The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When implementing the test_iqr() method, I forgot that this driver is not an
ordinary PCI driver and also needs to support VLB variant of the chip. Moreover,
'hwif->dev' should be NULL, potentially causing oops in pci_read_config_byte().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a second step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, except one printk() which can
easily be replaced by a dev_info()/dev_warn() call.
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-usb@vger.kernel.org
Acked-by: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes the bad hashes for one Kingston and one Transcend card.
Thanks to komuro for pointing this out.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver takes into account not only the interrupt status bit but
also "FIFO empty" bit in its test_irq() method. This actually is a
superfluous check since for the DMA commands calling the
dma_test_irq() method further in the interrupt handler makes sure FIFO
is emptied.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit e0321fbe6d (pdc202xx_old:
implement test_irq() method (take 2)) I forgot to modify
'pdc2026x_port_ops'... :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds idstrings for Kingston 1GB/4GB and Transcend 4GB/8GB.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This enables shared IRQs and other features to be used with platform devices
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide: Fix IDE taskfile with cfq scheduler
ide: Must hold queue lock when requeueing
ide: Requeue request after DMA timeout
When ide taskfile access is being used (for example with hdparm --security
commands) and cfq scheduler is selected, the scheduler crashes on BUG in
cfq_put_request.
The reason is that the cfq scheduler is tracking counts of read and write
requests separately; the ide-taskfile subsystem allocates a read request and
then flips the flag to make it a write request. The counters in cfq will
mismatch.
This patch changes ide-taskfile to allocate the READ or WRITE request as
required and don't change the flag later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-atapi requeues requests without holding the queue lock.
This patch fixes it by using ide_requeue_and_plug.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that my KVM virtual machines were experiencing IDE
issues resulting in processes stuck on waiting for buffers to
complete.
The root cause is of course race conditions in the ancient qemu
backend that I'm using. However, the fact that the guest isn't
recovering is a bug.
I've tracked it down to the change made last year to dequeue
requests at the start rather than at the end in the IDE layer.
commit 8f6205cd57
Author: Tejun Heo <tj@kernel.org>
Date: Fri May 8 11:53:59 2009 +0900
ide: dequeue in-flight request
The problem is that the function ide_dma_timeout_retry does not
requeue the current request, causing one request to be lost for
each DMA timeout.
This patch fixes this by requeueing the request.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This reverts commit a20b2a44ec.
As requested by David Fries. This makes CDROMs which are slave drives
on a ribbon without a master disappear and causes other similar kinds
of badness.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6: (49 commits)
drivers/ide: Fix continuation line formats
ide: fixed section mismatch warning in cmd640.c
ide: ide_timing_compute() fixup
ide: make ide_get_best_pio_mode() static
via82cxxx: use ->pio_mode value to determine pair device speed
tx493xide: use ->pio_mode value to determine pair device speed
siimage: use ->pio_mode value to determine pair device speed
palm_bk3710: use ->pio_mode value to determine pair device speed
it821x: use ->pio_mode value to determine pair device speed
cs5536: use ->pio_mode value to determine pair device speed
cs5535: use ->pio_mode value to determine pair device speed
cmd64x: fix handling of address setup timings
amd74xx: use ->pio_mode value to determine pair device speed
alim15x3: fix handling of UDMA enable bit
alim15x3: fix handling of DMA timings
alim15x3: fix handling of command timings
alim15x3: fix handling of address setup timings
ide-timings: use ->pio_mode value to determine fastest PIO speed
ide: change ->set_dma_mode method parameters
ide: change ->set_pio_mode method parameters
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
XFER_SW_DMA_0 mode should be excluded from the extended cycle
timing computations.
[ This is just a documentation fix -- code inside the affected
'if' block already makes sure to accept only PIO modes. ]
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for the requirements of the DMA mode currently used.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear UDMA enable bit also for PIO modes.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop depending on the BIOS setup.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop depending on the BIOS setup.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for the requirements of the other device on the port.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
to determine the fastest allowed PIO for shared PIO/DMA timings.
Affected host drivers: amd74xx and via82cxxx.
[ Update comment to match -DaveM ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ->set_dma_mode method parameters to match ->set_dmamode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ->set_pio_mode method parameters to match ->set_piomode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dma_mode field to ide_drive_t matching dma_mode field used in
struct ata_device.
The validity of the field is restricted to ->dma_pio_mode method
only currently in IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pio_mode field to ide_drive_t matching pio_mode field used in
struct ata_device.
The validity of the field is restricted to ->set_pio_mode method
only currently in IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* preserve 80-wire cable detection bit
* don't clear UDMA settings when programming PIO/MWDMA modes
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commits 5955c7a and 7d948b1 for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit e4d866c for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add custom struct ide_tp_ops instance to fix the internal bug of some VIA
chipsets which will reset the device register after changing the nIEN bit
in the device control register.
Based on commit bfce5e0 for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VIA_SATA_PATA flag for cx700, vx800 and vx855 chipsets
(the first port is SATA).
Based on commits 7585eb1, bfce5e0 and e4d866c for pata_via
host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit e4d866c for pata_via host driver
(PCI ID was later changed by commit 5993856).
Update my credits while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove dead OSB4 UDMA support
* remove unreachable code
* make isa_dev local to ->init_chipset
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO timings. This fixes many issues with the open-coded version
like using 16-bit timings when 8-bit ones should be used or not
accounting for the enhanced cycle time specified by the device.
Based on libata pata_cypress host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO and MWDMA timings. This fixes some issues with the open-coded
version like allowing faster MWDMA timings than the ones required
by the current PIO mode or not accounting for the enhanced MWDMA
cycle time specified by the device.
Based on libata pata_cmd64x host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on libata pata_amd host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove leftover local_irq_[save,restore]() and FIXME note.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO timings. This fixes many issues with the open-coded version
like potential recovery timings underclocking or not accounting
for the enhanced cycle time specified by the device.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide_detach() called first ide_release() and then release_region(). This
produced the following warnings:
Trying to free nonexistent resource <000000000000c10e-000000000000c10e>
Trying to free nonexistent resource <000000000000c100-000000000000c107>
This is true, because the callchain inside ide_release() is:
ide_release -> pcmcia_disable_device -> pcmcia_release_io
So, the whole io-block is already gone for release_region(). To fix
this, just swap the order of releasing (and remove the now obsolete
shadowing).
bzolnier:
- release resources in ide_release() to fix ordering of events
- remove stale FIXME note while at it
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ready to get everything using unlocked_ioctl()
For ide_tape we just push down as this is legacy code anyway
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, Jan 03, 2010 at 12:23:14AM +0000, Russell King wrote:
> - with IDE
> - locks the interrupt line, and makes the machine extremely painful -
> about an hour to get to the point of being able to unload the
> pdc202xx_old module.
