Commit Graph

3612 Commits

Author SHA1 Message Date
Johannes Berg e548c49e6d mac80211: add key flag for management keys
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-09-10 11:29:17 +02:00
John W. Linville fac805f8c1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-09-07 15:07:55 -04:00
Sujith Manoharan adfbda6224 ath9k: Fix TX filter usage
The TX filter bit for a station would be set by the HW
when a frame is not acked. A frame would be completed with
ATH9K_TXERR_FILT status only when the corresponding filter bit
for the destination station is already set.

Currently, un-acknowledged  packets are added to the pending queue
and retried, but the "clear_dest_mask" bit in the descriptor is
set only when the TX status has been ATH9K_TXERR_FILT. This results
in packet loss and the log shows:

wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746071
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746076
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746377
...
...

This issue can be resolved by making sure that the destination
mask is cleared when the packet is being retried and the earlier
TX status is ATH9K_TXERR_XRETRY.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-07 15:03:42 -04:00
Mohammed Shafi Shajakhan 4653356f69 ath9k_hw: small optimization
Assign the MCI BT state locally, rather than unnecessarily calling
ar9003_mci_state and updating it.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-07 15:03:39 -04:00
Ming Lei 32e31de5c3 wireless: ath9k-htc: only load firmware in need
It is not necessary to hold the firmware memory during the whole
driver lifetime, and obviously it does waste memory. Suppose there
are 4 ath9k-htc usb dongles working, kernel has to consume about
4*50KBytes RAM to cache firmware for all dongles. After applying the
patch, kernel only caches one single firmware image in RAM for
all ath9k-htc devices just during system suspend/resume cycle.

When system is ready for loading firmware, ath9k-htc can request
the loading from usersapce. During system resume, ath9k-htc still
can load the firmware which was cached in kernel memory before
system suspend.

Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-07 15:03:36 -04:00
Mohammed Shafi Shajakhan 5d9b6f2639 ath9k: Fix a crash in 2 WIRE btcoex chipsets
Generic timers for BTCOEX functionality is applicable
only for 3 WIRE BTCOEX (and MCI) chipsets.
Hence btcoex->no_stomp_timer is allocated only 3 WIRE
btcoex chipsets and in all the other cases its NULL.
Make sure we stop the generic timer only if
'btcoex->hw_timer_enabled' is true(only if its up and
running)

Fixes the following crash

	[68757.020454] BUG: unable to handle kernel NULL pointer dereference at 0000000c
	[68757.020916] IP: [<f9b055c3>] ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
	[68757.021251] *pde = 00000000
	[68757.024384] EIP: 0060:[<f9b055c3>] EFLAGS: 00010082 CPU: 0
	[68757.024384] EIP is at ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
	[68757.024384] EAX: d32d0000 EBX: d32d0000 ECX: 00000000 EDX: 00000000
	[68757.024384] ESI: e67c24c0 EDI: 00000296 EBP: e137be2c ESP: e137be20
	[68757.024384]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
	[68757.024384] CR0: 8005003b CR2: 0000000c CR3: 00b99000 CR4: 000407d0
	[68757.024384] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
	[68757.024384] DR6: ffff0ff0 DR7: 00000400
	[68757.024384] Process kworker/u:2 (pid: 8917, ti=e137a000 task=ea7a6860 task.ti=e137a000)
	[68757.024384] Stack:
	[68757.024384]  c06c4676 d32d0000 e67c24c0 e137be38 f81c9590 e67c1ca0 e137be40 f81c95d9
	[68757.024384]  e137be64 f81cd1c5 00000246 00000002 d32d0000 e67c05e0 e67c1ca0 e67c05e0
	[68757.024384]  00000000 e137beac f81cdfa0 e137be84 00000246 00000246 e67c1ca0 e67c1ca0
	[68757.024384] Call Trace:
	[68757.024384]  [<c06c4676>] ? _raw_spin_lock_irqsave+0x86/0xa0
	[68757.024384]  [<f81c9590>] ath9k_gen_timer_stop+0x10/0x40 [ath9k]
	[68757.024384]  [<f81c95d9>] ath9k_btcoex_stop_gen_timer+0x19/0x20 [ath9k]
	[68757.024384]  [<f81cd1c5>] ath9k_ps_restore+0x85/0x110 [ath9k]
	[68757.024384]  [<f81cdfa0>] ath9k_config+0x220/0x520 [ath9k]
	[68757.024384]  [<f81cd47d>] ? ath9k_flush+0x15d/0x1b0 [ath9k]
	[68757.024384]  [<f85c7ca5>] ieee80211_hw_config+0x135/0x2c0 [mac80211]
	[68757.024384]  [<f860e3c8>] ieee80211_dynamic_ps_enable_work+0x198/0x5f0 [mac80211]

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:33 -04:00
Felix Fietkau b3ccc1a562 ath9k_hw: enable PA linearization
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.

On many newer devices, the calibration is assumed to be done with PA
linearization enabled.

Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:33 -04:00
Felix Fietkau 51dea9be7e ath9k: fix PA linearization calibration related crash
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:32 -04:00
Felix Fietkau 1630d25fd0 ath9k_hw: disable PA linearization for AR9462
Support for it is incomplete

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:32 -04:00
Felix Fietkau 381c726c09 ath9k_hw: calibrate PA input for PA predistortion
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:31 -04:00
Felix Fietkau 2622895993 ath9k_hw: clear the AM2PM predistortion mask on AR933x
That predistortion type is not supported

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:31 -04:00
Felix Fietkau 280b9a9de1 ath9k_hw: do not enable the MIB interrupt in the interrupt mask register
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:30 -04:00
Jiang Liu 08bd108096 ath9k: Use PCI Express Capability accessors
Use PCI Express Capability access functions to simplify ath9k driver.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-23 10:11:14 -06:00
Christian Lamparter 33dd7699ce carl9170: report A-MPDU status
Because the hardware reports whenever an frame
was either at the start, in the middle or at
the end of a A-MPDU, we can easily report the
information for radiotap.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-21 16:06:30 -04:00
Antonio Quartulli 6957802944 ath9k_htc: implement sta_rc_update() mac80211 callback
In case of changes in the supported rates set for a given station, it is now
possible to use this callback to update the current internal state of the
station in the htc driver.

Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-21 16:05:53 -04:00
John W. Linville 01e17dacd4 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
	drivers/net/wireless/mac80211_hwsim.c
2012-08-21 16:00:21 -04:00
Thomas Huehn 3a245cbef6 ath5k: fix wrong max power per rate eeprom reads for 802.11a
This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.

Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-21 14:58:20 -04:00
Bob Copeland 7dd6753f6d ath5k: fix spin_lock_irqsave/spin_lock_bh nesting in mesh
Lockdep found an inconsistent lock state when joining a mesh with
ath5k.  The problem is that ath5k takes the lock for its beacon state,
ah->block, with spin_lock_irqsave(), while mesh internally takes the
sync_offset_lock with spin_lock_bh() in mesh_sync_offset_adjust_tbtt(),
which in turn is called under ah->block.

This could deadlock if the beacon tasklet was run on the processor
that held the beacon lock during the do_softirq() in spin_unlock_bh().

We probably shouldn't hold the lock around the callbacks, but the
easiest fix is to switch to spin_lock_bh for ah->block: it doesn't
need interrupts disabled anyway as the data in question is only accessed
in softirq or process context.

Fixes the following lockdep warning:

