for broken PLIC edge triggered interrupts
- Simall cleanups and improvements as usual
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmLn5agTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoV2HD/4u0+09Fd8Awt1Knnb4CInmwFihZ/bu
EiS1Air+MEJ/fyFb5sT/Dn8YdUWYA6a3ifpLMGBwrKCcb5pMwPEtI8uqjSmtgsN/
2Z4o3N5v6EgM25CtrHNBrXK0E9Rz5Py49gm5p3K7+h4g63z9JwrM4G0Bvr8+krLS
EV9IZU6kVmGC6gnG/MspkArsLk1rCM0PU0SJ2lEPsWd1fjhVSDfunvy/qnnzXRzz
wjrcAf+a2Kgb1TMnpL6tx9d2Xx8KrKfODZTdOmPHrdv58F0EbJzapJnAVkYZDPtR
LE2kQc2Qhdawx0kgNNNhvu9P6oZtpnK9N7KAhDQdw17sgrRygINjAMSEe2RykYL1
lK+lJOIzfyd2JkEuC/8w1ZezL88S0EaTNawrkxjJ8L3fa7WDbwilCC+1w95QydCv
sQB137OaLKgWetcRsht9PLWFb4ujkWzxoPf2cPPsm81EzCicNtBuNPLReBTcNrWJ
X2VPpbaqRK8t8bnkXRqhahbq7f8c86feoICHfA4c7T4eZUp/Oq6T8aNvf6WPgjae
I2/FO6kxZj3CQqFkhJGhiZRtGZdx6HLCsL84A+2Ktsra+D8+/qecZCnkHYtz0Vo6
aFuGg+Wj+zuc2QfdaWwG8Dh5dijbxgHGHhzbh9znsWzytN9gfoBxuvBejf65i6sC
In63mEkv35ttfA==
=OnhF
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2022-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for interrupt core and drivers:
Core:
- Fix a few inconsistencies between UP and SMP vs interrupt
affinities
- Small updates and cleanups all over the place
New drivers:
- LoongArch interrupt controller
- Renesas RZ/G2L interrupt controller
Updates:
- Hotpath optimization for SiFive PLIC
- Workaround for broken PLIC edge triggered interrupts
- Simall cleanups and improvements as usual"
* tag 'irq-core-2022-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
irqchip/mmp: Declare init functions in common header file
irqchip/mips-gic: Check the return value of ioremap() in gic_of_init()
genirq: Use for_each_action_of_desc in actions_show()
irqchip / ACPI: Introduce ACPI_IRQ_MODEL_LPIC for LoongArch
irqchip: Add LoongArch CPU interrupt controller support
irqchip: Add Loongson Extended I/O interrupt controller support
irqchip/loongson-liointc: Add ACPI init support
irqchip/loongson-pch-msi: Add ACPI init support
irqchip/loongson-pch-pic: Add ACPI init support
irqchip: Add Loongson PCH LPC controller support
LoongArch: Prepare to support multiple pch-pic and pch-msi irqdomain
LoongArch: Use ACPI_GENERIC_GSI for gsi handling
genirq/generic_chip: Export irq_unmap_generic_chip
ACPI: irq: Allow acpi_gsi_to_irq() to have an arch-specific fallback
APCI: irq: Add support for multiple GSI domains
LoongArch: Provisionally add ACPICA data structures
irqdomain: Use hwirq_max instead of revmap_size for NOMAP domains
irqdomain: Report irq number for NOMAP domains
irqchip/gic-v3: Fix comment typo
dt-bindings: interrupt-controller: renesas,rzg2l-irqc: Document RZ/V2L SoC
...
The output is currently split across two lines making it more
difficult to parse unless the newlines are removed between pins
or it's read in by a parser like Libreoffice Calc or Google docs.
To make it easier to follow to the naked eye in a terminal window:
* drop the newline in the middle of pin definitions
* shorten all output using unicode characters
* align all pipe delimitters
* output the same phrase even for disabled functions
(but with a ∅ character)
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220722220810.28894-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the debugfs output for pinctrl-amd puts the first line
combined with "GPIO bank". This makes it a little harder to process
as the file needs to be manually corrected for the mistake.
Change this to be a new line character instead.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220722220810.28894-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver to control the TLMM block on SM6375. This is an adapted
version of msm-5.4's pinctrl-blair driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20220716192900.454653-2-konrad.dybcio@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* irq/misc-5.20:
: .