Having manually bisected kernel versions, I've narrowed it down to some
change between 2.6.30 and 2.6.31. There's not much which has changed
between the two kernels, but one change stands out like a sore thumb:
+static int pdc202xx_test_irq(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long high_16 = pci_resource_start(dev, 4);
+ u8 sc1d = inb(high_16 + 0x1d);
+
+ if (hwif->channel) {
+ /*
+ * bit 7: error, bit 6: interrupting,
+ * bit 5: FIFO full, bit 4: FIFO empty
+ */
+ return ((sc1d & 0x50) == 0x40) ? 1 : 0;
+ } else {
+ /*
+ * bit 3: error, bit 2: interrupting,
+ * bit 1: FIFO full, bit 0: FIFO empty
+ */
+ return ((sc1d & 0x05) == 0x04) ? 1 : 0;
+ }
+}
Reading the (documented as a 32-bit) system control register when the
interface is idle gives: 0x01da110c
So, the byte at 0x1d is 0x11, which is documented as meaning that the
primary and secondary FIFOs are empty.
The code above, which is trying to see whether an IRQ is pending, checks
for the IRQ bit to be one, and the FIFO bit to be zero - or in English,
to be non-empty.
Since during a BM-DMA read, the FIFOs will naturally be drained to the
PCI bus, the chance of us getting to the interface before this happens
are extremely small - and if we don't, it means we decide not to service
the interrupt. Hence, the screaming interrupt problem with drivers/ide.
Fix this by only indicating an interrupt is ready if both the interrupt
and FIFO empty bits are at '1'.
This bug only affects PDC20246/PDC20247 (Promise Ultra33) based cards,
and has been tested on 2.6.31 and 2.6.33-rc2.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back ->maskproc method since it is still needed for proper operation,
as noticed by Russell King:
> This change is bogus.
>
> writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
> readb(base + ICS_ARCIN_V6_INTROFFSET_2);
>
> writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
> readb(base + ICS_ARCIN_V6_INTROFFSET_1);
>
> This sequence of code does:
>
> 1. enable interrupt 1
> 2. disable interrupt 2
> 3. enable interrupt 2
> 4. disable interrupt 1
>
> which results in the interrupt for the second channel being enabled -
> leaving channel 1 blocked.
>
> Firstly, icside shares its two IDE channels with one DMA engine - so it's
> a simplex interface. IDE supports those (or did when the code was written)
> serializing requests between the two interfaces. libata does not.
>
> Secondly, the interrupt lines on icside float when there's no drive connected
> or when the drive has its NIEN bit set, which means that you get spurious
> screaming interrupts which can kill off all expansion card interrupts on
> the machine unless you disable the channel interrupt on the card.
>
> Since libata can not serialize the operation of the two channels like IDE
> can, the libata version of the icside driver does not contain the interrupt
> stearing logic. Instead, it looks at the status after reset, and if
> nothing was found on that channel, it masks the interrupt from that
> channel.
This patch reverts changes done in commit dff8817 (I became confused due to
non-standard & undocumented ->maskproc method, anyway sorry about that).
Noticed-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
scc_pata host driver predated module unloading support for IDE host
drivers so even though it supports PCI hot-unplug and implements
PCI device ->remove method it doesn't allow module removal. Fix it.
Add missing __init/__exit tags to module_init/module_exit functions
while at it (from Peter Huewe).
Noticed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
sl82c105: remove no longer needed debugging code
sis5513: remove stale TODO
pdc202xx_old: remove no longer needed debugging code
cy82c693: remove no longer needed debugging code
cmd64x: remove no longer needed debugging code
alim15x3: remove obsolete and dangerous wdc_udma parameter
ide: Increase WAIT_DRQ to accomodate some CF cards and SSD drives.
cs5535: add pci id for AMD based CS5535 controllers
slc90e66: fix UDMA handling
drivers/ide/tx4938ide.c: use resource_size()
drivers/ide/ide_platform.c: use resource_size()
drivers/ide/au1xxx-ide.c: use resource_size()
hpt366: remove dead old timing tables
ide: update Kconfig text to mark as deprecated
ide-tape: remove the BKL
hpt366: kill unused #define's
The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on commit 02cb009 for pata_cs5530.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checking of the currently programmed UDMA mode.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Currently, ide_cmd_ioctl when invoked for setting DMA transfer mode calls
ide_find_dma_mode with requested mode as XFER_UDMA_6. This prevents setting DMA
mode to any other value than the default (maximum) supported by the device (or
UDMA6, if supported) irrespective of the actual requested transfer mode and
returns error.
For example, setting mode to UDMA2 using hdparm, where UDMA4 is the default
transfer mode gives following error:
# ./hdparm -d1 -Xudma2 /dev/hda
/dev/hda:hda: UDMA/66 mode selected
setting using_dma to 1 (on)
hda: UDMA/66 mode selected
setting xfermode to 66 (UltraDMA mode2)
HDIO_DRIVE_CMD(setxfermode) failed: Invalid argument
using_dma = 1 (on)
This patch fixes the issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_request_mem_region.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_{ioremap/io_port_map}.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for {request/release}_mem_region and ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been enough time since introduction of the new timing tables
(commit 809b53c from Dec 12 2007) and the old timing tables are still
available in pata_hpt37x.c (or git history) if somebody needs them.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-cs.c is the only PCMCIA device driver making use of CONFIG_PCMCIA_DEBUG,
so convert it to use the dynamic debug infrastructure.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This reverts commit 6029336426.
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Kconfig text for CONFIG_IDE doesn't give a hint to users that this
subsystem is currently in maintenance mode and isn't actively developed.
Let's correct this by marking it as deprecated, and also get rid of a bunch of
unnecessary text that doesn't really have anything to do with what the option is
for.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the BKL calls in the chrdev_{open,release} interfaces with a
simple sleeping mutex.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two have been long unused but I've just noticed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
Revert "Revert "ide: try to use PIO Mode 0 during probe if possible""
sis5513: fix PIO setup for ATAPI devices
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.
This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 6029336426).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6029336426.
Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
ide: fixup for fujitsu disk
ide: convert to ->proc_fops
at91_ide: remove headers specific for at91sam9263
IDE: palm_bk3710: convert clock usage after clkdev conversion
ide: fix races in handling of user-space SET XFER commands
ide: allow ide_dev_read_id() to be called from the IRQ context
ide: ide-taskfile.c fix style problems
drivers/ide/ide-cd.c: Use DIV_ROUND_CLOSEST
ide-tape: fix handling of postponed rqs
ide-tape: convert to ide_debug_log macro
ide-tape: fix debug call
ide: Fix annoying warning in ide_pio_bytes().
IDE: Save a call to PageHighMem()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
...
->read_proc, ->write_proc are going away, ->proc_fops should be used instead.