[  446.892304] WARNING: at kernel/softirq.c:159 _local_bh_enable_ip+0x38/0xa6()
[  446.892306] Hardware name: MacBook1,1
[  446.892309] Modules linked in: tcp_lp fuse sunrpc cpufreq_ondemand acpi_cpufreq mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4 ip6table_filter nf_defrag_ipv4 xt_state nf_conntrack ip6_tables ext2 arc4 btusb bluetooth snd_hda_codec_idt snd_hda_intel carl9170 snd_hda_codec coretemp joydev ath5k snd_hwdep snd_seq isight_firmware ath snd_seq_device snd_pcm applesmc appletouch mac80211 input_polldev snd_timer microcode cfg80211 snd lpc_ich pcspkr i2c_i801 mfd_core soundcore rfkill snd_page_alloc sky2 tpm_infineon virtio_net kvm_intel kvm i915 drm_kms_helper drm i2c_algo_bit i2c_core video
[  446.892385] Pid: 1892, comm: iw Not tainted 3.6.0-rc1-wl+ #296
[  446.892387] Call Trace:
[  446.892394]  [<c0432958>] warn_slowpath_common+0x7c/0x91
[  446.892398]  [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[  446.892403]  [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[  446.892459]  [<f7f9ae3b>] ? mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  446.892464]  [<c043298f>] warn_slowpath_null+0x22/0x24
[  446.892468]  [<c04399d7>] _local_bh_enable_ip+0x38/0xa6
[  446.892473]  [<c0439a52>] local_bh_enable_ip+0xd/0xf
[  446.892479]  [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[  446.892527]  [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  446.892569]  [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[  446.892575]  [<c047ceeb>] ? trace_hardirqs_on_caller+0x10e/0x13f
[  446.892591]  [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[  446.892597]  [<c047ad67>] ? lock_acquired+0x1f5/0x21e
[  446.892612]  [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[  446.892617]  [<c087f9ea>] ? _raw_spin_lock_irqsave+0x78/0x82
[  446.892632]  [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[  446.892647]  [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[  446.892651]  [<c0479dd4>] ? lock_is_held+0x73/0x7b
[  446.892662]  [<c0458fd5>] ? __might_sleep+0xa7/0x17a
[  446.892698]  [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[  446.892703]  [<c0449875>] ? queue_work+0x24/0x32
[  446.892718]  [<f7fdf894>] ? ath5k_configure_filter+0x163/0x163 [ath5k]
[  446.892766]  [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[  446.892806]  [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[  446.892834]  [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[  446.892855]  [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[  446.892875]  [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[  446.892908]  [<f7a8db99>] ? nl80211_set_wiphy+0x4cf/0x4cf [cfg80211]
[  446.892919]  [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[  446.892940]  [<c07cf861>] ? genl_rcv+0x25/0x25
[  446.892946]  [<c07cf009>] netlink_rcv_skb+0x37/0x78
[  446.892950]  [<c07cf85a>] genl_rcv+0x1e/0x25
[  446.892955]  [<c07cebf3>] netlink_unicast+0xc3/0x12d
[  446.892959]  [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[  446.892966]  [<c079f282>] sock_sendmsg+0x79/0x96
[  446.892972]  [<c04eb90d>] ? might_fault+0x9d/0xa3
[  446.892978]  [<c07a81d8>] ? copy_from_user+0x8/0xa
[  446.892983]  [<c07a852c>] ? verify_iovec+0x43/0x77
[  446.892987]  [<c079f4d8>] __sys_sendmsg+0x180/0x215
[  446.892993]  [<c045f107>] ? sched_clock_cpu+0x134/0x144
[  446.892997]  [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[  446.893002]  [<c047bf88>] ? __lock_acquire+0x46b/0xb6e
[  446.893006]  [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[  446.893010]  [<c045f149>] ? local_clock+0x32/0x49
[  446.893015]  [<c0479ec1>] ? lock_release_holdtime.part.9+0x4b/0x51
[  446.893020]  [<c0479dd4>] ? lock_is_held+0x73/0x7b
[  446.893025]  [<c050d127>] ? fcheck_files+0x97/0xcd
[  446.893029]  [<c050d4df>] ? fget_light+0x2d/0x81
[  446.893034]  [<c07a01f3>] sys_sendmsg+0x3b/0x52
[  446.893038]  [<c07a07b4>] sys_socketcall+0x238/0x2a2
[  446.893044]  [<c0885edf>] sysenter_do_call+0x12/0x38
[  446.893047] ---[ end trace a9af5998f929270f ]---
[  447.627222]
[  447.627232] =================================
[  447.627237] [ INFO: inconsistent lock state ]
[  447.627244] 3.6.0-rc1-wl+ #296 Tainted: G        W
[  447.627248] ---------------------------------
[  447.627253] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  447.627260] swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[  447.627264]  (&(&ah->block)->rlock){+.?...}, at: [<f7fdd2d1>] ath5k_tasklet_beacon+0x91/0xa7 [ath5k]
[  447.627299] {SOFTIRQ-ON-W} state was registered at:
[  447.627304]   [<c047cdbf>] mark_held_locks+0x59/0x77
[  447.627316]   [<c047ceeb>] trace_hardirqs_on_caller+0x10e/0x13f
[  447.627324]   [<c047cf27>] trace_hardirqs_on+0xb/0xd
[  447.627332]   [<c0439a3d>] _local_bh_enable_ip+0x9e/0xa6
[  447.627342]   [<c0439a52>] local_bh_enable_ip+0xd/0xf
[  447.627349]   [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[  447.627359]   [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[  447.627451]   [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[  447.627526]   [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[  447.627547]   [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[  447.627569]   [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[  447.627628]   [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[  447.627712]   [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[  447.627782]   [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[  447.627816]   [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[  447.627845]   [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[  447.627872]   [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[  447.627881]   [<c07cf009>] netlink_rcv_skb+0x37/0x78
[  447.627891]   [<c07cf85a>] genl_rcv+0x1e/0x25
[  447.627898]   [<c07cebf3>] netlink_unicast+0xc3/0x12d
[  447.627907]   [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[  447.627915]   [<c079f282>] sock_sendmsg+0x79/0x96
[  447.627926]   [<c079f4d8>] __sys_sendmsg+0x180/0x215
[  447.627934]   [<c07a01f3>] sys_sendmsg+0x3b/0x52
[  447.627941]   [<c07a07b4>] sys_socketcall+0x238/0x2a2
[  447.627949]   [<c0885edf>] sysenter_do_call+0x12/0x38
[  447.627959] irq event stamp: 1929200
[  447.627963] hardirqs last  enabled at (1929200): [<c043a0e9>] tasklet_hi_action+0x3e/0xbf
[  447.627972] hardirqs last disabled at (1929199): [<c043a0c0>] tasklet_hi_action+0x15/0xbf
[  447.627981] softirqs last  enabled at (1929196): [<c043999d>] _local_bh_enable+0x12/0x14
[  447.627989] softirqs last disabled at (1929197): [<c040443b>] do_softirq+0x63/0xb8
[  447.627999]
[  447.627999] other info that might help us debug this:
[  447.628004]  Possible unsafe locking scenario:
[  447.628004]
[  447.628009]        CPU0
[  447.628012]        ----
[  447.628016]   lock(&(&ah->block)->rlock);
[  447.628023]   <Interrupt>
[  447.628027]     lock(&(&ah->block)->rlock);
[  447.628034]
[  447.628034]  *** DEADLOCK ***

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-13 15:17:25 -04:00
Lorenzo Bianconi e1352fde56 ath9k: fix decrypt_error initialization in ath_rx_tasklet()
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-13 15:17:24 -04:00
Rajkumar Manoharan c771b51819 ath9k: tune rc_stats to display only valid rates
This could make rc_stats more simpler and ease the debugging.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:20 -04:00
Sujith Manoharan 23d9939459 ath9k: Trim rate table
Remove ctrl_rate, cw40index, sgi_index, ht_index and calculate
the rate index for TX status from the valid_rate_index that
is populated at initialization time.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:19 -04:00
Sujith Manoharan f8a87017f4 ath9k: Remove MIMO-PS specific code
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:18 -04:00
Sujith Manoharan 88dcc2dd71 ath9k: Cleanup TX status API
Calculate the final rate index inside ath_rc_tx_status().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:17 -04:00
Sujith Manoharan c1610117f8 ath9k: Bail out properly before calculating rate index
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:16 -04:00
Sujith Manoharan 2e546755b9 ath9k: Fix RTS/CTS rate selection
The current method of assigning the RTS/CTS rate is completely
broken for HT mode and breaks P2P operation. Fix this by using
the basic_rates provided to the driver by mac80211. For now,
choose the lowest supported basic rate for HT frames.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:15 -04:00
Sujith Manoharan 97f7e8a785 ath9k: Do not set IEEE80211_TX_RC_USE_SHORT_PREAMBLE
mac80211 does it for us.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:14 -04:00
Sujith Manoharan 3d2776f621 ath9k: Unify valid rate calculation routines
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:13 -04:00
Sujith Manoharan f5c9a80493 ath9k: Remove ath_rc_set_valid_rate_idx
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:12 -04:00
Sujith Manoharan 6e1e374322 ath9k: Change rateset calculation
Commit "ath9k: Change rate control to use legacy rate as last MRR"
resulted in the mixing of HT/legacy rates in a single rateset,
which is undesirable. Revert this behavior.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:11 -04:00
Sujith Manoharan fc8d023834 ath9k: Cleanup index retrieval routines
Trim API and remove unused variables.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:10 -04:00
Sujith Manoharan dacde35708 ath9k: Cleanup ath_rc_setvalid_htrates
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:09 -04:00
Sujith Manoharan c05ea15177 ath9k: Cleanup ath_rc_setvalid_rates
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:08 -04:00
Sujith Manoharan ea2771f642 ath9k: Cleanup RC init API
A reference to the rate table is stored inside the
private structure, so there is no need to pass "rate_table"
around.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:07 -04:00
Sujith Manoharan 62a291869b ath9k: Simplify rate table initialization
Remove various local variables that duplicate information
already stored in mac80211.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:27:06 -04:00
Nick Kossifidis 987af54fa9 ath5k: Put power_level where it belongs and rename it
Put power_level to ah_txpower struct with the rest tx power infos and
also rename it to txp_requested to make more sense.

v2 make sure we don't memset it to zero on reset

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:26:57 -04:00
Nick Kossifidis 493ca5ef4e ath5k: Preserve tx power level requested from above on phy_init
By using cur_pwr on phy_init we re-use the power level previously set by the
driver, not the one we got from above.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:26:56 -04:00
Nick Kossifidis 755051993b ath5k: Fix range scaling when setting rate power table
rates[i] is unsigned but txp_offset can be negative for newer parts
with PDADC table. We cover the case when rates[i] + txp_offset > 63
but we must also cover the case when its < 0 or else rates[i] will overflow.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:26:55 -04:00
Nick Kossifidis d12c5c53ce ath5k: Use correct value for min_pwr and cur_pwr
Make sure we don't store the table offsets for min and cur power levels,
store the 0.25dB values instead. This way we don't clamp the tx power level
to max (because now cur_pwr holds the 0.25dB value, not the table offset) after
re-using cur_pwr on reset.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 15:26:55 -04:00
Rajkumar Manoharan e19f15ac64 ath9k: stop btcoex on device suspend
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.

Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 14:51:29 -04:00
Felix Fietkau f41a9b3b15 ath9k: fix interrupt storms on queued hardware reset
commit b74713d04e
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.

Fix this by disabling IRQs in the handler without touching intr_ref_cnt.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10 14:50:24 -04:00
Gabor Juhos 2a0b50c770 ath9k: fix indentation in ar9003_hw_set_power_per_rate_table
The current indentation is off by one tab.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06 15:12:44 -04:00
Gabor Juhos 5fc512439f ath9k: optimize power level initialization for CTL_[25]GHT20
The first part of the power array is initialized in a loop
and the last two values are initialized separately. Extend
the loop to cover the last two items, and remove the separate
initialization.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06 15:12:43 -04:00
Javier Lopez da93c26d0b carl9170: Add support for NL80211_IFTYPE_MESH_POINT interfaces
This patch contains following modifications:

- Add mesh capabilities on fw.c to permit creation of mesh
  interfaces using this driver.

- Modify carl9170_set_operating_mode, to use AP-style beaconing
  with mesh interfaces.

- Allow beacon updates for NL80211_IFTYPE_MESH_POINT type in
  carl9170_handle_command_response.

- Add NL80211_IFTYPE_MESH_POINT case on carl9170_op_add_interfaces to
  support mesh/ap/sta virtual interface combinations.

Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06 15:01:56 -04:00
Mohammed Shafi Shajakhan d4e5979c0d ath9k: Add PID/VID support for AR1111
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.

Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-03 10:11:14 -04:00
Thomas Huehn 36323f817a mac80211: move TX station pointer and restructure TX
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.

Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-31 16:18:39 +02:00
John W. Linville 90b90f60c4 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-07-20 12:30:48 -04:00
Rajkumar Manoharan 124b979bae ath9k: Fix race in reset-work usage
Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:40 -04:00
Sujith Manoharan 6dcc344469 ath9k: Reconfigure VIF state properly
When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:40 -04:00
Sujith Manoharan da0d45f7b1 ath9k: Fix ANI management
Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan fb6e252f8d ath9k: Cleanup the beacon tasklet
Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan 2f8e82e8ab ath9k: Set the TSF adjust value properly
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan 7e52c8aa35 ath9k: Cleanup beacon queue configuration
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan aa45fe9683 ath9k: Remove is_bslot_active
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:39 -04:00
Sujith Manoharan ef4ad63368 ath9k: Cleanup beacon logic
* The beaconing status routine is not required, since in
  multi-VIF cases the HW beacon parameters should not be
  re-configured.

* Remove SC_OP_TSF_RESET - when a beaconing interface comes
  up the first time, the TSF has to be reset.

* Simplify ath9k_allow_beacon_config().

* Handle setting/clearing the SWBA interrupt properly.

* Remove the TSF mangling in IBSS mode, it is not required.

* General code cleanup.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 6c43c090a9 ath9k: Simplify ASSOC handling
Cleanup the messy logic dealing with station association
and disassociation.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan df35d29e17 ath9k: Cleanup interface handling
* Do not set/clear TSF when adding/deleting an interface.
  This should be done when the BSS is set up and should also
  take into account the existence of other interfaces.

* Set opmode explicitly.