: Misc IRQ changes for 5.20:
:
: - Let irq_set_chip_handler_name_locked() take a const struct irq_chip *
:
: - Convert the ocelot irq_chip to being immutable (depends on the above)
:
: - Tidy-up the NOMAP irqdomain API variant
:
: - Teach action_show() to use for_each_action_of_desc()
:
: - Check ioremap() return value in the MIPS GIC driver
:
: - Move MMP driver init function declarations into the common .h
:
: - The obligatory typo fixes
: .
irqchip/mmp: Declare init functions in common header file
irqchip/mips-gic: Check the return value of ioremap() in gic_of_init()
genirq: Use for_each_action_of_desc in actions_show()
irqdomain: Use hwirq_max instead of revmap_size for NOMAP domains
irqdomain: Report irq number for NOMAP domains
irqchip/gic-v3: Fix comment typo
pinctrl: ocelot: Make irq_chip immutable
genirq: Allow irq_set_chip_handler_name_locked() to take a const irq_chip
Signed-off-by: Marc Zyngier <maz@kernel.org>
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The armada-37xx implementation, armada_37xx_irq_set_type(), uses an MMIO
regmap created by of_syscon_register(), which uses plain spinlocks
(the kind that are sleepable on RT).
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Make this driver create its own MMIO regmap, with use_raw_spinlock=true,
and stop relying on syscon to provide it.
This patch depends on commit 67021f25d9 ("regmap: teach regmap to use
raw spinlocks if requested in the config").
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 2f22760539 ("pinctrl: armada-37xx: Add irqchip support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220716233745.1704677-3-vladimir.oltean@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The armada-37xx implementation, armada_37xx_irq_set_type(), takes a
plain spinlock, the kind that becomes sleepable on RT.
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Replace the driver's irq_lock with a raw spinlock, to disable preemption
even on RT.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 2f22760539 ("pinctrl: armada-37xx: Add irqchip support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220716233745.1704677-2-vladimir.oltean@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It was observed that by allowing pinctrl_amd to be loaded
later in the boot process that interrupts sent to the GPIO
controller early in the boot are not serviced. The kernel treats
these as a spurious IRQ and disables the IRQ.
This problem was exacerbated because it happened on a system with
an encrypted partition so the kernel object was not accesssible for
an extended period of time while waiting for a passphrase.
To avoid this situation from occurring, stop allowing pinctrl-amd
from being built as a module and instead require it to be built-in
or disabled.
Reported-by: madcatx@atlas.cz
Suggested-by: jwrdegoede@fedoraproject.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216230
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220713175950.964-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pass MODULE_DEVICE_TABLE() so that module autoloading can work.
This also aligns with the other i.MX8 pinctrl drivers.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Link: https://lore.kernel.org/r/20220712115154.2348971-1-festevam@denx.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This SoC contains a pinctrl with a new register layout. Use the variant
parameter to set the right register offsets. This pinctrl also increases
the number of functions per pin from 8 to 16, taking advantage of all 4
bits in the mux config field (so far, only functions 0-8 and 14-15 are
used). This increases the maximum possible number of functions.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20220713025233.27248-7-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Starting with the D1/D1s/T113 SoC, Allwinner changed the layout of the
pinctrl registers. This new layout widens the drive level field, which
affects the pull register offset and the overall bank size.
In order to support multiple register layouts, some of the layout
parameters need to be set based on the pinctrl variant. This requires
passing the pinctrl struct pointer to the register/offset calculation
functions.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-6-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Starting with the D1/D1s/T113 SoC, Allwinner changed the layout of the
pinctrl registers. This new layout widens the drive level field, which
affects the pull register offset and the overall bank size.
As a first step to support this, combine the register and offset
calculation functions, and refactor the math to depend on one constant
for field widths instead of three. This minimizes the code size impact
of making some of the factors dynamic.
While rewriting these functions, move them to the implementation file,
since that is the only file where they are used. And make the comment
more generic, without mentioning specific offsets/sizes.
The callers are updated to expect a shifted mask, and to use consistent
terminology (reg/shift/mask/val).
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-5-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H616 and newer SoCs feature a 2.5V I/O bias mode in addition to the
1.8V and 3.3V modes. This mode is entered by selecting the 3.3V level
and disabling the "withstand function".
