Add error check after all calls to acpi_ns_get_pathname_length.
Add status return from acpi_ns_build_external_path and check after
all calls. Add parameter validation to acpi_ut_initialize_buffer.
Reported by and initial patch by Ingo Molnar.
http://lkml.org/lkml/2008/7/21/176
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The DdbHandle returned by Load() does not have its reference count
decremented during unload, leading to a memory leak. Lin Ming.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fixes a possible memory leak when thermal and processor objects
are deleted. Any associated notify handlers (and objects) were
not being deleted. Fiodor Suietov. BZ 506
http://www.acpica.org/bugzilla/show_bug.cgi?id=506
Signed-off-by: Fiodor Suietov <fiodor.f.suietov@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
usb: musb: pass configuration specifics via pdata
usb: musb: fix hanging when rmmod gadget driver
USB: Add MUSB and TUSB support
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
USB: Add vendor/product id of ZTE MF628 to option
USB: quirk PLL power down mode
USB: omap_udc: fix compilation with debug enabled
usb: cdc-acm: drain writes on close
usb: cdc-acm: stop dropping tx buffers
usb: cdc-acm: bugfix release()
usb gadget: issue notifications from ACM function
usb gadget: remove needless struct members
USB: sh: r8a66597-hcd: fix disconnect regression
USB: isp1301: fix compilation
USB: fix compiler warning fix
usb-storage: unusual_devs entry for Nokia 5300
USB: cdc-acm.c: Fix compile warnings
USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
usb: isp1760: don't be noisy about short packets.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
netns: Fix crash by making igmp per namespace
bnx2x: Version update
bnx2x: Checkpatch compliance
bnx2x: Spelling mistakes
bnx2x: Minor code improvements
bnx2x: Driver info
bnx2x: 1G LED does not turn off
bnx2x: 8073 PHY changes
bnx2x: Change GPIO for any port
bnx2x: Pause settings
bnx2x: Link order with external PHY
bnx2x: No LRO without Rx checksum
bnx2x: Wrong structure size
bnx2x: WoL capability
bnx2x: Clearing MAC addresses filters
bnx2x: Delay in while loops
bnx2x: PBA Table Page Alignment Workaround
bnx2x: Self-test false positive
bnx2x: Memory allocation
bnx2x: HW attention lock
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Engraf <david.engraf@netcom.eu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes to the usb_driver_release_interface() usage;
(a) make sure releasing *either* interface first will release
the other, instead of insisting it be the control interface;
(b) remove the recently-added self-deadlock.
(The "fix disconnect bug in cdc-acm" patch was incomplete and incorrect.)
Plus a small "sparse" fix: rename a local variable so it doesn't
shadow a function parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes some unused members from the various USB functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the regression in commit 29fab0cd89
that this driver executed reconnection processing when disconnected
some devices.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1123b) fixes a compiler warning: do_unbind_rebind() is
defined but not used if CONFIG_PM=n.
Problem originally found and initial patch submitted by Alexander
Beregalov <a.beregalov@gmail.com>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Cedric Godin <cedric@belbone.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The irq flags should be unsigned long.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.
It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update RX path handling in new serial gadget code to cope better with
RX blockage: queue every RX packet until its contents can safely be
passed up to the ldisc. Most of the RX path work is now done in the
RX tasklet, instead of just the final "push to ldisc" step. This
addresses some cases of data loss:
- A longstanding serial gadget bug: when tty_insert_flip_string()
didn't copy the entire buffer, the rest of the characters were
dropped! Now that packet stays queued until the rest of its data
is pushed to the ldisc.
- Another longstanding issue: in the unlikely case that an RX
transfer returns data and also reports a fault, that data is
no longer discarded.
- In the recently added RX throttling logic: it needs to stop
pushing data into the TTY layer, instead of just not submitting
new USB read requests. When the TTY is throttled long enough,
backpressure will eventually make the OUT endpoint NAK.
