This reduced the power consumption to half in full and network sleep.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.
The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170_handle_mpdu is the final part of the
rx path of the driver. It splits the raw data
streams from the device into skb packets and
passes them on to mac80211. As a result of
continuous updates, it grew over the years when
new code was added by the following commits:
- report A-MPDU status
- fix HT peer BA session corruption
- A-MPDU frame type filter
- ...
This patch splits the routine into two stages.
The first stage only deals with the details
about extracting and verifying the data from
the incoming stream. Whereas the second stage
packs it into skbs and passes it on to mac80211.
Reported-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several people have complained about an unusual
and undocumented feature of the AR9170 hardware:
In siffer mode, the hardware generates spurious
ACK frames for every received frame... even
broadcasts.
The reason for this malfunction is unknown:
<http://marc.info/?l=linux-wireless&m=134517238506033>
But there's a workaround: Instead of the special
sniffer mode, the hardware will be put into
station mode and all rx filters are disabled.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marco Fonseca <marco@tampabay.rr.com>
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now the ANI cycle is executed only when the chip is awake.
On idle state case, the station wakes up from network sleep for
beacon reception. Since most of the time, ANI cycle is not syncing
with beacon wakeup, ANI cycle is ignored. Approx 5 mins once, the
calibration is performed. This could affect the connection stability
when the station is idle for long. Even though the OFDM and CCK phy
error rates are too high, ANI is unable to tune its immunity level
as quick enough due to rare execution.
Here the experiment shows that OFDM and CCK levels are at default
even on higher phy error rate.
listenTime=44 OFDM:3 errs=121977/s CCK:2 errs=440818/s ofdm_turn=1
This change ensures that ANI calibration will be exectued atleast
once for every 10 seconds. The below result shows improvements and
immunity levels are adopted quick enough.
listenTime=557 OFDM:4 errs=752/s CCK:4 errs=125/s ofdm_turn=0
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the way the driver deals with
command responses and traps which are sent through
the special interrupt input endpoint 3.
While the carl9170 firmware does not use this
endpoint for command responses or traps, the
firmware loader on the device does. It uses it
to notify the host about 'watchdog triggered'
in case the firmware/hardware has crashed.
Note:
Even without this patch, the driver is still
able to detect the mishap and reset the device.
But previously it did that because the trap
event caused an out-of-order message sequence
number error, which also triggered a reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All defines for REG_WRITE in Atheros wireless drivers use the order "ah",
"register" and "value". hw.c is the only file using the order "ah", "value" and
"register".
drivers/net/wireless/ath/ath9k/hw.h:#define REG_WRITE(_ah, _reg, _val) \
drivers/net/wireless/ath/key.c:#define REG_WRITE(_ah, _reg, _val) (common->ops->write)(_ah, _val, _reg)
This inconsistent definition can easily lead to implementation errors. The
modification doesn't change the behavior of the driver or the generated code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch remove a semicolon after if(...) that is preventing the
error check to work correctly. Removing this semicolon will change the
code behavior, but this is intended.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
position p;
@@
if (...);@p
@script:python@
p0 << r1.p;
@@
// Emacs org-mode output
cocci.print_main("", p0)
cocci.print_secs("", p0)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips
and using it for MCI-based cards is incorrect. Fix this by
cleaning up its usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the following bug:
usb 1-1.1: restart device (8)
BUG: sleeping function called from invalid context at drivers/usb/core/urb.c:654
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
(usb_poison_urb+0x1c/0xf8)
(usb_poison_anchored_urbs+0x48/0x78)
(carl9170_usb_handle_tx_err+0x128/0x150)
(carl9170_usb_reset+0xc/0x20)
(carl9170_handle_command_response+0x298/0xea8)
(carl9170_usb_tasklet+0x68/0x184)
(tasklet_hi_action+0x84/0xdc)
this only happens if the device is plugged in an USB port,
the driver is loaded but inactive (e.g. the wlan interface
is down). If the device is active everything is fine.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dereference should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using ieee80211_free_txskb for tx frames is required, since mac80211 clones
skbs for which socket tx status is requested.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that drv_start() always returns true, as a failing hw start usually
eventually leads to crashes when there's still a station entry present.
Call a power-on reset after a resume and after a hw reset failure to bring
the hardware back to life again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_pci_aspm_init is only called on card init, so PCI registers get reset
after a suspend/resume cycle.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
John W. Linville says:
====================
Here is another batch of updates intended for 3.7...
Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
The WLAN/BT weights have to set correctly before BTCOEX
is initialized. Currently, this is not done for all chips
in the AR9003 family. This patch fixes this issue by setting
the weights in the init path. While at it, rename ar9462_wlan_weights
to mci_wlan_weights since it is common to both AR9462 and AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupts with the sync_cause AR_INTR_SYNC_HOST1_FATAL and
AR_INTR_SYNC_HOST1_PERR have to be handled using a chip reset. Otherwise a
interrupt storm with unhandled interrupts will cause a hang or crash of the
machine.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force chain 1 to be used for CCK rates since the target power
table stored in EEPROM is too high to transmit with both chains.
This is needed to avoid regulatory violation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCI initialization path has various points of failures,
handle these to ensure that we bail out correctly in such
cases.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to have the promiscuous mode enabled for older
chipsets so that the olderchips hardware does not
filters out some valid/necessary frames that need
to be sent to mac80211. Fix this by enabling promiscus
mode for all the chipsets whose macversion <= AR9160
chipsets. This should fix
https://bugzilla.kernel.org/show_bug.cgi?id=45591
shafi: made the fix generic by having the frame filtering
disabled for chipsets older than AR9280.
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Wagner <Thomas.Wagner@hs-rm.de>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever both WLAN and BT in/out sleep mode, sometimes WLAN
is not able to take back the shared LNA control after resumes
from sleep mode. The idea is that for WLAN to check if BT owns
LNA control and BT is in sleep mode when WLAN just resumes from
sleep mode. If the condition is true, do a BTCOEX_RC_WARM_RESET
for WLAN to take back the control of shared LNA.
Now the issue is the BT sleep value read from MCI register is
overlooked by assigning u32 into u8. Hence the above condition never
be met so that WLAN used to report beacon losses and frequent
connection drops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Tested-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>