Commit Graph

3612 Commits

Author SHA1 Message Date
Sujith Manoharan 2f8e82e8ab ath9k: Set the TSF adjust value properly
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan 7e52c8aa35 ath9k: Cleanup beacon queue configuration
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan aa45fe9683 ath9k: Remove is_bslot_active
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan ef4ad63368 ath9k: Cleanup beacon logic
* The beaconing status routine is not required, since in
  multi-VIF cases the HW beacon parameters should not be
  re-configured.

* Remove SC_OP_TSF_RESET - when a beaconing interface comes
  up the first time, the TSF has to be reset.

* Simplify ath9k_allow_beacon_config().

* Handle setting/clearing the SWBA interrupt properly.

* Remove the TSF mangling in IBSS mode, it is not required.

* General code cleanup.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 6c43c090a9 ath9k: Simplify ASSOC handling
Cleanup the messy logic dealing with station association
and disassociation.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan df35d29e17 ath9k: Cleanup interface handling
* Do not set/clear TSF when adding/deleting an interface.
  This should be done when the BSS is set up and should also
  take into account the existence of other interfaces.

* Set opmode explicitly.

* ANI setup needs to be decided based on multiple interfaces.
  This can be done via the bss_info_changed() callback.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 60ca9f8744 ath9k_hw: Cleanup ath9k_hw_set_tsfadjust
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 130ef6e9dc ath9k: Fix beacon setup
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:37 -04:00
Felix Fietkau 0f245ed20b ath5k: fix txop limit handling
Same as the recent ath9k fix

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:37 -04:00
Felix Fietkau 08a4a1ab07 ath9k_hw: fix SREV checks for applying tuning caps from EEPROM
AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 3e2ea54328 ath9k_hw: apply XLNA bias settings from EEPROM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 0aefc591be ath9k_hw: clean up AR9003 EEPROM code
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
  access the relevant fields directly

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 89be49e1cd ath9k_hw: apply XPA timing control values from EEPROM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau aa5955c36f ath9k: fix aggregate size limit based on queue TXOP limit
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.

The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.

Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.

Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau 7702e788e7 ath9k: make per-WMM-AC queue sizes configurable via debugfs
Prepare for using different queue size defaults for each AC.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau 531bd07905 ath9k/ath9k_htc: fix txop limit handling
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau a364517b1e ath9k_hw: remove redundant arguments to INIT_INI_ARRAY
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau b05a01110e ath9k_hw: fix tx gain tables for AR934x
Use the EEPROM information to choose the right tx gain table

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 00f97b4fd5 ath9k_hw: enable ANI on AR934x
It has been tested and works properly

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 5d9c7e3c82 ath9k: validate rx antenna settings
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 01967360a2 ath9k_hw: fall back to OTP ROM when platform data has no valid eeprom data
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:33 -04:00
Felix Fietkau 530275e52b ath9k_hw: fix 5 GHz frequency selection on AR934x/AR955x with 25 MHz refclock
The old code was an accidental copy&paste of the 2.4 GHz version,
which doesn't work.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:32 -04:00
Luis R. Rodriguez 00267d591b ath9k: make CONFIG_ATH9K_DFS_CERTIFIED depend on CFG80211_CERTIFICATION_ONUS
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:31 -04:00
Mohammed Shafi Shajakhan 4a17a50d8d ath9k: do not disable hardware while wow is enabled
Hardware needs to be AWAKE and should maintain association
with the AP to process WoW triggers any time

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:17 -04:00
Mohammed Shafi Shajakhan b11e640aef ath9k: Add WoW related mac80211 callbacks
add suspend/resume/set_wakeup callbacks to the driver

*suspend

- bail out only if all the conditions for configuring WoW.
  is fine, currently multivif case is not handled
- check for associated state.
- map wow triggers from user space data.
- add deauth/disassoc pattern and user defined pattern,
  for the later a list is maintained.
- store the interrupt mask before suspend, enabled beacon
  miss interrupt for WoW.
- configure WoW in the hardware by calling ath9k_hw_wow_enable.

*resume

- restore the interrupts based on the interrupt mask
  stored before suspend.
- call ath9k_hw_wow_wakeup to configure/restore the hardware.
- after wow wakeup clear away WoW events and query the
  WoW wakeup reason from the status register

*set_wakeup

- to call 'device_set_wakeup_enable' from cfg80211/mac80211
  when wow is configured and as per Rafael/Johannnes the
  right way to do so rather in the driver suspend/resume
  call back

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:17 -04:00
Mohammed Shafi Shajakhan b3ba6c529b ath: Add Wake-on-Wireless debug mask
to help the developers and users to debug/know
whats happening with WoW

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 64875c63c9 ath9k_hw: Add hardware code for WoW
add a new file wow.c which takes care of the hardware code
for WoW.

*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
	- tracking wow event mask (to suppress spurious
	  wow events)
	- properly configure suspend/resume WAR registers
	- configure PCIE PM control register
	- configure MAC WoW registers and their timeouts
	- enabling wow configuration like magic packet,
	  user patterns based on users configuration
	- configuring timeouts for KAL, beacon miss,
	  aifs, slot time, backoff
	- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
	- primary task is to find the reason for wakeup
	  from the wow status register
	- configure/restore AR_PCIE_PM_CTRL register
	- clear all WoW events
	- configure/restore suspend/resume WAR registers

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 3b604b6cf8 ath9k_hw: INI changes for WoW for AR9002 chipsets
for AR9002 family of chipsets and for WoW sleep, we reprogram
the SerDes so that the PLL and CHK REQ are both enabled. this
uses more power but in certain cases this is required as otherwise
WoW sleep is unstable and chip may disappear.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 9f11e16edc ath9k: advertise supported WoW flags to upper layer
currently the code supports WoW triggers due to
*magic packet
*user defined patterns
*deauth and disassoc patterns
*disconnect - beacon miss, last beacon received timeout,
no ack for keeep alive frames.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan d687809bd8 ath9k_hw: advertise WoW support for capable chipsets
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 8e98138958 ath9k_hw: Add WoW hardware capability flags
have seperate wow capability flags for
*basic wow support
*device capable of matching exact user defined pattern
or de-authentication/disassoc pattern
*device such AR9280 requires first four bytes for
all sort of patterns

