Use a meaningful name for the reference clocks so that it indicates the
function.
Update the OMAP4+ USB Host node as well to be in sync with the changes.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'
Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Be more strict and always fail on clk_get() error.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This should fix the following warning at boot on OMAP5 uEVM
[ 8.783155] WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:883 __clk_enable+0x94/0xa4()
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
usbhs_driver_name is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allows the OMAP HS USB host controller to be specified
via device tree.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PHY reset GPIO handling will be done in the PHY driver
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is because we want to get rid of platform_data usage from probe().
The only information we need is PORT_MODE, and this can be supplied
to us by the user (i.e. omap-usb-host.c).
We also move channel clock management from runtime PM handlers into
omap_tll_enable/disable().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
EHCI driver would need to know the number of ports available
on the platform. We set the nports parameter of platform_data
based on IP version if it was not already provided.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The helper functions omap_usbhs_rev1_hostconfig()
and omap_usbhs_rev2_hostconfig() don't write into
the hostconfig register. Make sure that we write
the return value into the hostconfig register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes the below build warning when driver is built-in.
drivers/mfd/omap-usb-host.c:750:12: warning:
‘usbhs_omap_remove’ defined but not used [-Wunused-function]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
clk_set_parent is expected to fail on OMAP3 platforms. We don't
consider that as fatal so don't spam console.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We split initializing revision 1 and revision 2 into different
functions. Initialization is now done dynamically so that only
the number of ports available on the system are initialized.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The driver does not have an interrupt handler and
we don't really need a spinlock, so get rid of it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Enable the optional HSIC clocks (60MHz and 480MHz) for the ports
that are configured in HSIC mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
All ports have similarly named port clocks so we can
bunch them into a port data structure and use for loop
to enable/disable the clocks.
Dynamically allocate and get clocks based on number of ports
available on the platform
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Both OMAP4 and 5 exhibit the same revision ID in the REVISION register
but they have different number of ports i.e. 2 and 3 respectively.
So we can't rely on REVISION register for number of ports on OMAP5
and depend on platform data (or device tree) instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Use devm_ variants of kzalloc and ioremap. Also clean up error path.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Get rid of the unnecessary missing platform data checks
in runtime_suspend/resume. We are already checking for missing
platform data in probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
For the ehci-omap.c part:
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TLL specific code such as channels clocks enable/disable,
initialization functions are removed from the USBHS core
driver. The hwmod of the usb tll is retrieved and omap device
build is performed to created the platform device for the
usb tll component.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs driver invokes the enable/disable APIs of the
usb tll driver in the runtime resume/suspend callbacks
of the runtime get sync and put sync of the usbhs driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There could be possible race condition where the host dev's
are alloced and added to platform dev just before usbhs_init.
Just move usbhs_init before adding child dev.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the hardcoded magic values for dma mask and use the dma
mask api/macro available.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs core driver does not enable/disable the interface and
functional clocks directly, These clocks are handled by runtime pm,
hence instead of the clock enable/disable, the runtime pm APIS are
used. however,the optional clocks and port clocks are handled by
the usbhs core.
Dependency:
This patch is dependent on this series:
[PATCH 0/5 v13 or latest version] omap: usb: host: Runtime PM preparation
for EHCI and OHCI drivers.
Validation performed:
The global suspend/resume of EHCI and OHCI is validated on
OMAP3430 sdp board with this patch combined with the series:
[PATCH 0/5 v13 or latest version] omap: usb: host: Runtime PM preparation
for EHCI and OHCI drivers.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
device name usbhs clocks are changed from
usbhs-omap.0 to usbhs_omap; this is because
in the hwmod registration the device name is set
as usbhs_omap; The redudant clock nodes are removed.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The patch fixes the build failure:
drivers/mfd/omap-usb-host.c:1034:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1034:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1034:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1040:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1040:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1040:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1045:13: error: 'THIS_MODULE' undeclared
here (not in a function)
drivers/mfd/omap-usb-host.c:1050:15: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1050:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1050:1: warning: type defaults to 'int' in
declaration of 'MODULE_AUTHOR'
drivers/mfd/omap-usb-host.c:1050:15: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1051:14: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1051:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1051:1: warning: type defaults to 'int' in
declaration of 'MODULE_ALIAS'
drivers/mfd/omap-usb-host.c:1051:14: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1052:16: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1052:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1052:1: warning: type defaults to 'int' in
declaration of 'MODULE_LICENSE'
drivers/mfd/omap-usb-host.c:1052:16: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1053:20: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1053:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1053:1: warning: type defaults to 'int' in
declaration of 'MODULE_DESCRIPTION'
drivers/mfd/omap-usb-host.c:1053:20: warning: function declaration isn't
a prototype
make[2]: *** [drivers/mfd/omap-usb-host.o] Error 1
CC fs/proc/namespaces.o
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This code section seems to have been accidentally copy pasted.
It causes incorrect bits to be set up in the TLL_CHANNEL_CONF
register and prevents the TLL mode from working correctly.
Cc: stable@kernel.org
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
usbhs_disable function was invoking clk_enable() instead of
clk_disable(), thus only increasing the clock usage counter and
preventing this particular clock from being ever turned off.
Because of this, the power domain of omap4 the USB Host subsystem
would never reach lower power states.This patch calls clk_disable()
in usbhs_disable function
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This reverts commit 7e6502d577.
Oops are produced during initialization of ehci and ohci
drivers. This is because the run time pm apis are used by
the driver but the corresponding hwmod structures and
initialization is not merged. hence revering back the
commit id 7e6502d577
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reported-by: Luciano Coelho <coelho@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs core driver does not enable/disable the interface and
functional clocks; These clocks are handled by hwmod and runtime pm,
hence insted of the clock enable/disable, the runtime pm APIS are
used. however,the port clocks and tll clocks are handled
by the usbhs core.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. Return proper error if omap_usbhs_alloc_child fails
2. In the case of goto err_ehci, we should call platform_device_unregister(ehci)
instead of platform_device_put(ehci) because we have already added the
platform device to device hierarchy.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Roger Quadros