This will place the joystick's input device into propoer place in sysfs
hierarchy as long as th port has device assigned to it (i.e. it is not
legacy port).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On resume from suspend there is a possibility for multi-byte scancodes
to be handled incorrectly. atkbd_reconnect disables the processing of
scancodes in software by calling atkbd_disable, but the keyboard may
still be active because no disconnect command was sent. Later, software
handling is re-enabled. If a multi-byte scancode sent from the keyboard
straddles the re-enable, only the latter byte(s) will be handled.
In practice, this leads to cases where multi-byte break codes (ex. "e0
4d" - break code for right-arrow) are misread as make codes ("4d" - make
code for numeric 6), leading to one or more unwanted, untyped characters
being interpreted.
The solution implemented here involves sending command f5 (reset
disable) to the keyboard prior to disabling software handling of codes.
Later, the command to re-enable the keyboard is sent only after we are
prepared to handle scancodes.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is time to switch to system wq instead creating a queue for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This simplifies error handling and eliminates the need for implementing
remove() method.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a driver for Cypress All Points Addressable
I2C Trackpad, including the ones in 2012 Samsung Chromebooks.
This device is compatible with MT protocol type B, providing identifiable
contacts.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_* APIs are device managed and make the exit and clean up code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan<ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tegra KBC driver have the default key mapping for 16x8 configuration.
The key mapping can be provided through platform data or through DT
and the mapping varies from platform to platform, hence this default
mapping is not so useful. Remove the default mapping to reduce the code
lines of the driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.
Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_* for memory, clock, irq, input device allocation. This reduces
code for freeing these resources.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the following build warning when building driver with CONFIG_PM_SLEEP
not selected.
tegra-kbc.c:360:13: warning: 'tegra_kbc_set_keypress_interrupt' defined but not used [-Wunused-function]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver, submitted on behalf of Cypress Semiconductor Corporation and
additional contributors, provides support for the Cypress PS/2 Trackpad.
Original code contributed by Dudley Du (Cypress Semiconductor Corporation),
modified by Kamal Mostafa and Kyle Fazzari.
BugLink: http://launchpad.net/bugs/978807
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Kyle Fazzari <git@status.e4ward.com>
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Herton Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently some users of managed input devices are confused whether
input_unregister_device() is needed when working with them. Clarify
this in the kernel doc for devm_input_allocate_device(): in most cases
there is no need to call neither input_unregister_device() nor
input_free_device() when working with managed devices.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch brings wacom driver in-sync with input-mt changes
made in release 3.7.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Henrik added new MT routines in release 3.7. This patch is to prepare
for the use of new MT routines.
In the newly added wacom_abs_set_axis() function, the first
if-statement assigns ABS_X/Y for number of contacts less or equal
to 2. So, it is single and 2 finger touch devices. Two finger touch
devices are processed here since they will not use the updated
input_mt_init_slots(), which does not offer benefit to those devices.
input_mt_init_slots() will take care of ABS_X/Y assignment when flags
are not zero. All touch devices with more than two contacts will use
input_mt_init_slots() with non-zero flags.
The second if-statement is for all MT devices, which include two
finger touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
INT_PWM1 is already a bitmask, not the bit number, so shifting by INT_PWM1 is
incorrect.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Outputs x8..x0 of the qt2160 can have leds attached to it.
This patch handles those outputs using the generic LED
framework.
The PWM controls available in the chip are used to achieve
different levels of brightness.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input update from Dmitry Torokhov:
"Updates for the input subsystem. Just a couple of driver fixes this
time."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_keys - defer probing if GPIO probing is deferred
Input: gpio_keys_polled - defer probing if GPIO probing is deferred
Input: sentelic - only report position of first finger as ST coordinates
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds device tree support for imx keypad driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Only use the defines which are defined in the platform_data include
file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The datasheet doesn't say anything about writing twice, so this was
probably overlooked.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Don't open code the AC_READ and AC_WRITE macros.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If of_get_gpio_flags() returns an error (as in case when GPIO probe is
deferred) the driver would attempt to claim invalid GPIO. It should
propagate the error code up the stack instead so that the probe either
fails or will be retried later (in case of -EPROBE_DEFER).
