In GCC the sizeof(hdsp_version) is 8 because there is a 2 byte hole at
the end of the struct after ->firmware_rev.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The create_bind_cap_vol_ctl does not create any control indicating
that an inverted dmic is present. Therefore, create multiple
capture volumes in this scenario, so we always have some indication
that the internal mic is inverted.
This happens on the Lenovo Ideapad U310 as well as the Lenovo Yoga 13
(both are based on the CX20590 codec), but the fix is generic and
could be needed for other codecs/machines too.
Thanks to Szymon Acedański for the pointer and a draft patch.
BugLink: https://bugs.launchpad.net/bugs/1239392
BugLink: https://bugs.launchpad.net/bugs/1227491
Reported-by: Szymon Acedański <accek@mimuw.edu.pl>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using the headset mic model will cause the headset mic to be labeled
"headset mic" instead of just "mic".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1227093
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ needs a fixup for the bass speaker pin, which was already
provided via model=asus-mode4.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=841645
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine, DAC on node 0x03 seems to give mono output.
Also, it needs additional patches for headset mic support.
It supports CTIA style headsets only.
Alsa-info available at the bug link below.
Cc: stable@kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1236228
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 3830TG seems requiring GPIO bit 0 as the primary mute
control. When a machine is booted after Windows 8, the GPIO pin is
turned off and it results in the silent output.
This patch adds the manual fixup of GPIO bit 0 for this model.
Reported-by: Christopher <DIDI2002@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add 0x54584e03 ID for TI TLV320AIC27 AC'97 codec according to datasheet:
http://www.ti.com/lit/ds/slas253a/slas253a.pdf
The weird thing is that the chip is physically marked 320AD91.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More thorough testing showed that these verbs were necessary to
improve quality of the internal mic. Patch originally from Realtek.
BugLink: https://bugs.launchpad.net/bugs/1231931
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283 pin control for Line1 default control by hidden register.
Use line1 as internal Mic will not get sound when boost value up.
Set control by verb for hidden register will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=oTEO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.12
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
MacBook 6,1 and 6,2 have a CS4208 codec instead of CS4206/CS4207 on
the former models. Most of functions work fine as is, except for the
silent speaker output. After debugging sessions, it turned out that
the machine needs to set GPIO 0 for the speaker amp.
This patch adds the basic support for CS4208 and the fixup for these
MacBooks. Basically the codec works just with the generic parser.
For re-using the existing GPIO amp code and init/free callbacks, a few
places have been changed so that CS4206/4207-specific codes (errata,
etc) won't hit with CS4208.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite C870 shows interrupt problems occasionally when
certain mixer controls like "Mic Switch" is toggled. This seems
worked around by not using MSI.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=833585
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.
This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
So if port:transcoder reconnection happens during stream playback, the ELDV
unsol event can stil trigger pin's amp unmuting when re-setting up audio
info frame.
- remove reading pin amp status before unmuting for speed-up, since pin amp
should always be unmuted.
- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
power state is also fixed here.
This patch is mostly based on suggestion of David Henningsson.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TX300 has a built-in speaker in the tablet part and in the dock
part, and the tablet speaker is supposed to be unused while the
machine is docked. The current HD-audio driver, however, doesn't
support the dock speaker, partly because BIOS doesn't set up the pin
for the corresponding output.
But, not only the missing pin config, also the missing unsol event
handling is another issue. Otherwise the automatic switching via
dock/undock won't work.
Through debugging sessions, we found out that the dock speaker pin is
NID 0x1b, and it generates an unsol event at docking/undocking, the
docking state can be inquired via the normal pin detection verb.
Also, it's turned out that GPIO 2 is needed as an amp. So, all
materials are ready to cook.
This patch provides the basic dock speaker support with TX300:
- The dock speaker is turned on/off via "Dock Speaker" mixer mute.
- The dock speaker is automatically muted when docked. This is
independently from the mixer mute switch, just like the headphone
auto-mute function.
The implementation is a bit tricky. Since we want to handle it as a
secondary speaker, we set it up a pin as a speaker with a jack
detection. Then, the fixup function registers the own unsol callback
for this pin because the standard automute can't handle the thing like
a "speaker jack". In the own automute hook, we apply the mute of the
tablet speaker in addition by checking the dock state.
Also, the speaker control names are slightly shuffled because the
generic parser doesn't give good names but blindly assumes a bass
speaker as a secondary speaker.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59791
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wbLt
-----END PGP SIGNATURE-----
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.
Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a display codec supports multi-stream transport on the pins, the pin's
device list length and device entries will be exposed to codec proc file.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds flags and routines to get device list & selection info on
a pin.
To support Display Port 1.2 multi-stream transport (MST) over single DP port,
a pin can support multiple devices. Please refer to HD-A spec Document Change
Notificaton HDA040-A.
A display audio codec can set flag "dp_mst" in its patch, indicating its pins
can support MST. But at runtime, a pin may not be multi-streaming capable and
report the device list is empty, depending on Gfx driver configuration.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As reported by kbuild test robot <fengguang.wu@intel.com>:
warning: (SND_ES1968_RADIO && SND_FM801_TEA575X_BOOL) selects RADIO_TEA575X which has unmet direct dependencies (MEDIA_SUPPORT && RADIO_ADAPTERS && VIDEO_V4L2)
That happens because a radio driver is selected, without selecting the
RADIO_ADAPTERS menu.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
Without the dynamic minor assignment, HDMI codec may have less PCM
instances than the number of pins, which eventually leads to Oops.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixing warning message:
sound/pci/rme96.c: In function ‘snd_rme96_resume’:
sound/pci/rme96.c:2418:19: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone automute on this machine triggers annoying pop noises.
It seems that only the first DAC can be used, the secondary DAC always
results in this problem. This patch disables the secondary DAC with
a few additional workarounds.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed ALC283 D3 to D0 and D0 to D3 Headphone pop noise.
The previous fix [c5177c86: ALSA: hda - Fix the noise after suspend on
ALC283 codec] doesn't work sufficiently for some laptops.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without proper power management handling, the first use
of a Digi96/8 anytime after a suspend / resume cycle will
start playback with distortions.
v3: Abort if vmalloc() of suspend buffers fail, but do not
leak memory in that case.
[fixed wrong memory leak fix again -- tiwai]
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch doesn't change functionality, it only improves readability
and fixes a copy&paste error in a comment.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use enum hdspm_ltc_format's fps_30 (corresponds to 4) instead of 30,
Other case branches return 1, 2 or 3 respectively, so 30 obviously is
wrong.
Since SNDRV_HDSPM_IOCTL_GET_LTC had never been working due to a
copy&paste error in hdspm.h, this change doesn't break userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another entry, just use the existing fixup for this machine, too.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If compiled without CONFIG_SND_HDA_I915, the audio driver cannot
request power well. However, if the power well is on for other
reasons, maybe audio can still work. Therefore, do not skip the
card completely if compiled without CONFIG_SND_HDA_I915.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The higher mic boosts (on internal mic) are so noisy they're unusable
in practice.
BugLink: https://bugs.launchpad.net/bugs/1213820
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move tea575x from sound/i2c/other to drivers/media/radio
Includes Kconfig changes by Hans Verkuil.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dan Carpenter