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
Mohammed Shafi Shajakhan 01c785338e ath9k: Add definitions and structures to support WoW
*add structures, macros and variables for WoW, so that the driver
can make use of it.
*maintain a list for user enabled patterns and masks
*track pattern slots for the hardware limitation on the
maximum number of patterns that can be stored.
*track interrupts enabled before WoW suspend, so
that can be reconfigured after resume
*have macros to parse user defined wow configurations to
hardware code

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
Mohammed Shafi Shajakhan 900902986c ath9k_hw: Add register definitions for WoW support
*MAC WoW registers

back-off shift, MAC interrupt enable, magic packet enable,
pattern match enable, aifs, slot wait period, keep alive
frame failure count, beacon fail enable, beacon timeout,
keep alive timeout, auto keep alive disable,
keep alive fail disable and their corresponding
status registers. keep alive frame delay,
pattern end/byte offsets, transmit buffers for
keep alive frames and storing the user patterns

*Power Management Control registers

pme_d3cold_vaux, host_pme_enable, aux_pwr_detect,
power_state_mask, wow_pme_clear

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
John W. Linville d07d152892 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
	drivers/net/wireless/iwmc3200wifi/cfg80211.c
	drivers/net/wireless/mwifiex/cfg80211.c
2012-07-12 15:21:05 -04:00
John W. Linville 38a0084063 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-07-12 13:44:50 -04:00
Johannes Berg fd0142844e nl80211: move scan API to wdev
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:41 +02:00
Johannes Berg 84efbb84cf cfg80211: use wireless_dev for interface management
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:08:10 +02:00
Luis R. Rodriguez 2f8684ce7a ath5k: replace modparam_all_channels with CONFIG_ATH5K_TEST_CHANNELS
This stashes away this feature from standard kernel builds.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:40:23 -04:00
Christian Lamparter c9122c0d63 carl9170: fix HT peer BA session corruption
This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.

Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:

 - "stuck" ba sessions and package loss, as the
   stale BAR would reset the sequence each time.

 - lots of reorder releases.

 - ...

Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Reported-by: Mikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: Per-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:38:26 -04:00
Christian Lamparter 4519a74338 carl9170: import 1.9.6 firmware headers
Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:38:26 -04:00
Rajkumar Manoharan d081257c78 ath9k_hw: remove debugging masks from AR_MCI_INTERRUPT_RX_MSG_DEFAULT
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10 12:16:58 -04:00
Mohammed Shafi Shajakhan c32cdbd84f ath9k: Stop the BTCOEX timers before disabling BTCOEX
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:38 -04:00
Mohammed Shafi Shajakhan dd89f05a75 ath9k: Fix MCI cleanup
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now  as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.

Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:37 -04:00
Gabor Juhos 2b943a3315 ath9k: enable support for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:34 -04:00
Gabor Juhos b3d7aa432a ath9k: set 4ADDRESS bit in RX filter for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:34 -04:00
Gabor Juhos c12b60214c ath9k: enable PLL workaround for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:33 -04:00
Gabor Juhos fc05a31784 ath9k: fix PLL initialization for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:32 -04:00
Gabor Juhos 2e2c9cc37e ath9k: skip internal regulator configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:32 -04:00
Gabor Juhos 3b8a0577b7 ath9k: disable SYNC_HOST1_FATAL interrupts for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:31 -04:00
Gabor Juhos db4a3de9db ath9k: fix RF channel frequency configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:30 -04:00
Gabor Juhos 1ed0f8db5b ath9k: fix PAPRD settings for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:30 -04:00
Gabor Juhos 2d00de48ff ath9k: fix antenna control configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:29 -04:00
Gabor Juhos 4b091727ba ath9k: fix XPABIASLEVEL settings for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:28 -04:00
Gabor Juhos 8528f12ed7 ath9k: read spur frequency information from eeprom for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:28 -04:00
Gabor Juhos 8bc45c6bf2 ath9k: add mode register initialization code for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:27 -04:00
Gabor Juhos a0fbb9bd25 ath9k: add initvals for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:26 -04:00
Gabor Juhos 2f8d10fd86 ath9k: enable TX/RX data byte swap for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:26 -04:00
Gabor Juhos c95b584b8d ath9k: clear pciexpress flag for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:25 -04:00
Gabor Juhos 485124cbb7 ath9k: add BB name string for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:25 -04:00
Gabor Juhos 9476f4d636 ath9k: add platform_device_id for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:24 -04:00
Gabor Juhos 813831dc67 ath9k: set MAC version for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:23 -04:00
Gabor Juhos a4e26081cb ath9k: define MAC version for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:23 -04:00
Gabor Juhos b123377935 ath9k: define DEVID for QCA955x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:22 -04:00
Rajkumar Manoharan 83bfea4219 ath9k_hw: fix AR9462 2g5g switch on full reset
On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:20 -04:00
Rajkumar Manoharan 08d4df410a ath9k: fix power consumption on network sleep when BTCOEX is enabled
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:20 -04:00
Rajkumar Manoharan b73f3e7804 ath9k: fix fullsleep power consumption when BTCOEX is enabled
As soon as the interface brought up, btcoex timer starts running
eventhough the interface is in idle state and WLAN chip is moved
to full sleep mode. There is no point in running btcoex timer when
the wlan interface is in sleep mode and also it might consumes
more power on WLAN idle unassociated state. So lets stop the
btcoex when wlan is idle state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:19 -04:00
Rajkumar Manoharan 54717e5330 ath9k_hw: do not load noise floor readings when it is running
Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:18 -04:00
Rajkumar Manoharan 1fe860edb0 ath9k_hw: start noisefloor calibration after MCI reset
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:18 -04:00
Thomas Huehn 1960195725 ath9k: fixing register bit shift values of control packets to support TPC
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.

Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:02 -04:00
Mohammed Shafi Shajakhan c11216d1f6 ath9k: Fix clearing of BTCOEX flags
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.

Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:01 -04:00
John W. Linville 0af5491c2f Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next 2012-07-09 16:34:39 -04:00
John W. Linville 635d999fd3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	net/mac80211/mlme.c
2012-07-09 16:34:34 -04:00
Johannes Berg 71bbc99438 cfg80211: use wdev in mgmt-tx/ROC APIs
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:51:47 +02:00
Thomas Huehn e3e1a0bcb3 mac80211: reduce IEEE80211_TX_MAX_RATES
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.

The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.

Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-03 13:48:37 +02:00
John W. Linville 8732baafc3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
	drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
2012-06-29 12:42:14 -04:00
John W. Linville 42fb0b0278 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-06-29 12:07:37 -04:00
David S. Miller b26d344c6b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/caif/caif_hsi.c
	drivers/net/usb/qmi_wwan.c

The qmi_wwan merge was trivial.

The caif_hsi.c, on the other hand, was not.  It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.

I did my best with that one and will ask Sjur to check it out.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28 17:37:00 -07:00
Felix Fietkau 469979173e ath9k: de-duplicate initvals
The initvals tool from https://github.com/mcgrof/qca-swiss-army-knife has
been modified to detect identical initval tables and replace them with
macros. This patch contains the generated changes.

On MIPS this reduces the binary size by 24 KB with no runtime changes.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:47 -04:00
Felix Fietkau 589ebd8526 ath9k: update AR934x initvals to latest version
Generated using the initvals tool from the qca-swiss-army-knife repository
from https://github.com/mcgrof/qca-swiss-army-knife

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:47 -04:00
Mohammed Shafi Shajakhan d8fffb4a9e ath9k: Fix signedness in a MCI debug message
seems i got a message like this
ath: phy0: BT_Status_Update: is_link=0, linkId=2,
state=1, SEQ=-2085766476 initially.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Mohammed Shafi Shajakhan 812944891c ath9k_hw: make use of the wrapper to check for MCI init
ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Felix Fietkau 73dc3eb8b9 ath9k: fix ANI operation in AP mode
ath9k_ani_reset (which is called at reset time) uses a state variable
ani->update_ani to prevent the ANI noise immunity state on the operating
channel from being overwritten by background scans. Unfortunately this
is also being set for AP mode, since it's mixed with code that is only
supposed to change the default settings after a reset.

In AP mode this has the side effect of having ANI run, but being unable to
change its runtime noise immunity level, making it effectively useless.

Fix this by getting rid of ani->update_ani and passing a parameter to
ath9k_hw_set_ofdm_nil and ath9k_hw_set_cck_nil instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Johannes Berg b1fbd46976 Merge remote-tracking branch 'wireless-next/master' into mac80211-next 2012-06-28 13:45:58 +02:00
Sujith Manoharan bf52592fe4 ath9k: Fix compilation breakage
Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.

Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 15:23:19 -04:00
Tom Hughes 6bb51c70ca ath9k: fix panic caused by returning a descriptor we have queued for reuse
Commit 3a2923e83c introduced a bug when a corrupt descriptor
is encountered - although the following descriptor is discarded
and returned to the queue for reuse the associated frame is
also returned for processing. This leads to a panic:

BUG: unable to handle kernel NULL pointer dereference at 000000000000003a
IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k]
Call Trace:
<IRQ>
[<ffffffff812d7fa0>] ? map_single+0x60/0x60
[<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k]
[<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k]
[<ffffffff8105e133>] tasklet_action+0x63/0xd0
[<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0
[<ffffffff8101a873>] ? native_sched_clock+0x13/0x80
[<ffffffff815f9d5c>] call_softirq+0x1c/0x30
[<ffffffff810151f5>] do_softirq+0x75/0xb0
[<ffffffff8105df95>] irq_exit+0xb5/0xc0
[<ffffffff815fa5b3>] do_IRQ+0x63/0xe0
[<ffffffff815f0cea>] common_interrupt+0x6a/0x6a
<EOI>
[<ffffffff8131840a>] ? intel_idle+0xea/0x150
[<ffffffff813183eb>] ? intel_idle+0xcb/0x150
[<ffffffff814a1db9>] cpuidle_enter+0x19/0x20
[<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240
[<ffffffff8101c4bf>] cpu_idle+0xaf/0x120
[<ffffffff815cda8e>] rest_init+0x72/0x74
[<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4
[<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e
[<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135
[<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f

Making sure bf is cleared to NULL in this case restores the
old behaviour.

Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 14:48:13 -04:00
Panayiotis Karabassis 7508b65796 ath9k: enable serialize_regmode for non-PCIE AR9287
https://bugzilla.kernel.org/show_bug.cgi?id=42903

Based on the work of <fynivx@gmail.com>

Signed-off-by: Panayiotis Karabassis <panayk@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 14:48:12 -04:00
Johannes Berg dfb89c56ad cfg80211: don't allow WoWLAN support without CONFIG_PM
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.

Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-27 17:55:11 +02:00
Sujith Manoharan 6bcfe67f98 ath9k_htc: Fix IDLE power save
Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:52 -04:00
Sujith Manoharan d8a2c51cdc ath9k_htc: Use atomic operations for op_flags
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sujith Manoharan fb1c078edb ath9k_htc: Change default listen interval to 1
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sujith Manoharan fad29cd2f5 ath9k: Fix lockdep splat
Cancel the MCI work only when MCI is actually enabled.
Fixes this:

