Commit Graph

447 Commits

Author SHA1 Message Date
Mauro Carvalho Chehab 3190fbee01 [media] em28xx: Only change I2C bus inside em28xx-i2c
There's currently a bug on em28xx-i2c that makes it write the
wrong values to register 06, that controlls the I2C bus speed
and bus.

Fix it to change only the I2C bus flag.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-22 13:19:52 -03:00
Mauro Carvalho Chehab 4159d01bea [media] em28xx: Add ISDB support for c3tech Digital duo
This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-19 15:13:50 -03:00
Frank Schaefer 7f6301d125 [media] em28xx-i2c: relax error check in em28xx_i2c_recv_bytes()
It turned out that some devices return less bytes then requested via i2c when
ALL of the following 3 conditions are met:
- i2c bus B is used
- there was no attempt to write to the specified slave address before
- no device present at the specified slave address
With the current code, this triggers an -EIO error and prints a message to the
system log.
Because it can happen very often during device probing, it is better to ignore
this error and bail out silently after the follwing i2c transaction success
check with -ENODEV.

[mchehab@redhat.com: a small CodingStyle fix]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-18 20:18:29 -03:00
Frank Schaefer 195281d0dc [media] em28xx: set the timestamp type for video and vbi vb2_queues
The em28xx driver obtains the timestamps using function v4l2_get_timestamp(),
which produces a montonic timestamp.
Fixes the warnings appearing in the system log since commit 6aa69f99
"[media] vb2: Add support for non monotonic timestamps"

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-18 20:16:47 -03:00
Mauro Carvalho Chehab aab3125c43 [media] em28xx: add support for registering multiple i2c buses
Register both buses 0 and 1 via I2C API. For now, bus 0 is used
only by eeprom on all known devices. Later patches will be needed
if this changes in the future.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-18 18:56:27 -03:00
Mauro Carvalho Chehab 3aa2b3b9cc [media] em28xx: Add a separate config dir for secondary bus
Prepare to register a separate bus for the second bus.
For now, just add a new field. A latter patch will add the
bits to make it work.
This patch was generated by this script:
perl -e 'while (<>) { if (s/EM2874_I2C_SECONDARY_BUS_SELECT.*\n//) {
	printf "\t\t.def_i2c_bus  = 1,\n"; $found = 1; print $_ } else { if ($found) { s/^\s+// }; $found = 0; print $_; } }' \
drivers/media/usb/em28xx/em28xx-cards.c >a && mv a drivers/media/usb/em28xx/em28xx-cards.c

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-18 18:14:52 -03:00
Mauro Carvalho Chehab c7a45e5b4f [media] em28xx: Prepare to support 2 different I2C buses
Newer em28xx devices have 2 buses. Change the logic to allow
using both buses.
This patch was generated by this small script:
for i in drivers/media/usb/em28xx/*.c; do
	sed 's,->i2c_adap,->i2c_adap[dev->def_i2c_bus],g;s,->i2c_client,->i2c_client[dev->def_i2c_bus],'
done
Of course, em28xx.h needed manual edit.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-18 18:14:15 -03:00
Frank Schaefer a61660185b [media] em28xx: enable tveeprom for device Hauppauge HVR-930C
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:38:05 -03:00
Mauro Carvalho Chehab 385cd33c8d [media] em28xx-dvb: Don't put device in suspend mode at feed stop
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:35:54 -03:00
Frank Schaefer 510e884c1a [media] em28xx: extract the device configuration dataset from eeproms with 16 bit address width
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:29:40 -03:00
Frank Schaefer a217968f91 [media] em28xx: do not store eeprom content permanently
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:23:27 -03:00
Frank Schaefer d832c5b28a [media] em28xx: add helper function for reading data blocks from i2c clients
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:21:34 -03:00
Frank Schaefer 87b52439cf [media] em28xx: add basic support for eeproms with 16 bit address width
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 16:20:51 -03:00
Frank Schaefer 0c28dcc054 [media] em28xx: fix eeprom data endianess
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.

[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 15:53:54 -03:00
Frank Schaefer f55eacbe74 [media] em28xx: do not interpret eeprom content if eeprom key is invalid
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 15:48:58 -03:00
Frank Schaefer d90f067713 [media] em28xx-i2c: also print debug messages at debug level 1
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 15:48:54 -03:00
Frank Schaefer 12d7ce185a [media] em28xx-i2c: replace printk() with the corresponding em28xx macros
Reduces the number of characters/lines, unifies the code and improves readability.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 15:48:47 -03:00
Frank Schaefer d7a80eaa9a [media] em28xx-i2c: get rid of the dprintk2 macro
There is only a single place where the dprintk2 macro is used, so get rid of it.