Cc: stable@vger.kernel.org
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If GPIO probing is deferred, the driver tries to claim an invalid GPIO line
which leads to an error message like this:
gpio-keys-polled buttons.2: unable to claim gpio 4294966779, err=-22
gpio-keys-polled: probe of buttons.2 failed with error -22
We should make sure that error code returned by of_get_gpio_flags (including
-EPROBE_DEFER) is propagated up the stack.
Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Report only the position of the first finger as absolute non-MT coordinates,
instead of reporting both fingers alternatively. Actual MT events are
unaffected.
This fixes horizontal and improves vertical scrolling with the touchpad.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe TORDEUX <christophe@tordeux.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull small x86 fixes from Peter Anvin:
"A collection of very small fixes, mostly pure documentation."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, doc: Document that bootloader ID 4 is used also by iPXE
x86, doc: Add a formal bootloader ID for kexec-tools
x86, 8042: Enable A20 using KBC to fix S3 resume on some MSI laptops
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
The driver's timer must be set up before enabling IRQ handler, otherwise
bad things may happen.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Popovec <popovec@fei.tuke.sk>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID subsystem updates from Jiri Kosina:
1) Support for HID over I2C bus has been added by Benjamin Tissoires.
ACPI device discovery is still in the works.
2) Support for Win8 Multitiouch protocol is being added, most work done
by Benjamin Tissoires as well
3) EIO/ERESTARTSYS is fixed in hiddev/hidraw, fixes by Andrew Duggan
and Jiri Kosina
4) ION iCade driver added by Bastien Nocera
5) Support for a couple new Roccat devices has been added by Stefan
Achatz
6) HID sensor hubs are now auto-detected instead of having to list all
the VID/PID combinations in the blacklist array
7) other random fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (65 commits)
HID: i2c-hid: add mutex protecting open/close race
Revert "HID: sensors: add to special driver list"
HID: sensors: autodetect USB HID sensor hubs
HID: hidp: fallback to input session properly if hid is blacklisted
HID: i2c-hid: fix ret_count check
HID: i2c-hid: fix i2c_hid_get_raw_report count mismatches
HID: i2c-hid: remove extra .irq field in struct i2c_hid
HID: i2c-hid: reorder allocation/free of buffers
HID: i2c-hid: fix memory corruption due to missing hid declaration
HID: i2c-hid: remove superfluous include
HID: i2c-hid: remove unneeded test in i2c_hid_remove
HID: i2c-hid: i2c_hid_get_report may fail
HID: i2c-hid: also call i2c_hid_free_buffers in i2c_hid_remove
HID: i2c-hid: fix error messages
HID: i2c-hid: fix return paths
HID: i2c-hid: remove unused static declarations
HID: i2c-hid: fix i2c_hid_dbg macro
HID: i2c-hid: fix checkpatch.pl warning
HID: i2c-hid: enhance Kconfig
HID: i2c-hid: change I2C name
...
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is
not quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq. note
that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UJlh
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
Some MSI laptop BIOSes are broken - INT 15h code uses port 92h to enable A20
line but resume code assumes that KBC was used.
The laptop will not resume from S3 otherwise but powers off after a while
and then powers on again stuck with a blank screen.
Fix it by enabling A20 using KBC in i8042_platform_init for x86.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=12878
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/201212112218.06551.linux@rainbow-software.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The matrix-keymap module is currently lacking a proper module license,
add one so we don't have this module tainting the entire kernel. This
issue has been present since commit 1932811f42 ("Input: matrix-keymap
- uninline and prepare for device tree support")
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@vger.kernel.org # v3.5+
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The matrix-keymap module is currently lacking a proper module license,
add one so we don't have this module tainting the entire kernel. This
issue has been present since commit 1932811f (Input: matrix-keymap -
uninline and prepare for device tree support)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f393ee2b81 forgot to add the
touch_max property for Wacom Bamboo Fun CTH-461/S, ID 056a:00d2.