The only tricky place is IDENTIFY handling: if for some reason
taskfile_lib_get_identify() fails, buffer _is_ changed and at least
first byte is overwritten. Emulate old behaviour with returning
that first byte to userspace and reporting length=1 despite overall -E.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver requires only static memory controller definitions and macroses
contained in generic header at91sam9_smc.h.
Those extra headers are misleading since this driver also works fine for
at91sam9260 SoC: tests were performed on afeb9260 board.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Make cmd->tf_flags field 'u16' and add IDE_TFLAG_SET_XFER taskfile flag.
* Update ide_finish_cmd() to set xfer / re-read id if the new flag is set.
* Convert set_xfer_rate() (write handler for /proc/ide/hd?/current_speed)
and ide_cmd_ioctl() (HDIO_DRIVE_CMD ioctl handler) to use the new flag.
* Remove no longer needed disable_irq_nosync() + enable_irq() from
ide_config_drive_speed().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Un-static __ide_wait_stat().
* Allow ide_dev_read_id() helper to be called from the IRQ context by
adding irq_ctx flag and using mdelay()/__ide_wait_stat() when needed.
* Switch ide_driveid_update() to set irq_ctx flag.
This change is needed for the consecutive patch which fixes races in
handling of user-space SET XFER commands but for improved bisectability
and clarity it is better to do it in a separate patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix trivial style problems:
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: space prohibited between function name and open parenthesis '('
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
ERROR: do not use C99 // comments X 2
ERROR: trailing statements should be on next line
ERROR: trailing whitespace
ERROR: switch and case should be at the same indent
WARNING: line over 80 characters
total: 5 errors, 4 warnings
Also removed dead code
Also used pr_err() to avoid line breaks
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-tape used to hit
[ 58.614854] ide-tape: ht0: BUG: Two DSC requests queued!
due to the fact that another rq was being issued while the driver was
waiting for DSC to get set for the device executing ATAPI commands which
set the DSC to 1 to indicate completion.
Here's a sample output of that case:
issue REZERO_UNIT
[ 143.088505] ide-tape: ide_tape_issue_pc: retry #0, cmd: 0x01
[ 143.095122] ide: Enter ide_pc_intr - interrupt handler
[ 143.096118] ide: Packet command completed, 0 bytes transferred
[ 143.106319] ide-tape: ide_tape_callback: cmd: 0x1, dsc: 1, err: 0
[ 143.112601] ide-tape: idetape_postpone_request: cmd: 0x1, dsc_poll_freq: 2000
we stall the ide-tape queue here waiting for DSC
[ 143.119936] ide-tape: ide_tape_read_position: enter
[ 145.119019] ide-tape: idetape_do_request: sector: 4294967295, nr_sectors: 0
and issue the new READ_POSITION rq and hit the check.
[ 145.126247] ide-tape: ht0: BUG: Two DSC requests queued!
[ 145.131748] ide-tape: ide_tape_read_position: BOP - No
[ 145.137059] ide-tape: ide_tape_read_position: EOP - No
Also, ->postponed_rq used to point to that postponed request. To make
things worse, in certain circumstances the rq it was pointing to got
replaced unterneath it by swiftly reusing the same rq from the mempool
of the block layer practically confusing stuff even more.
However, we don't need to keep a pointer to that rq but simply wait for
DSC to be set first before issuing the follow-up request in the drive's
queue. In order to do that, we make idetape_do_request() first check the
DSC and if not set, we stall the drive queue giving the other device on
that IDE channel a chance.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove tape->debug_mask and use drive->debug_mask instead.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error only occurs when IDETAPE_DEBUG_LOG is enabled.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC can't see that flags is only set and used when PageHighmem() is
true.
Inspired by a patch from Jean Delvare.
Signed-off-by: David S. Miller <davem@davemloft.net>
PageHighMem() isn't cheap so avoid calling it twice on the same page.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't leak kernel stack information through uninitialized structure members.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory
leak after writing lots of data, the kmalloc-96 slab cache keeps
growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush
is never kfreed.
Commit a09485df9c ("ide: move request
type specific code from ide_end_drive_cmd() to callers (v3)") and
f505d49ffd ("ide: fix barriers support")
cause this regression, cmd->rq must now be set for ide_complete_cmd to
honor the IDE_TFLAG_DYN flag.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory overrun in function ide_get_identity_ioctl() which
chooses the size of a memory buffer depending on the ioctl command that led
to the function call, however, passes that buffer to a function which needs the
buffer size to be always chosen unconditionally.
Due to conditional compilation the memory overrun can only happen on big endian
machines. The error can be triggered using ioctl HDIO_OBSOLETE_IDENTITY. Usage
of ioctl HDIO_GET_IDENTITY is safe.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2f0d0fd2a6 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.
Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).
While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some devices in the wild that clear the DRQ bit during the
last word of a packet command and therefore could use a "second chance"
for that last word of data to be xferred instead of simply failing the
request. Do that by attempting to suck in those last bytes in PIO mode.
In addition, the ATA_ERR bit has to be cleared for we cannot be sure the
data is valid otherwise.
See http://bugzilla.kernel.org/show_bug.cgi?id=13399 for details.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_kill_rq()
and ide_floppy_do_request() for failed requests.
[ bugfix part ]
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_do_devset()
and ide_complete_drive_reset(). Then remove ide_rq_bytes().
[ cleanup part ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such requests should be failed with -EIO (like all other requests
in this function) instead of being completed successfully.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 86ccf37c6a the driver was modified
to deal with the removal of the pciirq argument to ide_pci_setup_ports().
But in the conversion only the first port's IRQ gets setup.
Inspired by a patch by Bartlomiej Zolnierkiewicz., and with help from
Alan Cox.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hwif->rq point to PM request during PM sequence and do not allow
any other types of requests to slip in (the old comment was never correct
as there should be no such requests generated during PM sequence).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some broken devices that report multiple DMA xfer modes
enabled at once (ATA spec doesn't allow it) but otherwise work fine
with DMA so just delete ide_id_dma_bug().
[ As discovered by detective work by Frans and Bart, due to how
handling of the ID block was handled before commit c419993
("ide-iops: only clear DMA words on setting DMA mode") this
check was always seeing zeros in the fields or other similar
garbage. Therefore this check wasn't actually checking anything.
Now that the tests actually check the real bits, all we see are
devices that trigger the check yet work perfectly fine, therefore
killing this useless check is the best thing to do. -DaveM ]
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the error gets repeated too frequently, for example each
time HAL polls the device when a disc is present. Avoid that by using
printk_once instead of printk.
Also join the error and corrective action messages into a single line.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frans Pop reported that his CDROM drive reports a blocksize of 2352,
and this causes new warnings due to commit
e8e7b9eb11 ("ide-cd: fix oops when using
growisofs").
What we're trying to do is make sure that "blocklen >> SECTOR_BITS"
is something the block layer won't choke on.