Also: an #ifdef is removed (no longer necessary); and start switching
to a better convention for debug messages (prefix them with tty name).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add razr v3xx US_FL_FIX_CAPACITY flag to unusual_devs.h in usb-storage
This is another Motorola phone that incorrectly reports the sector count
(off by one).
Problem Description: io errors when mounting phone's sd-card via the
phones usb port
Steps to reproduce: mount Motorola Razr v3xx phones sd-card on Linux Desktop
via usb cable. Phones USB port must be in memory card mode.
DEBUG output:
Jul 9 19:32:41 micky kernel: Buffer I/O error on device sdd, logical block 3970048
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Sense Key : Medium Error [current]
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Add. Sense: No additional sense information
Jul 9 19:32:41 micky kernel: end_request: I/O error, dev sdd, sector 3970048
From: Jost Diederichs <jost@qdusa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moves responsbility of TRU-Install (i.e. ZeroCD) to the usb-storage
driver. See patch 04/04 of this set.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Very minor changes to clean up sierra code. Adds a prefix to debug messages so
that Sierra messages are easily recognized. Removes extraneous code.
This targets kernel 2.6.26-rc9
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB ID 4348:5523 is handled by the ch341 driver. Remove it from the
pl2023 driver.
Reverts 002e8f2c80.
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes "USB Monitor" appear under "Miscellaneous USB options"
section instead of in the middle of device specific drivers in the
"USB Imaging devices" section.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it, we might have trouble when trying to write
some composite gadget drivers.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1114) fixes a problem that was revealed by an earlier
patch (as1069b). Some broken controllers seem never to turn off their
RHCS interrupt status bit, even when told to do so. As a result they
generate an interrupt storm and hang the system.
The patch avoids enabling RHSC interrupt requests when the RHCS status
bit is already set. This should have no adverse affects on normal
controllers, since they won't set the status bit until a root-hub
status change actually occurs, in which case we wouldn't enable RHSC
interrupt requests anyway -- we would wait until the status change had
been processed and cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb/core/driver: fix warning:
drivers/usb/core/driver.c:834: warning: 'do_unbind_rebind' defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.
Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: Andre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a BUG() turned up by Ingo via randconfig testing, where
CONFIG_LIST_DEBUG turned up list corruption. The corruption was
caused by the dummy_hcd (single-machine test harness for gadget and
HCD code) trashing the request queue when driven by the new CDC
composite gadget an I/O pattern that was previously uncommon.
Fix suggested by Alan Stern.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Checkpatch compliance
The latest version of checkpatch found the following style errors in the
code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes
Spelling has to L's in it...
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1G LED does not turn off
The 1G LED was not switched to off when the link was lost
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Walter reported this oops on his via C3 using padlock for
AES-encryption:
##################################################################
BUG: unable to handle kernel NULL pointer dereference at 000001f0
IP: [<c01028c5>] __switch_to+0x30/0x117
*pde = 00000000
Oops: 0002 [#1] PREEMPT
Modules linked in:
Pid: 2071, comm: sleep Not tainted (2.6.26 #11)
EIP: 0060:[<c01028c5>] EFLAGS: 00010002 CPU: 0
EIP is at __switch_to+0x30/0x117
EAX: 00000000 EBX: c0493300 ECX: dc48dd00 EDX: c0493300
ESI: dc48dd00 EDI: c0493530 EBP: c04cff8c ESP: c04cff7c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process sleep (pid: 2071, ti=c04ce000 task=dc48dd00 task.ti=d2fe6000)
Stack: dc48df30 c0493300 00000000 00000000 d2fe7f44 c03b5b43 c04cffc8 00000046
c0131856 0000005a dc472d3c c0493300 c0493470 d983ae00 00002696 00000000
c0239f54 00000000 c04c4000 c04cffd8 c01025fe c04f3740 00049800 c04cffe0
Call Trace:
[<c03b5b43>] ? schedule+0x285/0x2ff
[<c0131856>] ? pm_qos_requirement+0x3c/0x53
[<c0239f54>] ? acpi_processor_idle+0x0/0x434
[<c01025fe>] ? cpu_idle+0x73/0x7f
[<c03a4dcd>] ? rest_init+0x61/0x63
=======================
Wolfgang also found out that adding kernel_fpu_begin() and kernel_fpu_end()
around the padlock instructions fix the oops.
Suresh wrote:
These padlock instructions though don't use/touch SSE registers, but it behaves
similar to other SSE instructions. For example, it might cause DNA faults
when cr0.ts is set. While this is a spurious DNA trap, it might cause
oops with the recent fpu code changes.
This is the code sequence that is probably causing this problem:
a) new app is getting exec'd and it is somewhere in between
start_thread() and flush_old_exec() in the load_xyz_binary()
b) At pont "a", task's fpu state (like TS_USEDFPU, used_math() etc) is
cleared.
c) Now we get an interrupt/softirq which starts using these encrypt/decrypt
routines in the network stack. This generates a math fault (as
cr0.ts is '1') which sets TS_USEDFPU and restores the math that is
in the task's xstate.
d) Return to exec code path, which does start_thread() which does
free_thread_xstate() and sets xstate pointer to NULL while
the TS_USEDFPU is still set.
e) At the next context switch from the new exec'd task to another task,
we have a scenarios where TS_USEDFPU is set but xstate pointer is null.
This can cause an oops during unlazy_fpu() in __switch_to()
Now:
1) This should happen with or with out pre-emption. Viro also encountered
similar problem with out CONFIG_PREEMPT.
2) kernel_fpu_begin() and kernel_fpu_end() will fix this problem, because
kernel_fpu_begin() will manually do a clts() and won't run in to the
situation of setting TS_USEDFPU in step "c" above.
3) This was working before the fpu changes, because its a spurious
math fault which doesn't corrupt any fpu/sse registers and the task's
math state was always in an allocated state.
With out the recent lazy fpu allocation changes, while we don't see oops,
there is a possible race still present in older kernels(for example,
while kernel is using kernel_fpu_begin() in some optimized clear/copy
page and an interrupt/softirq happens which uses these padlock
instructions generating DNA fault).
This is the failing scenario that existed even before the lazy fpu allocation
changes:
0. CPU's TS flag is set
1. kernel using FPU in some optimized copy routine and while doing
kernel_fpu_begin() takes an interrupt just before doing clts()
2. Takes an interrupt and ipsec uses padlock instruction. And we
take a DNA fault as TS flag is still set.
3. We handle the DNA fault and set TS_USEDFPU and clear cr0.ts
4. We complete the padlock routine
5. Go back to step-1, which resumes clts() in kernel_fpu_begin(), finishes
the optimized copy routine and does kernel_fpu_end(). At this point,
we have cr0.ts again set to '1' but the task's TS_USEFPU is stilll
set and not cleared.
6. Now kernel resumes its user operation. And at the next context
switch, kernel sees it has do a FP save as TS_USEDFPU is still set
and then will do a unlazy_fpu() in __switch_to(). unlazy_fpu()
will take a DNA fault, as cr0.ts is '1' and now, because we are
in __switch_to(), math_state_restore() will get confused and will
restore the next task's FP state and will save it in prev tasks's FP state.
Remember, in __switch_to() we are already on the stack of the next task
but take a DNA fault for the prev task.
This causes the fpu leakage.
Fix the padlock instruction usage by calling them inside the
context of new routines irq_ts_save/restore(), which clear/restore cr0.ts
manually in the interrupt context. This will not generate spurious DNA
in the context of the interrupt which will fix the oops encountered and
the possible FPU leakage issue.
Reported-and-bisected-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Later SEC revision requires the link table (used for scatter/gather)
to have an extra entry to account for the total length in descriptor [4],
which contains cipher Input and ICV.
This only applies to decrypt, not encrypt.
Without this change, on 837x, a gather return/length error results
when a decryption uses a link table to gather the fragments.