This broke the touch functionality for that device. This patch,
(done with help of Ping Cheng), adds the correct value and makes
touch work again.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds VID/PID combinations for MadCatz, PDP and PowerA (new).
Removed Pelican 'TSZ' Wired Xbox 360 Controller since it's clashing with Edge
wireless Controller and I failed to confirm the PID.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixed a few minor coding style issues in xpad driver.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using devm_*() interfaces to manage our resources,
thus will simplify error unwinding a bit.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Failures to build a keymap, request an IRQ, or register input device are
fatal for the driver, therefore the messages should have "error" severity
instead of "debug".
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This matches structure of most other input drivers.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to use proper accessor functions instead of directly poking into
various structures.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use a temporary variable for our parent device (coming from I2C client
structure); we'll be also using it during conversion to managed resources.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.
Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The kernel does not contain the symbol SA1100_BITSY so the driver
is never compiled and can be removed safely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now we can register the BU21013_ts touch screen when booting with Device
Tree enabled. Here we parse all the necessary components previously
expected to be passed from platform data.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These GPIO init and exit functions have no place in platform data, they
should be part of the driver instead,
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the BU21013 Touch Screen driver requests a regulator by the
name of 'V-TOUCH', which doesn't exist anywhere in the kernel. The
correct name, as referenced in platform regulator code is 'avdd'. Here,
when we request a regulator, we use the correct name instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Disable hardware if active when suspending if the hw can not
wake the system from suspend.
[Dmitry Torokhov: use input_dev->users instead of a separate flag]
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Reviewed-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of reporting the initial stage when the device is registered we
should do it when the device is opened (so there are users).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_* functions are device managed and make error handling and code
simpler. While at it also fix error exit paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_{un}prepare is mandatory for platforms using common clock framework.
Because for SPEAr we don't do anything in clk_{un}prepare() calls, just
call them once in probe/remove.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In imx_keypad_inhibit(), all 8 columns were set to open-drain, in
contrast to the rest of the driver, where only the enabled columns
are modified/used.
Contrary to the normal expectation, this also affects column I/Os not
even mapped via IOMUX to the KPP hardware module but used as a GPIO.
Therefore only init enabled columns to open-drain and leave all others
with their default reset value of 0, i.e. totem-pole.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to call tasklet_disable() before calling tasklet_kill() if
taskelt does not reschedult itself.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To facilitate upcoming cleanup in twl stack switch from using
TWL4030_MODULE_PM_MASTER define to usingTWL_MODULE_PM_MASTER.
There are no functional changes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
The updated type enum enables this implementation.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Also the driver was modifued to take advantage of recent improvements in
matrix_keypad_build_keymap() implementation, which automatically allocates
memory for keymap.
The driver was tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new da9052 irq functions and allow the driver to probe successfully.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently da9062_tsi does not probe and it fails as follows:
da9052 1-0048: Unable to determine device interrupts
Use the new da9052 irq functions and allow the driver to probe and operate
correctly.
Tested on mx53qsb board using 'evtest' tool.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When doing conversion to dynamic input numbers I inadvertently moved
/dev/input/mice from c,13,63 to c,13,31. We need to fix this so that
setups with statically populated /dev continue working.
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch extracts the test (slot->frame == mt->frame) so that it can
be used in third party drivers.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In device tree enabled setups requiring preallocated memory for storing keymap
is quite often awkward, so let's provide an option of allocating it directly
in matrix_keypad_build_keymap().
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This goto is only used to skip the next instruction, which can easily be done
without a goto.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes new kernel-doc warning in input-mt.c:
Warning(drivers/input/input-mt.c:38): No description found for parameter
'flags'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees stmpe-ts driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees stmpe-keyboard driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees spear-keyboard driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch handles the fix for unbalanced irq for the cases when
enable_irq_wake fails, and a warning related to same is displayed
on the console. The workaround is handled at the driver level.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously this clock was handled internally by the clockdriver,
but now this is separate clk. So we need take care of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do proper error handling for clk and make sure clocks are being
prepared|unprepared as well as enabled|disabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the two new multi-touch tablets.
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use switch instead of if statement to verify device types
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov