The firmware SMPS request should only be honoured if the
connection is currently with HE and on 160 MHz, so check
that and then potentially reapply any request if the BW
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.0cdcac5660da.I9ee7956fd4f48399855d1f97728bc58b36caf112@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When installing a (new) key, set the replay counter so that
after FW restart the firmware has the correct value of the
replay counters.
This doesn't have a large effect - for frames that reach
the driver, it will do a replay check, and when installing
a new key, the counter is normally zero to start with (not
for GTK though, if joining the BSS for the first time).
Since this only affects frames handled entirely by the FW,
and that's restricted to a few unicast management frames,
the only affect here is for those after a firmware restart.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.1cedf2ca7bb6.I2e609c28eaa301436e6740f4f1beca838f69a96a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
EAPOL failure results in deauthentication with various reasons, not
related to AUTH failure specifically, so we just merge AUTH failure
with failed to assoc to AP.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2ff350d85eab.I02c5b5d29c0d5c2e014bd1081b07ed33772ae04d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for discovery of hidden networks on the 6GHz band,
by including the scan request direct SSIDs in the FW scan request
command:
- In case a short SSID matches one of the direct SSIDs in the scan
request command, add the matching SSID in the same offset in the
'direct_ssids' array.
- Otherwise, add the SSID in one of the available slots.
Additionally, as a preparation to handle hidden APs, refactor
iwl_mvm_umac_scan_cfg_channels_v6_6g() the function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.ffb540a70212.Ia2bb9bc9435b833820bcc7dc30adcedb5a5a9869@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request processing populated the direct SSIDs
in the FW scan request command also for 6GHz scan, which is not
needed and might result in unexpected behavior.
Fix the code to add the direct SSIDs only in case the scan
is not a 6GHz scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.f465937c7bbf.Ic11a1659ddda850c3ec1b1afbe9e2b9577ac1800@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're waiting for the reset
handshake then it cannot possibly make progress anymore,
and we will just time out the wait. That's pointless, so
just stop waiting at that point.
Additionally, if it never acknowledges the reset handshake,
something went wrong.
Dump an error in both of these cases, but we need to do it
synchronously here since the device will be turned off.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.8b6a33544b4b.I55f97f70f8efa64db064a9207177a094c60ac8f1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When switching op-modes, or more generally when reconfiguring,
we might switch the RB size. In _iwl_pcie_rx_init() we have a
comment saying we must free all RBs since we might switch the
size, but this is actually too late: the switch has been done
and we'll free the buffers with the wrong size.
Fix this by always freeing the buffers, if any, at the start
of configure, instead of only after the size may have changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.42d7c93279c4.I07f74e65aab0e3d965a81206fcb289dc92d74878@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On 64-bit machines, struct iwl_rx_mem_buffer has a lot of
padding due to the use of pointers after the small items.
Move the list entry before them, and while at it also add
documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.6a62255b3df0.I47bb36530a3c2cdbd73454c796ce608ee2a32a6c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're already shutting down
the system, there isn't much we can do since the shutdown
process is continuing and we wanted to do that. Don't do
a FW restart, with the implied debug collection, in this
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.43a7351ae6bd.I164d48ce4379accf76ea0637983fd946d52dc6f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit ce78ffa3ef.
Wren and Nicolas reported that ath11k was failing to initialise QCA6390
Wi-Fi 6 device with error:
qcom_mhi_qrtr: probe of mhi0_IPCR failed with error -22
Commit ce78ffa3ef ("net: really fix the build..."), introduced in
v5.14-rc5, caused this regression in qrtr. Most likely all ath11k
devices are broken, but I only tested QCA6390. Let's revert the broken
commit so that ath11k works again.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210826172816.24478-1-kvalo@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the cmd index is obtained in debugfs by comparing file names.
However, this method may cause errors when processing more complex file
names. So, change this method by saving cmd in private data and comparing
it when getting cmd index in debugfs for optimization.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.
The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fc ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
network device that is commonly used in LiteX designs.
The driver was first written in 2017 and has been maintained by the
LiteX community in various trees. Thank you to all who have contributed.
Co-developed-by: Gabriel Somlo <gsomlo@gmail.com>
Co-developed-by: David Shah <dave@ds0.me>
Co-developed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a function for what has been magic register writes so far.
It's based on recent changes to vendor drivers r8101, r8168, r8125,
and deals with events that trigger an early ASPM L1 exit.
Description of the bits has been kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If otx2_mbox_get_rsp() fails, otx2_set_flowkey_cfg() need return an
error code.
Fixes: e793836545 ("octeontx2-pf: Fix algorithm index in MCAM rules with RSS action")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic schedules can only be started up to eight seconds within the
future. Therefore, the driver periodically checks every two seconds whether the
admin base time provided by the user is inside that window. If so the schedule
is started. Otherwise the check is deferred.
However, according to the programming manual the look ahead window size should
be four - not eight - seconds. By using the proposed value of four seconds
starting a schedule at a specified admin base time actually works as expected.
Fixes: 24dfc6eb39 ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the gate control list which is programmed into the hardware is
incorrect resulting in wrong traffic schedules. The problem is the loop
variables are incremented before they are referenced. Therefore, move the
increment to the end of the loop.
Fixes: 24dfc6eb39 ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we go into PROMISC mode when we have too many
filters by specifically counting the filters that successfully
get saved to the firmware.
The device advertises max_ucast_filters and max_mcast_filters,
but really only has max_ucast_filters slots available for
uc and mc filters combined.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The filter counting in ionic_lif_addr() really isn't useful,
and potentially misleading, especially when we're checking in
ionic_lif_rx_mode() to see if we need to go into PROMISC mode.
We can safely refactor this and remove a calling layer.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to separate the atomic needs of __dev_uc_sync()
and __dev_mc_sync() from the safe rx_mode handling, we need
to have the ndo handler manipulate the driver's filter list,
and later have the driver sync the filters to the firmware,
outside of the atomic context.
Here we put __dev_mc_sync() and __dev_uc_sync() back into the
ndo callback to give them their netif_addr_lock context and
have them update the driver's filter list, flagging changes
that should be made to the device filter list. Later, in the
rx_mode handler, we read those hints and sync up the device's
list as needed.
It is possible for multiple add/delete requests to come from
the stack before the rx_mode task processes the list, but the
handling of the sync status flag should keep everything sorted
correctly. For example, if a delete of an existing filter is
followed by another add before the rx_mode task is run, as can
happen when going in and out of a bond, the add will cancel
the delete and no actual changes will be sent to the device.
We also add a check in the watchdog to see if there are any
stray unsync'd filters, possibly left over from a filter
overflow and waiting to get sync'd after some other filter
gets removed to make room.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since only two functions call through ionic_set_rx_mode(), one
that can sleep and one that can't, we can split the function
and put the bits of code into the callers. This removes an
unnecessary calling layer.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the move of mac filter handling to outside of the
ndo_rx_mode context using the IONIC_DW_TYPE_RX_MODE,
we no longer are using IONIC_DW_TYPE_RX_ADDR_ADD and
IONIC_DW_TYPE_RX_ADDR_DEL and they can be removed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drivers/net/usb/asix_devices.c:757:60-65: WARNING: conversion to bool not needed here
Remove unneeded conversion to bool
Semantic patch information:
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unneeded.
Generated by: scripts/coccinelle/misc/boolconv.cocci
Fixes: 7a141e64cf ("net: usb: asix: ax88772: move embedded PHY detection as early as possible")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210825183538.13070-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added mbox for PF/VF drivers to retrieve current ingress bandwidth
profile free count. Also added current policer timeunit
configuration info based on which ratelimiting decisions can be
taken by PF/VF drivers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New usecases are popping up where in user wants to install common MCAM
filters for all interfaces. Having channel verification will result in
duplicating such MCAM filters for each of the ingress interface. Hence
removed channel verification.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K slicon has different device id for PTP device.
Hence this patch updates the driver with new id.
Though ptp driver being a separate driver AF manages
configuring PTP block by all PFs. To manage ptp, AF
driver checks in its probe whether
1. ptp hardware device found on silicon
2. A driver is bound to ptp device
3. The ptp driver probe is successful
In failure of cases 1 and 3, AF proceeds with out ptp
and for case 2 defers the probe. This patch refactors
code also to check for all the PTP device ids given in
ptp device ids table for case 1.
Also added PTP device ID for 95O silicon
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving the MBOX_MSG_FREE_RSRC_CNT, the AF will find out the
current number of free resources and reply it back to the requester. No
guarantee is given on the future state of the free resources yet.
If another requester sends MBOX_MSG_ATTACH_RESOURCES after this call,
the number of available resources might change.
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for packet IO via SDK links which is used when
Octeon is connected as a end-point. Traffic host to end-point
and vice versa flow through SDP links. This patch also support
dual SDP blocks supported in 98xx silicon.
Signed-off-by: Radha Mohan Chintakuntla <radhac@marvell.com>
Signed-off-by: Nalla Pradeep <pnalla@marvell.com>
Signed-off-by: Subrahmanyam Nilla <snilla@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 98xx, there are 2 NIX blocks and 4 LBK blocks present. The way
these NIX-LBK should be configured depends on the use case. By
default loopback functionality is supported in AF VF pairs which
are attached to NIX0 and NIX1 LFs alternatively to ensure load
balancing. NIX0 transmits a packet to LBK1 which will be received
by NIX1 and packet transmitted by NIX1 will get received by NIX0 via
LBK2.
There are some requirements where only one AF VF is used and respective
NIX is expected to operate in a mode where it can receive it own packet
back. This can be achieved if NIX0 sends packet to LBK0 and not LBK1.
Adding a flag in LF alloc request mailbox which can setup NIX0 to use
LBK0 and NIX1 can use LBK3.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike OcteonTx2, the channel numbers used by CGX/RPM
and LBK on CN10K silicons aren't fixed in HW. They are
SW programmable, hence we cannot derive transmit link
from static channel numbers anymore. Get the same from
admin function via mailbox.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before C0 HW revision, The RSS adder was computed based the
following static formula.
rss_adder<7:0> = flow_tag<7:0> ^ flow_tag<15:8> ^
flow_tag<23:16> ^ flow_tag<31:24>
The above scheme has the following drawbacks:
1) It is not in line with other standard NIC behavior.
2) There can be an SW use case where SW can compute the hash
upfront using Toeplitz function and predict the queue selection
to optimize some packet lookup function. The nonstandard
way of doing XOR makes the consumer to not predict the queue selection.
C0 HW revision onwards, The HW can configure the
rss_adder<7:0> as flow_tag<7:0> to align with standard NICs.
This patch adds an option to select legacy RSS adder mode
vs standard NIC behavior by setting NIX_LF_RSS_TAG_LSB_AS_ADDER flag.
Since this bit field is used as reserved in old HW revisions,
No need to have an additional HW version check.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from 96xx C0 onwards all silicons support traffic shaping.
This patch enables that feature along with other changes
- When PIR/CIR shaping config is modified, toggle SW_XOFF
for config to take effect
- Before SMQ flush, clear SW_XOFF at all parent schedulers
- Support to read current transmit scheduler configuration via mbox
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it's helpful for complie test in other platform(e.g.X86)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX_AF_TX_LINKX_NORM_CREDIT holds running counter of
tx credits available per link. But, tx credits should be
configured based on MTU config. So MTU change needs tx
credit count update.