* ANI setup needs to be decided based on multiple interfaces.
  This can be done via the bss_info_changed() callback.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 60ca9f8744 ath9k_hw: Cleanup ath9k_hw_set_tsfadjust
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:38 -04:00
Sujith Manoharan 130ef6e9dc ath9k: Fix beacon setup
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:37 -04:00
Felix Fietkau 0f245ed20b ath5k: fix txop limit handling
Same as the recent ath9k fix

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:37 -04:00
Felix Fietkau 08a4a1ab07 ath9k_hw: fix SREV checks for applying tuning caps from EEPROM
AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 3e2ea54328 ath9k_hw: apply XLNA bias settings from EEPROM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 0aefc591be ath9k_hw: clean up AR9003 EEPROM code
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
  access the relevant fields directly

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:36 -04:00
Felix Fietkau 89be49e1cd ath9k_hw: apply XPA timing control values from EEPROM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau aa5955c36f ath9k: fix aggregate size limit based on queue TXOP limit
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.

The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.

Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.

Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau 7702e788e7 ath9k: make per-WMM-AC queue sizes configurable via debugfs
Prepare for using different queue size defaults for each AC.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau 531bd07905 ath9k/ath9k_htc: fix txop limit handling
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:35 -04:00
Felix Fietkau a364517b1e ath9k_hw: remove redundant arguments to INIT_INI_ARRAY
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau b05a01110e ath9k_hw: fix tx gain tables for AR934x
Use the EEPROM information to choose the right tx gain table

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 00f97b4fd5 ath9k_hw: enable ANI on AR934x
It has been tested and works properly

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 5d9c7e3c82 ath9k: validate rx antenna settings
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:34 -04:00
Felix Fietkau 01967360a2 ath9k_hw: fall back to OTP ROM when platform data has no valid eeprom data
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:33 -04:00
Felix Fietkau 530275e52b ath9k_hw: fix 5 GHz frequency selection on AR934x/AR955x with 25 MHz refclock
The old code was an accidental copy&paste of the 2.4 GHz version,
which doesn't work.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:32 -04:00
Luis R. Rodriguez 00267d591b ath9k: make CONFIG_ATH9K_DFS_CERTIFIED depend on CFG80211_CERTIFICATION_ONUS
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-17 15:11:31 -04:00
Mohammed Shafi Shajakhan 4a17a50d8d ath9k: do not disable hardware while wow is enabled
Hardware needs to be AWAKE and should maintain association
with the AP to process WoW triggers any time

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:17 -04:00
Mohammed Shafi Shajakhan b11e640aef ath9k: Add WoW related mac80211 callbacks
add suspend/resume/set_wakeup callbacks to the driver

*suspend

- bail out only if all the conditions for configuring WoW.
  is fine, currently multivif case is not handled
- check for associated state.
- map wow triggers from user space data.
- add deauth/disassoc pattern and user defined pattern,
  for the later a list is maintained.
- store the interrupt mask before suspend, enabled beacon
  miss interrupt for WoW.
- configure WoW in the hardware by calling ath9k_hw_wow_enable.

*resume

- restore the interrupts based on the interrupt mask
  stored before suspend.
- call ath9k_hw_wow_wakeup to configure/restore the hardware.
- after wow wakeup clear away WoW events and query the
  WoW wakeup reason from the status register

*set_wakeup

- to call 'device_set_wakeup_enable' from cfg80211/mac80211
  when wow is configured and as per Rafael/Johannnes the
  right way to do so rather in the driver suspend/resume
  call back

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:17 -04:00
Mohammed Shafi Shajakhan b3ba6c529b ath: Add Wake-on-Wireless debug mask
to help the developers and users to debug/know
whats happening with WoW

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 64875c63c9 ath9k_hw: Add hardware code for WoW
add a new file wow.c which takes care of the hardware code
for WoW.

*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
	- tracking wow event mask (to suppress spurious
	  wow events)
	- properly configure suspend/resume WAR registers
	- configure PCIE PM control register
	- configure MAC WoW registers and their timeouts
	- enabling wow configuration like magic packet,
	  user patterns based on users configuration
	- configuring timeouts for KAL, beacon miss,
	  aifs, slot time, backoff
	- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
	- primary task is to find the reason for wakeup
	  from the wow status register
	- configure/restore AR_PCIE_PM_CTRL register
	- clear all WoW events
	- configure/restore suspend/resume WAR registers

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 3b604b6cf8 ath9k_hw: INI changes for WoW for AR9002 chipsets
for AR9002 family of chipsets and for WoW sleep, we reprogram
the SerDes so that the PLL and CHK REQ are both enabled. this
uses more power but in certain cases this is required as otherwise
WoW sleep is unstable and chip may disappear.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 9f11e16edc ath9k: advertise supported WoW flags to upper layer
currently the code supports WoW triggers due to
*magic packet
*user defined patterns
*deauth and disassoc patterns
*disconnect - beacon miss, last beacon received timeout,
no ack for keeep alive frames.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan d687809bd8 ath9k_hw: advertise WoW support for capable chipsets
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:16 -04:00
Mohammed Shafi Shajakhan 8e98138958 ath9k_hw: Add WoW hardware capability flags
have seperate wow capability flags for
*basic wow support
*device capable of matching exact user defined pattern
or de-authentication/disassoc pattern
*device such AR9280 requires first four bytes for
all sort of patterns

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
Mohammed Shafi Shajakhan 01c785338e ath9k: Add definitions and structures to support WoW
*add structures, macros and variables for WoW, so that the driver
can make use of it.
*maintain a list for user enabled patterns and masks
*track pattern slots for the hardware limitation on the
maximum number of patterns that can be stored.
*track interrupts enabled before WoW suspend, so
that can be reconfigured after resume
*have macros to parse user defined wow configurations to
hardware code