And for Frans' case "2352 >> SECTOR_BITS" is equal to
"2048 >> SECTOR_BITS", and thats "4".
So warning in this case gives no real benefit.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ide_host_enable_irqs() helper and use it in ide_host_register()
before registering ports. Then remove no longer needed IRQ unmasking
from in init_irq().
This should fix the problem with "screaming" shared IRQ on the first
port (after request_irq() call while we have the unexpected IRQ pending
on the second port) which was uncovered by my rework of the serialized
interfaces support.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This begins to fix regressions reported by Frans Pop on his Ultra-10.
There are still some funnies left that we are investigating.
Signed-off-by: David S. Miller <davem@davemloft.net>
With 2.6.30, the error handling code in cdrom_newpc_intr was changed
to deal with partial request failures by normally completing the 'good'
parts of a request and only 'error' the last (and presumably,
incompletely transferred) bio associated with a particular
request. In order to do this, ide_complete_rq is called over
ide_cd_error_cmd() to partially complete the rq. The block layer
does partial completion only for requests with bio's and if the
rq doesn't have one (eg 'GPCMD_READ_DISC_INFO') the request is
completed as a whole and the drive->hwif->rq pointer set to NULL
afterwards. When calling ide_complete_rq again to report
the error, this null pointer is derefenced, resulting in a kernel
crash.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13399.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-ide@vger.kernel.org
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unsupported requests should be never handed down to device drivers
and the best thing we can do upon discovering such request inside
driver's ->do_request method is to just BUG().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ide_drive_t 'drive_data' field from 'unsigned int' type to 'void *'
type, allowing a wider range of values/types to be stored in this field.
Added 'ide_get_drivedata' and 'ide_set_drivedata' helpers to get and set
the 'drive_data' field.
Fixed all host drivers to maintain coherency with the change in the
'drive_data' field type.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
[bart: fix qd65xx build, cast to 'unsigned long', minor Coding Style fixups]
Acked-by: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Implement test_irq() method based on the driver's former dma_test_irq() methods.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Implement test_irq() method based on the driver's former dma_test_irq() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_test_irq() methods into test_irq() methods. The
driver will now use the standard dma_test_irq() method implementation which
allows to remove 'cmd54x_dma_ops' and 'cmd648_dma_ops' that become identical
to 'sff_dma_ops'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move the ack_intr() method into 'struct ide_port_ops', also renaming it to
test_irq() while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are now two methods that clear the port interrupt: ack_intr() method,
implemented only on M680x0 machines, that is called at the start of ide_intr(),
and clear_irq() method, that is called somewhat later in this function. In
order to stop this duplication, delegate the task of clearing the interrupt
to clear_irq() method, only leaving to ack_intr() the task of testing for the
port interrupt.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove interrupt bit test (not trusted anyway) from siimage_io_dma_test_irq()
and siimage_mmio_dma_test_irq() -- this allows to replace the former function
with now identical ide_dma_test_irq()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_end() methods into clear_irq() methods -- the
driver will now use the standard dma_end() method implementation, ide_dma_end().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now the clear_irq() method is called only from ide_intr() but ide_timer_expiry()
also should call this method in case when drive_is_ready() succeeds...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several errors and warnings given by checkpatch.pl:
- space between the asterisk and parameter name;
- inconsistent spacing between operator and operands;
- space between *sizeof* and open parenthesis;
- #include <asm/io.h> instead of #include <linux/io.h>
- use of *typedef* instead of a structure tag;
- line over 80 characters.
In addition to these changes, also do the following:
- indent with tabs instead of spaces;
- put the function's result type and name/parameters on the same line;
- join back the needlessly broken lines;
- get rid of needless type cast in sgiioc4_checkirq();
- remove space between the type cast and the variable name;
- remove commented out field initializer;
- uppercase the acronyms, lowercase the normal words in the comments;
- fix up the multi-line comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'unsigned long port_flags' field to ide_hwif_t.
* Add IDE_PFLAG_PROBING port flag and keep it set during probing.
* Fix ide_pio_need_iordy() to not enable IORDY at a probe time
(IORDY may lead to controller lock up on certain controllers
if the port is not occupied).
Loosely based on the recent libata's fix by Tejun, thanks to Alan
for the hint that IDE may also need it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_pio_need_iordy() helper and convert host drivers to use it.
This fixes it8172, it8213, pdc202xx_old, piix, slc90e66 and siimage
host drivers to handle IORDY correctly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits)
ide: re-implement ide_pci_init_one() on top of ide_pci_init_two()
ide: unexport ide_find_dma_mode()
ide: fix PowerMac bootup oops
ide: skip probe if there are no devices on the port (v2)
sl82c105: add printk() logging facility
ide-tape: fix proc warning
ide: add IDE_DFLAG_NIEN_QUIRK device flag
ide: respect quirk_drives[] list on all controllers
hpt366: enable all quirks for devices on quirk_drives[] list
hpt366: sync quirk_drives[] list with pdc202xx_{new,old}.c
ide: remove superfluous SELECT_MASK() call from do_rw_taskfile()
ide: remove superfluous SELECT_MASK() call from ide_driveid_update()
icside: remove superfluous ->maskproc method
ide-tape: fix IDE_AFLAG_* atomic accesses
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
pdc202xx_old: kill resetproc() method
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
pdc202xx_old: use ide_dma_test_irq()
ide: preserve Host Protected Area by default (v2)
ide-gd: implement block device ->set_capacity method (v2)
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (28 commits)
ide-tape: fix debug call
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
ide-dma: don't reset request fields on dma_timeout_retry()
ide: drop rq->data handling from ide_map_sg()
ide-atapi: kill unused fields and callbacks
ide-tape: simplify read/write functions
ide-tape: use byte size instead of sectors on rw issue functions
ide-tape: unify r/w init paths
ide-tape: kill idetape_bh
ide-tape: use standard data transfer mechanism
ide-tape: use single continuous buffer
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
ide-tape,floppy: fix failed command completion after request sense
ide-pm: don't abuse rq->data
ide-cd,atapi: use bio for internal commands
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
ide-cd: convert to using generic sense request
ide: add helpers for preparing sense requests
ide-cd: don't abuse rq->buffer
ide-atapi: don't abuse rq->buffer
...
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PowerMac bootup with CONFIG_IDE=y oopses in ide_pio_cycle_time():
because "ide: try to use PIO Mode 0 during probe if possible" causes
pmac_ide_set_pio_mode() to be called before drive->id has been set.
Bart points out other places which now need drive->id set earlier,
so follow his advice to allocate it in ide_port_alloc_devices()
(using kzalloc_node, without error message, as when allocating drive)
and memset it for reuse in ide_port_init_devices_data().
Fixed in passing: ide_host_alloc() was missing ide_port_free_devices()
from an error path.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_probe_port() skip probe if ide_port_wait_ready() returns -ENODEV
and print error message instead of debug one if it returns -EBUSY.
v2:
Fix the default 'rc' value.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_NIEN_QUIRK device flag and use it instead of
drive->quirk_list.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_nien_quirk_list() helper to the core code
and then use it in ide_port_tune_devices().
* Remove no longer needed ->quirkproc methods from hpt366.c
and pdc202xx_{new,old}.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enable also quirks in do_reset1() and ide_config_drive_speed()
for devices on quirk_drives[] list.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With ->write_devctl method call (which unmasks drive IRQ) preceding
SELECT_MASK() call there is really no need for the latter.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We always call SELECT_MASK(drive, 0) after ide_dev_read_id() call
so there is no need to do it again in the error path.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[inspired by pata_icside]
Enabling/disabling of card IRQs is handled fine by IRQ and IDE
subsystems so there is no need for custom ->maskproc method.
Moreover icside_maskproc() would enable IRQ only if it was already
enabled [because of 'if (state->enabled && !mask)' check].
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These flags used to be bit numbers and now are single bits in the
->atapi_flags vector. Use them properly.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are two sites where the flag is being changed: ide_retry_pc
and idetape_do_request. Both codepaths are protected by hwif->busy
(ide_lock_port) and therefore we shouldn't need the atomic accesses.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's resetproc() method resets both channels at once -- most probably
by driving RESET- on them. Not only such reset can severely disturb concurrent
operations on another channel, it also ensues 2-second delay, while there's no
apparent reason why SRST reset being performed prior to resetproc() call needs
to be followed up by another reset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_lost_irq() and dma_clear() methods call pdc202xx_reset()
which resets both channels at once -- most probably by driving RESET- on them.
Not only such reset can severely disturb concurrent operations on another
channel, it is also a clear overkill (especially in the first case) and is
completely unexpected and thus not properly handled by the IDE core in this
context (in the second case the usual SRST reset would most probably ensue
anyway though); it also causes quite arbitrary 2-second delay. Hence, use the
standard ide_dma_lost_irq() method and don't install the optional dma_clear()
method at all -- the driver should do well without this age-old cruft...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_test_irq() method, although tests some chip specific interrupt
bits, finally always relies on the SFF-8038i standard interrupt bit. I see no
point in testing the bits that are not trusted anyway -- the driver should be
fully able to use the standard method implemetation, ide_dma_test_irq().
With this change 'pdc202xx_dma_ops' finally becomes identical to 'sff_dma_ops',
and we can get rid of it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit ac95beedf8 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit 942dcd85bf
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit 4b58f17d7c
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The recent move to accessor functions for querying queue limits
missed an entry in ide-disk.c:
drivers/ide/ide-disk.c: In function ‘ide_disk_setup’:
drivers/ide/ide-disk.c:642: error: ‘struct request_queue’ has no member named ‘max_sectors’
Fix it.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_regs_t typedef and rename struct hw_regs_s to struct ide_hw.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Pass number of ports to ide_host_{alloc,add}() and then update
all users accordingly.
v2:
- drop no longer needed NULL initializers in buddha.c, cmd640.c and gayle.c
(noticed by Sergei)
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert host drivers that still use hw_regs_t's chipset field to use
the one in struct ide_port_info instead.
* Move special handling of ide_pci chipset type from ide_hw_configure()
to ide_init_port().
* Remove chipset field from hw_regs_t.
While at it:
- remove stale comment in delkin_cb.c
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace:
- special_t typedef by IDE_SFLAG_* flags
- 'special_t special' ide_drive_t's field by 'u8 special_flags' one
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- change debug printk() level to KERN_DEBUG and use __func__
- update documentation
v2:
- fix DEBUG build (noticed by Sergei)
There should be no functional changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Initially set PIO Mode 0 for all host drivers that have a 'set_pio_mode'
method before the IDE core figures out the most suited PIO mode for the
attached device.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This error only occurs when IDETAPE_DEBUG_LOG is enabled.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c10726 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_check_ireason() function that handles all ATAPI devices.
Reorganize all unlikely cases in ireason checking further down in the
code path.
In addition, add PFX for printks originating from ide-atapi. Finally,
remove ide_cd_check_ireason.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now that we use a static request_sense buffer, use it instead of the
first 18 bytes only. Also, remove sense-arg to cdrom_analyze_sense_data
and cdrom_log_sense since we can access it through drive->sense_data
now.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now after all users of pc->buf have been converted, remove the 64B buffer
embedded in each packet command.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
ide-tape used to issue READ POSITION in several places and the
evaluation of the returned READ POSITION data was done in the
->pc_callback. Convert it to use local buffer and move that
evaluation chunk in the idetape_read_position(). Additionally, fold
idetape_create_read_position_cmd() into it, too, thus concentrating READ
POSITION handling in one method only and making all places call that.
Finally, mv {idetape,ide_tape}_read_position.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Access the sense buffer through the bio in ->pc_callback method thus
alleviating the need for the pc->buf pointer.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Pass the buffer into ide_floppy_create_format_unit_cmd instead of using
pc->buf.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This is in preparation of removing ide_atapi_pc. Expose the buffer as an
argument to ide_queue_pc_tail with later replacing it with local buffer
or even kmalloc'ed one if needed due to stack usage constraints.
Also, add the possibility of passing a NULL-ptr buffer for cmds which
don't transfer data besides the cdb. While at it, switch to local buffer
in idetape_get_mode_sense_results().
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This is in preparation for removing ide_atapi_pc.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now that we have rq->resid_len, use it to account partial completion
amount during the lifetime of an rq, decrementing it on each successful
transfer. As a result, get rid of now unused pc->xferred.
While at it, remove noisy debug call in ide_prep_sense.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
After the recent struct request cleanups, blk_rq_bytes() is guaranteed
to be valid and is the current total length of the rq's bio. Use that
instead of pc->req_xfer in the do_request() path after the command has
been queued
The remaining usage of pc->req_xfer now is only until we map the rq to a
bio.
While at it:
- remove local caching of rq completion length in ide_tape_issue_pc()
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
ide-tape had a potential bug for fs requests when preparing the command
packet: it was writing the transfer length as a number of fixed blocks.
However, the block layer implies 512 byte blocks and ide-tape can have
other block sizes so account for that too.
ide-floppy does this calculation properly with the block size factor
(floppy->bs_factor).
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide generally has single request in flight and tracks it using
hwif->rq and all state handlers follow the following convention.
* ide_started is returned if the request is in flight.
* ide_stopped is returned if the queue needs to be restarted. The
request might or might not have been processed fully or partially.
* hwif->rq is set to NULL, when an issued request completes.
So, dequeueing model can be implemented by dequeueing after fetch,
requeueing if hwif->rq isn't NULL on ide_stopped return and doing
about the same thing on completion / port unlock paths. These changes
can be made in ide-io proper.
In addition to the above main changes, the following updates are
necessary.
* ide-cd shouldn't dequeue a request when issuing REQUEST SENSE for it
as the request is already dequeued.
* ide-atapi uses request queue as stack when issuing REQUEST SENSE to
put the REQUEST SENSE in front of the failed request. This now
needs to be done using requeueing.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all direct users
to accessors.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide doesn't manipulate request fields anymore and thus all hard and
their soft equivalents are always equal. Convert all references to
accessors.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->sector is set to the tape->first_frame but it's never actually
used and not even in the correct unit (512 byte sectors). Don't set
it.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some time ago we had to disable init_hwif callback for PowerPC builds.
That was because of a historical IRQ overwrite in the driver, which
was causing IDE malfunction on the MPC8610HPCD PowerPC boards.
It's unclear whether this overwrite is still useful, but it is proven
to cause a bit of harm, and today some PowerPC targets (Xilinx ML510,
as reported by Roderick Colenbrander) need the init_hwif, so we have
to re-enable it and remove the overwrite.
Reported-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Original patch (dfa4411cc3) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugfixes noted by checking the code against the controller
documentation (TI document number SPRUE21):
- Remove declarations for eight non-existent registers (!);
and remove accesses to two of them.
- Remove access to various non-existent bitfields in some of
the registers which *do* exist (those fields must-be-zero).
- Provide comment to replace bogus reset logic (removed above,
it relied on non-existent bitfields). Resets require GPIO
help; this driver doesn't currently know about that.
With some minor cleanup: relocate a comment, avoid an extra
lookup of the PIO timings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
My laptop (Acer Travelmate 660) always cuts the power when rebooting
which causes the disk to emergency-park it's head.
Add a dmi check to stop disk as for shutdown on this laptop.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With 2.6.30-rc2 I face a kernel crash on the 32bit hppa architecture
due to ide-cd when udev creates the device nodes at startup:
Kernel Fault: Code=26 regs=8ed34c40 (Addr=00000024)
IASQ: 00000000 00000000 IAOQ: 1034b5ac 1034b5b0
IIR: 4ab30048 ISR: 00000000 IOR: 00000024
CPU: 0 CR30: 8ed34000 CR31: ffff55ff
ORIG_R28: 00000000
IAOQ[0]: ide_complete_rq+0x2c/0x70
IAOQ[1]: ide_complete_rq+0x30/0x70
RP(r2): cdrom_newpc_intr+0x178/0x46c
Backtrace:
[<1035c608>] cdrom_newpc_intr+0x178/0x46c
[<1034c494>] ide_intr+0x1b0/0x214
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<102f7864>] superio_interrupt+0x88/0xbc
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<10112efc>] do_cpu_irq_mask+0x9c/0xd0
[<10116068>] intr_return+0x0/0x4
This crash seems to happen due to an uninitialized variable "rc".
The compiler even warns about that:
CC drivers/ide/ide-cd.o
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c: In function `cdrom_newpc_intr':
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c:612: warning: `rc' might be used uninitialized in this function
After applying the trivial patch below, which just initializes
the variable to zero, the kernel doesn't crash any longer:
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x54 <3>{ AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
done.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Linus <torvalds@linux-foundation.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix UDMA throughput bug: tCYC averages t2CYCTYP/2, but the code
previously assumed it was the same as t2CYCTYP. (That is, it was
using just one clock edge, not both.) Move the table's type
declaration so it's adjacent to the table, making it more clear
what those numbers mean.
On one system this change increased throughput by almost 4x: UDMA/66
sometimes topped 23 MB/sec (on a drive known to do much better). On
another system it was around a 10% win (UDMA/66 up to 7+ MB/sec).
The difference might be caused by the ratio between memory and IDE
clocks. In the system with large speedup, this was exactly 2 (as a
workaround for a rev 1.1 silicon bug). The other system used a more
standard ratio of 1.63 (and rev 2.1 silicon) ... clock domain synch
might have some issues, they're not unheard-of.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As we have already PIO 6 transfer mode supported in IDE layer, we can turn
it on in the driver.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: "Steve Wootton" <swootton@esi-estech.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the case of flushing the drive's cache explicit.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use write_devctl() method to clear/set the HOB bit in tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move device register masking (and setting drive->select) out of tf_load() method
and into the only function that needs to use this code, do_rw_taskfile()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix whitespace error]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make 'struct ide_taskfile' cover only 8 register values and thus put two such
fields ('tf' and 'hob') into 'struct ide_cmd', dropping unnecessary 'tf_array'
field from it.
This required changing the prototype of ide_get_lba_addr() and ide_tf_dump().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix setting of ATA_LBA bit for LBA48 commands in __ide_do_rw_disk()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace IDE_TFLAG_{IN|OUT}_* flags meaning to the taskfile register validity on
input/output by the IDE_VALID_* flags and introduce 4 symmetric 8-bit register
validity indicator subfields, 'valid.{input/output}.{tf|hob}', into the 'struct
ide_cmd' instead of using the 'tf_flags' field for that purpose (this field can
then be turned from 32-bit into 8-bit one).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Fix intendation in cdrom_decode_status(), no real code changes.
While at it:
- beautify comments
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Unify handling of fs and pc requests in cdrom_decode_status().
While at it:
- remove unreachable code
The only change in functionality is that for pc requests more
detailed error message will be printed for following sense keys:
* ILLEGAL_REQUEST
* DATA_PROTECT
* MEDIUM_ERROR
* BLANK_CHECK
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Convert cdrom_decode_status() to use switch statements in
preparation to unify handling of fs and pc requests.
While at it:
- remove superfluous comments and do minor CodingStyle fixups
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now tx493[89]ide_tf_{load,read} do not contain word I/O operations.
They are endian-free now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using I/O port accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using MMIO accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove two no longer used functions that I've overlooked...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* define CHECK_DMA_MASK
* remove use of wmb()
Reported-by: Grant Grundler <grundler@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
This patch:
o replaces "mask" variable in ide_dma_end() with #define.
o removes use of wmb() in ide-dma-sff.c and scc_pata.c.
o is not tested - I don't have (or want) the HW.
Signed-off-by: Grant Grundler <grundler@google.com>
Cc: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Both of commits f94116aeec ("ide: cleanup
<asm-m68k/ide.h>") and 15a453a955 ("ide: include
<asm/ide.h> only when needed") break falconide:
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| ide0 at 0xfff00000 on irq 15 (serialized)
| ide-gd driver 1.18
| hda: max request size: 128KiB
| hda: 2118816 sectors (1084 MB) w/256KiB Cache, CHS=2102/16/63
| hda:<4>hda: lost interrupt
This happens because falconide relies on {in,out}sw() being redefined in
<asm/ide.h>, as included by <linux/ide.h>, which is no longer the case.
Use __ide_mm_{in,out}sw() from <asm/ide.h> instead, just like
ide_{in,out}put_data() do.
The same problem seems to exist in q40ide.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 255115fb35 ("ide: allow host drivers to
specify IRQ flags") added irq_flags fields to struct ide_port_info and struct
ide_host. Drivers can now set ide_port_info.irq_flags = IRQF_SHARED, while
init_irq() passes ide_host.irq_flags to request_irq().
Unfortunately ide_host.irq_flags is never set, causing (on ARAnyM):
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| init_irq: sa = 0
| ide0: disabled, unable to get IRQ 15
| ide0: failed to initialize IDE interface
| ide0: disabling port
Solve this by copying ide_port_info.irq_flags to ide_host.irq_flags in
ide_host_alloc().
This bug probably affects the following IDE host drivers:
- buddha
- delkin_cb
- falconide
- gayle
- ide-cs
- macide
- q40ide
- scc_pata
- sgiioc4
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... and access them afterwards. Simplify rq completing code while at it.
Spotted-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No reason to need IDE built-in to be able to compile pmac driver.
Tested to work on 2.6.29-rc8 and 2.6.28.8 with ide and pmac as modules
inside an initramfs.
Signed-off-by: Gilles Espinasse <g.esp@free.fr>
Cc: sam@ravnborg.org
Cc: benh@kernel.crashing.org
[bart: remove now superfluous IDE check]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As IDE cable used on Apple PowerBook/iBook laptops are always of "Short 40"
type when the firmware says it's 80 conductor one, the cable detection should
return ATA_CBL_PATA40_SHORT on those machines. This enables to automatically
use UDMA5 even with drives that doesn't correctly detect those cables on Apple
laptops.
Signed-off-by: TOMARI Hisanobu <posco.grubb@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
[bart: beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since SELECT_DRIVE() has boiled down to a mere dev_select() method call, it now
makes sense to just inline it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn selectproc() method into dev_select() method by teaching it to write to the
device register and moving it from 'struct ide_port_ops' to 'struct ide_tp_ops'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
Cc: petkovbb@gmail.com
[bart: add ->dev_select to at91_ide.c and tx4939.c (__BIG_ENDIAN case)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IDE_FTFLAG_{IN|OUT}_DATA flag handling out of tf_{read|load}() methods
into the only two functions where these flags actually need to be handled:
do_rw_taskfile() and ide_complete_cmd()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Handle IDE_FTFLAG_{IN|OUT}_DATA flags in tf_{read|load}() methods by calling
{in|out}put_data() methods to transfer 2 bytes -- this will allow us to move
that handling out of those methods altogether...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_{in|out|put_data() can be somewhat shortened by merging the paths doing
16-bit I/O...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The feature register has never been readable -- when its location is read, one
gets the error register value; hence rename IDE_TFLAG_IN_[HOB_]FEATURE into
IDE_TFLAG_IN_[HOB_]ERROR and introduce the 'hob_error' field into the 'struct
ide_taskfile' (despite the error register not really depending on the HOB bit).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn set_irq() method with its software reset hack into write_devctl() method
(for just writing a value into the device control register) at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_HOB instead of hard-coded value in the tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_ERR instead of hard-coded value in idedisk_set_max_address()
and idedisk_read_native_max_address().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.
Since there were no PIO5 capable hard drives produced and one would also need
66 MHz IDE clock to actually get the difference WRT the address setup timings
programmed, I decided to simply replace the old non-standard PIO mode 5 timings
with the CFA specified ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stf_xl@wp.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bytes indicating current DMA mode in the identify data words 62, 63, and 88
should only change on setting a DMA mode, so stop clearing them on setting PIO
mode in ide_config_drive_speed(). While at it, correct SW/MW DMA mode masks...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE code assumed for years that the bit 1 of the identify data word 53 also
covers the validity of the SW/MW DMA information in words 62 and 63, but it has
always covered only words 64 thru 70, with words 62 and 63 being defined in the
original ATA spec, not in ATA-2...
This fix however should only concern *very* old hard disks and rather old CF
cards...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make auide_{insw|outsw}() 'static' and mark them 'inline' as there's only one
call site for each: in the driver's {in|out}put_data() methods respectively...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix ide_init_sg_cmd() setup for non-fs requests.
* Convert ide_pc_intr() to use ide_pio_bytes() for floppy media.
* Remove no longer needed ide_io_buffers() and sg/sg_cnt fields
from struct ide_atapi_pc.
* Remove partial completions; kill idefloppy_update_buffers(), as a
result.
* Add some more debugging statements.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return number of bytes left to transfer from idetape_{in,out}put_buffers()
and number of bytes done from ide_tape_io_buffers().
* Fix padding for PIO transfers in ide_pc_intr() so read/write buffers are
always completely processed and then the transfer is padded if necessary.
* Remove invalid error messages.
* Remove now superfluous padding from ide{_io_buffers,tape_input_buffers}().
While at it:
* Set pc->bh to NULL in idetape_input_buffers() after all bh-s are done.
* Cache !!(pc->flags & PC_FLAG_WRITING) in local variable in ide_pc_intr().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays it is not worth having a separate config option for
Amiga IDE Doubler support so always include it (it still needs
to be explicitly enabled by module parameter).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
struct ide_atapi_pc is often allocated on the stack and size of ->pc_buf
size is 256 bytes. However since only ide_floppy_create_read_capacity_cmd()
and idetape_create_inquiry_cmd() require such size allocate buffers for
these pc-s explicitely and decrease ->pc_buf size to 64 bytes.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need for a separate ide_arm host driver nowadays
so merge it into ide_generic one.
While at it:
- return -EBUSY from ide_generic_init() if I/O resources are busy
- scale down ide_generic_check_pci_legacy_iobases() for CONFIG_PCI=n
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we have "ide_generic.probe_mask=" module parameter
and ide_platform host driver so sysfs interface for adding
IDE interfaces is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_map_sg() calls out from ide_build_sglist()
to ide_dma_prepare().
* Pass command to ide_destroy_dmatable().
* Rename ide_build_sglist() to ide_dma_map_sg()
and ide_destroy_dmatable() to ide_dma_unmap_sg().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set/clear drive->waiting_for_dma flag in the core code
instead of in ->dma_setup and ->dma_end methods.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_map_sg() call from ->dma_setup implementations and
ide_destroy_dmatable() one from *_build_dmatable() to ide_dma_prepare().
There should be no functional changes caused by this patch.
Sergei:
Removed 'use_pio_instead' labels and replaced 'goto' with 'return 0' --
that required no changes to the follow-up patches...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add (an optional) ->dma_check method for checking if DMA can be
used for a given command and fail DMA setup in ide_dma_prepare()
if necessary.
* Convert alim15x3 and trm290 host drivers to use ->dma_check.
* Rename ali15x3_dma_setup() to ali_dma_check() while at it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle trm290_prepare_drive()
there instead of in ->dma_setup method.
There should be no functional changes caused by this patch
(DMA support is disabled currently in trm290.c).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle ns87415_prepare_drive()
there instead of in ->dma_setup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_dma_prepare() helper.
* Convert ide_issue_pc() and do_rw_taskfile() to use it.
* Make ide_build_sglist() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_timeout() is only used by ide_dma_timeout_retry()
inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All custom ->dma_timeout implementations call the generic one thus it is
possible to have only an optional method for resetting DMA engine instead:
* Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105
host drivers to use it.
* Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove
->dma_timeout method.
* Make ide_dma_timeout() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cache drive->queue in local variable and use max().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'thislen' is always <= cmd->nleft for non-fs requests so the transfer
padding inside the 'while (thislen > 0)' loop can happen only for fs
requests -- then move it out of the loop and unify with the transfer
padding for non-fs requests ('thislen' == 'len' for fs requests).
* blk_dump_rq_flags() dumps all request flags so it is enough to pass
only the function name to it.
* Update my Copyrights while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use the following facts:
- rq->nr_sectors should now be always equal to (non-zero)
rq->hard_nr_sectors for fs requests
- REQ_TYPE_ATA_PC requests have never bio attached to them
- rq->hard_nr_sectors == 0 for REQ_TYPE_ATA_PC requests
- DMA is used only for fs, pc and REQ_TYPE_ATA_PC requests
- 'uptodate' is ignored for pc requests ('rc == 0' case)
and use the common completion path also for DMA requests.
There should be no functional changes caused by this patch
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide-cd to use scatterlists for PIO transfers and get rid of
partial completions (except on error) also for non-fs requests.
v2:
Do not map dataless commands to an sg since it oopses on the virt_to_page()
translation check when DEBUG_VIRTUAL is enabled. (from Borislav Petkov,
reported/bisected-by Tetsuo Handa).
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We now support arbitrary number of bytes per-IRQ also for fs requests
so remove ide_cd_check_transfer_size() and IDE_AFLAG_LIMIT_NFRAMES.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Export ide_pio_bytes().
* Add ->last_xfer_len field to struct ide_cmd.
* Add ide_cd_error_cmd() helper to ide-cd.
* Convert ide-cd to use scatterlists also for PIO transfers (fs requests
only for now) and get rid of partial completions (except when the error
happens -- which is still subject to change later because looking at
ATAPI spec it seems that the device is free to error the whole transfer
with setting the Error bit only on the last transfer chunk).
* Update ide_cd_{prepare_rw,restore_request,do_request}() accordingly.
* Inline ide_cd_restore_request() into cdrom_start_rw().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Inline cdrom_end_request() into cdrom_newpc_intr()
and ide_cd_do_request().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_decode_status()
and ide_cd_check_ireason() to cdrom_newpc_intr().
* Unify cdrom_newpc_intr() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move setting REQ_FAILED flag out from 'end_request' exit path in
cdrom_newpc_intr() and also rename 'end_request' to 'out_end'.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_start_rw()
and ide_cd_prepare_rw_request() to ide_cd_do_request().
* Unify ide_cd_do_request() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It makes no sense to check for BSY bit being set as earlier OK_STAT()
check in cdrom_end_request() makes sure that BSY bit is cleared.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_end_rq() also for failed non-fs requests on completion
of REQUEST SENSE requests + use blk_rq_bytes() while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use PageHighMem() instead of ifdefs in ide_pio_bytes()
(=> local IRQs won't be disabled when not necessary).
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for arbitrary transfer lengths to ide_pio_bytes()
and then inline ide_pio_multi() into ide_pio_datablock().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently¹, some ATAPI devices want to see the packet command first
before enabling DMA otherwise they simply hang indefinitely. Reorder the
two steps and start DMA only after having issued the command first.
[1] http://marc.info/?l=linux-kernel&m=123835520317235&w=2
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Reported-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix some incorrect IDE_FTFLAG_* changes which slipped in commit
"ide: add "flagged" taskfile flags to struct ide_taskfile (v2)"
(commit 19710d25d5) few days ago.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On m68k:
| drivers/ide/ide-atapi.c: In function 'ide_io_buffers':
| drivers/ide/ide-atapi.c:87: error: implicit declaration of function 'sg_page'
| drivers/ide/ide-atapi.c:87: warning: passing argument 1 of 'PageHighMem' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:91: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:96: error: implicit declaration of function 'sg_virt'
| drivers/ide/ide-atapi.c:96: warning: assignment makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:107: error: implicit declaration of function 'sg_next'
| drivers/ide/ide-atapi.c:107: warning: assignment makes pointer from integer without a cast
[bart: Dmitri Vorobiev submitted similar patch fixing MIPS]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Unfortunately, I missed a catch when reviewing the patch committed as
201bffa4. Here is the fix to the currently broken handling of sleeping
devices. In particular, this is required to get the disk shock
protection code working again.
Reported-by: Christian Thaeter <ct@pipapo.org>
Cc: stable@kernel.org
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass number of bytes instead of sectors to ide_init_sg_cmd().
* Pass number of bytes to process to ide_pio_sector() and rename
it to ide_pio_bytes().
* Rename ->nsect field to ->nbytes in struct ide_cmd and use
->nbytes, ->nleft and ->cursg_ofs to keep track of number of
bytes instead of sectors.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass command structure to ide_execute_command() and skip
__ide_set_handler() for ATAPI protocols on non-DRQ devices.
* Convert ide_issue_pc() to always use ide_execute_command()
and remove no longer needed ide_execute_pkt_cmd().
v2:
* Fix for non-DRQ devices (based on report from Borislav).
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename dma_timer_expiry() to ide_dma_sff_timer_expiry() and export it.
* Add ->dma_timer_expiry method and use it to set hwif->expiry for
ATA_PROT_DMA protocol in do_rw_taskfile().
* Initialize ->dma_timer_expiry to ide_dma_sff_timer_expiry() for SFF hosts.
* Move setting hwif->expiry from ide_execute_command() to its users and drop
'expiry' argument.
* Use ide_execute_command() instead of ->dma_exec_cmd in do_rw_taskfile().
* Remove ->dma_exec_cmd method and its implementations.
* Unexport ide_execute_command() and ide_dma_intr().
v2:
* Fix CONFIG_BLK_DEV_IDEDMA=n build (noticed by Randy Dunlap).
* Fix *dma_expiry naming (suggested by Sergei Shtylyov).
There should be no functional changes caused by this patch.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set hwif->expiry prior to calling [__]ide_set_handler()
and drop 'expiry' argument.
* Set hwif->expiry to NULL in ide_{timer_expiry,intr}()
and remove 'hwif->expiry = NULL' assignments.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Grant Likely