H616 supports this capability on its main PIO only. A100 supports this
capability on both its PIO and R-PIO.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-4-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 requires I/O bias configuration on both of its PIO devices.
Previously it was only done for the main PIO.
The setting for Port L is at bit 0, so the bank calculation needs to
account for the pin base. Otherwise the wrong bit is used.
Fixes: cc62383fce ("pinctrl: sunxi: Support I/O bias voltage setting on H6")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-3-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blamed commit changed to use regmaps instead of __iomem. But it
didn't update the register offsets to be at word offset, so it uses byte
offset.
Another issue with the same commit is that it has a limit of 32 registers
which is incorrect. The sparx5 has 64 while lan966x has 77.
Fixes: 076d9e71bc ("pinctrl: ocelot: convert pinctrl to regmap")
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220713193750.4079621-3-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blamed commit introduce support for lan966x which use the same
pinconf_ops as sparx5. The problem is that pinconf_ops is specific to
sparx5. More precisely the offset of the bits in the pincfg register are
different and also lan966x doesn't have support for
PIN_CONFIG_INPUT_SCHMITT_ENABLE.
Fix this by making pinconf_ops more generic such that it can be also
used by lan966x. This is done by introducing 'ocelot_pincfg_data' which
contains the offset and what is supported for each SOC.
Fixes: 531d6ab365 ("pinctrl: ocelot: Extend support for lan966x")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220713193750.4079621-2-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since recently, the kernel is nagging about mutable irq_chips:
[ 2.593426] gpio gpiochip0: (ocelot-gpio): not an immutable chip, please consider fixing it!
Make it const, flag it as IRQCHIP_IMMUTABLE, add the new helper
functions and call the appropriate gpiolib functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220706151553.1580790-2-michael@walle.cc
In some cases we may get a platform device that has ACPI companion
which is different to the pin control described in the ACPI tables.
This is primarily happens when device is instantiated by board file.
In order to allow this device being enumerated, refactor
intel_pinctrl_get_soc_data() to check the matching data instead of
ACPI companion.
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
As the potential failure of the kcalloc(),
it should be better to check it in order to
avoid the dereference of the NULL pointer.
Fixes: aa74c44be1 ("pinctrl: Add driver for Sunplus SP7021")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Link: https://lore.kernel.org/r/20220710154822.2610801-1-williamsukatube@163.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because of the possible failure of the allocation, data->domains might
be NULL pointer and will cause the dereference of the NULL pointer
later.
Therefore, it might be better to check it and directly return -ENOMEM
without releasing data manually if fails, because the comment of the
devm_kmalloc() says "Memory allocated with this function is
automatically freed on driver detach.".
Fixes: a86854d0c5 ("treewide: devm_kzalloc() -> devm_kcalloc()")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Link: https://lore.kernel.org/r/20220710154922.2610876-1-williamsukatube@163.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl dt_node_to_map method may be called in parallel which leads
us to call pinconf_generic_add_group and pinconf_generic_add_function
in parallel. This is not supported though and leads to errors, so add a
mutex to serialize these calls.
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20220627085333.1774396-1-emil.renner.berthing@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add IRQ domain to RZ/G2L pinctrl driver to handle GPIO interrupt.
GPIO0-GPIO122 pins can be used as IRQ lines but only 32 pins can be
used as IRQ lines at a given time. Selection of pins as IRQ lines
is handled by IA55 (which is the IRQC block) which sits in between the
GPIO and GIC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220707182314.66610-7-prabhakar.mahadev-lad.rj@bp.renesas.com
The gpiolib is unique in the way it uses intermediate fwspecs
when feeding an interrupt specifier to the parent domain, as it
relies on the populate_parent_alloc_arg() callback to perform
a dynamic allocation.
This is pretty inefficient (we free the structure almost immediately),
and the only reason this isn't a stack allocation is that our
ThunderX friend uses MSIs rather than a FW-constructed structure.
Let's solve it by providing a new type composed of the union
of a struct irq_fwspec and a msi_info_t, which satisfies both
requirements. This allows us to use a stack allocation, and we
can move the handful of users to this new scheme.
Also perform some additional cleanup, such as getting rid of the
stub versions of the irq_domain_translate_*cell helpers, which
are never used when CONFIG_IRQ_DOMAIN_HIERARCHY isn't selected.