[96833.124051] Call Trace:
[96833.124060]  [<ffffffff810afaf8>] __lock_acquire+0x1518/0x1e40
[96833.124065]  [<ffffffff810ad126>] ? mark_held_locks+0x86/0x110
[96833.124069]  [<ffffffff810ad3ad>] ? trace_hardirqs_on+0xd/0x10
[96833.124073]  [<ffffffff814464f0>] ? _raw_spin_unlock_irq+0x30/0x70
[96833.124078]  [<ffffffff81072968>] ? wait_on_cpu_work+0x98/0xc0
[96833.124082]  [<ffffffff810b0a11>] lock_acquire+0xa1/0x150
[96833.124085]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124088]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124092]  [<ffffffff810729e2>] wait_on_work+0x52/0x120
[96833.124095]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124099]  [<ffffffff81063b3f>] ? del_timer+0x7f/0x110
[96833.124102]  [<ffffffff81072c13>] __cancel_work_timer+0x83/0x130
[96833.124106]  [<ffffffff81072cf0>] cancel_work_sync+0x10/0x20
[96833.124113]  [<ffffffffa065b5cd>] __ath_cancel_work+0x4d/0x60 [ath9k]
[96833.124119]  [<ffffffffa065cf28>] ath9k_config+0x458/0x680 [ath9k]
[96833.124125]  [<ffffffffa065dd1e>] ? ath9k_flush+0x6e/0x1d0 [ath9k]
[96833.124129]  [<ffffffff8144394d>] ? __mutex_unlock_slowpath+0x10d/0x190
[96833.124146]  [<ffffffffa056c7b5>] ieee80211_hw_config+0x135/0x2a0 [mac80211]
[96833.124163]  [<ffffffffa057ebbb>] ieee80211_do_open+0x67b/0xc50 [mac80211]
[96833.124178]  [<ffffffffa057f1fd>] ieee80211_open+0x6d/0x80 [mac80211]
[96833.124183]  [<ffffffff8137a44f>] __dev_open+0x9f/0xf0
[96833.124187]  [<ffffffff8137a701>] __dev_change_flags+0xa1/0x180
[96833.124190]  [<ffffffff8137a898>] dev_change_flags+0x28/0x70
[96833.124195]  [<ffffffff813e1179>] devinet_ioctl+0x659/0x780
[96833.124199]  [<ffffffff8137aea0>] ? dev_ioctl+0x210/0x6d0
[96833.124203]  [<ffffffff813e1db5>] inet_ioctl+0x75/0x90
[96833.124208]  [<ffffffff8135e0e0>] sock_do_ioctl+0x30/0x70
[96833.124211]  [<ffffffff8135e3dd>] sock_ioctl+0x7d/0x2c0
[96833.124218]  [<ffffffff81193c39>] do_vfs_ioctl+0x99/0x580
[96833.124222]  [<ffffffff81447415>] ? sysret_check+0x22/0x5d
[96833.124226]  [<ffffffff811941b9>] sys_ioctl+0x99/0xa0
[96833.124230]  [<ffffffff814473e9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sven Eckelmann 313eb87f1e ath9k: raise aggregation limit to 64k for HT IBSS
mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.

This patch changes this to update ampdu factor/density settings
when starting a blockack session.

Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:50 -04:00
David S. Miller e486463e82 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/usb/qmi_wwan.c
	net/batman-adv/translation-table.c
	net/ipv6/route.c

qmi_wwan.c resolution provided by Bjørn Mork.

batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.

ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-25 15:50:32 -07:00
Felix Fietkau bed3d9c0b7 ath9k: fix dynamic WEP related regression
commit 7a532fe713
ath9k_hw: fix interpretation of the rx KeyMiss flag

This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.

This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.

Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-25 15:14:13 -04:00
Rajkumar Manoharan 4b5237cc86 ath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck
drivers/net/wireless/ath/ath9k/ar9003_phy.c:211
ar9003_hw_spur_mitigate_mrc_cck() error: potential NULL dereference
'spur_fbin_ptr'.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-22 14:44:06 -04:00
Rajkumar Manoharan 81b67fd60a ath9k_hw: rename mrcCCKOff to fix smatch warning
Rename mrcCCKOff for better code readability and also fixes
the smatch warning.

drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
	ar9003_hw_ani_control() Error invalid range 1 to 0.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-22 14:44:05 -04:00
Rajkumar Manoharan 5039f38e16 ath9k: do not sampling on ani timer when chip is in sleep
The baseband and cycle counters are being sampled during ani
processing for debugging purpose. Whenever the ani is postponded
due to sleep state, taking samples on that time is of no use and
also unneccesarily waking up the chip might increase the power
consumption on idle associated state. Hence moving debug function
within powersave block.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:56 -04:00
Rajkumar Manoharan 4ff6a9d200 ath9k_hw: fix LNA control on WLAN sleep
When WLAN enter full sleep mode, WLAN HW should send out a LNA_TAKE
message for BT to take control of the shared LNA. Otherwise BT traffic
is completely stopped whenever the wlan interface is moved full sleep
mode.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:54 -04:00
Rajkumar Manoharan 0967d86231 ath9k_hw: update ar9462 dac_async_fifo initval
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:52 -04:00
Rajkumar Manoharan e1ecad78e5 ath9k: fix mci_is_enabled utility
During driver stop, btcoex is disabled and also btcoex_hw.enabled
is set to false. Afterwards mci_is_enabled returns false so that
BT is not gaining SPDT control on WLAN sleep. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:51 -04:00
Rajkumar Manoharan a68807e917 ath9k_hw: fix BT mute at hw init
WLAN driver initialization is muting BT which is terminating
the ongoing BT traffic. The reason to mute BT is to avoid any
incoming MCI messages from BT when MCI reset is in progress that
could corrupt WLAN MCI RX state machine. But we should not
dedicate radio completely to WLAN in driver init itself. So this
patch removes the wlan weightage changes from mute BT to retain
BT connection.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:49 -04:00
Bala Shanmugam 305dd09f8c ath9k: fix incorrect profile type manupulation
Two MCI interrupts are generated while adding A2DP and headset profiles
with different types and same connection handle. While disconnecting,
only one MCI interrupt is generated with last added profile type value
for both profiles.

While adding second profile type decrement first one.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:47 -04:00
Felix Fietkau 058a6385cb ath9k_hw: clean up ANI OFDM trigger handling
Adjust ah->config.ofdm_trig_{high,low} when setting noise immunity values
to simplify threshold checks in ath9k_hw_ani_monitor

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:44 -04:00
Felix Fietkau 1e8f0a317b ath9k_hw: fix setting lower noise immunity values
Commit af1e8a6f "ath9k: reset noiseimmunity level to default" was supposed
to ensure that the default noise immunity level is above the INI
values, however it prevents setting lower noise immunity values altogether.
Fix this by moving the checks to the right function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:43 -04:00
Felix Fietkau 198823fd00 ath9k: remove MIB interrupt support
The new ANI implementation does not need it