[mchehab@redhat.com: fix checkpathc.pl complain:
 ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 15:20:14 -03:00
Frank Schaefer 43a20d7910 [media] em28xx: bump driver version to 0.2.0
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:52:50 -03:00
Frank Schaefer d5b6a74691 [media] em28xx: fix spacing and some comments in em28xx.h
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:52:26 -03:00
Frank Schaefer a062b291af [media] em28xx: remove some obsolete function declarations
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:51:50 -03:00
Frank Schaefer 8f8b113a03 [media] em28xx: add image quality bridge controls
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:51:30 -03:00
Frank Schaefer 43a5e08d00 [media] em28xx: introduce #defines for the image quality default settings
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:50:31 -03:00
Frank Schaefer 7960205066 [media] em28xx: remove unused ac97 v4l2_ctrl_handler
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:49:56 -03:00
Frank Schaefer 511ffe920b [media] em28xx: remove unused image quality control functions
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:48:58 -03:00
Frank Schaefer 6c3598e641 [media] em28xx: VIDIOC_ENUM_FRAMESIZES: consider the scaler limits when calculating the minimum frame size
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:43:23 -03:00
Frank Schaefer b837413835 [media] em28xx: add function scale_to_size()
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:42:30 -03:00
Frank Schaefer 6b09a21cbc [media] em28xx: rename function get_scale() to size_to_scale()
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:41:23 -03:00
Frank Schaefer 8168532712 [media] em28xx: introduce #define for maximum supported scaling values (register 0x30-0x33)
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:30:18 -03:00
Frank Schaefer 84e902aa05 [media] em28xx: do not claim VBI support if the device is a camera
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:26:06 -03:00
Frank Schaefer fff459e36f [media] em28xx: make ioctl VIDIOC_DBG_G_CHIP_IDENT available for radio devices
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:25:10 -03:00
Frank Schaefer 35deba32e4 [media] em28xx: make ioctl VIDIOC_DBG_G_CHIP_IDENT available without CONFIG_VIDEO_ADV_DEBUG selected
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:24:46 -03:00
Frank Schaefer eb17cee275 [media] em28xx: remove obsolete device state checks from the ioctl functions
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:21:10 -03:00
Frank Schaefer 7a92de6a4c [media] em28xx: VIDIOC_G_TUNER: remove unneeded setting of tuner type
The tuner type is set by the v4l2-core based on the device type.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:16:46 -03:00
Frank Schaefer aab3461876 [media] em28xx: get rid of duplicate function vidioc_s_fmt_vbi_cap()
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:16:01 -03:00
Frank Schaefer 430101bd8b [media] em28xx: remove ioctl VIDIOC_CROPCAP
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:01:34 -03:00
Frank Schaefer 1fe184a6ac [media] em28xx: make ioctls VIDIOC_G/S_PARM working for VBI devices
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 14:00:28 -03:00
Frank Schaefer 83c8bcce06 [media] em28xx: disable ioctl VIDIOC_S_PARM for VBI devices
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 13:40:09 -03:00
Frank Schaefer 3bc85cce36 [media] em28xx: use v4l2_disable_ioctl() to disable ioctl VIDIOC_S_PARM
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 13:39:47 -03:00
Frank Schaefer c2dcef835e [media] em28xx: use v4l2_disable_ioctl() to disable ioctls VIDIOC_G_AUDIO and VIDIOC_S_AUDIO
Instead of checking the device type and returning -EINVAL inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_G_AUDIO and
VIDIOC_S_AUDIO if the device doesn't support audio.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 13:39:11 -03:00
Frank Schaefer 66df67b764 [media] em28xx: disable tuner related ioctls for video and VBI devices without tuner
Disable the ioctls VIDIOC_G_TUNER, VIDIOC_S_TUNER, VIDIOC_G_FREQUENCY and
VIDIOC_S_FREQUENCY for video and VBI devices without tuner.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 13:36:40 -03:00
Frank Schaefer 6e46daba56 [media] em28xx: use v4l2_disable_ioctl() to disable ioctls VIDIOC_QUERYSTD, VIDIOC_G/S_STD
Instead of checking the device type and returning -ENOTTY inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_QUERYSTD,
VIDIOC_G_STD and VIDIOC_S_STD if the device is a camera.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-04 13:36:02 -03:00
Roland Scheidegger 676fa7d4c9 [media] em28xx: add usb id for terratec h5 rev. 3
Seems to work just the same as older revisions.

Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-13 17:41:49 -02:00
Frank Schaefer 33f6984ece [media] em28xx: fix analog streaming with USB bulk transfers
With the conversion to videobuf2, some unnecessary calls of
em28xx_set_alternate() have been removed. It is now called at analog streaming
start only.
This has unveiled a bug that causes USB bulk transfers to fail with all urbs
having status -EVOERFLOW.
The reason is, that for bulk transfers usb_set_interface() needs to be called
even if the previous alt setting was the same (side note: bulk transfers seem
to work only with alt=0).
While it seems to be NOT necessary for isoc transfers, it's reasonable to just
call usb_set_interface() unconditionally in em28xx_set_alternate().
Also add a comment that explains the issue to prevent regressions in the future.

Cc: stable@vger.kernel.org # for 3.8
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-11 18:17:44 -02:00
Hans Verkuil e6066dba44 [media] [REVIEW] em28xx: fix bytesperline calculation in TRY_FMT
The bytesperline calculation was incorrect: it used the old width instead of
the provided width. Fixed.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-08 17:26:24 -02:00
Frank Schaefer ddf289f98b [media] em28xx: overhaul em28xx_capture_area_set()
- move the bit shifting of width+height values inside the function
- fix the debug message format and output values
- add comment about the size limit (e.g. EM277x supports >2MPix)
- make void, because error checking is incomplete and we never check the
  returned value (we would continue anyway)

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-06 14:20:12 -02:00
Frank Schaefer 9b4539bebb [media] em28xx: input: use common work_struct callback function for IR RC key polling
Remove em28xx_i2c_ir_work() and check the device type in the common callback
function em28xx_ir_work() instead. Simplifies em28xx_ir_start().
Reduces the code size with a minor performance drawback.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:43:16 -02:00
Frank Schaefer 1d968cdaae [media] em28xx: i2c RC devices: minor code size and memory usage optimization
Set up the i2c_client locally in em28xx_i2c_ir_handle_key().

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:42:34 -02:00
Frank Schaefer 450c7dd65b [media] em28xx: fix a comment and a small coding style issue
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:40:02 -02:00
Frank Schaefer 146b7ee638 [media] em28xx: remove unused parameter ir_raw from i2c RC key polling functions
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:39:20 -02:00
Frank Schaefer 768da3dbcf [media] em28xx: get rid of the dependency on module ir-kbd-i2c
We already have the key polling functions and the polling infrastructure in
em28xx-input, so we can easily get rid of the dependency on module ir-kbd-i2c.
For maximum safety, do not touch the key reporting mechanism for those devices.
Code size could be improved further but would have minor peformance impacts.
Tested with device "Terratec Cinergy 200 USB" (EM2800_BOARD_TERRATEC_CINERGY_200)

[mchehab@redhat.com: Fix two checkpatch.pl warnings:
 ERROR: "foo * bar" should be "foo *bar" (line 465)
 WARNING: kfree(NULL) is safe this check is probably not required (line 725)]