This is observed by doing a ping with size of 1447 or larger with AES,
or a ping with size 1455 or larger with 3des.
So, add check for SEC compatible "fsl,3.0" for using extra link table entry.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Discard double CQE for one WR
IB/ehca: Check idr_find() return value
IB/ehca: Repoll CQ on invalid opcode
IB/ehca: Rename goto label in ehca_poll_cq_one()
IB/ehca: Update qp_state on cached modify_qp()
IPoIB/cm: Use vmalloc() to allocate rx_rings
Various cleanup the drivers/firmware/memmap (after review by AKPM):
- fix kdoc to conform to the standard
- move kdoc from header to implementation files
- remove superfluous WARN_ON() after kmalloc()
- WARN_ON(x); if (!x) -> if(!WARN_ON(x))
- improve some comments
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust and honor the vc_scrl_erase_char for 256 and 512 character fonts.
It fixes the issue with disappearing cursor during scrolling
(http://bugzilla.kernel.org/show_bug.cgi?id=11258). The issue was
reported and tracked by Peter Hanzel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time. This allow to create framebuffer
device with larger virtual resolution. Combine with y-panning this can be
used to implement double buffering acceleration method.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Panning in the y-direction can be done by simply changing the DMA base
address. This code is already in place, but FBIOPAN_DISPLAY will
currently fail because ypanstep is 0.
Set ypanstep to 1 to indicate that we do support y-panning and also set
the necessary acceleration flags on AT91 (AVR32 already have them.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy i2c model is going away soon, so switch to the new model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the use of structure templates in i2c-matroxfb. In this case
it's more efficient to initialize the few fields we need individually.
This makes i2c-matroxfb.ko 16% smaller on my system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I broke an error path with d03c21ec0b,
sorry about that.
The machine will crash if the i2c_attach_client() or maven_init_client()
calls fail, although nobody has yet reported this happening.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some chips appear to have the 2D engine hang during screen redraw,
typically in a sequence of copyarea operations. This appear to be
solved by adding a flush of the engine destination pixel cache
and waiting for the engine to be idle before issuing the accel
operation. The performance impact seems to be fairly small.
Here is a trace on an RV370 (PCI device ID 0x5b64), it records the
RBBM_STATUS register, then the source x/y, destination x/y, and
width/height used for the copy:
----------------------------------------
radeonfb_prim_copyarea: STATUS[00000140] src[210:70] dst[210:60] wh[a0:10]
radeonfb_prim_copyarea: STATUS[00000140] src[2b8:70] dst[2b8:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[00000140] src[348:70] dst[348:60] wh[40:10]
radeonfb_prim_copyarea: STATUS[80020140] src[390:70] dst[390:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002613f] src[40:80] dst[40:70] wh[28:10]
radeonfb_prim_copyarea: STATUS[80026139] src[a8:80] dst[a8:70] wh[38:10]
radeonfb_prim_copyarea: STATUS[80026133] src[e8:80] dst[e8:70] wh[80:10]
radeonfb_prim_copyarea: STATUS[8002612d] src[170:80] dst[170:70] wh[30:10]
radeonfb_prim_copyarea: STATUS[80026127] src[1a8:80] dst[1a8:70] wh[8:10]
radeonfb_prim_copyarea: STATUS[80026121] src[1b8:80] dst[1b8:70] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002611b] src[248:80] dst[248:70] wh[68:10]
----------------------------------------
When things are going fine the copies complete before the next ROP is
even issued, but all of a sudden the 2D unit becomes active (bit 17 in
RBBM_STATUS) and the FIFO retry (bit 13) and FIFO pipeline busy (bit
14) are set as well. The FIFO begins to backup until it becomes full.
What happens next is the radeon_fifo_wait() times out, and we access
the chip illegally leading to a bus error which usually wedges the
box. None of this makes it to the console screen, of course :-)
radeon_fifo_wait() should be modified to reset the accelerator when
this timeout happens instead of programming the chip anyways.
----------------------------------------
radeonfb: FIFO Timeout !
ERROR(0): Cheetah error trap taken afsr[0010080005000000] afar[000007f900800e40] TL1(0)
ERROR(0): TPC[595114] TNPC[595118] O7[459788] TSTATE[11009601]
ERROR(0): TPC<radeonfb_copyarea+0xfc/0x248>
ERROR(0): M_SYND(0), E_SYND(0), Privileged
ERROR(0): Highest priority error (0000080000000000) "Bus error response from system bus"
ERROR(0): D-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000]
ERROR(0): D-cache data0[0000000000000000] data1[0000000000000000] data2[0000000000000000] data3[0000000000000000]
ERROR(0): I-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000] u[0000000000000000] l[00\
ERROR(0): I-cache INSN0[0000000000000000] INSN1[0000000000000000] INSN2[0000000000000000] INSN3[0000000000000000]
ERROR(0): I-cache INSN4[0000000000000000] INSN5[0000000000000000] INSN6[0000000000000000] INSN7[0000000000000000]
ERROR(0): E-cache idx[800e40] tag[000000000e049f4c]
ERROR(0): E-cache data0[fffff8127d300180] data1[00000000004b5384] data2[0000000000000000] data3[0000000000000000]
Ker:xnel panic - not syncing: Irrecoverable deferred error trap.
----------------------------------------
Another quirk is that these copyarea calls will not happen until the
first drivers/char/vt.c:redraw_screen() occurs. This will only happen
if you 1) VC switch or 2) run "consolechars" or 3) unblank the screen.
This seems to happen because until a redraw_screen() the screen scrolling
method used by fbcon is not finalized yet. I've seen this with other fb
drivers too.
So if all you do is boot straight into X you will never see this bug on
the relevant chips.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These attributes are really sysdev class attributes. The incorrect
definition leads to an oops because of recent changes which make sysdev
attributes use a different prototype.
Based on Andi's f718cd4add ("sched: make
scheduler sysfs attributes sysdev class devices")
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 51a776fa7a ("rtc: cdev
lock_kernel() pushdown"). The RTC framework does not need BKL
protection.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under rare circumstances, the ehca hardware might erroneously generate
two CQEs for the same WQE, which is not compliant to the IB spec and
will cause unpredictable errors like memory being freed twice. To
avoid this problem, the driver needs to detect the second CQE and
discard it.
For this purpose, introduce an array holding as many elements as the
SQ of the QP, called sq_map. Each sq_map entry stores a "reported"
flag for one WQE in the SQ. When a work request is posted to the SQ,
the respective "reported" flag is set to zero. After the arrival of a
CQE, the flag is set to 1, which allows to detect the occurence of a
second CQE.
The mapping between WQE / CQE and the corresponding sq_map element is
implemented by replacing the lowest 16 Bits of the wr_id with the
index in the queue map. The original 16 Bits are stored in the sq_map
entry and are restored when the CQE is passed to the application.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The idr_find() function may fail when trying to get the QP that is
associated with a CQE, e.g. when a QP has been destroyed between the
generation of a CQE and the poll request for it. In consequence, the
return value of idr_find() must be checked and the CQE must be
discarded when the QP cannot be found.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the ehca driver detects an invalid opcode in a CQE, it currently
passes the CQE to the application and returns with success. This patch
changes the CQE handling to discard CQEs with invalid opcodes and to
continue reading the next CQE from the CQ.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rename the "poll_cq_one_read_cqe" goto label to what it actually does,
namely "repoll".
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the introduction of the port auto-detect mode for ehca, calls to
modify_qp() may be cached in the device driver when the ports are not
activated yet. When a modify_qp() call is cached, the qp state remains
untouched until the port is activated, which will leave the qp in the
reset state. In the reset state, however, it is not allowed to post SQ
WQEs, which confuses applications like ib_mad.
The solution for this problem is to immediately set the qp state as
requested by modify_qp(), even when the call is cached.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Bob Moore