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:43 -04:00
Felix Fietkau 465dce62cd ath9k_hw: clean up defines and variables from the ANI implementation split
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:43 -04:00
Felix Fietkau 6790ae7a13 ath9k_hw: remove the old ANI implementation
It was found to be buggy on a variety of chipsets from AR913x to AR928x.
The new version (which was introduced along with AR93xx support) is more
reliable in preventing connectivity dropouts and also fixes MIB interrupt
storm issues.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:42 -04:00
Felix Fietkau 5330df7b17 ath9k_hw: clean up / fix ANI mode checks related to beacon RSSI
Beacon RSSI is only meaningful in station mode - in ad-hoc mode it
fluctuates, depending on which peer last sent a beacon, and in other
modes it is not set at all.
Fix places in ANI where the beacon RSSI is used to limit their use
to station mode only.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:42 -04:00
Felix Fietkau 7067e7014d ath9k_hw: remove confusing logic inversion in an ANI variable
Code using this had already triggered smatch complaints, so remove it before
it gets fixed the wrong way.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:42 -04:00
Felix Fietkau 0b81cc3922 ath9k_hw: fix OFDM weak signal detection handling
Commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
was unifying some code related to overriding OFDM weak signal detection,
but seems to have gotten some of the original intent wrong, probably
because of a misnamed variable.

The beacon RSSI is only valid in station mode, and the main reason to check
it in ath9k_hw_set_ofdm_nil is to make sure that OFDM weak signal detection
stays enabled if the RSSI is low, even when the OFDM noise immunity entry
is supposed to disable it.

The above commit removed the mode checks and changed the code so that
OFDM weak signal detection would only be changed if the rssi is high, which
is wrong for everything but client mode.

This patch restores the old behavior in a simplified form.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:41 -04:00
Felix Fietkau 35e808b7e4 ath9k_hw: remove aniState->noiseFloor
I don't know why somebody decided to keep a cached copy of beacon rssi in a
variable called 'noiseFloor', but the caching is unnecessary and the variable
name is confusing, so let's just get rid of it entirely.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:44:41 -04:00
Rajkumar Manoharan 931cb03afe ath9k_htc: configure bssid on ASSOC/IBSS change
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.

Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:10:26 -04:00
Mohammed Shafi Shajakhan f18e3c6b67 ath9k_hw: avoid possible infinite loop in ar9003_get_pll_sqsum_dvc
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).

Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 14:10:25 -04:00
Bob Copeland 6617942e15 ath5k: remove _bh from inner locks
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here.  Fixes smatch warnings:

   drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
   drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'

Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19 14:56:25 -04:00
Felix Fietkau 80b08a8d88 ath9k: fix invalid pointer access in the tx path
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.

This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19 14:56:24 -04:00
Felix Fietkau 76591bea97 ath9k: fix a tx rate duration calculation bug
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-19 14:56:24 -04:00
John W. Linville b3c911eeb4 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
	drivers/net/wireless/iwlwifi/dvm/testmode.c
	drivers/net/wireless/iwlwifi/pcie/trans.c
2012-06-19 14:41:22 -04:00
Kalle Valo d987dd137b Merge remote branch 'wireless-next/master' into ath6kl-next
Conflicts:
	drivers/net/wireless/ath/ath6kl/cfg80211.c
2012-06-14 14:44:49 +03:00
Thomas Pedersen c85251f856 ath6kl: fix fw capability parsing
This patch fixes a bug where no capabilites are parsed when the number
of firmware capability bits translate into fewer bytes than the host has
knowledge of. Instead just process number of capability bytes as
reported by the firmware.

Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-14 13:54:42 +03:00
John W. Linville 211c17aaee Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/ath/ath9k/main.c
	net/bluetooth/hci_event.c
2012-06-13 15:35:35 -04:00
Rajkumar Manoharan 9330969b8f ath9k_hw: remove MCI_STATE_SET_BT_SLEEP
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:02 -04:00
Rajkumar Manoharan 26e942b790 ath9k_hw: remove MCI_STATE_CONT_* state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:02 -04:00
Rajkumar Manoharan 6d97be48e2 ath9k_hw: remove MCI_STATE_BT
remove MCI_STATE_BT and use bt_state instead.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:01 -04:00
Rajkumar Manoharan b98ccec0a4 ath9k_hw: remove p_data argument from ar9003_mci_state
As p_data is unuse, lets remove it from ar9003_mci_state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:00 -04:00
Rajkumar Manoharan d02ca07e6f ath9k_hw: remove MCI_STATE_NEED_FLUSH_BT_INFO
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:00 -04:00
Rajkumar Manoharan 2d340ac81e ath9k_hw: remove MCI_STATE_SEND_WLAN_CHANNELS
Add a MCI util function to send wlan channel info to BT.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:59 -04:00
Rajkumar Manoharan e1763d3f33 ath9k_hw: add utility function to set BT version
Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:58 -04:00
Rajkumar Manoharan 506847ad34 ath9k_hw: cleanup MCI gpm offset state
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:58 -04:00
Mohammed Shafi Shajakhan 64bc1239c7 ath9k: Fix softlockup in AR9485
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up

	Call Trace:
	[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
	[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
	[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
	[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
	[<ffffffff810744fe>] process_one_work+0x11e/0x470
	[<ffffffff8107530f>] worker_thread+0x15f/0x360
	[<ffffffff810751b0>] ? manage_workers+0x230/0x230
	[<ffffffff81079af3>] kthread+0x93/0xa0
	[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
	[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
	[<ffffffff815fd3a0>] ? gs_change+0x13/0x13

ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.

fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142

Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:57 -04:00
Rajkumar Manoharan a197b76c23 ath9k: fix btcoex duty cycle
* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
  reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:57 -04:00
Rajkumar Manoharan 3c7992e33a ath9k: defer btcoex scheme update
As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:56 -04:00
Rajkumar Manoharan dfd0587a7d ath9k: keep btcoex period in milliseconds
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:56 -04:00
Rajkumar Manoharan 9e2e0c8469 ath9k: simplify btcoex profile management
This patch simplifies profile management utility functions.