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:38:50 -02:00
Frank Schaefer 62ec3f86ff [media] em28xx: remove i2cdprintk() messages
We don't report any key/scan codes or errors inside the key polling functions
for internal IR RC devices, just in the key handling fucntions.
Do the same for external devices.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:38:48 -02:00
Frank Schaefer 59cf17d843 [media] em28xx-input: remove dead code line from em28xx_get_key_em_haup()
Field 'old' of struct IR_i2c is used nowhere in module ir-kbd-i2c.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:38:47 -02:00
Frank Schaefer 0b3966e40c [media] em28xx: add missing IR RC slave address to the list of known i2c devices
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 20:25:23 -02:00
Frank Schaefer 5e8d02bb34 [media] em28xx: fix audio input for TV mode of device Terratec Cinergy 250
Remy Blank reported that audio over USB can be made working for the television
input if .amux is changed from EM28XX_AMUX_LINE_IN to EM28XX_AMUX_VIDEO.
An examination of his devices shows, that it is indeed supplied with an EM202
AC97 audio IC. We also use this setting for the Cinergy 200.
Remy Blank also provided the original version of this patch (many thanks !).
Fixes bug 14126 (see bug report for further device details).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-06 10:45:53 -02:00
Mauro Carvalho Chehab ef85cd9cd5 [media] em28xx: enable DMABUF
Now that it uses videobuf2, em28xx can support DMABUF.

Tested with an HVR-950 on analog mode and a 2gen i5core machine
with an i915 graphics adapter.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-06 00:34:22 -02:00
Mauro Carvalho Chehab 3a799c27b3 [media] em28xx: declare em28xx_stop_streaming as static
That fixes the following warning:
	drivers/media/usb/em28xx/em28xx-video.c:611:5: warning: no previous prototype for 'em28xx_stop_streaming' [-Wmissing-prototypes]

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:32:18 -02:00
Frank Schaefer 90271964c9 [media] em28xx: consider the message length limitation of the i2c adapter when reading the eeprom
EEPROMs are currently read in blocks of 16 bytes, but the em2800 is limited
to 4 bytes per read. All other chip variants support reading of max. 64 bytes
at once (according to the em258x datasheet; also verified with em2710, em2882,
and em28174).
Since em2800_i2c_recv_bytes() has been fixed to return with -EOPNOTSUPP when
more than 4 bytes are requested, EEPROM reading with this chip is broken.
It was actually broken before that change, too, it just didn't throw an error
because the i2c adapter silently returned trash data (for all reads >1 byte !).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:19:11 -02:00
Frank Schaefer 45f04e82d0 [media] em28xx: fix+improve+unify i2c error handling, debug messages and code comments
- do not pass USB specific error codes to userspace/i2c-subsystem
- unify the returned error codes and make them compliant with
  the i2c subsystem spec
- check number of actually transferred bytes (via USB) everywehere
- fix/improve debug messages
- improve code comments

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:18:25 -02:00
Frank Schaefer eaf33c404c [media] em28xx: fix the i2c adapter functionality flags
I2C_FUNC_SMBUS_EMUL includes flag I2C_FUNC_SMBUS_WRITE_BLOCK_DATA which signals
that up to 31 data bytes can be written to the ic2 client.
But the EM2800 supports only i2c messages with max. 4 data bytes.
I2C_FUNC_IC2 should be set if a master_xfer function pointer is provided in
struct i2c_algorithm.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:16:54 -02:00
Frank Schaefer 2fcc82d883 [media] em28xx: fix two severe bugs in function em2800_i2c_recv_bytes()
Function em2800_i2c_recv_bytes() has 2 severe bugs:
1) It does not wait for the i2c read to complete before reading the received message content from the bridge registers.
2) Reading more than 1 byte doesn't work
The former can result in data corruption, the latter always does.
The rewritten code also superseds the content of function
em2800_i2c_check_for_device().
Tested with device "Terratec Cinergy 200 USB".

[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:16:01 -02:00
Frank Schaefer f5ae371aca [media] em28xx: respect the message size constraints for i2c transfers
The em2800 can transfer up to 4 bytes per i2c message.
All other em25xx/em27xx/28xx chips can transfer at least 64 bytes per message.
I2C adapters should never split messages transferred via the I2C subsystem
into multiple message transfers, because the result will almost always NOT be
the same as when the whole data is transferred to the I2C client in a single
message.
If the message size exceeds the capabilities of the I2C adapter, -EOPNOTSUPP
should be returned.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:13:29 -02:00
Frank Schaefer 6ea887efad [media] em28xx: IR RC: move assignment of get_key functions from *_change_protocol() functions to em28xx_ir_init()
The get_key functions are independent from the selected protocol, so assign
them once only at device initialization.

[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:12:11 -02:00
Frank Schaefer 05fe2175cf [media] em28xx: refactor the code in em28xx_usb_disconnect()
The main purpose of this patch is to move the call of em28xx_release_resources()
after the call of em28xx_close_extension().
This is necessary, because some resources might be needed/used by the extensions
fini() functions when they get closed.
Also mark the device as disconnected earlier in this function and unify the
em28xx_uninit_usb_xfer() calls for analog and digital mode.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:10:13 -02:00
Frank Schaefer 2665c2995d [media] em28xx: simplify device state tracking
DEV_INITIALIZED of enum em28xx_dev_state state is used nowhere and there is no
need for DEV_MISCONFIGURED, so remove this enum and use a boolean field
'disconnected' in the device struct instead.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:09:39 -02:00
Devin Heitmueller d3829fadc4 [media] em28xx: convert to videobuf2
This patch converts the em28xx driver over to videobuf2.  It is
likely that em28xx_fh can go away entirely, but that will come in
a separate patch.

[mchehab@redhat.com: fix a non-trivial merge conflict with some VBI
 patches; CodingStyle fixes]

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 01:03:38 -02:00
Hans Verkuil 2a221d34b6 [media] em28xx: zero vbi_format reserved array and add try_vbi_fmt
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:58:44 -02:00
Hans Verkuil 1d179eeedc [media] em28xx: remove sliced VBI support
The sliced VBI support in the tvp5150 is completely broken. And there is no
support for the saa7115 sliced VBI implementation in the em28xx driver. So
we remove the sliced VBI support completely.
It should be possible to get it to work with the tvp5150, but that will
require someone to really dig into that driver.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:57:50 -02:00
Hans Verkuil d8c95c08ef [media] em28xx: std fixes: don't implement in webcam mode, and fix std changes
When in webcam mode the STD API shouldn't be implemented.
When changing the standard the resolution wasn't updated, and there was no
check against streaming-in-progress.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:56:38 -02:00
Hans Verkuil 86ff7f1d4b [media] em28xx: fill in readbuffers and fix incorrect return code
g/s_parm should fill in readbuffers.
For non-webcams s_parm should return -ENOTTY instead of -EINVAL.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:52:36 -02:00
Hans Verkuil 50fdf40f69 [media] em28xx: add support for control events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:51:52 -02:00
Hans Verkuil 69a61642ac [media] em28xx: convert to v4l2_fh, fix priority handling
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:51:28 -02:00
Hans Verkuil 081b945ed7 [media] em28xx: convert to the control framework
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:51:05 -02:00
Hans Verkuil 20deebfe17 [media] em28xx: fix tuner/frequency handling
v4l2-compliance found problems with frequency clamping that wasn't
reported correctly and missing tuner index checks.
Also removed unnecessary tuner type checks (these are now done by the
v4l2 core).

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:47:41 -02:00
Hans Verkuil 319a55fbe4 [media] em28xx: fix VIDIOC_DBG_G_CHIP_IDENT compliance errors
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:47:10 -02:00
Hans Verkuil dd5a436322 [media] em28xx: remove bogus input/audio ioctls for the radio device
Radio devices should not implement those ioctls.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:46:50 -02:00
Hans Verkuil a9d79fe581 [media] em28xx: fix querycap
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-05 00:45:43 -02:00
Mauro Carvalho Chehab 3ac693c40a [media] em28xx: tell ir-kbd-i2c that WinTV uses an RC5 protocol
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-04 19:13:24 -02:00
Mauro Carvalho Chehab d40580e7c0 [media] em28xx: simplify IR names on I2C devices
The ir-i2c-kbd already adds I2C IR before the name. The way it is,
the devices are named as:
	"i2c IR (i2c IR (EM2840 Hauppaug"
With is ugly and incorrect. After this patch, it is now properly
displayed as:
	"i2c IR (WinTV USB2)"

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-04 19:13:19 -02:00
Mauro Carvalho Chehab 728f9778e2 [media] em28xx: autoload em28xx-rc if the device has an I2C IR
If the device has an I2C IR, em28xx-rc should be loaded by default,
except if the user explicitly requested to not load, via modprobe
option.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-04 19:13:14 -02:00
Mauro Carvalho Chehab 8303dc9952 [media] em28xx: initialize button/I2C IR earlier
The em28xx-input is used by 3 different types of input devices:
	- devices with buttons (like cameras and grabber devices);
	- devices with I2C remotes;
	- em2860 or latter chips with RC support embedded.
When the device has an I2C remote, all it needs to do is to call
the proper I2C driver (ir-i2c-kbd), passing the proper data to
it, and just leave the code.
Also, button devices have its own init code that doesn't depend on
having an IR or not (as a general rule, they don't have).
So, move its init code to fix bugs introduced by earlier patches
that prevent them to work.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-04 19:13:07 -02:00
Frank Schaefer 7e5d74ee11 [media] em28xx: rename module parameter prefer_bulk to usb_xfer_mode
Since we have now 3 modes (auto/isoc/bulk), usb_xfer_mode is more suitable than prefer_bulk.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-27 19:40:38 -02:00
Mauro Carvalho Chehab 8b2aea7878 [media] em28xx: prefer bulk mode on webcams
Using bulk mode allows more than one webcam, as the maximum fps
is low at 640x480 resolution. So, prefer it, if the device is
a webcam.

Tested with Silvercrest 1.3 Mpixel webcam (em2710) on both bulk and isoc
modes.

Tested analog with HVR-950 model 65201/A1C0 (em2883), where only ISOC
endpoints are available for both DVB and Analog.

Tested on Hauppauge WinTV USB 2 (em2840) on both bulk and isoc modes.

It should be noticed that enabling bulk mode by default with TV boards
is a bad idea; what happens is that, while with ISOC the USB logic will
prevent the concurrent usage of two devices that spends more than 100%
of the USB2 traffic, it doesn't care with bulk transfers.

On my tests, I started two streams, one with a WinTV at 640x480x30fps
and the other one with a Silvercrest webcam at 640x480, on a lower fps)
both on bulk mode. One of the streams always silently failed.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-23 17:24:30 -02:00
Mauro Carvalho Chehab a3efa1cc0e [media] em28xx: make the logs reflect the specific chip name
In order to make easier to analize the logs when multiple devices
are plugged, change the device name accordingly with the chip
version.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-23 16:54:34 -02:00
Mauro Carvalho Chehab aa51496b21 [media] em28xx: display the isoc/bulk mode
As both bulk and isoc modes can be available, display what it
was found for both DVB and analog.

While here, also displays if audio is provided via USB Audio
Class or via vendor's extension.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-23 14:35:25 -02:00
Mauro Carvalho Chehab b5cff595bd [media] em28xx: prefer_bulk parameter is read-only
As the bulk mode is set at device's probe, it is not possible
to change it later. So, change the parameter to be read only
after modprobing.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-23 13:14:20 -02:00
Frank Schaefer a6bad040da [media] em28xx: clean up the data type mess of the i2c transfer function parameters
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 21:48:29 -02:00
Frank Schaefer 36016a351d [media] em28xx: clean up and unify functions em28xx_copy_vbi() em28xx_copy_video()
The code in em28xx_vbi_copy can be simplified a lot.
Also rename some variables to something more meaningful and fix+add the
function descriptions.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 21:09:45 -02:00
Frank Schaefer 227b7c9067 [media] em28xx: move the em2710/em2750/em28xx specific frame data processing code to a separate function
em28xx_urb_data_copy() actually consists of two parts:
USB urb processing (checks, data extraction) and frame data packet processing.
Move the latter to a separate function and call it from em28xx_urb_data_copy()
for each data packet.
The em25xx, em2760, em2765 (and likely em277x) chip variants are using a
different frame data format, for which support will be added later with
another function.
This reduces the size of em28xx_urb_data_copy() and makes the code much more
readable. While we're at it, clean up the code a bit (rename some variables to
something more meaningful, improve some comments etc.)

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:57:17 -02:00
Frank Schaefer e04c00d985 [media] em28xx: em28xx_urb_data_copy(): move duplicate code for capture_type=0 and capture_type=2 to a function
Reduce code duplication by moving the duplicate code for dev->capture_type=0
(vbi start) and dev->capture_type=2 (video start) to a function.
The same function will also be called by the (not yet existing) em25xx frame
data processing code.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:55:48 -02:00
Frank Schaefer 4078d625c9 [media] em28xx: move caching of pointer to vmalloc memory in videobuf to struct em28xx_buffer
In the current code em28xx_urb_data_copy() caches the pointer to the vmalloc
memory in videobuf locally.
The alternative would be to call videobuf_to_vmalloc() for each processed USB
data packet (isoc USB transfers => 64 times per URB) in the em28xx_copy_*()
functions.
With the next commits, the data processing code will be split into functions
for serveral reasons:
- em28xx_urb_data_copy() is generally way to long, making it less readable
- there is code duplication between VBI and video data processing
- support for em25xx data processing (uses a different header and frame
  end signaling mechanism) will be added
This would require extensive usage of pointer-pointers, which usually makes the
code less readable and prone to bugs.
The better solution is to cache the pointer in struct em28xx_buffer.
This also improves consistency, because we already track the buffer fill count there.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:55:01 -02:00
Frank Schaefer a48370158d [media] em28xx: refactor VBI data processing code in em28xx_urb_data_copy()
When a new frame header is detected in em28xx_urb_data_copy() and the data
packet contains both, VBI data and video data, the prevoius VBI buffer doesn't
get finished and is overwritten with the new VBI data.
This bug is not triggered with isochronous USB transfers, because the data
packetes are much smaller than the VBI data size.
But when using USB bulk transfers, the whole data of an URB is treated as
single packet, which is usually much larger then the VBI data size.
Refactor the VBI data processing code to fix this bug, but also to simplify the
code and make it similar to the video data processing code part (which allows
further code abstraction/unification in the future).
The changes have been tested with device "Hauppauge HVR-900".

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:53:43 -02:00
Frank Schaefer 8732533b32 [media] em28xx: move field 'pos' from struct em28xx_dmaqueue to struct em28xx_buffer
This field is used to keep track of the current memory position in the buffer,
not in the dma queue, so move it to right place.
This also allows us to get rid of the struct em28xx_dmaqueue pointer parameter
in functions em28xx_copy_video() and em28xx_copy_vbi().

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:52:28 -02:00
Frank Schaefer cbe7f8a030 [media] em28xx: remove obsolete field 'frame' from struct em28xx_buffer
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:51:19 -02:00
Frank Schaefer 948a49aa69 [media] em28xx: use common function for video and vbi buffer completion
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:50:59 -02:00
Frank Schaefer 24a6d8497f [media] em28xx: refactor get_next_buf() and use it for vbi data, too
get_next_buf() and vbi_get_next_buf() do exactly the same just with a
different dma queue and buffer. Saving the new buffer pointer back to the
device struct in em28xx_urb_data_copy() instead of doing this from inside
these functions makes it possible to get rid of one of them.
Also refactor the function parameters and return type:
- pass a pointer to struct em28xx as parameter (instead of obtaining the
  pointer from the dma queue pointer with the container_of macro) like we do
  it in all other functions
- instead of using a pointer-pointer, return the pointer to the new buffer
  as return value of the function

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 20:48:57 -02:00
Frank Schaefer 960da93ba5 [media] em28xx: use common urb data copying function for vbi and non-vbi data streams
em28xx_urb_data_copy_vbi() is actually an extended version of
em28xx_urb_data_copy(). With the preceding fixes and improvements, it works
fine with both, vbi and non-vbi data streams without performance impacts.
So rename em28xx_urb_data_copy_vbi() to em28xx_urb_data_copy(), delete the
the old implementation of em28xx_urb_data_copy() and change the code to use
this function for both data stream types.
Tested with "SilverCrest 1.3 MPix webcam" (progressive, non-vbi) and
"Hauppauge HVR-900 (65008/A1C0)" (interlaced, vbi enabled and disabled).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 19:17:37 -02:00
Frank Schaefer 79ff8697e9 [media] em28xx: em28xx_urb_data_copy_vbi(): calculate vbi_size only if needed
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 19:17:18 -02:00
Frank Schaefer 0455eebfbd [media] em28xx: fix capture type setting in em28xx_urb_data_copy_vbi()
Set capture type to 1 (video start) when the video frame start header is
detected. This bug didn't cause any trouble, because this type of header is
never received in vbi mode.
Fix it, because we want to use this function with disabled vbi in the future.
Also start with capture type -1 to avoid processing of corrupted/incomplete
frame data which is usually received at streaming start (especially when
USB bulk transfers are used).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 19:16:57 -02:00
Frank Schaefer 3610f58bb1 [media] em28xx: make sure the packet size is >= 4 before checking for headers in em28xx_urb_data_copy_vbi()
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 19:16:10 -02:00
Frank Schaefer b77e0c088f [media] em28xx: fix video data start position calculation in em28xx_urb_data_copy_vbi()
The header check/removal code at the end of function em28xx_urb_data_copy_vbi()
is obsolete, because this is already done earlier in this function.
In fact it is incomplete (doesn't check for vbi header) and causes trouble
when the first data bytes are the same as header bytes (which is fortunately
very unlikely).

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 19:02:32 -02:00
Frank Schaefer 454fe92f01 [media] em28xx: add module parameter for selection of the preferred USB transfer type
By default, isoc transfers are used if possible.
With the new module parameter, bulk can be selected as the
preferred USB transfer type.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:20:03 -02:00
Frank Schaefer c647a91a25 [media] em28xx: improve USB endpoint logic, also use bulk transfers
The current enpoint logic ignores all bulk endpoints and uses
a fixed mapping between endpint addresses and the supported
data stream types (analog/audio/DVB):
  Ep 0x82, isoc	=> analog
  Ep 0x83, isoc	=> audio
  Ep 0x84, isoc	=> DVB
Now that the code can also do bulk transfers, the endpoint
logic has to be extended to also consider bulk endpoints.
The new logic preserves backwards compatibility and reflects
the endpoint configurations we have seen so far:
  Ep 0x82, isoc		=> analog
  Ep 0x82, bulk		=> analog
  Ep 0x83, isoc*	=> audio
  Ep 0x84, isoc		=> digital
  Ep 0x84, bulk		=> analog or digital**
 (*: audio should always be isoc)
 (**: analog, if ep 0x82 is isoc, otherwise digital)

[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:17:52 -02:00
Frank Schaefer c8e9d95b41 [media] em28xx: set USB alternate settings for analog video bulk transfers properly
Extend function em28xx_set_alternate:
- use alternate setting 0 for bulk transfers as default
- respect module parameter 'alt'=0 for bulk transfers
- set max_packet_size to 512 bytes for bulk transfers
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:13:11 -02:00
Frank Schaefer 7312f2c9fa [media] em28xx: add fields for analog and DVB USB transfer type selection to struct em28xx
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:11:42 -02:00
Frank Schaefer 0cf544a6cc [media] em28xx: rename some USB parameter fields in struct em28xx to clarify their role
Also improve the comments.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:11:26 -02:00
Frank Schaefer a950e4a75e [media] em28xx: rename function em28xx_dvb_isoc_copy and extend for USB bulk transfers
The URB data processing for DVB bulk transfers is very similar to
what is done with isoc transfers, so create a common function that
works with both transfer types based on the existing isoc function.
Tested with device Hauppauge HVR-930c.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:04:50 -02:00
Frank Schaefer 4601cc3977 [media] em28xx: rename function em28xx_isoc_copy_vbi and extend for USB bulk transfers
The URB data processing for bulk transfers is very similar to what
is done with isoc transfers, so create a common function that works
with both transfer types based on the existing isoc function.

[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:04:28 -02:00
Frank Schaefer 0fa4a40290 [media] em28xx: rename function em28xx_isoc_copy and extend for USB bulk transfers
The URB data processing for bulk transfers is very similar to what
is done with isoc transfers, so create a common function that works
with both transfer types based on the existing isoc function.

[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:02:48 -02:00
Frank Schaefer 1653cb0cb2 [media] em28xx: remove double checks for urb->status == -ENOENT in urb_data_copy functions
This check is already done in the URB handler
em28xx_irq_callback before calling these functions.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:00:59 -02:00
Frank Schaefer 337fe8dad5 [media] em28xx: clear USB halt/stall condition in em28xx_init_usb_xfer when using bulk transfers
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 18:00:30 -02:00
Frank Schaefer 057ca0da06 [media] em28xx: create a common function for isoc and bulk USB transfer initialization
- rename em28xx_init_isoc to em28xx_init_usb_xfer
- add parameter for isoc/bulk transfer selection which is passed to em28xx_alloc_urbs
- rename local variable isoc_buf to usb_bufs

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:58:14 -02:00
Frank Schaefer 6ddd89d0c9 [media] em28xx: create a common function for isoc and bulk URB allocation and setup
Rename the existing function for isoc transfers em28xx_init_isoc
to em28xx_init_usb_xfer and extend it.
URB allocation and setup is now done depending on the USB
transfer type, which is selected with a new function parameter.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:58:00 -02:00
Frank Schaefer afb177e065 [media] em28xx: rename function em28xx_uninit_isoc to em28xx_uninit_usb_xfer
This function will be used to uninitialize USB bulk transfers, too.
Also rename the local variable isoc_bufs to usb_bufs.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:57:41 -02:00
Frank Schaefer 836e93bf6a [media] em28xx: update description of em28xx_irq_callback
em28xx_irq_callback can be used for isoc and bulk transfers.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:57:27 -02:00
Frank Schaefer 89f84b9c20 [media] em28xx: remove obsolete #define EM28XX_URB_TIMEOUT
It isn't used anymore and uses constants which no longer exist.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:57:00 -02:00
Frank Schaefer 74209dc06a [media] em28xx: rename struct em28xx_usb_isoc_ctl to em28xx_usb_ctl
Also rename the corresponding field isoc_ctl in struct em28xx
to usb_ctl.
We will use this struct for USB bulk transfers, too.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:56:49 -02:00
Frank Schaefer f0fa9936f5 [media] em28xx: rename struct em28xx_usb_isoc_bufs to em28xx_usb_bufs
It will be used for USB bulk transfers, too.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:56:34 -02:00
Frank Schaefer 515688a898 [media] em28xx: rename isoc packet number constants and parameters
Rename EM28XX_NUM_PACKETS to EM28XX_NUM_ISOC_PACKETS and
EM28XX_DVB_MAX_PACKETS to EM28XX_DVB_NUM_ISOC_PACKETS to
clarify that these values are used only for isoc usb transfers.
Also use the term num_packets instead of max_packets, as this
is how these values are used and called in struct urb.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:56:10 -02:00
Frank Schaefer 8c3015676f [media] em28xx: clarify meaning of field 'progressive' in struct em28xx
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:55:58 -02:00
Frank Schaefer c02ec71b01 [media] em28xx: fix wrong data offset for non-interlaced mode in em28xx_copy_video
em28xx_copy_video uses a wrong offset for the target buffer
when copying the data from an USB isoc packet. This happens
only for the second and all following lines in the packet.
The reason why this bug doesn't cause image corruption with
my test device (SilverCrest Webcam 1.3 MPix) is, that this
device never sends any packets that cross the end of a line.
I don't know if all devices behave like this, so this patch
should be considered for stable.
With the upcoming patches to add support for USB bulk transfers,
em28xx_copy_video will be called once per URB, which will
always trigger this bug.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 17:55:34 -02:00
Frank Schaefer 2f5741aa6a [media] em28xx: input: fix oops on device removal
When em28xx_ir_init() fails due to an configuration error, it frees the memory
of struct em28xx_IR *ir, but doesn't set the corresponding pointer in the
device struct to NULL.
On device removal, em28xx_ir_fini() gets called, which then calls
rc_unregister_device() with a pointer to freed memory.
Fixes bug 26572 (http://bugzilla.kernel.org/show_bug.cgi?id=26572)