An issue exists whereby when both PF & VF are enabled and
PF traffic is flowing, if VF requests for MTU update,
updating the NORM_CREDIT register will lead to corruption
of credit count and subsequent deadlock of tx link as
the NORM_CREDIT register holds running count.
This patch provides workaround by pausing link traffic
using NIX_AF_TL1X_SW_XOFF, waiting for existing packets to
drain, and used credits be returned before updating new
credit count.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear and disable interrupt before queueing work as there might be
a chance that work gets completed on other core faster and
interrupt enable as a part of the work completes before
interrupt disable in the interrupt context. This leads to
permanent disable of interrupt.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set NPA batch allocation engine to process 35 cache lines
per turn on CN10k platform.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmEmBioTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqR+jCACXWWBu1glFlohRY9Fds72CYYMndUnM
UZkZxvJJuFBhPgHTuBvlR1RYA8F5Dg4eaPXWkRBykun6CLc/4B33rxOuB4rdOjWt
V5VLrg0zoaQaVda2E3wZxpq+0G04+xYHBv1uzxu8GtwZM81wG+rmCu1kFgLLXN1B
iHz4YET41CNrJPpmipg26L+DoZgPnIP4f5L5cJnBeGJjuFkco7OMELoARk4ZB5So
KzDcNi52HK8QKNp5kaR3NHz9QqY7oAIWIDesxnU7Y/qqjhQ+gf0OLjgzLIB3LEqj
NOMa0MbrvtLXxPp6JuE9vSfQXWYMYz8+b8MqxyaMc2MdiwfGtXWYfqXp
=c6cY
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.15-20210825' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine says:
====================
pull-request: can-next 2021-08-25
this is a pull request of 4 patches for net-next/master.
The first patch is by Cai Huoqing, and enables COMPILE_TEST for the
rcar CAN drivers.
Lad Prabhakar contributes a patch for the rcar_canfd driver, fixing a
redundant assignment.
The last 2 patches are by Tang Bin, target the mscan driver, and clean
up the driver by converting it to of_device_get_match_data() and
removing a useless BUG_ON.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset support is present on R-Car. Let's support it, if it is
available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E-MAC IP on the R-Car AVB module has different initialization
parameters for RX frame size, duplex settings, different offset
for transfer speed setting and has magic packet detection support
compared to E-MAC on RZ/G2L Gigabit Ethernet module. Factorise
the ravb_emac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC IP on the R-Car AVB module has different initialization
parameters for RCR, TGC, TCCR, RIC0, RIC2, and TIC compared to
DMAC IP on the RZ/G2L Gigabit Ethernet module. Factorise the
ravb_dmac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports HW checksum on RX and TX whereas R-Car supports on RX.
Factorise ravb_set_features to support this feature.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports 100 and 1000 Mbps transfer speed whereas RZ/G2L
in addition support 10Mbps. Factorise ravb_adjust_link function
in order to support 10Mbps speed.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses an extended descriptor in RX whereas, RZ/G2L uses
normal descriptor in RX. Factorise the ravb_rx function to
support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_init function uses an extended descriptor in RX for
R-Car and normal descriptor for RZ/G2L. Add a helper function
for RX ring buffer allocation to support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_format function uses an extended descriptor in RX
for R-Car compared to the normal descriptor for RZ/G2L. Factorise
RX ring buffer buildup to extend the support for later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses extended descriptor in RX, whereas RZ/G2L uses normal
descriptor. Factorise ravb_ring_free function so that it can
support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen3, gPTP support is active in config mode.
2) On R-Car Gen2, gPTP support is not active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a ptp_cfg_active hw feature bit to struct ravb_hw_info for
supporting gPTP active in config mode for R-Car Gen3.
This patch also removes enum ravb_chip_id, chip_id from both
struct ravb_hw_info and struct ravb_private, as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen2, gPTP support is not active in config mode.
2) On R-Car Gen3, gPTP support is active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a no_ptp_cfg_active hw feature bit to struct ravb_hw_info for
handling gPTP for R-Car Gen2.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports separate interrupts for E-MAC and DMA queues,
whereas R-Car Gen2 and RZ/G2L have a single interrupt instead.
Add a multi_irq hw feature bit to struct ravb_hw_info to enable
this only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For addressing 4 bytes alignment restriction on transmission
buffer for R-Car Gen2 we use 2 descriptors whereas it is a single
descriptor for other cases.
Replace the macros NUM_TX_DESC_GEN[23] with magic number and
add a comment to explain it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in commit 38b5beeae7 ("net: dsa: sja1105: prepare tagger
for handling DSA tags and VLAN simultaneously"), the sja1105_xmit_tpid
function solved quite a different problem than our needs are now.
Then, we used best-effort VLAN filtering and we were using the xmit_tpid
to tunnel packets coming from an 8021q upper through the TX VLAN allocated
by tag_8021q to that egress port. The need for a different VLAN protocol
depending on switch revision came from the fact that this in itself was
more of a hack to trick the hardware into accepting tunneled VLANs in
the first place.
Right now, we deny 8021q uppers (see sja1105_prechangeupper). Even if we
supported them again, we would not do that using the same method of
{tunneling the VLAN on egress, retagging the VLAN on ingress} that we
had in the best-effort VLAN filtering mode. It seems rather simpler that
we just allocate a VLAN in the VLAN table that is simply not used by the
bridge at all, or by any other port.
Anyway, I have 2 gripes with the current sja1105_xmit_tpid:
1. When sending packets on behalf of a VLAN-aware bridge (with the new
TX forwarding offload framework) plus untagged (with the tag_8021q
VLAN added by the tagger) packets, we can see that on SJA1105P/Q/R/S
and later (which have a qinq_tpid of ETH_P_8021AD), some packets sent
through the DSA master have a VLAN protocol of 0x8100 and others of
0x88a8. This is strange and there is no reason for it now. If we have
a bridge and are therefore forced to send using that bridge's TPID,
we can as well blend with that bridge's VLAN protocol for all packets.
2. The sja1105_xmit_tpid introduces a dependency on the sja1105 driver,
because it looks inside dp->priv. It is desirable to keep as much
separation between taggers and switch drivers as possible. Now it
doesn't do that anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver is a bit special in its use of VLAN headers as DSA
tags. This is because in VLAN-aware mode, the VLAN headers use an actual
TPID of 0x8100, which is understood even by the DSA master as an actual
VLAN header.
Furthermore, control packets such as PTP and STP are transmitted with no
VLAN header as a DSA tag, because, depending on switch generation, there
are ways to steer these control packets towards a precise egress port
other than VLAN tags. Transmitting control packets as untagged means
leaving a door open for traffic in general to be transmitted as untagged
from the DSA master, and for it to traverse the switch and exit a random
switch port according to the FDB lookup.
This behavior is a bit out of line with other DSA drivers which have
native support for DSA tagging. There, it is to be expected that the
switch only accepts DSA-tagged packets on its CPU port, dropping
everything that does not match this pattern.
We perhaps rely a bit too much on the switches' hardware dropping on the
CPU port, and place no other restrictions in the kernel data path to
avoid that. For example, sja1105 is also a bit special in that STP/PTP
packets are transmitted using "management routes"
(sja1105_port_deferred_xmit): when sending a link-local packet from the
CPU, we must first write a SPI message to the switch to tell it to
expect a packet towards multicast MAC DA 01-80-c2-00-00-0e, and to route
it towards port 3 when it gets it. This entry expires as soon as it
matches a packet received by the switch, and it needs to be reinstalled
for the next packet etc. All in all quite a ghetto mechanism, but it is
all that the sja1105 switches offer for injecting a control packet.
The driver takes a mutex for serializing control packets and making the
pairs of SPI writes of a management route and its associated skb atomic,
but to be honest, a mutex is only relevant as long as all parties agree
to take it. With the DSA design, it is possible to open an AF_PACKET
socket on the DSA master net device, and blast packets towards
01-80-c2-00-00-0e, and whatever locking the DSA switch driver might use,
it all goes kaput because management routes installed by the driver will
match skbs sent by the DSA master, and not skbs generated by the driver
itself. So they will end up being routed on the wrong port.
So through the lens of that, maybe it would make sense to avoid that
from happening by doing something in the network stack, like: introduce
a new bit in struct sk_buff, like xmit_from_dsa. Then, somewhere around
dev_hard_start_xmit(), introduce the following check:
if (netdev_uses_dsa(dev) && !skb->xmit_from_dsa)
kfree_skb(skb);
Ok, maybe that is a bit drastic, but that would at least prevent a bunch
of problems. For example, right now, even though the majority of DSA
switches drop packets without DSA tags sent by the DSA master (and
therefore the majority of garbage that user space daemons like avahi and
udhcpcd and friends create), it is still conceivable that an aggressive
user space program can open an AF_PACKET socket and inject a spoofed DSA
tag directly on the DSA master. We have no protection against that; the
packet will be understood by the switch and be routed wherever user
space says. Furthermore: there are some DSA switches where we even have
register access over Ethernet, using DSA tags. So even user space
drivers are possible in this way. This is a huge hole.
However, the biggest thing that bothers me is that udhcpcd attempts to
ask for an IP address on all interfaces by default, and with sja1105, it
will attempt to get a valid IP address on both the DSA master as well as
on sja1105 switch ports themselves. So with IP addresses in the same
subnet on multiple interfaces, the routing table will be messed up and
the system will be unusable for traffic until it is configured manually
to not ask for an IP address on the DSA master itself.
It turns out that it is possible to avoid that in the sja1105 driver, at
least very superficially, by requesting the switch to drop VLAN-untagged
packets on the CPU port. With the exception of control packets, all
traffic originated from tag_sja1105.c is already VLAN-tagged, so only
STP and PTP packets need to be converted. For that, we need to uphold
the equivalence between an untagged and a pvid-tagged packet, and to
remember that the CPU port of sja1105 uses a pvid of 4095.
Now that we drop untagged traffic on the CPU port, non-aggressive user
space applications like udhcpcd stop bothering us, and sja1105 effectively
becomes just as vulnerable to the aggressive kind of user space programs
as other DSA switches are (ok, users can also create 8021q uppers on top
of the DSA master in the case of sja1105, but in future patches we can
easily deny that, but it still doesn't change the fact that VLAN-tagged
packets can still be injected over raw sockets).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is possible for an attacker to craft packets with a fake
DSA tag and send them to us, and our user ports will accept them and
preserve that VLAN when transmitting towards the CPU. Then the tagger
will be misled into thinking that the packets came on a different port
than they really came on.
Up until recently there wasn't a good option to prevent this from
happening. In SJA1105P and later, the MAC Configuration Table introduced
two options called:
- DRPSITAG: Drop Single Inner Tagged Frames
- DRPSOTAG: Drop Single Outer Tagged Frames
Because the sja1105 driver classifies all VLANs as "outer VLANs" (S-Tags),
it would be in principle possible to enable the DRPSOTAG bit on ports
using tag_8021q, and drop on ingress all packets which have a VLAN tag.
When the switch is VLAN-unaware, this works, because it uses a custom
TPID of 0xdadb, so any "tagged" packets received on a user port are
probably a spoofing attempt. But when the switch overall is VLAN-aware,
and some ports are standalone (therefore they use tag_8021q), the TPID
is 0x8100, and the port can receive a mix of untagged and VLAN-tagged
packets. The untagged ones will be classified to the tag_8021q pvid, and
the tagged ones to the VLAN ID from the packet header. Yes, it is true
that since commit 4fbc08bd36 ("net: dsa: sja1105: deny 8021q uppers on
ports") we no longer support this mixed mode, but that is a temporary
limitation which will eventually be lifted. It would be nice to not
introduce one more restriction via DRPSOTAG, which would make the
standalone ports of a VLAN-aware switch drop genuinely VLAN-tagged
packets.
Also, the DRPSOTAG bit is not available on the first generation of
switches (SJA1105E, SJA1105T). So since one of the key features of this
driver is compatibility across switch generations, this makes it an even
less desirable approach.
The breakthrough comes from commit bef0746cf4 ("net: dsa: sja1105:
make sure untagged packets are dropped on ingress ports with no pvid"),
where it became obvious that untagged packets are not dropped even if
the ingress port is not in the VMEMB_PORT vector of that port's pvid.
However, VLAN-tagged packets are subject to VLAN ingress
checking/dropping. This means that instead of using the catch-all
DRPSOTAG bit introduced in SJA1105P, we can drop tagged packets on a
per-VLAN basis, and this is already compatible with SJA1105E/T.
This patch adds an "allowed_ingress" argument to sja1105_vlan_add(), and
we call it with "false" for tag_8021q VLANs on user ports. The tag_8021q
VLANs still need to be allowed, of course, on ingress to DSA ports and
CPU ports.
We also need to refine the drop_untagged check in sja1105_commit_pvid to
make it not freak out about this new configuration. Currently it will
try to keep the configuration consistent between untagged and pvid-tagged
packets, so if the pvid of a port is 1 but VLAN 1 is not in VMEMB_PORT,
packets tagged with VID 1 will behave the same as untagged packets, and
be dropped. This behavior is what we want for ports under a VLAN-aware
bridge, but for the ports with a tag_8021q pvid, we want untagged
packets to be accepted, but packets tagged with a header recognized by
the switch as a tag_8021q VLAN to be dropped. So only restrict the
drop_untagged check to apply to the bridge_pvid, not to the tag_8021q_pvid.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was relying on dsa_slave_vlan_rx_add_vid to add VLAN ID 0. After
the blamed commit, VLAN ID 0 won't be set up anymore, breaking software
bridging fallback on VLAN-unaware bridges.
Manually set up VLAN ID 0 to fix this.
Fixes: 06cfb2df7e ("net: dsa: don't advertise 'rx-vlan-filter' when not needed")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not an expected case normally.
Add WARN_ON_ONCE in case of CQE read overflow, instead of failing
silently.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code uses (1 + #vPorts * #Queues) MSIXs, which may exceed
the device limit.
Support EQ sharing, so that multiple vPorts (NICs) can share the same
set of MSIXs.
And, report the EQ-sharing capability bit to the host, which means the
host can potentially offer more vPorts and queues to the VM.
Also update the resource limit checking and error handling for better
robustness.
Now, we support up to 256 virtual ports per VF (it was 16/VF), and
support up to 64 queues per vPort (it was 16).
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code has NAPI threads polling on EQ directly. To prepare
for EQ sharing among vPorts, move NAPI from EQ to CQ so that one EQ
can serve multiple CQs from different vPorts.
The "arm bit" is only set when CQ processing is completed to reduce
the number of EQ entries, which in turn reduce the number of interrupts
on EQ.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function 'netxen_rom_fast_read' is declared twice, so remove the
repeated declaration.
Cc: Manish Chopra <manishc@marvell.com>
Cc: Rahul Verma <rahulv@marvell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2785:2: error: variable 'kw_offset' is uninitialized when used here [-Werror,-Wuninitialized]
FIND_VPD_KW(i, "RV");
^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2776:39: note: expanded from macro 'FIND_VPD_KW'
var = pci_vpd_find_info_keyword(vpd, kw_offset, vpdr_len, name); \
^~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2748:34: note: initialize the variable 'kw_offset' to silence this warning
unsigned int vpdr_len, kw_offset, id_len;
^
= 0
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2785:2: error: variable 'vpdr_len' is uninitialized when used here [-Werror,-Wuninitialized]
FIND_VPD_KW(i, "RV");
^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2776:50: note: expanded from macro 'FIND_VPD_KW'
var = pci_vpd_find_info_keyword(vpd, kw_offset, vpdr_len, name); \
^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2748:23: note: initialize the variable 'vpdr_len' to silence this warning
unsigned int vpdr_len, kw_offset, id_len;
^
= 0
2 errors generated.
The series "PCI/VPD: Convert more users to the new VPD API functions"
was applied to net-next when it should have been applied to the PCI tree
because of build errors. However, commit 82e34c8a9b ("Revert "Revert
"cxgb4: Search VPD with pci_vpd_find_ro_info_keyword()""") reapplied a
change, resulting in the warning above.
Properly revert commit 8d63ee602d ("cxgb4: Search VPD with
pci_vpd_find_ro_info_keyword()") to fix the warning and restore proper
functionality. This also reverts commit 3a93bedea0 ("cxgb4: Remove
unused vpd_param member ec") to avoid future merge conflicts, as that
change has been applied to the PCI tree.
Link: https://lore.kernel.org/r/20210823120929.7c6f7a4f@canb.auug.org.au/
Link: https://lore.kernel.org/r/1ca29408-7bc7-4da5-59c7-87893c9e0442@gmail.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure a valid XSK buffer before proceed to free the xdp buffer.
The following kernel panic is observed without this patch:
RIP: 0010:xp_free+0x5/0x40
Call Trace:
stmmac_napi_poll_rxtx+0x332/0xb30 [stmmac]
? stmmac_tx_timer+0x3c/0xb0 [stmmac]
net_rx_action+0x13d/0x3d0
__do_softirq+0xfc/0x2fb
? smpboot_register_percpu_thread+0xe0/0xe0
run_ksoftirqd+0x32/0x70
smpboot_thread_fn+0x1d8/0x2c0
kthread+0x169/0x1a0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
---[ end trace 0000000000000002 ]---
Fixes: bba2556efa ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.
Fix this by changing the XDP pool setup sequence to:
1. disable napi before free xsk_pool
2. enable napi after init xsk_pool
The following kernel panic is observed without this patch:
RIP: 0010:xsk_uses_need_wakeup+0x5/0x10
Call Trace:
stmmac_napi_poll_rxtx+0x3a9/0xae0 [stmmac]
__napi_poll+0x27/0x130
net_rx_action+0x233/0x280
__do_softirq+0xe2/0x2b6
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xac/0x140
? sort_range+0x20/0x20
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
---[ end trace a77c8956b79ac107 ]---
Fixes: bba2556efa ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-08-24
Vinicius Costa Gomes says:
This adds support for PCIe PTM (Precision Time Measurement) to the igc
driver. PCIe PTM allows the NIC and Host clocks to be compared more
precisely, improving the clock synchronization accuracy.
Patch 1/4 reverts a commit that made pci_enable_ptm() private to the
PCI subsystem, reverting makes it possible for it to be called from
the drivers.
Patch 2/4 adds the pcie_ptm_enabled() helper.
Patch 3/4 calls pci_enable_ptm() from the igc driver.
Patch 4/4 implements the PCIe PTM support. Exposing it via the
.getcrosststamp() API implies that the time measurements are made
synchronously with the ioctl(). The hardware was implemented so the
most convenient way to retrieve that information would be
asynchronously. So, to follow the expectations of the ioctl() we have
to use less convenient ways, triggering an PCIe PTM dialog every time
a ioctl() is received.
Some questions are raised (also pointed out in the commit message):
1. Using convert_art_ns_to_tsc() is too x86 specific, there should be
a common way to create a 'system_counterval_t' from a timestamp.
2. convert_art_ns_to_tsc() says that it should only be used when
X86_FEATURE_TSC_KNOWN_FREQ is true, but during tests it works even
when it returns false. Should that check be done?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Device removal can result in a large burst of driver warning messages
(20 - 30) sent to the kernel log. Most of these are register read/write
failures.
This change limits the rate at which these messages are emitted.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a device disconnect at roughly the same time as a
deferred PHY link reset there is a race condition that can result
in a kernel lock up due to a null pointer dereference in the
driver's deferred work handling routine lan78xx_delayedwork().
The following changes fix this problem.
Add new status flag EVENT_DEV_DISCONNECT to indicate when the
device has been removed and use it to prevent operations, such as
register access, that will fail once the device is removed.
Stop processing of deferred work items when the driver's USB
disconnect handler is invoked.
Disconnect the PHY only after the network device has been
unregistered and all delayed work has been cancelled.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is given an IP address while the device is
suspended (as a result of an auto-suspend event) there is a race
between lan78xx_resume() and lan78xx_open() that can result in an
exception or failure to handle incoming packets. The following
changes fix this problem.
Introduce a mutex to serialise operations in the network interface
open and stop entry points with respect to the USB driver suspend
and resume entry points.
Move Tx and Rx data path start/stop to lan78xx_start() and
lan78xx_stop() respectively and flush the packet FIFOs before
starting the Tx and Rx data paths. This prevents the MAC and FIFOs
getting out of step and delivery of malformed packets to the network
stack.
Stop processing of received packets before disconnecting the
PHY from the MAC to prevent a kernel exception caused by handling
packets after the PHY device has been removed.
Refactor device auto-suspend code to make it consistent with the
the system suspend code and make the suspend handler easier to read.
Add new code to stop wake-on-lan packets or PHY events resuming the
host or device from suspend if the device has not been opened
(typically after an IP address is assigned).
This patch is dependent on changes to lan78xx_suspend() and
lan78xx_resume() introduced in the previous patch of this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC can get out of step with the internal packet FIFOs if the
system goes to sleep when the link is active, especially at high
data rates. This can result in partial frames in the packet FIFOs
that in result in malformed frames being delivered to the host.
This occurs because the driver does not enable/disable the internal
packet FIFOs in step with the corresponding MAC data path. The
following changes fix this problem.
Update code that enables/disables the MAC receiver and transmitter
to the more general Rx and Tx data path, where the data path in each
direction consists of both the MAC function (Tx or Rx) and the
corresponding packet FIFO.
In the receive path the packet FIFO must be enabled before the MAC
receiver but disabled after the MAC receiver.
In the transmit path the opposite is true: the packet FIFO must be
enabled after the MAC transmitter but disabled before the MAC
transmitter.
The packet FIFOs can be flushed safely once the corresponding data
path is stopped.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An exception is sometimes seen when the link speed is changed
from auto-negotiation to a fixed speed, or vice versa. The
exception occurs when the MAC is reset (due to the link speed
change) at the same time as the PHY state machine is accessing
a PHY register. The following changes fix this problem.