Tested on a Tegra186.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Daniel Palmer <daniel@thingy.jp>
Cc: Romain Perier <romain.perier@gmail.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220707182314.66610-2-prabhakar.mahadev-lad.rj@bp.renesas.com
- Add support for the RZ/V2M and R-Car V4H SoCs,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYsf0YAAKCRCKwlD9ZEnx
cNBbAP48c3HrPanpixUyw1W6c+kJ69/2jb1DFWFOOTXganjmmAD/YlnxcMyXnXTd
Lg59myS2XuSKaR8bSITCxpi3ou7fZAQ=
=uVgK
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.20 (take two)
- Add support for the RZ/V2M and R-Car V4H SoCs,
- Miscellaneous fixes and improvements.
Saving/restoring interrupt and wake status bits across suspend can
cause the suspend to fail if an IRQ is serviced across the
suspend cycle.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Fixes: 79d2c8bede ("pinctrl/amd: save pin registers over suspend/resume")
Link: https://lore.kernel.org/r/20220613064127.220416-3-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Update MAINTAINERS to set the Intel pin control status to Supported
* Switch Intel pin control drivers to use struct pingroup
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to to embedded struct pingroup
cherryview:
- Switch to to embedded struct pingroup
intel:
- Add Intel Meteor Lake pin controller support
- Drop no more used members of struct intel_pingroup
- Switch to to embedded struct pingroup
- Embed struct pingroup into struct intel_pingroup
lynxpoint:
- Switch to to embedded struct pingroup
MAINTAINERS:
- Update Intel pin control to Supported
Merge branch 'ib-v5.20-amd-pinctrl':
- Merge branch 'ib-v5.20-amd-pinctrl'
merrifield:
- Switch to to embedded struct pingroup
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSu93Raj3rZDNXzGZv7cr9lmVa5zAUCYsiWNwAKCRD7cr9lmVa5
zMoGAQDMB1dDqEbeEirmRy1/JKYjT0eV3BNxNhE2+jXOa22hMgEA/jTOhJvWblHI
F7G1epH2hyvF/Z/+10UmmI4RDKd0Eg0=
=Qzxi
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.20-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.20-1
* Update MAINTAINERS to set the Intel pin control status to Supported
* Switch Intel pin control drivers to use struct pingroup
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to to embedded struct pingroup
cherryview:
- Switch to to embedded struct pingroup
intel:
- Add Intel Meteor Lake pin controller support
- Drop no more used members of struct intel_pingroup
- Switch to to embedded struct pingroup
- Embed struct pingroup into struct intel_pingroup
lynxpoint:
- Switch to to embedded struct pingroup
MAINTAINERS:
- Update Intel pin control to Supported
Merge branch 'ib-v5.20-amd-pinctrl':
- Merge branch 'ib-v5.20-amd-pinctrl'
merrifield:
- Switch to to embedded struct pingroup
Commit 6c846d026d ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchips.
Following this change the following warning is now observed for the SPMI
PMIC pinctrl driver:
gpio gpiochip1: (200f000.spmi:pmic@0:gpio@c000): not an immutable chip, please consider fixing it!
Fix this by making the irqchip in the SPMI PMIC pinctrl driver immutable.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220624195112.894916-1-robimarko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds missing ERROROUTC_A settings.
Current existing ERROROUTC should be _B, this patch tidies it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtdtsj8m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V4H has PWM/PWM_A/PWM_B, but current PFC setting is mixed.
This patch adds missing PWM settings, and tidies these up.
According to Document, GP3_14 Function4 is PWM2_A,
but we can't select it at P1SR3[27:24].
This patch just ignore it for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7y9sj90.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds missing FlexRay pins.
Because Document (Rev.0.51) has 2x FXR_TXENA/B pin with no suffix (_A, _B),
this patch names them as _X.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmipsj9a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds missing SCIF1_X.
Because Document (Rev.0.51) has 2x SCIF1 with no suffix (_A, _B),
this patch names it as _X.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tu81sja1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V4H has SCIF3 and SCIF3_A, but current PFC setting is mixed.
This patch cleans up SCIF3/SCIF3_A, based on Rev.0.51.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8shsja7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds missing HSCIF1.
Because Document (Rev.0.51) has 2x HSCIF1 with no suffix (_A, _B),
this patch names it as _X.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wncxsjah.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Douglas Anderson