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-22 16:14:37 -02:00
Mauro Carvalho Chehab 0dae883923 [media] em28xx: add support for RC6 mode 0 on devices that support it
Newer em28xx chipsets (em2874 and upper) are capable of supporting
RC6 codes, on both mode 0 (command mode, 16 bits payload size, similar
to RC5, also called "Philips mode") and mode 6a (OEM command mode,
with offers a few alternatives with regards to the payload size).
I don't have any mode 6a control ATM to test it, so, I opted to add
support only to mode 0.
After this patch, adding support to mode 6a should not be hard.
Tested with a Philips television remote controller.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 21:16:19 -02:00
Mauro Carvalho Chehab 105e3687ad [media] em28xx: add support for NEC proto variants on em2874 and upper
By disabling the NEC parity check, it is possible to handle all 3 NEC
protocol variants (32, 24 or 16 bits).
Change the driver in order to handle all of them.
Unfortunately, em2860/em2863 provide only 16 bits for the IR scancode,
even when NEC parity is disabled. So, this change should affect only
em2874 and newer devices, with provides up to 32 bits for the scancode.
Tested with one NEC-16, one NEC-24 and one RC5 IR.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 21:15:52 -02:00
Mauro Carvalho Chehab 37285bf2a5 em28xx: add two missing tuners at the Kconfig file
Those two tuners may also be needed.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 21:14:41 -02:00
Jonathan McDowell fc09931e10 [media] Autoselect more relevant frontends for EM28XX DVB stick
I noticed that the EM28XX DVB driver doesn't auto select all of the
appropriate DVB tuner modules required. In particular I needed
DVB_LGDT3305 for my a340, but it looks like DVB_MT352 + DVB_S5H1409 were
missing as well.

Signed-Off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 21:14:01 -02:00
Michael Krufky 41f55d5755 [media] tda10071: make sure both tuner and demod i2c addresses are specified
display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 14:36:54 -02:00
Sakari Ailus 8e6057b510 [media] v4l: Convert drivers to use monotonic timestamps
Convert drivers using wall clock time (CLOCK_REALTIME) to timestamp from the
monotonic timer (CLOCK_MONOTONIC).

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-12-21 10:56:43 -02:00
Mauro Carvalho Chehab d3e4ea017a [media] em28xx-cards: fix a warning
drivers/media/usb/em28xx/em28xx-cards.c:3309:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-28 07:38:56 -02:00
David Härdeman c003ab1bed [media] rc-core: add separate defines for protocol bitmaps and numbers
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.

Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.

Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.

Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).

The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).

This patch separate the different usages in preparation for
upcoming patches.

Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.

The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.

Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-27 11:49:51 -02:00
Martin Blumenstingl 890401364d [media] em28xx: Better support for the Terratec Cinergy HTC USB XS
This intializes the card just like the windows driver does

- the "HTC USB XS HD" uses the same firmware as the "HTC Stick HD";
- both have different GPIO and reg init sequences;

Tested only with DVB-C.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-25 11:25:16 -02:00
Mauro Carvalho Chehab bf3b202b41 Merge branch 'staging/for_v3.7' into v4l_for_linus
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.

* staging/for_v3.7: (109 commits)
  [media] m5mols: Add missing #include <linux/sizes.h>
  [media] stk1160: Add support for S-Video input
  Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
  [media]  dvb: LNA implementation changes
  [media] v4l2-ioctl: fix W=1 warnings
  [media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
  [media] omap3isp: Fix compilation error in ispreg.h
  [media] rc-msi-digivox-ii: Add full scan keycodes
  [media] cx25821: testing the wrong variable
  [media] tda18271-common: hold the I2C adapter during write transfers
  [media] ds3000: add module parameter to force firmware upload
  [media] drivers/media: Remove unnecessary semicolon
  [media] winbond: remove space from driver name
  [media] iguanair: cannot send data from the stack
  [media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
  [media] dvb-usb: print small buffers via %*ph
  [media] uvc: Add return code check at vb2_queue_init()
  [media] em28xx: Replace memcpy with struct assignment
  [media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
  [media] mem2mem_testdev: Use devm_kzalloc() in probe
  ...
2012-10-11 15:07:19 -03:00
Antti Palosaari 33eebec55c [media] dvb: LNA implementation changes
* use dvb property cache
* implement get (thus API minor++)
* PCTV 290e: 1=LNA ON, all the other values LNA OFF
  Also fix PCTV 290e LNA comment, it is disabled by default
Hans and Mauro proposed use of cache implementation of get as they
were planning to extend LNA usage for analog side too.

Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-07 10:27:49 -03:00
Linus Torvalds 0b8e74c6f4 Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
 "The first part of the media updates for Kernel 3.7.

  This series contain:

   - A major tree renaming patch series: now, drivers are organized
     internally by their used bus, instead of by V4L2 and/or DVB API,
     providing a cleaner driver location for hybrid drivers that
     implement both APIs, and allowing to cleanup the Kconfig items and
     make them more intuitive for the end user;

   - Media Kernel developers are typically very lazy with their duties
     of keeping the MAINTAINERS entries for their drivers updated.  As
     now the tree is more organized, we're doing an effort to add/update
     those entries for the drivers that aren't currently orphan;

   - Several DVB USB drivers got moved to a new DVB USB v2 core; the new
     core fixes several bugs (as the existing one that got bitroted).
     Now, suspend/resume finally started to work fine (at least with
     some devices - we should expect more work with regards to it);

   - added multistream support for DVB-T2, and unified the API for
     DVB-S2 and ISDB-S.  Backward binary support is preserved;

   - as usual, a few new drivers, some V4L2 core improvements and lots
     of drivers improvements and fixes.