Rework the MAC reset to ensure there is no outstanding MDIO
register transaction before the reset and then wait until the
reset is complete before allowing any further MAC register access.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places in the driver where the return code from a
function call is captured but without a subsequent test of the
return code and appropriate action taken.
This patch adds the missing return code tests and action. In most
cases the action is an early exit from the calling function.
The function lan78xx_set_suspend() was also updated to make it
consistent with lan78xx_suspend().
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the pause frame queue from the driver. It is initialised
but not actually used.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set threshold at which flow control is triggered to 3/4 full of
the internal Rx packet FIFO to prevent packet drops at high data
rates. The new setting reduces the number of dropped UDP frames
and TCP retransmit requests especially on less capable CPUs.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kernel timer that is not used by the driver.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix white space and code style issues identified by checkpatch.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables automatic recovery by default in case of various
error condition like fw assert , hardware error etc.
This also ensure driver can handle multiple iteration of assertion
conditions.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2c896fb02e
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.
In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.
The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function mpc5xxx_can_probe(), the variable 'data' has already
been determined in the above code, so the BUG_ON() in this place is
useless, remove it.
Link: https://lore.kernel.org/r/20210823141033.17876-1-tangbin@cmss.chinamobile.com
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix redundant assignment of 'priv' to itself in
rcar_canfd_handle_channel_tx().
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/r/20210820161449.18169-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enables PCIe PTM (Precision Time Measurement) support in the igc
driver. Notifies the PCI devices that PCIe PTM should be enabled.
PCIe PTM is similar protocol to PTP (Precision Time Protocol) running
in the PCIe fabric, it allows devices to report time measurements from
their internal clocks and the correlation with the PCIe root clock.
The i225 NIC exposes some registers that expose those time
measurements, those registers will be used, in later patches, to
implement the PTP_SYS_OFFSET_PRECISE ioctl().
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Link: https://lore.kernel.org/r/62522a24-f39a-2b35-1577-1fbb41695bed@gmail.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Use strncasecmp() to match Vendor ID instead of comparing with lower- and
upper-case hex string.
[bhelgaas: convert to strncasecmp()]
Link: https://lore.kernel.org/r/a9f730cf-e31e-902b-7b39-0ff2e99636e0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Link: https://lore.kernel.org/r/821a334d-ff9d-386e-5f42-9b620ab3dbfa@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Read NVRAM directly into buffer and use swab32s() to byte swap it in-place
instead of reading it into the end of the buffer and swapping it manually
while copying it.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/e4ac6229-1df5-8760-3a87-1ad0ace87137@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Replace netif_err() with pci_err() because the netdevice isn't registered
yet, which results in very ugly messages.
Use kmemdup_nul() instead of open-coding it.
This is the same as 37838aa437 ("sfc: Search VPD with
pci_vpd_find_ro_info_keyword()"), just for the falcon chip version.
Link: https://lore.kernel.org/r/898282a1-13bd-17bc-2e9a-d3dcd336b46c@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This avoids having to allocate a buffer on the stack, and we don't have to
make any assumptions on VPD size and location of information in VPD.
This is the same as 5119e20fac ("sfc: Read VPD with pci_vpd_alloc()"),
just for the falcon chip version.
Link: https://lore.kernel.org/r/2a8d069e-9516-50d8-6520-2614222c8f5f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support in ethtool for switching EQE/CQE mode.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For device whose version is above V3(include V3), the GL can
select EQE or CQE mode, so adds support for it.
In CQE mode, the coalesced timer will restart when the first new
completion occurs, while in EQE mode, the timer will not restart.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ASPM is disabled completely because we've seen different types of
problems in the past. However it seems these problems occurred with
L1 or L1 sub-states only. On all the chip versions I've seen the
acceptable L0s exit latency is 512ns. This should be short enough not
to cause problems. If the actual L0s exit latency of the PCIe link
is bigger than 512ns then the PCI core will disable L0s anyway.
So let's give it a try and disable L1 and L1 sub-states only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In early erratas this issue only covered port 0 when changing from
[x]MII (rev A 3.6). In subsequent errata versions this errata changed to
cover the additional "Hardware reset in CPU managed mode" condition, and
removed the note specifying that it only applied to port 0.
In designs where the device is configured with CPU managed mode
(CPU_MGD), on reset all SERDES ports (p0, p9, p10) have a stuck power
down bit and require this initial power up procedure. As such apply this
errata to all three SERDES ports of the mv88e6393x.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit e358bef7c3 ("net: dsa: Give drivers the chance
to veto certain upper devices"), the hellcreek driver uses some tricks
to comply with the network stack expectations: it enforces port
separation in standalone mode using VLANs. For untagged traffic,
bridging between ports is prevented by using different PVIDs, and for
VLAN-tagged traffic, it never accepts 8021q uppers with the same VID on
two ports, so packets with one VLAN cannot leak from one port to another.
That is almost fine*, and has worked because hellcreek relied on an
implicit behavior of the DSA core that was changed by the previous
patch: the standalone ports declare the 'rx-vlan-filter' feature as 'on
[fixed]'. Since most of the DSA drivers are actually VLAN-unaware in
standalone mode, that feature was actually incorrectly reflecting the
hardware/driver state, so there was a desire to fix it. This leaves the
hellcreek driver in a situation where it has to explicitly request this
behavior from the DSA framework.
We configure the ports as follows:
- Standalone: 'rx-vlan-filter' is on. An 8021q upper on top of a
standalone hellcreek port will go through dsa_slave_vlan_rx_add_vid
and will add a VLAN to the hardware tables, giving the driver the
opportunity to refuse it through .port_prechangeupper.
- Bridged with vlan_filtering=0: 'rx-vlan-filter' is off. An 8021q upper
on top of a bridged hellcreek port will not go through
dsa_slave_vlan_rx_add_vid, because there will not be any attempt to
offload this VLAN. The driver already disables VLAN awareness, so that
upper should receive the traffic it needs.
- Bridged with vlan_filtering=1: 'rx-vlan-filter' is on. An 8021q upper
on top of a bridged hellcreek port will call dsa_slave_vlan_rx_add_vid,
and can again be vetoed through .port_prechangeupper.
*It is not actually completely fine, because if I follow through
correctly, we can have the following situation:
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0 # lan0 now becomes VLAN-unaware
ip link set lan0 nomaster # lan0 fails to become VLAN-aware again, therefore breaking isolation
This patch fixes that corner case by extending the DSA core logic, based
on this requested attribute, to change the VLAN awareness state of the
switch (port) when it leaves the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the interface name and PCI address are printed twice, because
netdev_info() is printing this information implicitly already. This results
in messages like the following. remove the duplicated information.
cxgb4 0000:81:00.4 eth3: eth3: Chelsio T6225-OCP-SO (0000:81:00.4) 1G/10G/25GBASE-SFP28
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix crash on reboot on a system with ASIX AX88178 USB adapter attached
to it:
| asix 1-1.4:1.0 eth0: unregister 'asix' usb-ci_hdrc.0-1.4, ASIX AX88178 USB 2.0 Ethernet
| 8<--- cut here ---
| Unable to handle kernel NULL pointer dereference at virtual address 0000028c
| pgd = 5ec93aee
| [0000028c] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 5.14.0-rc1-20210811-1 #4
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| PC is at phy_disconnect+0x8/0x48
| LR is at ax88772_unbind+0x14/0x20
| [<80650d04>] (phy_disconnect) from [<80741aa4>] (ax88772_unbind+0x14/0x20)
| [<80741aa4>] (ax88772_unbind) from [<8074e250>] (usbnet_disconnect+0x48/0xd8)
| [<8074e250>] (usbnet_disconnect) from [<807655e0>] (usb_unbind_interface+0x78/0x25c)
| [<807655e0>] (usb_unbind_interface) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
| [<805ab26c>] (device_del) from [<807634a4>] (usb_disable_device+0xcc/0x178)
| [<807634a4>] (usb_disable_device) from [<8075a060>] (usb_disconnect+0xd8/0x238)
| [<8075a060>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<80af3520>] (usb_remove_hcd+0xa0/0x198)
| [<80af3520>] (usb_remove_hcd) from [<807902e0>] (host_stop+0x38/0xa8)
| [<807902e0>] (host_stop) from [<8078d9e4>] (ci_hdrc_remove+0x3c/0x118)
| [<8078d9e4>] (ci_hdrc_remove) from [<805b27ec>] (platform_remove+0x20/0x50)
| [<805b27ec>] (platform_remove) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
For this adapter we call ax88178_bind() and ax88772_unbind(), which is
related to different chip version and different counter part *bind()
function.
Since this chip is currently not ported to the PHYLIB, we do not need to
call phy_disconnect() here. So, to fix this crash, we need to add
ax88178_unbind().
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Robin van der Gracht <robin@protonic.nl>
Tested-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HW revisions need additional MAC configuration before the embedded PHY
can be enabled. If this is not done, we won't be able to get response
from the internal PHY.
This issue was detected on chipcode == AX_AX88772_CHIPCODE variant,
where ax88772_hw_reset() was executed with missing embd_phy flag.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.15. This got delayed as I have been mostly
offline for the last few weeks. The biggest change is removal of
prism54 driver, otherwise just smaller changes.
Major changes:
ath5k, ath9k, ath10k, ath11k:
* switch from 'pci_' to 'dma_' API
brcmfmac
* allow per-board firmware binaries
* add support 43752 SDIO device
prism54
* remove the obsoleted driver, everyone should be using p54 driver instead
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmEiEGcVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b0UoH+wT2LyZ92PZUxL5FwUl1kFIRKefw
8H5urbnlioiqFjKU9YAwD3bvGTrIPMGjOkR50JxPNxxKzcx5CgHz6GQmIe16aSs2
FEMV//G5dcGe7HS94kdOiBhm6EqLrr+hrqWRop+uEnu9DuQNxnS/5ZpxU6zNSK7z
S2u2m/zpcaE6/F+Po1jlGyPRzUbTR8xV/3a7LKUgbZslbrGKayn+3aQwFXZ4D8YX
OhGrsL5nbFjKP0Ys7X/QS9s31IuzMBO5IUVMyJzcY7p6pPPFspxiGaT+HqUixZ9G
eb0hStxXANDAQbhBgz2KpIGH8J/0g8WdUwUj4SuiHOrhPSga6HZ06MhJ5xk=
=djwO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.15
First set of patches for v5.15. This got delayed as I have been mostly
offline for the last few weeks. The biggest change is removal of
prism54 driver, otherwise just smaller changes.
Major changes:
ath5k, ath9k, ath10k, ath11k:
* switch from 'pci_' to 'dma_' API
brcmfmac
* allow per-board firmware binaries
* add support 43752 SDIO device
prism54
* remove the obsoleted driver, everyone should be using p54 driver instead
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of these macros has been removed in commit db1a8611c8
("sunhme: Convert to pure OF driver."). So they can be removed.
This simplifies code and helps for removing the wrappers in
include/linux/pci-dma-compat.h.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-08-20
This series contains updates to igc and e1000e drivers.
Aaron Ma resolves a page fault which occurs when thunderbolt is
unplugged for igc.
Toshiki Nishioka fixes Tx queue looping to use actual number of queues
instead of max value for igc.