* Separate find_profile from add/del functions
* Return correct values when the profile list is empty or
  profile is ot found
* flush the profiles when there are entries in the list

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:55 -04:00
Rajkumar Manoharan 92a33298e9 ath9k_hw: process MCI interrupts only when btcoex is enabled
let us process MCI interrupts only when BTCOEX is enabled to avoid
processing bogus interrupts.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:54 -04:00
Rajkumar Manoharan ed6ebd8bc8 ath9k_hw: program OBS register only when MCI is disabled
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:54 -04:00
Rajkumar Manoharan 1bde95fa7e ath9k_hw: fix incorrect LNA register settings
After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:53 -04:00
Rajkumar Manoharan 3863495b86 ath9k_hw: check GPM HW write pointer before chip reset
Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:53 -04:00
Rajkumar Manoharan 9dd9b0dc1d ath9k_hw: Fix AR9462 power consumption on idle associated
The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:52 -04:00
Rajkumar Manoharan 8389fb3fd7 ath9k: restore power state on set channel failure
Not doing so, could cause imbalance in powersave count.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:51 -04:00
Rajkumar Manoharan cec429dd65 ath9k: choose legacy rate as last rate of MRR series
Choose legacy rate as the last rate of Multi Rate Retry series
if and only if the last selected rate is MCS and having higher
PER rate. The current code fills a legacy rate as last one even
though the previous rates in the series are having good PER value.
This could limit the aggregation that affects the uplink performance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:51 -04:00
Sujith Manoharan 6304c20167 ath9k_hw: Update initvals for AR9462
Adjust quick_drop value in the baseband AGC register to
improve RX in HT20 mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:50 -04:00
Mohammed Shafi Shajakhan bcb7ad7bcb ath9k: Fix softlockup in AR9485
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up

	Call Trace:
	[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
	[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
	[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
	[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
	[<ffffffff810744fe>] process_one_work+0x11e/0x470
	[<ffffffff8107530f>] worker_thread+0x15f/0x360
	[<ffffffff810751b0>] ? manage_workers+0x230/0x230
	[<ffffffff81079af3>] kthread+0x93/0xa0
	[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
	[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
	[<ffffffff815fd3a0>] ? gs_change+0x13/0x13

ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.

fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142

Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:09:48 -04:00
John W. Linville 0440507bbc Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-06-12 14:25:04 -04:00
Sujith Manoharan cba63e99e5 ath9k_hw: Initvals update for AR9462
MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11 14:59:44 -04:00
Mohammed Shafi Shajakhan a23415fd7e ath9k: remove incompatible IBSS interface check in change_iface
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.

this patch is dependent on 'cfg80211: fix interface combinations'

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11 14:29:14 -04:00
Mohammed Shafi Shajakhan 2031b4c2b4 ath9k: Fix a WARNING on suspend/resume with IBSS
this patch is dependent on the patch "cfg80211: fix interface
combinations"

In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC.  we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.

The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.

        ath: phy0: Cannot create ADHOC interface when other
        interfaces already exist.
        WARNING: at net/mac80211/driver-ops.h:12
        ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
        Hardware name: 2842RK1
        wlan2:  Failed check-sdata-in-driver check, flags: 0x0

        Call Trace:
        [<c01361b2>] warn_slowpath_common+0x72/0xa0
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<c0136283>] warn_slowpath_fmt+0x33/0x40
        [<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
        [<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
        [<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
        [<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]

Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11 14:29:14 -04:00
Naveen Singh b5b6f6a9a0 ath6kl: use firmware version from FW IE
Need to have different FW versioning for different FW binaries.
This is handled by appending different meta data in firmware
binaries.

kvalo: add an empty line before a debug message, use '0' instead of '0x00',
fix indentation

Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-11 16:18:03 +03:00
Vasanthakumar Thiagarajan 7940bad508 ath6kl: Fix unstable downlink throughput
There is frequent downlink throughput drop to 0 when operating
at the signal level between -42dBm to -53dBm. This has been root
caused to the delay in releasing pending a-mpdu subframes in
reorder buffer. Right now the timeout value is 400ms, there
is also a race condition where timeout handler can be delayed
to run at an extra timeout interval. This patch reduces the
timout interval to reasonable 100ms and makes sure releasing
pending frames are not skipped in the timeout handler by removing
the flag (rxtid->progress) which can delay the timeout logic.

Reported-by: Yu Yanzhi <yanzhiy@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-11 16:13:41 +03:00
Vasanthakumar Thiagarajan 0faf745872 ath6kl: Fix race in aggregation reorder logic
There are many places where tid data are accessed without
the lock (rxtid->lock), this can lead to a race condition
when the timeout handler for aggregatin reorder and the
receive function are getting executed at the same time.
Fix this race, but still there are races which can not
be fixed without rewriting the whole aggregation reorder
logic, for now fix the obvious ones.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-11 16:13:41 +03:00
Etay Luz d154f32ebe ath6kl: support changing dtim period on AP mode
This patch adds support for dtim_period configuration in beacon.

kvalo: add a comment about ignoring the error, use vif_idx,
add \n to the warning message

Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-11 16:08:13 +03:00
Joe Perches f1ff32e8a8 ath6kl: Add missing newline terminations
Messages without newlines can be interleaved.
Avoid this by adding terminations.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-06-11 16:05:42 +03:00
Sujith Manoharan 196fb860ce ath9k: Resync beacons properly
After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan 07c15a3ffd ath9k: Fix powersave locking
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan b74713d04e ath9k: Handle fatal interrupts properly
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately.  Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan 781b14a315 ath9k: Use atomic operations
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan 8da07830e1 ath9k: Move LNA code to antenna.c
And use a helper function to setup antennae after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan af68abadac ath9k: Fix work handling
* Currently, there is no synchronization between the reset
  work and the tx-poll work. Fix this and make sure that we
  bail out properly if a reset work is in progress.

* Cleanup the PLL WAR and enable it for AR9340 too and
  use a helper for restarting work/timers after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Sujith Manoharan ef1b6cd9a1 ath9k: Group link monitoring logic
Add link.c and move all the link/connection monitoring
code to it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan 6995fb805e ath9k: improve BT FTP/PAN performance
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan 153dccd467 ath9k_hw: fix power state for MCI
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan c9ae6ab4c7 ath: do not update cycle counters with sleep mode
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan 0603143e47 ath9k: BT coex performance tuning for AR9462
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan 99922a45e9 ath9k_hw: fix BT RF performance
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan c8b6fbe1f1 ath9k_hw: configure ar9462 switching regulator
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 9dc08eceb7 ath9k_hw: program BT to control SPDT
program BT to control SPDT everytime while loading switch table
from eeprom.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 4fb7175bbd ath9k_hw: fix IQ calibration chain index
The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 4f6bd1a8df ath9k: cleanup MCI indentation
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Rajkumar Manoharan 5d294a1680 ath9k_hw: update ar9462 initval table to fix rx
The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Sujith Manoharan e6930c4b32 ath9k: Use separate operational flags for BTCOEX
Also, use atomic operations to check the flags.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 4cb54fa3a2 ath9k: Remove SC_OP_OFFCHANNEL
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 2fd5d35bc8 ath9k_hw: Fix variable usage
Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 97ba515a20 ath9k: Add MCI interrupt to debugfs statistics
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan 31604cf0a7 ath9k_hw: Cleanup power mode API
The 'setChip' variable is unused, remove it and
simplify the functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan 5955b2b0ef ath9k_hw: Fix MCI usage
MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan 83c7a52dcc ath9k_hw: Fix AR_RTC_KEEP_AWAKE usage
The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan e270e776a0 ath9k: Setup MCI interrupts properly
MCI interrupts have to be enabled only when BTCOEX is
actually in use.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan d09f5f4cfb ath9k: Handle ASPM properly
ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:24 -04:00
Sujith Manoharan aaa1ec46b3 ath9k: Prune ath9k_init_device
Instead of cluttering ath9k_init_device() with 'ath_softc'
specific initialization code, use ath9k_init_softc() to
setup driver-specific work routines, timers etc.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:23 -04:00
Vivek Natarajan d202caff28 ath9k: Ensure a fair beacon distribution in IBSS mode
Configure CWmin based on slot time for IBSS mode. This helps
in increasing the beacon distribution of ath9k to accepted
levels in 11a mode.

Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:19:00 -04:00
Zefir Kurtisi 620a55687b ath9k: fix/add bits for spectral scanning
Updates for spectral scanning register modification for AR93x:
 * fix bits for spectral_scan_count
 * add bits for new parameters

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:18:18 -04:00
Joe Perches 2c208890c6 wireless: Remove casts to same type
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.

For example, this cast:

        int y;
        int *p = (int *)&y;

I used the coccinelle script below to find and remove these
unnecessary casts.  I manually removed the conversions this
script produces of casts with __force, __iomem and __user.

@@
type T;
T *p;
@@

-       (T *)p
+       p

Neatened the mwifiex_deauthenticate_infra function which
was doing odd things with array pointers and not using
is_zero_ether_addr.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06 09:31:33 -07:00
Johannes Berg aa430da410 cfg80211: provide channel to start_ap function
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.

This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.

Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:16 -04:00
Ben Greear b90bd9d14f ath9k: Support ethtool getstats api.
This returns many of the values that formerly could
only be obtained from debugfs.  This should be an
improvement when trying to access these counters
programatically.  Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:10 -04:00
Mohammed Shafi Shajakhan d25360b190 ath9k: Fix modal EEPROM dump
we provide excess buffer size for 'simple_read_from_buffer'
for modal EEPROM dump. This results in trailing NULL bytes
at the end of EEPROM dump, fix this.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Holger Schurig <holgerschurig@gogglemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:23:20 -04:00
John W. Linville a0f68763e1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem 2012-05-30 10:32:16 -04:00
Kiran Reddy 67b3f1299a ath6kl: separate ht cap for each band
In virtual interface structure, for each band separate ht cap
is needed. so that one can disable or enable ht capability band
wise.
This will fix the following issue:

1) Disable 11n from supplicant and start a P2P GO.
2) In beacon frames no HT-CAP IE is seen which is expected.
3) Now remove the P2P GO and kill the supplicant.
4) Beacon stops
5) Now using iw  associate to an external AP in 5 GHZ
6) In 5 GHZ no HT IE going in assoc request but
when  associated in 2.4 GHZ can see HT IES over the air
in assoc request.

In the code for del_beacon in cfg80211.c,set_ht_cap is being
called first for 2.4 GHZ and then for 5 GHZ. When  called
for the first time for 2.4 GHZ the enable flag will be set to true
and so when called for the second time for 5 GHZ it just returns
after checking the flag.

Also using this one can have different HT capabilities
per band (for example one may decide not to use 20/40 in 2.4 GHZ
but use it in 5 GHZ). So maintaining a single context is not ok.
it is true for even the enable/disable flag and other HT
capabilities as well

Signed-off-by: Kiran Reddy <c_lreddy@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-30 08:23:56 +03:00
Felix Fietkau bfc441a4bb ath9k_hw: apply internal regulator settings on AR933x
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-29 13:45:23 -04:00
Felix Fietkau 5a71f13402 ath9k_hw: update AR933x initvals to fix issues with high power devices
"> Can you provide more information about the issues with high power devices?
Tx being flakey and Rx not working at all."

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-29 13:45:22 -04:00
Felix Fietkau 81357a281d ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath_tx_setup_buffer() can fail if there is no ath_buf left, or if mapping DMA
failed. In this case it frees the skb passed to it.
If ath_tx_setup_buffer is called from ath_tx_form_aggr, the skb is still
linked into the tid buffer list and must be dequeued before being released.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-29 13:45:22 -04:00
Felix Fietkau ceea2a5196 ath9k: stop rx dma before stopping tx
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-29 13:45:22 -04:00
Felix Fietkau 9b4760e301 ath5k: add possible wiphy interface combinations
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
2012-05-29 13:42:45 -04:00
Raja Mani df6a7072ac ath6kl: Fix typo in htc mbox debug print msg
Add missing ZERO (x%x to 0x%x) in the format specifier
while printing hex value in htc module.

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-29 14:21:25 +03:00
Raja Mani 824174c3b5 ath6kl: Remove unneeded memset in roam related config func
No need to clear requested memory after allocating new SKB
with help of ath6kl_wmi_get_new_buf(). This clear part is
already taken care in ath6kl_wmi_get_new_buf().

Found this on code review.

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-29 14:21:22 +03:00
Linus Torvalds 28f3d71761 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull more networking updates from David Miller:
 "Ok, everything from here on out will be bug fixes."

1) One final sync of wireless and bluetooth stuff from John Linville.
   These changes have all been in his tree for more than a week, and
   therefore have had the necessary -next exposure.  John was just away
   on a trip and didn't have a change to send the pull request until a
   day or two ago.

2) Put back some defines in user exposed header file areas that were
   removed during the tokenring purge.  From Stephen Hemminger and Paul
   Gortmaker.

3) A bug fix for UDP hash table allocation got lost in the pile due to
   one of those "you got it..  no I've got it.." situations.  :-)

   From Tim Bird.

4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
   try to coalesce overlapping frags and crash.  Fix from Eric Dumazet.

5) RCU routing table lookups can race with free_fib_info(), causing
   crashes when we deref the device pointers in the route.  Fix by
   releasing the net device in the RCU callback.  From Yanmin Zhang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
  tcp: take care of overlaps in tcp_try_coalesce()
  ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
  mm: add a low limit to alloc_large_system_hash
  ipx: restore token ring define to include/linux/ipx.h
  if: restore token ring ARP type to header
  xen: do not disable netfront in dom0
  phy/micrel: Fix ID of KSZ9021
  mISDN: Add X-Tensions USB ISDN TA XC-525
  gianfar:don't add FCB length to hard_header_len
  Bluetooth: Report proper error number in disconnection
  Bluetooth: Create flags for bt_sk()
  Bluetooth: report the right security level in getsockopt
  Bluetooth: Lock the L2CAP channel when sending
  Bluetooth: Restore locking semantics when looking up L2CAP channels
  Bluetooth: Fix a redundant and problematic incoming MTU check
  Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
  Bluetooth: Fix EIR data generation for mgmt_device_found
  Bluetooth: Fix Inquiry with RSSI event mask
  Bluetooth: improve readability of l2cap_seq_list code
  Bluetooth: Fix skb length calculation
  ...
2012-05-24 11:54:29 -07:00
Bala Shanmugam 06e360ace9 ath6kl: Add support for setting tx rateset.
Tx legacy and mcs rateset can configured using iw for
2.4 and 5 bands.  Add support for the same in driver.

kvalo: add an enum for the hw flags and rename the flag accordingly,
rename ath6kl_cfg80211_set_bitrate_mask() to a shorter version to make
it easier to indent

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-24 10:22:22 +03:00
Vasanthakumar Thiagarajan fa338be062 ath6kl: Fix missing gpio pin 9 configuration
GPIO pin 9 also needs to be configured along with other gpio
pins to avoid sdio crc errors. I've not experienced any issue
with missing this particular gpio pin configuration, found dunring
code review. This can potentially improve rx performance.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-24 10:11:06 +03:00
Linus Torvalds a481991467 USB 3.5-rc1 pull request
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
 
 It's touches a lot of different parts of the kernel, all USB drivers,
 due to some API cleanups (getting rid of the ancient err() macro) and
 some changes that are needed for USB 3.0 power management updates.
 
 There are also lots of new drivers, pimarily gadget, but others as well.
 We deleted a staging driver, which was nice, and finally dropped the
 obsolete usbfs code, which will make Al happy to never have to touch
 that again.
 
 There were some build errors in the tree that linux-next found a few
 days ago, but those were fixed by the most recent changes (all were due
 to us not building with CONFIG_PM disabled.)
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
 3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
 =4jM1
 -----END PGP SIGNATURE-----

Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
 "Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.

  It's touches a lot of different parts of the kernel, all USB drivers,
  due to some API cleanups (getting rid of the ancient err() macro) and
  some changes that are needed for USB 3.0 power management updates.

  There are also lots of new drivers, pimarily gadget, but others as
  well.  We deleted a staging driver, which was nice, and finally
  dropped the obsolete usbfs code, which will make Al happy to never
  have to touch that again.

  There were some build errors in the tree that linux-next found a few
  days ago, but those were fixed by the most recent changes (all were
  due to us not building with CONFIG_PM disabled.)

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
  xhci: Fix DIV_ROUND_UP compile error.
  xhci: Fix compile with CONFIG_USB_SUSPEND=n
  USB: Fix core compile with CONFIG_USB_SUSPEND=n
  brcm80211: Fix compile error for .disable_hub_initiated_lpm.
  Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
  MAINTAINERS: Add myself as maintainer to the USB PHY Layer
  USB: EHCI: fix command register configuration lost problem
  USB: Remove races in devio.c
  USB: ehci-platform: remove update_device
  USB: Disable hub-initiated LPM for comms devices.
  xhci: Add Intel U1/U2 timeout policy.
  xhci: Add infrastructure for host-specific LPM policies.
  USB: Add macros for interrupt endpoint types.
  xhci: Reserve one command for USB3 LPM disable.
  xhci: Some Evaluate Context commands must succeed.
  USB: Disable USB 3.0 LPM in critical sections.
  USB: Add support to enable/disable USB3 link states.
  USB: Allow drivers to disable hub-initiated LPM.
  USB: Calculate USB 3.0 exit latencies for LPM.
  USB: Refactor code to set LPM support flag.
  ...

Conflicts:
	arch/arm/mach-exynos/mach-nuri.c
	arch/arm/mach-exynos/mach-universal_c210.c
	drivers/net/wireless/ath/ath6kl/usb.c
2012-05-22 15:50:46 -07:00
John W. Linville a0d0d1685f Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next 2012-05-22 15:18:06 -04:00
Sarah Sharp e1f12eb6ba USB: Disable hub-initiated LPM for comms devices.
Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-18 15:42:55 -07:00
Thomas Pedersen 33a6664a6e ath6kl: issue wmi disconnect after notifying cfg80211
ath6kl would issue a wmi disconnect command in response to a remote
disconnect and return early without notifying cfg80211, only sending a
cfg80211_disconnected (with reason code always 3) in response to the
second disconnect firmware event.

Pass the right reason code to cfg80211 on the first disconnect instead.

This fixes at least one bug where a p2p client would stop trying to
connect after receiving a stale RSN deauth which was reported to
cfg80211 as GO leaving BSS.

Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-05-17 09:10:46 +03:00