  There are some points to notice on this series:

   1) you should expect a trivial merge conflict on your tree, with the
      removal of Documentation/feature-removal-schedule.txt: this series
      would be adding two additional entries there.  I opted to not
      rebase it due to this recent change;

   2) With regards to the PCTV 520e udev-related breakage, I opted to
      fix it in a way that the patches can be backported to 3.5 even
      without your firmware fix patch.  This way, Greg doesn't need to
      rush backporting your patch (as there are still the firmware cache
      and firmware path customization issues to be addressed there).

      I'll send later a patch (likely after the end of the merge window)
      reverting the rest of the DRX-K async firmware request, fully
      restoring its original behaviour to allow media drivers to
      initialize everything serialized as before for 3.7 and upper.

   3) I'm planning to work on this weekend to test the DMABUF patches
      for V4L2.  The patches are on my queue for several Kernel cycles,
      but, up to now, there is/was no way to test the series locally.

      I have some concerns about this particular changeset with regards
      to security issues, and with regards to the replacement of the old
      VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
      GPU drivers change.  The Overlay API allows direct PCI2PCI
      transfers from a media capture card into the GPU framebuffer, but
      its API is crappy.  Also, the only existing X11 driver that
      implements it requires a XV extension that is not available
      anymore on modern drivers.  The DMABUF can do the same thing, but
      with it is promising to be a properly-designed API.  If I can
      successfully test this series and be happy with it, I should be
      asking you to pull them next week."

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
  em28xx: regression fix: use DRX-K sync firmware requests on em28xx
  drxk: allow loading firmware synchrousnously
  em28xx: Make all em28xx extensions to be initialized asynchronously
  [media] tda18271: properly report read errors in tda18271_get_id
  [media] tda18271: delay IR & RF calibration until init() if delay_cal is set
  [media] MAINTAINERS: add Michael Krufky as tda827x maintainer
  [media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
  [media] MAINTAINERS: add Michael Krufky as cxusb maintainer
  [media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
  [media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
  [media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
  [media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
  [media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
  [media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
  [media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
  [media] exynos-gsc: Add missing static storage class specifiers
  [media] exynos-gsc: Remove <linux/version.h> header file inclusion
  [media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
  [media] s5p-tv: Fix potential NULL pointer dereference error
  [media] s5k6aa: Fix possible NULL pointer dereference
  ...
2012-10-07 17:49:05 +09:00
Ezequiel Garcia e0f6e4d6ff [media] em28xx: Replace memcpy with struct assignment
This kind of memcpy() is error-prone and its
replacement with a struct assignment is prefered.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-06 12:23:15 -03:00
Mauro Carvalho Chehab 2425bb3d40 em28xx: regression fix: use DRX-K sync firmware requests on em28xx
As em28xx-dvb will always be initialized asynchronously, there's
no need anymore for a separate thread to load the DRX-K firmware.

Fixes a known regression with kernel 3.6 with tda18271 driver
and asynchronous DRX-K firmware load.

Antti tested it with the following hardware:
        Hauppauge WinTV HVR 930C
        MaxMedia UB425-TC
        PCTV QuatroStick nano (520e)

Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org #	for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-02 17:15:22 -03:00
Mauro Carvalho Chehab 6ae5e06084 em28xx: Make all em28xx extensions to be initialized asynchronously
em28xx-dvb, em28xx-alsa and em28xx-ir are typically initialized
asyncrhronously. The exception for it is when those modules
are loaded before em28xx (or before an em28xx card insertion) or
when they're built in.

Make the extentions to always load asynchronously. That allows
having all DVB firmwares loaded synchronously with udev-182.

Antti tested it with the following hardware:
	Hauppauge WinTV HVR 930C
	MaxMedia UB425-TC
	PCTV QuatroStick nano (520e)

Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-02 17:11:33 -03:00
Antti Palosaari 0c42a55c86 [media] em28xx: do not set PCTV 290e LNA handler if fe attach fail
It was a bug that could cause oops if demodulator attach was
failed.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-01 17:07:06 -03:00
Antti Palosaari a36a66d7aa [media] cxd2820r: use static GPIO config when GPIOLIB is undefined
It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-01 17:07:05 -03:00
Antti Palosaari 13a5336e88 [media] em28xx: implement FE set_lna() callback
Make LNA run-time switching possible for PCTV nanoStick T2 290e!

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-10-01 17:07:05 -03:00
Antti Palosaari 1e8f31f317 [media] cxd2820r: use Kernel GPIO for GPIO access
Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-09-27 14:33:58 -03:00
Hans Verkuil 0e8025b9f6 [media] v4l2: make vidioc_s_audio const
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_audio.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-09-26 10:50:12 -03:00
Mauro Carvalho Chehab fccea74ff8 [media] Kconfig: merge all customise options into just one
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.

That simplifies the life for users, as they can just keep
this untouched.

Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-21 08:05:06 -03:00
Mauro Carvalho Chehab 88f8472c9f [media] Fix some Makefile rules
On a few places, := were using instead of +=, causing drivers to
not compile.

While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.

Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-16 19:55:03 -03:00
Dan Carpenter e36c92fd63 [media] em28xx: use after free in em28xx_v4l2_close()
We need to move the unlock before the kfree(dev);

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-15 18:49:00 -03:00
Mauro Carvalho Chehab cb7a01ac32 [media] move i2c files into drivers/media/i2c
Move ancillary I2C drivers into drivers/media/i2c, in order to
better organize them.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-15 16:42:14 -03:00
Mauro Carvalho Chehab 0c0d06cac6 [media] rename most media/video usb drivers to media/usb
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-15 16:25:07 -03:00