Sasha fixes an incorrect latency comparison by decoding the values before
comparing and prevents attempted writes to read-only NVMs for e1000e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab2 ("drivers: net: xgene-v2: Add MDIO support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
This pulls mlx5-next branch which includes patches already reviewed on
net-next and rdma mailing lists.
1) mlx5 single E-Switch FDB for lag
2) IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
3) Add DCS caps & fields support
We need this in net-next as multiple features are dependent on the
single FDB feature.
====================
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
* mellanox/mlx5-next:
net/mlx5: Lag, Create shared FDB when in switchdev mode
net/mlx5: E-Switch, add logic to enable shared FDB
net/mlx5: Lag, move lag destruction to a workqueue
net/mlx5: Lag, properly lock eswitch if needed
net/mlx5: Add send to vport rules on paired device
net/mlx5: E-Switch, Add event callback for representors
net/mlx5e: Use shared mappings for restoring from metadata
net/mlx5e: Add an option to create a shared mapping
net/mlx5: E-Switch, set flow source for send to uplink rule
RDMA/mlx5: Add shared FDB support
{net, RDMA}/mlx5: Extend send to vport rules
RDMA/mlx5: Fill port info based on the relevant eswitch
net/mlx5: Lag, add initial logic for shared FDB
net/mlx5: Return mdev from eswitch
IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the VPD checksum with pci_vpd_check_csum() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
str_id_reg and str_id_cap hold the same string and are used in the same
comparison. This doesn't make sense, use one string str_id instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as 37838aa437 "sfc: Search VPD with
pci_vpd_find_ro_info_keyword()", just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as 5119e20fac "sfc: Read VPD with pci_vpd_alloc()",
just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 01848e05f8 ("mlxsw: spectrum_router: Add support for inner
layer 3 multipath hash policy") and commit daeabf89eb ("mlxsw:
spectrum_router: Add support for custom multipath hash policy") added
support for multipath hash policies where the hash is calculated based
on inner packet fields.
For IPv6-in-IPv6 packets, the default parsing depth (96 bytes) is not
enough when these policies are used.
Therefore, for such cases, call the new API to increase / decrease the
parsing depth as necessary. Care is taken to ensure the API is not
called multiple times.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches added new API to handle parsing depth and converted
the existing code to use it.
Remove the old infrastructure which is not needed anymore.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert VxLAN and PTP modules to increase parsing depth using new API
that was added in the previous patch.
Separate MPRS register's configuration to VxLAN related configuration
and parsing depth configuration. Handle each one using the appropriate
API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum ASICs have a configurable limit on how deep into the packet
they parse. By default, the limit is 96 bytes.
There are several cases where this parsing depth is not enough and there
is a need to increase it. Currently, increasing parsing depth is
maintained as part of VxLAN module, because the MPRS register which
configures parsing depth also configures UDP destination port number
used for VxLAN encapsulation and decapsulation.
Add an API for increasing parsing depth as part of spectrum.c code, so
that it will be possible to use it from other modules. In addition, add
an API for setting UDP destination port and protect it using a dedicated
lock for saving parsing configurations. The lock is needed as not all
the callers hold RTNL lock.
Maintain a counter for increased parsing depth consumers. For first
consumer subscription, increase the parsing depth and for last consumer
unsubscription, set parsing depth to default value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RVU SMMU widget stores the final translated PA at
RVU_AF_SMMU_TLN_FLIT0<57:18> instead of FLIT1 register. This patch
fixes the address translation logic to use the correct register.
Fixes: 893ae97214 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherthan setting action as RSS in NPC MCAM entry, RSS flowkey
algorithm index also needs to be set. Otherwise whatever algorithm
is defined at flowkey index '0' will be considered by HW and pkt
flows will be distributed as such.
Fix this by saving the flowkey index sent by admin function while
initializing RSS and then use it when framing MCAM rules.
Fixes: 81a4362016 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever user changes interface MAC address both default DMAC based
MCAM rule and VLAN offload (for strip) rules are updated with new
MAC address. To update or install VLAN offload rule PF driver needs
interface's receive channel info, which is retrieved from admin
function at the time of NIXLF initialization.
If user changes MAC address before interface is UP, VLAN offload rule
installation will fail and throw error as receive channel is not valid.
To avoid this, skip VLAN offload rule installation if netdev is not UP.
This rule will anyway be reinslatted as part of open() call.
Fixes: fd9d7859db ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bandwidth profiles (ipolicer structure)is implemented only on CN10K
platform. But current code try to free the ipolicer memory without
checking the capibility flag leading to driver crash on OCTEONTX2
platform. This patch fixes the issue by add capability flag check.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K platform requires physically contiguous memory for LMTST
operations which goes beyond a single page. Not having physically
contiguous memory will result in HW fetching transmit descriptors from
a wrong memory location.
Hence use DMA_ATTR_FORCE_CONTIGUOUS attribute while allocating
LMTST regions.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the erroneous vlan priority mask field that was
send to npc_install_flow_req.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported link modes are updated by firmware in shared
structure per interface. Kernel uses this value to display
supported link modes via ethtool.
Currently there is extra validation that firmware updated
modes are validated against internal list of supported modes.
As intenal list of supported modes are not updated frequently
new modes supported by firmware are not updated to ethtool.
Hence remove extra validation and report all firmware updated
modes.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print debug message if any of the RVU hardware blocks
reset fails.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per hardware the base channel number configured
for programmable channels of a block must be multiple
of number of channels of that block. This condition
is not met for SDP base channel currently. Hence this
patch ensures all the base channel numbers of all
blocks are multiple of number of channels present in
the blocks. Also instead of hardcoding SDP number
of channels the same is read from the NIX_AF_CONST1
register.
Fixes: 242da43921 ("octeontx2-af: cn10k: Add support for programmable")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename "ipa_clock.c" to be "ipa_power.c" and "ipa_clock.h"
to be "ipa_power.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename a number of functions to clarify that there is no longer a
notion of an "IPA clock," but rather that the functions are more
generally related to IPA power management.
ipa_clock_enable() -> ipa_power_enable()
ipa_clock_disable() -> ipa_power_disable()
ipa_clock_rate() -> ipa_core_clock_rate()
ipa_clock_init() -> ipa_power_init()
ipa_clock_exit() -> ipa_power_exit()
Rename the ipa_clock structure to be ipa_power. Rename all
variables and fields using that structure type "power" rather
than "clock".
Rename the ipa_clock_data structure to be ipa_power_data, and more
broadly, just substitute "power" for "clock" in places that
previously represented things related to the "IPA clock".
Update comments throughout.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use runtime power management autosuspend.
Up until this point, we only suspended the IPA hardware for system
suspend; now we'll suspend it aggressively using runtime power
management, setting the initial autosuspend delay to half a second
of inactivity.
Replace pm_runtime_put() calls with pm_runtime_put_autosuspend(),
call pm_runtime_mark_last_busy() before each of those. In places
where we're shutting things down, or decrementing power references
for errors, use pm_runtime_put_noidle() instead.
Finally, remove ipa_runtime_idle(), so the ->runtime_suspend
callback will occur if idle.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array addr on the stack but instead it
static const. Makes the object code smaller by 79 bytes:
Before:
text data bss dec hex filename
176015 54652 128 230795 3858b .../broadcom/brcm80211/brcmsmac/main.o
After:
text data bss dec hex filename
175872 54716 128 230716 3853c .../broadcom/brcm80211/brcmsmac/main.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819125552.8888-1-colin.king@canonical.com
The rtw_pci_init_rx_ring function is only ever called with a fixed
constant or RTK_MAX_RX_DESC_NUM for the "len" argument. Since this
constant is defined as 512, the "if (len > TRX_BD_IDX_MASK)" check
can never happen (TRX_BD_IDX_MASK is defined as GENMASK(11, 0) or in
other words as 4095).
So, remove this check.
The true motivation for this patch is to silence a false Coverity
warning.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210731163546.10753-1-len.baker@gmx.com
Current flow will lead to null ptr access because of trying
to get the size of freed probe-request packets. We store the
information of packet size into rsvd page instead and also fix
the size error issue, which will cause unstable behavoir of
sending probe request by wow firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-6-pkshih@realtek.com
After waking up from WoWLAN, call ieee80211_report_wowlan_wakeup
function call to report wakeup reason to userspace via nl80211.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-5-pkshih@realtek.com
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
The original setting of rsvd pages is compilcated and lead to
error for connecting to AP after resuming from pno mode.
We refine the setting based on different firmware and the link state
to avoid it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-3-pkshih@realtek.com
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
We find the power sequence of system suspend flow don't meet
the criteria when using 8822CE-VR chip by rfe-type 6, because the
reference clock form host is sometimes late. To avoid the behavoir,
we keep CLKREQ# signal to low during suspend to make sure the reference
clock arrival in time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727100503.31626-1-pkshih@realtek.com
Finetune parameter for firmware.
Previous mode neglects environment impacts and could lead to
performance downgrade in some cases.
This new mode makes fw adapts better under noisy environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-3-pkshih@realtek.com
Enabling this improves tx performance for long distance transmission.
We used to enable stbc by the rx stbc cap of the associated station.
But rx cap will be masked out in ieee80211_ht_cap_ie_to_sta_ht_cap
if we do not declare tx stbc.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-2-pkshih@realtek.com
We find that some disconnect events are related to failure of
tx report, so increase log level to improve debuggability.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-1-pkshih@realtek.com
The TX A-MPDU aggregation is not handled in the driver since the
ieee80211_start_tx_ba_session has never been started properly.
Start and stop the TX BA session by tracking the TX aggregation
status of each TID. Fix the ampdu_action and the tx descriptor
accordingly with the given TID.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804151325.86600-1-chris.chiu@canonical.com
There will be crazy numbers of interrupts triggered by 8188cu and
8192cu module, around 8000~10000 interrupts per second, on the usb
host controller. Compare with the vendor driver source code, it's
mapping to the configuration CONFIG_USB_INTERRUPT_IN_PIPE and it is
disabled by default.
Since the interrupt transfer is neither used for TX/RX nor H2C
commands. Disable it to avoid the excessive amount of interrupts
for the 8188cu and 8192cu module which I only have for verification.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: reto.schneider@husqvarnagroup.com
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210701163354.118403-1-chris.chiu@canonical.com
Don't populate the arrays wpa_oui and wps_oui on the stack but
instead them static const. Makes the object code smaller by 63 bytes:
Before:
text data bss dec hex filename
29453 5451 64 34968 8898 .../wireless/marvell/mwifiex/sta_ioctl.o
After:
text data bss dec hex filename
29356 5611 64 35031 88d7 ../wireless/marvell/mwifiex/sta_ioctl.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819121651.7566-1-colin.king@canonical.com
There is no case in which the variable cmd_node->cmd_skb has no ->data,
and thus the variable host_cmd is guaranteed to be not NULL. Therefore,
the null-pointer check is redundant and can be dropped.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804020305.29812-1-islituo@gmail.com
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
Don't populate arrays the stack but instead make them static const. Replace
array channel_info with channel_all since it contains the same data as
channel_all. Makes object code smaller by 961 bytes.