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
Mohammed Shafi Shajakhan 900902986c ath9k_hw: Add register definitions for WoW support
*MAC WoW registers

back-off shift, MAC interrupt enable, magic packet enable,
pattern match enable, aifs, slot wait period, keep alive
frame failure count, beacon fail enable, beacon timeout,
keep alive timeout, auto keep alive disable,
keep alive fail disable and their corresponding
status registers. keep alive frame delay,
pattern end/byte offsets, transmit buffers for
keep alive frames and storing the user patterns

*Power Management Control registers

pme_d3cold_vaux, host_pme_enable, aux_pwr_detect,
power_state_mask, wow_pme_clear

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 15:27:15 -04:00
John W. Linville d07d152892 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
	drivers/net/wireless/iwmc3200wifi/cfg80211.c
	drivers/net/wireless/mwifiex/cfg80211.c
2012-07-12 15:21:05 -04:00
John W. Linville 38a0084063 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-07-12 13:44:50 -04:00
Johannes Berg fd0142844e nl80211: move scan API to wdev
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:41 +02:00
Johannes Berg 84efbb84cf cfg80211: use wireless_dev for interface management
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:08:10 +02:00
Luis R. Rodriguez 2f8684ce7a ath5k: replace modparam_all_channels with CONFIG_ATH5K_TEST_CHANNELS
This stashes away this feature from standard kernel builds.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:40:23 -04:00
Christian Lamparter c9122c0d63 carl9170: fix HT peer BA session corruption
This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.

Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:

 - "stuck" ba sessions and package loss, as the
   stale BAR would reset the sequence each time.

 - lots of reorder releases.

 - ...

Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Reported-by: Mikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: Per-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:38:26 -04:00
Christian Lamparter 4519a74338 carl9170: import 1.9.6 firmware headers
Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:38:26 -04:00
Rajkumar Manoharan d081257c78 ath9k_hw: remove debugging masks from AR_MCI_INTERRUPT_RX_MSG_DEFAULT
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10 12:16:58 -04:00
Mohammed Shafi Shajakhan c32cdbd84f ath9k: Stop the BTCOEX timers before disabling BTCOEX
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:38 -04:00
Mohammed Shafi Shajakhan dd89f05a75 ath9k: Fix MCI cleanup
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now  as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.

Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:37 -04:00
Gabor Juhos 2b943a3315 ath9k: enable support for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:34 -04:00
Gabor Juhos b3d7aa432a ath9k: set 4ADDRESS bit in RX filter for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:34 -04:00
Gabor Juhos c12b60214c ath9k: enable PLL workaround for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:33 -04:00
Gabor Juhos fc05a31784 ath9k: fix PLL initialization for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:32 -04:00
Gabor Juhos 2e2c9cc37e ath9k: skip internal regulator configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:32 -04:00
Gabor Juhos 3b8a0577b7 ath9k: disable SYNC_HOST1_FATAL interrupts for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:31 -04:00
Gabor Juhos db4a3de9db ath9k: fix RF channel frequency configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:30 -04:00
Gabor Juhos 1ed0f8db5b ath9k: fix PAPRD settings for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:30 -04:00
Gabor Juhos 2d00de48ff ath9k: fix antenna control configuration for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:29 -04:00
Gabor Juhos 4b091727ba ath9k: fix XPABIASLEVEL settings for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:28 -04:00
Gabor Juhos 8528f12ed7 ath9k: read spur frequency information from eeprom for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:28 -04:00
Gabor Juhos 8bc45c6bf2 ath9k: add mode register initialization code for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:27 -04:00
Gabor Juhos a0fbb9bd25 ath9k: add initvals for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:26 -04:00
Gabor Juhos 2f8d10fd86 ath9k: enable TX/RX data byte swap for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:26 -04:00
Gabor Juhos c95b584b8d ath9k: clear pciexpress flag for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:25 -04:00
Gabor Juhos 485124cbb7 ath9k: add BB name string for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:25 -04:00
Gabor Juhos 9476f4d636 ath9k: add platform_device_id for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:24 -04:00
Gabor Juhos 813831dc67 ath9k: set MAC version for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:23 -04:00
Gabor Juhos a4e26081cb ath9k: define MAC version for AR9550
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:23 -04:00
Gabor Juhos b123377935 ath9k: define DEVID for QCA955x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:22 -04:00
Rajkumar Manoharan 83bfea4219 ath9k_hw: fix AR9462 2g5g switch on full reset
On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:20 -04:00
Rajkumar Manoharan 08d4df410a ath9k: fix power consumption on network sleep when BTCOEX is enabled
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:20 -04:00
Rajkumar Manoharan b73f3e7804 ath9k: fix fullsleep power consumption when BTCOEX is enabled
As soon as the interface brought up, btcoex timer starts running
eventhough the interface is in idle state and WLAN chip is moved
to full sleep mode. There is no point in running btcoex timer when
the wlan interface is in sleep mode and also it might consumes
more power on WLAN idle unassociated state. So lets stop the
btcoex when wlan is idle state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:19 -04:00
Rajkumar Manoharan 54717e5330 ath9k_hw: do not load noise floor readings when it is running
Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:18 -04:00
Rajkumar Manoharan 1fe860edb0 ath9k_hw: start noisefloor calibration after MCI reset
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:18 -04:00
Thomas Huehn 1960195725 ath9k: fixing register bit shift values of control packets to support TPC
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.

Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:02 -04:00
Mohammed Shafi Shajakhan c11216d1f6 ath9k: Fix clearing of BTCOEX flags
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.

Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:01 -04:00
John W. Linville 0af5491c2f Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next 2012-07-09 16:34:39 -04:00
John W. Linville 635d999fd3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	net/mac80211/mlme.c
2012-07-09 16:34:34 -04:00
Johannes Berg 71bbc99438 cfg80211: use wdev in mgmt-tx/ROC APIs
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:51:47 +02:00
Thomas Huehn e3e1a0bcb3 mac80211: reduce IEEE80211_TX_MAX_RATES
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.

The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.

Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-03 13:48:37 +02:00
John W. Linville 8732baafc3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
	drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
2012-06-29 12:42:14 -04:00
John W. Linville 42fb0b0278 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-06-29 12:07:37 -04:00
David S. Miller b26d344c6b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/caif/caif_hsi.c
	drivers/net/usb/qmi_wwan.c

The qmi_wwan merge was trivial.

The caif_hsi.c, on the other hand, was not.  It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.

I did my best with that one and will ask Sjur to check it out.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28 17:37:00 -07:00
Felix Fietkau 469979173e ath9k: de-duplicate initvals
The initvals tool from https://github.com/mcgrof/qca-swiss-army-knife has
been modified to detect identical initval tables and replace them with
macros. This patch contains the generated changes.

On MIPS this reduces the binary size by 24 KB with no runtime changes.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:47 -04:00
Felix Fietkau 589ebd8526 ath9k: update AR934x initvals to latest version
Generated using the initvals tool from the qca-swiss-army-knife repository
from https://github.com/mcgrof/qca-swiss-army-knife

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:47 -04:00
Mohammed Shafi Shajakhan d8fffb4a9e ath9k: Fix signedness in a MCI debug message
seems i got a message like this
ath: phy0: BT_Status_Update: is_link=0, linkId=2,
state=1, SEQ=-2085766476 initially.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Mohammed Shafi Shajakhan 812944891c ath9k_hw: make use of the wrapper to check for MCI init
ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Felix Fietkau 73dc3eb8b9 ath9k: fix ANI operation in AP mode
ath9k_ani_reset (which is called at reset time) uses a state variable
ani->update_ani to prevent the ANI noise immunity state on the operating
channel from being overwritten by background scans. Unfortunately this
is also being set for AP mode, since it's mixed with code that is only
supposed to change the default settings after a reset.

In AP mode this has the side effect of having ANI run, but being unable to
change its runtime noise immunity level, making it effectively useless.

Fix this by getting rid of ani->update_ani and passing a parameter to
ath9k_hw_set_ofdm_nil and ath9k_hw_set_cck_nil instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Johannes Berg b1fbd46976 Merge remote-tracking branch 'wireless-next/master' into mac80211-next 2012-06-28 13:45:58 +02:00
Sujith Manoharan bf52592fe4 ath9k: Fix compilation breakage
Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.

Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 15:23:19 -04:00
Tom Hughes 6bb51c70ca ath9k: fix panic caused by returning a descriptor we have queued for reuse
Commit 3a2923e83c introduced a bug when a corrupt descriptor
is encountered - although the following descriptor is discarded
and returned to the queue for reuse the associated frame is
also returned for processing. This leads to a panic:

BUG: unable to handle kernel NULL pointer dereference at 000000000000003a
IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k]
Call Trace:
<IRQ>
[<ffffffff812d7fa0>] ? map_single+0x60/0x60
[<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k]
[<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k]
[<ffffffff8105e133>] tasklet_action+0x63/0xd0
[<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0
[<ffffffff8101a873>] ? native_sched_clock+0x13/0x80
[<ffffffff815f9d5c>] call_softirq+0x1c/0x30
[<ffffffff810151f5>] do_softirq+0x75/0xb0
[<ffffffff8105df95>] irq_exit+0xb5/0xc0
[<ffffffff815fa5b3>] do_IRQ+0x63/0xe0
[<ffffffff815f0cea>] common_interrupt+0x6a/0x6a
<EOI>
[<ffffffff8131840a>] ? intel_idle+0xea/0x150
[<ffffffff813183eb>] ? intel_idle+0xcb/0x150
[<ffffffff814a1db9>] cpuidle_enter+0x19/0x20
[<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240
[<ffffffff8101c4bf>] cpu_idle+0xaf/0x120
[<ffffffff815cda8e>] rest_init+0x72/0x74
[<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4
[<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e
[<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135
[<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f

Making sure bf is cleared to NULL in this case restores the
old behaviour.

Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 14:48:13 -04:00
Panayiotis Karabassis 7508b65796 ath9k: enable serialize_regmode for non-PCIE AR9287
https://bugzilla.kernel.org/show_bug.cgi?id=42903

Based on the work of <fynivx@gmail.com>

Signed-off-by: Panayiotis Karabassis <panayk@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-27 14:48:12 -04:00
Johannes Berg dfb89c56ad cfg80211: don't allow WoWLAN support without CONFIG_PM
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.

Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-27 17:55:11 +02:00
Sujith Manoharan 6bcfe67f98 ath9k_htc: Fix IDLE power save
Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:52 -04:00
Sujith Manoharan d8a2c51cdc ath9k_htc: Use atomic operations for op_flags
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sujith Manoharan fb1c078edb ath9k_htc: Change default listen interval to 1
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sujith Manoharan fad29cd2f5 ath9k: Fix lockdep splat
Cancel the MCI work only when MCI is actually enabled.
Fixes this:

[96833.124051] Call Trace:
[96833.124060]  [<ffffffff810afaf8>] __lock_acquire+0x1518/0x1e40
[96833.124065]  [<ffffffff810ad126>] ? mark_held_locks+0x86/0x110
[96833.124069]  [<ffffffff810ad3ad>] ? trace_hardirqs_on+0xd/0x10
[96833.124073]  [<ffffffff814464f0>] ? _raw_spin_unlock_irq+0x30/0x70
[96833.124078]  [<ffffffff81072968>] ? wait_on_cpu_work+0x98/0xc0
[96833.124082]  [<ffffffff810b0a11>] lock_acquire+0xa1/0x150
[96833.124085]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124088]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124092]  [<ffffffff810729e2>] wait_on_work+0x52/0x120
[96833.124095]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124099]  [<ffffffff81063b3f>] ? del_timer+0x7f/0x110
[96833.124102]  [<ffffffff81072c13>] __cancel_work_timer+0x83/0x130
[96833.124106]  [<ffffffff81072cf0>] cancel_work_sync+0x10/0x20
[96833.124113]  [<ffffffffa065b5cd>] __ath_cancel_work+0x4d/0x60 [ath9k]
[96833.124119]  [<ffffffffa065cf28>] ath9k_config+0x458/0x680 [ath9k]
[96833.124125]  [<ffffffffa065dd1e>] ? ath9k_flush+0x6e/0x1d0 [ath9k]
[96833.124129]  [<ffffffff8144394d>] ? __mutex_unlock_slowpath+0x10d/0x190
[96833.124146]  [<ffffffffa056c7b5>] ieee80211_hw_config+0x135/0x2a0 [mac80211]
[96833.124163]  [<ffffffffa057ebbb>] ieee80211_do_open+0x67b/0xc50 [mac80211]
[96833.124178]  [<ffffffffa057f1fd>] ieee80211_open+0x6d/0x80 [mac80211]
[96833.124183]  [<ffffffff8137a44f>] __dev_open+0x9f/0xf0
[96833.124187]  [<ffffffff8137a701>] __dev_change_flags+0xa1/0x180
[96833.124190]  [<ffffffff8137a898>] dev_change_flags+0x28/0x70
[96833.124195]  [<ffffffff813e1179>] devinet_ioctl+0x659/0x780
[96833.124199]  [<ffffffff8137aea0>] ? dev_ioctl+0x210/0x6d0
[96833.124203]  [<ffffffff813e1db5>] inet_ioctl+0x75/0x90
[96833.124208]  [<ffffffff8135e0e0>] sock_do_ioctl+0x30/0x70
[96833.124211]  [<ffffffff8135e3dd>] sock_ioctl+0x7d/0x2c0
[96833.124218]  [<ffffffff81193c39>] do_vfs_ioctl+0x99/0x580
[96833.124222]  [<ffffffff81447415>] ? sysret_check+0x22/0x5d
[96833.124226]  [<ffffffff811941b9>] sys_ioctl+0x99/0xa0
[96833.124230]  [<ffffffff814473e9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:51 -04:00
Sven Eckelmann 313eb87f1e ath9k: raise aggregation limit to 64k for HT IBSS
mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.

This patch changes this to update ampdu factor/density settings
when starting a blockack session.

Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-26 14:28:50 -04:00
David S. Miller e486463e82 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/usb/qmi_wwan.c
	net/batman-adv/translation-table.c
	net/ipv6/route.c

qmi_wwan.c resolution provided by Bjørn Mork.

batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.

ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-25 15:50:32 -07:00
Felix Fietkau bed3d9c0b7 ath9k: fix dynamic WEP related regression
commit 7a532fe713
ath9k_hw: fix interpretation of the rx KeyMiss flag

This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.

This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.

Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-25 15:14:13 -04:00
Rajkumar Manoharan 4b5237cc86 ath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck
drivers/net/wireless/ath/ath9k/ar9003_phy.c:211
ar9003_hw_spur_mitigate_mrc_cck() error: potential NULL dereference
'spur_fbin_ptr'.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-22 14:44:06 -04:00
Rajkumar Manoharan 81b67fd60a ath9k_hw: rename mrcCCKOff to fix smatch warning
Rename mrcCCKOff for better code readability and also fixes
the smatch warning.

drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
	ar9003_hw_ani_control() Error invalid range 1 to 0.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-22 14:44:05 -04:00
Rajkumar Manoharan 5039f38e16 ath9k: do not sampling on ani timer when chip is in sleep
The baseband and cycle counters are being sampled during ani
processing for debugging purpose. Whenever the ani is postponded
due to sleep state, taking samples on that time is of no use and
also unneccesarily waking up the chip might increase the power
consumption on idle associated state. Hence moving debug function
within powersave block.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:56 -04:00
Rajkumar Manoharan 4ff6a9d200 ath9k_hw: fix LNA control on WLAN sleep
When WLAN enter full sleep mode, WLAN HW should send out a LNA_TAKE
message for BT to take control of the shared LNA. Otherwise BT traffic
is completely stopped whenever the wlan interface is moved full sleep
mode.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:54 -04:00
Rajkumar Manoharan 0967d86231 ath9k_hw: update ar9462 dac_async_fifo initval
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:52 -04:00
Rajkumar Manoharan e1ecad78e5 ath9k: fix mci_is_enabled utility
During driver stop, btcoex is disabled and also btcoex_hw.enabled
is set to false. Afterwards mci_is_enabled returns false so that
BT is not gaining SPDT control on WLAN sleep. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-20 15:14:51 -04:00