Handle asic specific table to hw mappings in
combios_setup_i2c_bus() directly. This allows us
to remove most of the combios quirks and clean up
the i2c bus setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we added i2c buses as needed when enumerating connectors
power management, etc. This only exposed the actual buses used and
could have lead to the same buse getting created more than once if
one buses was used for more than one purpose. This patch sets up
all i2c buses on the card in one place and users of the buses just
point back to the one instance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- buffer offsets in the base regs are 256b aligned so
shift properly when comparing, fixed by Andre Maasikas
- mipmap size was calculated wrong when nlevel=0
- texture bo offsets were used after the bo base address was added
- vertex resource size register is size - 1, not size
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(For some reason I thought that went in ages ago ...)
This fixes support for PCI domains in what should hopefully be a backward
compatible way along with a change to libdrm.
When the interface version is set to 1.4, we assume userspace understands
domains and the world is at peace. We thus pass proper domain numbers
instead of 0 to userspace.
The newer libdrm will then try 1.4 first, and fallback to 1.1, along with
ignoring domains in the later case (well, except on alpha of course)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (27 commits)
drm/nvc0: fix typo in PRAMIN flush
drm/nouveau: Fix DCB TMDS config parsing.
drm/nv30: Fix PFB init for nv31.
drm/nv04: Fix up SGRAM density detection.
drm/i2c/ch7006: Don't use POWER_LEVEL_FULL_POWER_OFF on early chip versions.
drm/nouveau: Init dcb->or on cards that have no usable DCB table.
drm/nouveau: reduce severity of some "error" messages
drm/nvc0: backup bar3 channel on suspend
drm/nouveau: implement init table opcodex 0x5e and 0x9a
drm/nouveau: implement init table op 0x57, INIT_LTIME
drm/nvc0: implement crtc pll setting
drm/nvc0: fix evo dma object so we display something
drm/nvc0: rudimentary instmem support
drm/nvc0: implement memory detection
drm/nvc0: allow INIT_GPIO
drm/nvc0: starting point for GF100 support, everything stubbed
drm/nv30: Workaround dual TMDS brain damage.
drm/nouveau: No need to set slave TV encoder configs explicitly.
drm/nv17-nv4x: Attempt to init some external TMDS transmitters.
drm/nv10: Fix up switching of NV10TCL_DMA_VTXBUF.
...
This hasn't mattered up until the ioctl started using the value, and it fell
apart.
fixes fd.o 29340, Ubuntu LP 606081
[airlied: cleaned up whitespace and don't need an error before pushing]
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes a regression introduced by 58bbb63720c8997e0136fe1884101e7ca40d68fd
(fdo bug 29324).
Reported-by: Johannes Obermayr <johannesobermayr@gmx.de>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need a valid OR value because there're a few nv17 cards with DCB v1.4.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's some known configurations where the lack of these tables/scripts
is perfectly normal, reduce visibilty of complaint messages to debug.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
sil164 and friends are the most common, usually they just need to be
poked once because a fixed configuration is enough for any modes and
clocks, so they worked without this patch if the BIOS had done a good
job on POST. Display couldn't survive a suspend/resume cycle though.
Unfortunately, BIOS scripts are useless here.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not very nice, but I don't think there's a simpler workaround.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Leaving the IRQ unack'ed while switching contexts makes the switch
fail randomly on some nv1x.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_load() just returned directly if there was an error instead of
releasing resources.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously nouveau_mem_reset_agp() was only disabling AGP fast writes
when coming back from suspend. However, the "locked out of the card
because of FW" problem can also be reproduced on init if you
unload/reload nouveau.ko several times. This patch makes the AGP code
reset FW on init.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes it easier to see how this is working, and lets us transfer the
EDID in blocks of 16 bytes.
The primary reason for this change is because debug logs are rather hard
to read with the hundreds of single-byte auxch transactions that occur.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This restricts the use of the big kernel lock to the i830 and i810
device drivers. The three remaining users in common code (open, ioctl
and release) get converted to a new mutex, the drm_global_mutex,
making the locking stricter than the big kernel lock.
This may have a performance impact, but only in those cases that
currently don't use DRM_UNLOCKED flag in the ioctl list and would
benefit from that anyway.
The reason why i810 and i830 cannot use drm_global_mutex in their
mmap functions is a lock-order inversion problem between the current
use of the BKL and mmap_sem in these drivers. Since the BKL has
release-on-sleep semantics, it's harmless but it would cause trouble
if we replace the BKL with a mutex.
Instead, these drivers get their own ioctl wrappers that take the
BKL around every ioctl call and then set their own handlers as
DRM_UNLOCKED.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In most use cases the driver will be using the same static config all
the time: interpreting i2c_board_info::platform_data as the default
config we can can save the GPU driver a redundant set_config() call.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required should we ever attempt to use an io-mapping where
KM_USER0 is verboten, such as inside an IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Userspace (notably xf86-video-{intel,ati}) became confused when
drmSetInterfaceVersion() started returning -EBUSY as they used a second
call (the first done in drmOpen()) to check their master credentials.
Since userspace wants to be able to repeatedly call
drmSetInterfaceVersion() allow them to do so.
v3: Rebase to drm-core-next.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prior to this patch the code was dividing the src_v by the dst_h
and vice versa, rather than src_v/dst_v and src_h/dst_h.
This could lead to problems in the calculation of the display
watermarks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I wrote this for the prime sharing work, but I also noticed other external
non-upstream drivers from a large company carrying a similiar patch, so I
may as well ship it in master.
Signed-off-by: Dave Airlie <airlied@redhat.com>
My fine DisplayPort output was getting ST dithering forever after
having had the LVDS enabled at one point.
Signed-off-by: Eric Anholt <eric@anholt.net>
Alex Deucher