Before:
text data bss dec hex filename
128147 44250 1024 173421 2a56d ../realtek/rtlwifi/rtl8192de/phy.o
After
text data bss dec hex filename
127122 44314 1024 172460 2a1ac ../realtek/rtlwifi/rtl8192de/phy.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210803144949.79433-2-colin.king@canonical.com
The variables rtstatus and place are being initialized with a values
that are never read, the initializations are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210803144949.79433-1-colin.king@canonical.com
Return -ENODEV instead of success for unsupported devices.
Fixes: 54fdb318c1 ("rsi: add new device model for 9116")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210816183947.GA2119@kili
This code returns success if the kmemdup() fails, but obviously it
should return -ENOMEM instead.
Fixes: e5a1ecc97e ("rsi: add firmware loading for 9116 device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805103746.GA26417@kili
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Split memcpy() for each address range to help memcpy() correctly reason
about the bounds checking. Avoids the future warning:
In function 'fortify_memcpy_chk',
inlined from 'memcpy_toio' at ./include/asm-generic/io.h:1204:2,
inlined from 'ray_build_header.constprop' at drivers/net/wireless/ray_cs.c:984:3:
./include/linux/fortify-string.h:285:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
285 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819202825.3545692-4-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
libipw_read_qos_param_element() copies a struct libipw_info_element
into a struct libipw_qos_information_element, but is actually wanting to
copy into the larger struct libipw_qos_parameter_info (the contents of
ac_params_record[] is later examined). Refactor the routine to perform
centralized checks, and copy the entire contents directly (since the id
and len members match the elementID and length members):
struct libipw_info_element {
u8 id;
u8 len;
u8 data[];
} __packed;
struct libipw_qos_information_element {
u8 elementID;
u8 length;
u8 qui[QOS_OUI_LEN];
u8 qui_type;
u8 qui_subtype;
u8 version;
u8 ac_info;
} __packed;
struct libipw_qos_parameter_info {
struct libipw_qos_information_element info_element;
u8 reserved;
struct libipw_qos_ac_parameter ac_params_record[QOS_QUEUE_NUM];
} __packed;
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819202825.3545692-2-keescook@chromium.org
Dynamic size calculations (especially multiplication) should not be
performed in memory allocator function arguments due to the risk of them
overflowing. This could lead to values wrapping around and a smaller
allocation being made than the caller was expecting. Using those
allocations could lead to linear overflows of heap memory and other
misbehaviors.
To avoid this scenario, use the struct_size helper.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210717142513.5411-1-len.baker@gmx.com
Add HW and SDIO ids for use with the SparkLan AP6275S
Add the firmware mapping structures for the BRCM43752 chipset.
The 43752 needs some things setup similar to the 43012 chipset.
The WATERMARK shows better performance when initialized to the 4373 value.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812165218.2508258-2-angus@akkea.ca
This puts tasks submitted to the SDIO workqueue at the head of the queue
and runs them immediately. This gets higher RX throughput with the SDIO
bus.
This was originally submitted as [1]. The original author Wright Feng
reports
> throughput result with 43455(11ac) on 1 core 1.6 Ghz platform is
> Without WQ_HIGGPRI TX/RX: 293/301 (mbps)
> With WQ_HIGHPRI TX/RX: 293/321 (mbps)
I tested this with a 43364(11bgn) on a 1 core 800 MHz platform and got
Without WQ_HIGHPRI TX/RX: 16/19 (Mbits/sec)
With WQ_HIGHPRI TX/RX: 24/20 (MBits/sec)
[1] https://lore.kernel.org/linux-wireless/1584604406-15452-4-git-send-email-wright.feng@cypress.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Arend van Spriel <aspriel@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210802170904.3116223-1-sean.anderson@seco.com
A separate firmware is needed for Broadcom 43430 revision 2. This
chip can be found in e.g. certain revisions of Ampak AP6212 wireless
IC. Original firmware file from IC vendor is named
'fw_bcm43436b0.bin', but brcmfmac and also btbcm drivers report chip
id 43430, so requested firmware file name is
'brcmfmac43430b0-sdio.bin' in line with other 43430 revisions.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804231308.576071-1-mike.rudenko@gmail.com
Historically the broadcom wifi chipsets always had enumeration
space containing all core information at same place. However, for
new chipsets the ASIC developers moved away from that given fact.
So we have to accommodate that it can differ per chipset.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1627505434-9544-5-git-send-email-arend.vanspriel@broadcom.com
Newer firmware API require commands to use xtlv format. Add support
for that in the firmware interface layer.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1627505434-9544-4-git-send-email-arend.vanspriel@broadcom.com
Some cores are getting a revision greater that 99 thus messing up
the column alignment in the list of cores. So adding a digit for
the core revision.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1627505434-9544-3-git-send-email-arend.vanspriel@broadcom.com
The function brcmf_chip_tcm_rambase() returns 0 as invalid ram base
address. However, upcoming chips have ram base address starting at
zero so we have to find a more appropriate invalid value to return.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1627505434-9544-2-git-send-email-arend.vanspriel@broadcom.com
The patch that would first try the board-specific firmware
had a bug because the fallback would not be called: the
asynchronous interface is used meaning request_firmware_nowait()
returns 0 immediately.
Harden the firmware loading like this:
- If we cannot build an alt_path (like if no board_type is
specified) just request the first firmware without any
suffix, like in the past.
- If the lookup of a board specific firmware fails, we get
a NULL fw in the async callback, so just try again without
the alt_path from a dedicated brcm_fw_request_done_alt_path
callback.
- Drop the unnecessary prototype of brcm_fw_request_done.
- Added MODULE_FIRMWARE match for per-board SDIO bins, making
userspace tools to pull all the relevant firmware files.
Fixes: 5ff013914c ("brcmfmac: firmware: Allow per-board firmware binaries")
Cc: Stefan Hansson <newbyte@disroot.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210808180510.8753-1-digetx@gmail.com
This reverts commit a955318fe6 ("stmmac: align RX buffers"),
which breaks at least one platform (Nvidia Jetson-X1), causing
packet corruption. This is 100% reproducible, and reverting
the patch results in a working system again.
Given that it is "only" a performance optimisation, let's
return to a known working configuration until we can have a
good understanding of what is happening here.
Fixes: a955318fe6 ("stmmac: align RX buffers")
Cc: Matteo Croce <mcroce@linux.microsoft.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/netdev/871r71azjw.wl-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820183002.457226-1-maz@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Link: https://lore.kernel.org/r/bd3cd19c-b74f-9704-5786-476bf35ab5de@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Replace netif_err() with pci_err() because the netdevice isn't registered
yet, which results in very ugly messages.
Use kmemdup_nul() instead of open-coding it.
Link: https://lore.kernel.org/r/bf5d4ba9-61a9-2bfe-19ec-75472732d74d@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This avoids having to allocate a buffer on the stack, and we don't have to
make any assumptions on VPD size and location of information in VPD.
Link: https://lore.kernel.org/r/e58f1e40-c043-0266-9a0f-e5a7f3f6883c@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213667
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23 ("e1000e: add support for LTR on I217/I218")
Suggested-by: Yee Li <seven.yi.lee@gmail.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch ensures that mcam flows are allocated
before adding or destroying the flows.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9a ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining user of the ipa_clock_{get,put}() interface is
ipa_isr_thread(). Replace calls to ipa_clock_get() there calling
pm_runtime_get_sync() instead. And call pm_runtime_put() there
rather than ipa_clock_put(). Warn if we ever get an error.
With that, we can get rid of ipa_clock_get() and ipa_clock_put().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we open or close the modem network device we need to ensure the
hardware is powered. Replace the callers of ipa_clock_get() found
in ipa_open() and ipa_stop() with calls to pm_runtime_get_sync().
If an error is returned, simply return that error to the caller
(without any error or warning message). This could conceivably
occur if the function was called while the system was suspended,
but that really shouldn't happen. Replace corresponding calls to
ipa_clock_put() with pm_runtime_put() also.
If the modem crashes we also need to ensure the hardware is powered
to recover. If getting power returns an error there's not much we
can do, but at least report the error. (Ideally the remoteproc SSR
code would ensure the AP was not suspended when it sends the
notification, but that is not (yet) the case.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the ipa_clock_get() call in ipa_uc_clock() when taking the
"proxy" clock reference for the microcontroller with a call to
pm_runtime_get_sync(). Replace calls of ipa_clock_put() for the
microcontroller with pm_runtime_put() calls instead.
There is a chance we get an error when taking the microcontroller
power reference. This is an unlikely scenario, where system suspend
is initiated just before we learn the modem is booting. For now
we'll just accept that this could occur, and report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the "modem-init" Device Tree property is present for a platform,
the modem performs early IPA hardware initialization, and signals
this is complete with an "ipa-setup-ready" SMP2P interrupt. This
triggers a call to ipa_setup(), which requires the hardware to be
powered.
Replace the call to ipa_clock_get() in this case with a call to
pm_runtime_get_sync(). And replace the corresponding calls to
ipa_clock_put() with calls to pm_runtime_put() instead.
There is a chance we get an error when taking this power reference.
This is an unlikely scenario, where system suspend is initiated just
before the modem signals it has finished initializing the IPA
hardware. For now we'll just accept that this could occur, and
report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the hardware to be powered starting at the config stage of
initialization when the IPA driver probes. And we need it powered
when the driver is removed, at least until the deconfig stage has
completed.
Replace callers of ipa_clock_get() in ipa_probe() and ipa_exit(),
calling pm_runtime_get_sync() instead. Replace the corresponding
callers of ipa_clock_put(), calling pm_runtime_put() instead.
The only error we expect when getting power would occur when the
system is suspended. The ->probe and ->remove driver callbacks
won't be called when suspended, so issue a WARN() call if an error
is seen getting power.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski pointed out a race condition in ipa_start_xmit() in a
recently-accepted series of patches:
https://lore.kernel.org/netdev/20210812195035.2816276-1-elder@linaro.org/
We are stopping the modem TX queue in that function if the power
state is not active. We restart the TX queue again once hardware
resume is complete.
TX path Power Management
------- ----------------
pm_runtime_get(); no power Start resume
Stop TX queue ...
pm_runtime_put() Resume complete
return NETDEV_TX_BUSY Start TX queue
pm_runtime_get()
Power present, transmit
pm_runtime_put() (auto-suspend)
The issue is that the power management (resume) activity and the
network transmit activity can occur concurrently, and there's a
chance the queue will be stopped *after* it has been started again.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power ...
Resume complete
Start TX queue
Stop TX queue <-- No more transmits after this
pm_runtime_put()
return NETDEV_TX_BUSY
We address this using a STARTED flag to indicate when the TX queue
has been started from the resume path, and a spinlock to make the
flag and queue updates happen atomically.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power Resume complete
start TX queue \
If STARTED flag is *not* set: > atomic
Stop TX queue set STARTED flag /
pm_runtime_put()
return NETDEV_TX_BUSY
A second flag is used to address a different race that involves
another path requesting power.
TX path Other path Power Management
------- ---------- ----------------
pm_runtime_get_sync() Resume
Start TX queue \ atomic
Set STARTED flag /
(do its thing)
pm_runtime_put()
(auto-suspend)
pm_runtime_get() Mark delayed resume
STARTED *is* set, so
do *not* stop TX queue <-- Queue should be stopped here
pm_runtime_put()
return NETDEV_TX_BUSY Suspend done, resume
Resume complete
pm_runtime_get()
Stop TX queue
(STARTED is *not* set) Start TX queue \ atomic
pm_runtime_put() Set STARTED flag /
return NETDEV_TX_BUSY
So a STOPPED flag is set in the transmit path when it has stopped
the TX queue, and this pair of operations is also protected by the
spinlock. The resume path only restarts the TX queue if the STOPPED
flag is set. This case isn't a major problem, but it avoids the
"non-trivial amount of useless work" done by the networking stack
when NETDEV_TX_BUSY is returned.
Fixes: 6b51f802d6 ("net: ipa: ensure hardware has power in ipa_start_xmit()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a mostly cosmetic patch that creates some helpers for accessing
the VLAN table. These helpers are also a bit more careful in that they
do not modify the ocelot->vlan_mask unless the hardware operation
succeeded.
Not all callers check the return value (the init code doesn't), but anyway.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ocelot device trees, like ocelot_pcb123.dts for example,
have SERDES ports (ports 4 and higher) that do not have status = "disabled";
but on the other hand do not have a phy-handle or a fixed-link either.
So from the perspective of phylink, they have broken DT bindings.
Since the blamed commit, probing for the entire switch will fail when
such a device tree binding is encountered on a port. There used to be
this piece of code which skipped ports without a phy-handle:
phy_node = of_parse_phandle(portnp, "phy-handle", 0);
if (!phy_node)
continue;
but now it is gone.
Anyway, fixed-link setups are a thing which should work out of the box
with phylink, so it would not be in the best interest of the driver to
add that check back.
Instead, let's look at what other drivers do. Since commit 86f8b1c01a
("net: dsa: Do not make user port errors fatal"), DSA continues after a
switch port fails to register, and works only with the ports that
succeeded.
We can achieve the same behavior in ocelot by unregistering the devlink
port for ports where ocelot_port_phylink_create() failed (called via
ocelot_probe_port), and clear the bit in devlink_ports_registered for
that port. This will make the next iteration reconsider the port that
failed to probe as an unused port, and re-register a devlink port of
type UNUSED for it. No other cleanup should need to be performed, since
ocelot_probe_port() should be self-contained when it fails.
Fixes: e6e12df625 ("net: mscc: ocelot: convert to phylink")
Reported-and-tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are cases where we would like to continue probing the switch even
if one port has failed to probe. When that happens, we need to
unregister a devlink_port of type DEVLINK_PORT_FLAVOUR_PHYSICAL and
re-register it of type DEVLINK_PORT_FLAVOUR_UNUSED.
This is fine, except when calling devlink_port_attrs_set on a structure
on which devlink_port_register has been previously called, there is a
WARN_ON in devlink_port_attrs_set that devlink_port->devlink must be
NULL.
So don't assume that the memory behind dlp is clean when calling
ocelot_port_devlink_init, just zero-initialize it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when probing returns an error, the netdev is freed but
phylink_disconnect is not called.
Create a common function between the unbind path and the error path,
call it the opposite of dpaa2_switch_probe_port: dpaa2_switch_remove_port,
and call it from both the unbind and the error path.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an ASSERT_RTNL in phylink_disconnect_phy which triggers
whenever dpaa2_switch_port_disconnect_mac is called.
To follow the pattern established by dpaa2_eth_disconnect_mac, take the
rtnl_mutex every time we call dpaa2_switch_port_disconnect_mac.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure speed if loopback is used. read_status is not called for
loopback.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct phy_device contains a pointer to the PHY driver and nearly
everywhere this pointer is used to access the PHY driver. Only
mdio_bus_phy_may_suspend() is still using to_phy_driver() instead of the
PHY driver pointer. Uniform PHY driver access by eliminating
to_phy_driver() use in mdio_bus_phy_may_suspend().
Only phy_bus_match() and phy_probe() are still using to_phy_driver(),
because PHY driver pointer is not available there.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_read_status and various other PHY functions support PHY specific
overriding of driver functions by using a PHY specific pointer to the
PHY driver. Add support of PHY specific override to phy_loopback too.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add frame DMA functionality to the Sparx5 platform.
Ethernet frames can be extracted or injected autonomously to or from the
device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list data
structures in memory are used for injecting or extracting Ethernet frames.
The FDMA generates interrupts when frame extraction or injection is done
and when the linked lists need updating.
The FDMA implements two extraction channels, one per switch core port
towards the VCore CPU system and a total of six injection channels.
Extraction channels are mapped one-to-one to the CPU ports, while injection
channels can be individually assigned to any CPU port.
- FDMA channel 0 through 5 corresponds to CPU port 0 injection direction
FDMA_CH_CFG[channel].CH_INJ_PORT is set to 0.
- FDMA channel 0 through 5 corresponds to CPU port 1 injection direction when
FDMA_CH_CFG[channel].CH_INJ_PORT is set to 1.
- FDMA channel 6 corresponds to CPU port 0 extraction direction.
- FDMA channel 7 corresponds to CPU port 1 extraction direction.
The FDMA implements a strict priority scheme among channels. Extraction
channels are prioritized over injection channels and secondarily channels
with higher channel number are prioritized over channels with lower number.
On the other hand, ports are being served on an equal-bandwidth principle
both on injection and extraction directions. The equal-bandwidth principle
will not force an equal bandwidth. Instead, it ensures that the ports
perform at their best considering the operating conditions.
When more than one injection channel is enabled for injection on the same
CPU port, priority determines which channel can inject data. Ownership
is re-arbitrated on frame boundaries.
The FDMA processes linked lists of DMA Control Block Structures (DCBs). The
DCBs have the same basic structure for both injection and extraction. A DCB
must be placed on a 64-bit word-aligned address in memory. Each DCB has a
per-channel configurable amount of associated data blocks in memory, where
the frame data is stored.
The data blocks that are used by extraction channels must be placed on
64-bit word aligned addresses in memory, and their length must be a
multiple of 128 bytes.
A DCB carries the pointer to the next DCB of the linked list, the INFO word
which holds information for the DCB, and a pair of status word and memory
pointer for every data block that it is associated with.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement eswitch API that allows updating rate groups. If group
pointer is NULL, then move the vport to internal unlimited group zero.
Implement devlink_ops->rate_parent_node_set() callback in the terms of
the new eswitch group update API.
Enable QoS for all group's elements if a group has allocated BW share.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Provide eswitch API to allow controlling group rate limits. Use it to
implement devlink_ops->mlx5_devlink_rate_node_tx_{share|max}_set().
The share rate will create relative bandwidth share on the groups level
while within the group the user can set shared rate on the member vports
of that group and this rate will be relative to the group's share rate.
The group with the highest shared rate will get a BW share of 100 and
the rest of the groups will get a value that reflects the ratio between
their share rate and the maximum share rate.
Example:
Created four rate groups with tx_share limits:
$ devlink port function rate add \
pci/0000:06:00.0/group_1 tx_share 30gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_2 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_3 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_4 tx_share 10gbit
Assuming link speed is 50 Gbit/sec ratio divider will be
50 / (30+20+20+10) = 0.625. Normalized rate values for the groups:
<group_1> 30 * 0.625 = 18.75 Gbit/sec
<group_2> 20 * 0.625 = 12.5 Gbit/sec
<group_3> 20 * 0.625 = 12.5 Gbit/sec
<group_4> 10 * 0.625 = 6.25 Gbit/sec
Rate group with unlimited tx_share rate will receive minimum BW value
(1Mbit/sec) if presented any group with tx_share rate limit. This allow
to not drop all packets in case of heavy traffic.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Extend eswitch API with rate limiting groups:
- Define new struct mlx5_esw_rate_group that is used to hold all
internal group data.
- Implement functions that allow creation, destruction and cleanup of
groups.
- Assign all vports to internal unlimited zero group by default.
This commit lays the groundwork for group rate limiting by implementing
devlink_ops->rate_node_{new|del}() callbacks to support creating and
deleting groups through devlink rate node objects. APIs that allows
setting rates and adding/removing members are implemented in following
patches.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Register devlink rate leaf object for every eswitch vport.
Implement devlink ops that enable setting shared and max tx rates
through devlink API.
Extract common eswitch code from existing tx rate set function that is
accessed through NDO to be reused for the devlink. Values configured
with NDO API are not visible for the devlink API, therefore shouldn't be
used simultaneously.
When normalizing the BW share value, dividing the desired minimum rate
by the common divider results in losing information since the quotient
is rounded down. This has a significant affect on configurations of low
rate where the round down eliminates a large percentage of the total
rate. To improve the formula, round up the division result to make sure
that the BW share is at least the value it was supposed to be and won't
lost a significant amount of the expected value.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Move eswitch QoS related code into dedicated file. Provide eswitch API
to access this code meaning it is isolated and restricted to be used
only by eswitch.c. Exception is legacy NDO vf set rate, which moved to
esw/legacy.c.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Currently the sample offload actions send the encapsulated packet
to software. This commit decapsulates the packet before performing
the sampling and set the tunnel properties on the skb metadata
fields to make the behavior consistent with OVS sFlow.
If decapsulating first, we can't use the same match like before in
default table. So instantiate a post action instance to continue
processing the action list. If HW can preserve reg_c, also use the
post action instance.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently the sample offload actions send the encapsulated packet
to software. sFlow expects tunneled packets to be decapsulated while
having the tunnel properties on the skb metadata fields.
Reuse the functions used by connection tracking to map the outer
header properties to a unique id. The next patch will use that id
to restore the tunnel information of decapsulated packets onto the
skb.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
CONFIG_NET_TC_SKB_EXT controls the SKB extension support for
restoring chain ids. SKB extension is not required for tunnel
restoration.
Remove the CONFIG_NET_TC_SKB_EXT dependency as a pre-step for
using the tunnel restore methods for sample offload use cases.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move post action table management to common library providing
add/del/get API. Refactor the ct action offload to use the common
API.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some tc actions are modeled in hardware using multiple tables
causing a tc action list split. For example, CT action is modeled
by jumping to a ct table which is controlled by nf flowtable.
sFlow jumps in hardware to a sample table, which continues to a
"default table" where it should continue processing the action list.
Multi table actions are modeled in hardware using a unique fte_id.
The fte_id is set before jumping to a table. Split actions continue
to a post-action table where the matched fte_id value continues the
execution the tc action list.
Currently the post-action design is implemented only by the ct
action. Introduce post action infrastructure as a pre-step for
reusing it with the sFlow offload feature. Init and destroy the
common post action table. Refactor the ct offload to use the
common post table infrastructure in the next patch.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
IDR is deprecated. Use xarray instead.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently it is in eswitch attribute. Move it to flow attribute to
reflect the change in previous patch.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Module sample belongs to en/tc instead of esw. Move it and rename
accordingly.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5/esw/sample.c doesn't really need mlx5e_priv object, we can remove
this redundant dependency by passing the eswitch object directly to
the sample object constructor.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent change added error checking messages and failed to remove one
of the previous error checks. There are now two checks on variable err
so the second one is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: a83bdada06 ("octeontx2-af: Add debug messages for failures")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210818130927.33895-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmEeV4ATHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqcnkB/0RSBHy8w48DqTvdTd4ldMiNROc47bb
q/HiTHq9dkNRyNzg1unSYLMEyEmdjmek8PmeZug1UV2kdTRFFawuDmk5lNDI6pFy
GNSEcX8VdN6bqTROXtVxjaHPAm5M5Dx91WmytK810aV6b3asMezEPCNsrerfRt+a
xvVTOAbPGvbb2Fb4e0e4ijDgiBpVD+nqhWcJb9953EayxpU80bfE94TSmRiC5yHo
dEZN73tBr08rjSK69bEHKHg0T92Omig5+kn5sLj9TgXhfdtIUCMPnPwEh+8RY1l8
cUY8zUCoyGGWStbhP+O6lq1yLcjQuliQwCAf6oHPb9DM+TmsUozWt2H5
=xTjF
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.15-20210819' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-5.15-20210819
The first patch is by me, for the mailmap file and maps the email
address of two former ESD employees to a newly created role account.
The next 3 patches are by Oleksij Rempel and add support for GPIO
based switchable CAN bus termination.
The next 3 patches are by Vincent Mailhol. The first one changes the
CAN netlink interface to not bail out if the user switched off
unsupported features. The next one adds Vincent as the maintainer of
the etas_es58x driver and the last one cleans up the documentation of
struct es58x_fd_tx_conf_msg.
The next patch is by me, for the mcp251xfd driver and marks some
instances of struct mcp251xfd_priv as const. Lad Prabhakar contributes
2 patches for the rcar_canfd driver, that add support for RZ/G2L
family.
The next 5 patches target the m_can/tcan45x5 driver. 2 are by me an
fix trivial checkpatch warnings. The remaining 3 patches are by Matt
Kline and improve the performance on the SPI based tcan4x5x chip by
batching FIFO reads and writes.
The last 7 patches are for the c_can driver. Dario Binacchi's patch
converts the DT bindings to yaml, 2 patches by me fix a typo and
rename a macro to properly represent the usage. The last 4 patches are
again by Dario Binacchi and provide a performance improvement for the
TX path by operating the TX mailboxes as a true FIFO.
* tag 'linux-can-next-for-5.15-20210819' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (22 commits)
can: c_can: cache frames to operate as a true FIFO
can: c_can: support tx ring algorithm
can: c_can: exit c_can_do_tx() early if no frames have been sent
can: c_can: remove struct c_can_priv::priv field
can: c_can: rename IF_RX -> IF_NAPI
can: c_can: c_can_do_tx(): fix typo in comment
dt-bindings: net: can: c_can: convert to json-schema
can: m_can: Batch FIFO writes during CAN transmit
can: m_can: Batch FIFO reads during CAN receive
can: m_can: Disable IRQs on FIFO bus errors
can: m_can: fix block comment style
can: tcan4x5x: cdev_to_priv(): remove stray empty line
can: rcar_canfd: Add support for RZ/G2L family
dt-bindings: net: can: renesas,rcar-canfd: Document RZ/G2L SoC
can: mcp251xfd: mark some instances of struct mcp251xfd_priv as const
can: etas_es58x: clean-up documentation of struct es58x_fd_tx_conf_msg
MAINTAINERS: add Vincent MAILHOL as maintainer for the ETAS ES58X CAN/USB driver
can: netlink: allow user to turn off unsupported features
can: dev: provide optional GPIO based termination support
dt-bindings: can: fsl,flexcan: enable termination-* bindings
...
====================
Link: https://lore.kernel.org/r/20210819133913.657715-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.
A sketch of what dpaa2_switch_init does:
dpsw_open
dpaa2_switch_detect_features
dpsw_reset
for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
dpsw_if_disable
dpsw_if_set_stp
dpsw_vlan_remove_if_untagged
dpsw_if_set_tci
dpsw_vlan_remove_if
}
dpsw_vlan_remove
alloc_ordered_workqueue
dpsw_fdb_remove
dpaa2_switch_ctrl_if_setup
When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.
Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.
This will trigger a second error:
[ 93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed
[ 93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13
[ 93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13
Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:
[E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled
So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.
Fixes: 613c0a5810 ("staging: dpaa2-switch: enable the control interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e0 ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported by a comment in the c_can_start_xmit() this was not a FIFO.
C/D_CAN controller sends out the buffers prioritized so that the lowest
buffer number wins.
What did c_can_start_xmit() do if head was less tail in the tx ring ? It
waited until all the frames queued in the FIFO was actually transmitted
by the controller before accepting a new CAN frame to transmit, even if
the FIFO was not full, to ensure that the messages were transmitted in
the order in which they were loaded.
By storing the frames in the FIFO without requiring its transmission, we
will be able to use the full size of the FIFO even in cases such as the
one described above. The transmission interrupt will trigger their
transmission only when all the messages previously loaded but stored in
less priority positions of the buffers have been transmitted.
Link: https://lore.kernel.org/r/20210807130800.5246-5-dariobin@libero.it
Suggested-by: Gianluca Falavigna <gianluca.falavigna@inwind.it>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The algorithm is already used successfully by other CAN drivers
(e.g. mcp251xfd). Its implementation was kindly suggested to me by
Marc Kleine-Budde following a patch I had previously submitted. You can
find every detail at https://lore.kernel.org/patchwork/patch/1422929/.
The idea is that after this patch, it will be easier to patch the driver
to use the message object memory as a true FIFO.
Link: https://lore.kernel.org/r/20210807130800.5246-4-dariobin@libero.it
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The c_can_poll() handles RX/TX events unconditionally. It may therefore
happen that c_can_do_tx() is called unnecessarily because the interrupt
was triggered by the reception of a frame. In these cases, we avoid to
execute unnecessary statements and exit immediately.
Link: https://lore.kernel.org/r/20210807130800.5246-3-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The C_CAN/D_CAN cores implement 2 interfaces to manage the message
objects. To avoid concurrency and the need for locking one interface
is used in the TX path (IF_TX). While the other one, named IF_RX is
used from NAPI context only. As this interface is not only used to
manage RX, but also TX message objects, this patch renames IF_RX to
IF_NAPI.
Link: https://lore.kernel.org/r/20210809080608.171545-1-mkl@pengutronix.de
Cc: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Give FIFO writes the same treatment as reads to avoid fixed costs of
individual transfers on a slow bus (e.g., tcan4x5x).
Link: https://lore.kernel.org/r/20210817050853.14875-4-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On peripherals communicating over a relatively slow SPI line
(e.g. tcan4x5x), individual transfers have high fixed costs.
This causes the driver to spend most of its time waiting between
transfers and severely limits throughput.
Reduce these overheads by reading more than one word at a time.
Writing could get a similar treatment in follow-on commits.
Link: https://lore.kernel.org/r/20210817050853.14875-3-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
[mkl: remove __packed from struct id_and_dlc]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If FIFO reads or writes fail due to the underlying regmap (e.g., SPI)
I/O, propagate that up to the m_can driver, log an error, and disable
interrupts, similar to the mcp251xfd driver.
While reworking the FIFO functions to add this error handling,
add support for bulk reads and writes of multiple registers.
Link: https://lore.kernel.org/r/20210817050853.14875-2-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
[mkl: re-wrap long lines, remove WARN_ON, convert to netdev block comments]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the commenting style in the m_can driver.
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Link: https://lore.kernel.org/r/20210819111703.599686-2-mkl@pengutronix.de
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD block on RZ/G2L SoC is almost identical to one found on
R-Car Gen3 SoC's. On RZ/G2L SoC interrupt sources for each channel
are split into different sources and the IP doesn't divide (1/2)
CANFD clock within the IP.
This patch adds compatible string for RZ/G2L family and splits
the irq handlers to accommodate both RZ/G2L and R-Car Gen3 SoC's.
Link: https://lore.kernel.org/r/20210727133022.634-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
[mkl: fixed typo: recieve -> receive, thanks Geert]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the patch 07ff4aed01 ("time/timecounter: Mark 1st argument of
timecounter_cyc2time() as const") some instances of the struct
mcp251xfd_priv can be marked as const. This patch marks these as
const.
Link: https://lore.kernel.org/r/20210813091027.159379-1-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The documentation of struct es58x_fd_tx_conf_msg explains in details
the different TDC parameters. However, those description are redundant
with the documentation of struct can_tdc.
Remove most of the description.
Also, fixes a typo in the reference to the datasheet (E701 -> E70).
Link: https://lore.kernel.org/r/20210815033248.98111-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sanity checks on the control modes will reject any request related
to an unsupported features, even turning it off.
Example on an interface which does not support CAN-FD:
$ ip link set can0 type can bitrate 500000 fd off
RTNETLINK answers: Operation not supported
This patch lets such command go through (but requests to turn on an
unsupported feature are, of course, still denied).
Link: https://lore.kernel.org/r/20210815033248.98111-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.
This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.
Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Don't populate the array stpa on the stack but instead it
static const. Makes the object code smaller by 81 bytes:
Before:
text data bss dec hex filename
54993 17248 0 72241 11a31 ./drivers/net/ethernet/ti/cpsw_new.o
After:
text data bss dec hex filename
54784 17376 0 72160 119e0 ./drivers/net/ethernet/ti/cpsw_new.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array spec_opcode on the stack but instead it
static const. Makes the object code smaller by 158 bytes:
Before:
text data bss dec hex filename
12271 3976 128 16375 3ff7 .../hisilicon/hns3/hns3pf/hclge_cmd.o
After:
text data bss dec hex filename
12017 4072 128 16217 3f59 .../hisilicon/hns3/hns3pf/hclge_cmd.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array speeds on the stack but instead it
static const. Makes the object code smaller by 17 bytes:
Before:
text data bss dec hex filename
39987 14200 64 54251 d3eb .../huawei/hinic/hinic_sriov.o
After:
text data bss dec hex filename
39906 14264 64 54234 d3da .../huawei/hinic/hinic_sriov.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_ethtool_gset() does not return any errors. Since there are no users
of this function that rely on its return value, it can be
made void.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_ethtool_gset() does not return any errors, so error handling can be
omitted to make code more simple.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register for retrieving TX counters is present only on R-Car Gen3
and RZ/G2L; it is not present on R-Car Gen2.
Add the tx_counters hw feature bit to struct ravb_hw_info, to enable this
feature specifically for R-Car Gen3 now and later extend it to RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports TX and RX clock internal delay modes, whereas R-Car
Gen2 and RZ/G2L do not support it.
Add an internal_delay hw feature bit to struct ravb_hw_info to enable this
only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On R-Car the checksum calculation on RX frames is done by the E-MAC
module, whereas on RZ/G2L it is done by the TOE.
TOE calculates the checksum of received frames from E-MAC and outputs it to
DMAC. TOE also calculates the checksum of transmission frames from DMAC and
outputs it E-MAC.
Add net_features and net_hw_features to struct ravb_hw_info, to support
subsequent SoCs without any code changes in the ravb_probe function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun