Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
There will be a merge conflict in drivers/power/supply/ab8500_chargalg.c
with your tree, the merge conflict should be easy (take all the
changes).
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG6PA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylMFwCfSIyAU4oLEgj+/Rfmx4o45cAVIWMAnit3zbdU
wUUCGqKcOnTJEcW6dMPh
=1VVi
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc. small improvements and fixes
-----BEGIN PGP SIGNATURE-----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=OiYc
-----END PGP SIGNATURE-----
Merge tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
The HRTimer in the AB8500 charging code is using CLOCK_REALTIME
to set an alarm some hours forward in time +/- 5 min for a safety
timer.
I have observed that this will sometimes fire sporadically
early when charging a battery with the result that
charging stops.
As CLOCK_REALTIME can be subject to adjustments of time from
sources such as NTP, this cannot be trusted and will likely
for example fire events if the clock is set forward some hours
by say NTP.
Use CLOCK_MONOTONIC as indicated in other instances and the
problem goes away. Also initialize the timer to REL mode
as this is what will be used later.
Fixes: 257107ae6b ("ab8500-chargalg: Use hrtimer")
Cc: Lee Jones <lee.jones@linaro.org>
Suggested-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver supports several chip variants which all share the same I2C
register interface. Since the chip will turn off and become inaccessible
under conditions outside of software control (e.g. upon button press or
input voltage removal), some special handling is needed to delay the
initialization of the IC until it is accessible.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Kernel test robot reported below warning ->
drivers/power/supply/ab8500_chargalg.c:790:13: warning:
variable 'delta_i_ua' set but not used [-Wunused-but-set-variable]
Remove unused variable delta_i_ua.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
Eliminate the follow coccicheck warning:
./drivers/power/supply/da9150-fg.c:524:2-9: line 524 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are a few spelling mistakes in comments and in a dev_err
error message. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We add the line impedance to the inner resistance determined
from the battery voltage or other means to improve the
capacity estimations.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In free_charger_irq(), there is no free for 'WM8350_IRQ_CHG_FAST_RDY'.
Therefore, it should be better to add it in order to avoid the memory leak.
Fixes: 14431aa0c5 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we detect a Samsung SDI battery, we return a static
struct power_supply_battery_info and avoid looking further.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Augment the AB8500 fuel gauge to use the VBAT-to-Ri method of
estimating the internal resistance if possible. Else fall back
to using the temperature-to-Ri or just the default Ri.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In Samsung devices, the method used to compensate for temperature,
age, load etc is by way of VBAT to Ri tables, which correlates the
battery voltage under load (VBAT) to an internal resistance (Ri).
Using this Ri and a measurement of the current out of the battery
(IBAT) the open circuit voltage (OCV) can be calculated as:
OCV = VBAT - (Ri * IBAT)
The details are described in comments to struct
power_supply_battery_info in the commit.
Since not all batteries supply this VBAT-to-Ri data, the fallback
method to use the temperature-to-Ri lookup table can also be used
as a fallback.
Add two helper functions to check if we have the tables needed for
using power_supply_vbat2ri() or power_supply_temp2resist_simple()
respectively, so capacity estimation code can choose which one
to employ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Battery Type Indicator (BTI) resistor is a resistor mounted
between a special terminal on the battery and ground. By sending
a fixed current (such as 7mA) through this resistor and measuring
the voltage over it, the resistance can be determined, and this
verifies the battery type.
Typical side view of the battery:
o o o
GND BTI +3.8V
Typical example of the electrical layout:
+3.8 V BTI
| |
| + |
_______ [ ] 7kOhm
___ |
| |
| |
GND GND
By verifying this resistance before attempting to charge the
battery we add an additional level of security.
In some systems this is used for plug-and-play of batteries with
different capacity. In other cases, this is merely used to verify
that the right type of battery is connected, if several batteries
have the same physical shape and can be plugged into the same
slot. Sometimes this is just a surplus security mechanism.
Nokia and Samsung among many other vendors are known to use these
BTI resistors.
Add the BTI properties to struct power_supply_battery_info and
switch the AB8500 charger code over to using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 code is using a special current and voltage setting
when the battery is in "alert mode", i.e. when it is starting
to go outside normal operating conditions so it is too
cold or too hot. This makes sense as a way for the charging
algorithm to deal with hostile environments.
Add the needed members to the struct power_supply_battery_info,
and switch the AB8500 charging code over to using this.
Reviewed-by: Matti Vaittineen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Maintenance charging is the phase of keeping up the charge
after the battery has charged fully using CC/CV charging.
This can be done in many successive phases and is usually
done with a slightly lower constant voltage than CV, and
a slightly lower allowed current.
Add an array of maintenance charging points each with a
current, voltage and safety timer, and add helper functions
to use these. Migrate the AB8500 code over.
This is used in several Samsung products using the AB8500
and these batteries and their complete parameters will
be added later as full examples, but the default battery
in the AB8500 code serves as a reasonable example so far.
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Recently userspace has started switching power_supply class devices with
a charge_type psy-property between fast and trickle charge mode, see:
https://gitlab.freedesktop.org/hadess/power-profiles-daemon/-/issues/85
Before this patch bq24190_charger_set_charge_type() would unconditionally
write charging or none to the BQ24190_REG_POC_CHG_CONFIG bits, replacing
the otg setting of those bits when the OTG 5V Vbus boost converter was on,
turning the 5V Vbus off, removing the power from any attached peripherals.
This fixes this by keeping track of otg_vbus_enabled and the requested
charger_type settings and when otg_vbus_enabled is true, delay applying
the charger_type until the 5V boost converter is turned off.
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_delayed_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver only uses managed resources, except for the delayed work, if
it is used.
Use devm_delayed_work_autocancel() to also manage the delayed work.
The error handling path of the probe and the remove function can both be
removed.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver can use an interrupt or polling in order get the charger's
status.
When using polling, a delayed work is used.
However, the remove() function unconditionally call
cancel_delayed_work_sync(), even if the delayed work is not used and is not
initialized.
In order to fix it, use devm_delayed_work_autocancel() and remove the now
useless remove() function.
Fixes: feb583e37f ("power: supply: add sbs-charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch remaps the bypass operation from POWER_SUPPLY_CHARGE_TYPE_FAST
to POWER_SUPPLY_CHARGE_TYPE_BYPASS.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds a POWER_SUPPLY_CHARGE_TYPE_BYPASS option to the POWER_SUPPLY_PROP_CHARGE_TYPE
property to facilitate bypass charging operation.
In bypass charging operation, the charger bypasses the charging path around the
integrated converter allowing for a "smart" wall adaptor to perform the power
conversion externally.
This operational mode is critical for the USB PPS standard of power adaptors and is
becoming a common feature in modern charging ICs such as:
- BQ25980
- BQ25975
- BQ25960
- LN8000
- LN8410
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_work_autocancel() instead of hand-writing it.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The smb347 has a very sparse register map (the maximum register is 0x3f but
less than 10% of the possible registers appear to be defined) and doesn't
have any hardware defaults specified so the sparser data structure of an
rbtree is a better fit for it's needs than a flat cache. Since it uses I2C
for the control interface there is no performance concern with the slightly
more involved code so let's convert it.
This will mean we avoid any issues created by assuming that any previously
unaccessed registers hold a value that doesn't match what's in the hardware
(eg, an _update_bits() suppressing a write).
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.
For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.
This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.
As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.
Set Vhold to 4.4V to fix the slow charging issue on various devices.
There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.
Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace dev_err() with dev_err_probe() in probe() and extend register
access failure messages. dev_err()s in _reset() are removed as they
are redundant: register access wrappers already log the error.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace two divisions with a subtraction+shift for a small code size
improvement and less brackets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
fix the comment typo: "interrupts", "structcure"
Signed-off-by: Hong Peng <elicec@foxmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 8c0984e5a7 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This change makes the PCHG driver receive device events through
MKBP protocol since CrOS EC switched to deliver all peripheral
charge events to the MKBP protocol. This will unify PCHG event
handling on X86 and ARM.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since we now return a pointer to an allocated object we need
to account for memory allocation failure in a separate
error path.
Fixes: 25fd330370 ("power: supply_core: Pass pointer to battery info")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When using USB charging, the AB8500 charger is periodically
checking VBAT for a threshold at 3.8V.
This crashes badly, as the class_for_each_device() was passed
the wrong argument. I think this has maybe worked by chance
in the past because of how the structs were arranged but it
is leading to crashes now.
Fix this up and also switch to using microvolts for the
voltages like the rest of the code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8505 only has two ADC channels: the voltage and current
provided from VBUS (USB). It does not support AC charging at all.
Make sure we don't try to retrieve the non-existing channels.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a sysfs ABI to enable/disable charging of different
types (AC/USB).
Since we don't have any userspace for this code, this sits
unused and it is not used on production products either.
Drop this code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a sysfs ABI to change the "charging step" of the
charger i.e. limit how much we charge from userspace.
Since we don't have any userspace for this code, this sits
unused and it is not used on production products either.
Drop this code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
All calls to ab8500_fg_calc_cap_discharge_voltage() require
compensation and pass true as the second argument so just drop
this argument.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In some cases when the platform is dissapating more than
500mA the voltage measurements and compensation will become
instable. Add a parameter to bail out of the voltage
measurement if this happens.
This code was found in a Samsung vendor tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Break out the part of the function providing the load compensated
capacity that provides the load compensated voltage and use
that to get the load compensated capacity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the Samsung code tree we find that it can happen that this
measurement loop goes on for a long time, and it seems like a
good idea to break it after 70 iterations if it goes on for
too long.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of providing our own homebrewn thermal measurement
code for an NTC and passing tables, we put the NTC thermistor
into the device tree, create a passive thermal zone, and poll
this thermal zone for the temperature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We should terminate charging when we reach the voltage_max_design_uv
not overvoltage_limit_uv, this is an abuse of that struct member.
The overvoltage limit is actually not configurable on the AB8500,
it is fixed to 4.75 V so drop a comment about that in the code.
Fixes: 2a5f41830a ("power: supply: ab8500: Standardize voltages")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BATCTRL mode reads the temperature of the battery by
enabling a certain probing current (7-20 mA) and then measure
the voltage of the NTC mounted inside the battery.
None of the AB8500 product or the reference designs use this
mode. What we use is the so-called BATTEMP mode which enables
an internal 230 kOhm pull-up to 1.8 V to the external NTC on
pin BatTemp (N16) and then measures the voltage over the NTC
using the ADC:
1.8V (VTVOUT)
|
[ ] 230 kOhm
|
BatTemp +---------------- ADC
Pin N16 | _
|/
[/] NTC
_/|
|
GND
Cut out the BATCTRL code to clear the forest and stop
maintaining code we can never test.
The current inducing method is still used to probe for the
battery type using the internal BTI (battery type indicator)
on the BatCtrl (C3) pin in a separate code path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use device_property_string_array_count() to get number of strings
in a string array property.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When ret is not zero there were already one or two error messages emitted
about a problem (because rt9455_register_reset() emits a message in most
cases then). Passing on that error code to the i2c core only results in
another error message. Suppress that by returning zero unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_bitmap_zalloc() instead of hand writing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a new battery driver for the uPI uG3105 battery monitor.
Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead it
is expected to be use in combination with some always on microcontroller
reading its coulomb-counter before it can wrap (must be read every 400
seconds!).
Since Linux does not monitor coulomb-counter changes while the device is
off or suspended, the coulomb counter is not used atm.
So far this driver is only used on x86/ACPI (non devicetree) devs
(also note there is no of_match table). Therefor there is no devicetree
bindings documentation for this driver's "upisemi,rsns-microohm" property
since this is not used in actual devicetree files and the dt bindings
maintainers have requested properties with no actual dt users to
_not_ be added to the dt bindings.
The property's name has been chosen so that it should not need to be
changed if/when devicetree enumeration support gets added later, as it
mirrors "maxim,rsns-microohm" from the "maxim,max17042" bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If the fwnode data as parsed by power_supply_get_battery_info() provides
max values for ccc_ireg and cvc_vreg then do not allow the user to later
set these to higher values then those specified by the firmware,
otherwise the battery might get damaged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
So far the bq24190_charger driver has been relying on either the chips
default constant_charge_current_max_ua and constant_charge_voltage_max_uv
values, or on the BIOS or bootloader to program these for us.
This does not happen on all boards, causing e.g. the wrong (too low)
values to be used on Lenovo Yoga Tablet 2 830F/L and 1050F/L tablets.
If power_supply_get_battery_info() provides us with values for these
settings, then program the charger accordingly.
And if the user later overrides these values then save the user-values
so that these will be restored after a suspend/resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Store ichg-max and vreg-max in bq24190_dev_info once from
bq24190_get_config() and drop the bq24190_charger_get_current_max() and
bq24190_charger_get_voltage_max() helpers.
This is a preparation patch for honoring the
constant_charge_current_max_ua and constant_charge_voltage_max_uv
values from power_supply_get_battery_info().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
power_supply_get_battery_info() now also supports getting battery_info
on boards not using dt/of. Remove the of_node check. If neither of nor
other battery-info is present the function will fail making this change
a no-op in that case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Turn off the 5V boost regulator on shutdown, there are 3 reasons for
doing this:
1. It drains he battery if left on
2. If left on the device will not charge when plugged into a charger
3. If left on and the powered peripheral attached to a Type-C port is
removed before the next boot, then the Type-C port-controller will
see VBus being present while nothing is attached confusing the
TCPM state-machine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support to power_supply_get_battery_info() to read the properties from
other fwnode types such as swnodes added by platform code on x86 devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch power_supply_get_battery_info() over to use the generic
fwnode_property_*() property read functions. This is a preparation patch
for adding support for reading properties from other fwnode types such
as swnode properties added by platform code on x86 devices.
Note the parsing of the 2d matrix "ocv-capacity-table-%d" and
"resistance-temp-table" properties is not converted since this depends on
the raw of_get_property() accessor function of which there is no
fwnode_property_*() equivalent AFAICT. This means that these properties
will not be supported in swnodes for now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a spelling mistake in a MODULE_PARM_DESC description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This immutable branch fixes the charger setup on Xiaomi Mi Pad 2 and
Lenovo Yogabook, which requires updates to multiple drivers throughout
the tree.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----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=8iWn
-----END PGP SIGNATURE-----
Merge tag 'psy-extcon-i2c-mfd-for-v5.18-signed' into psy-next
Immutable branch between power-supply, mfd, i2c and extcon for for 5.18
This immutable branch fixes the charger setup on Xiaomi Mi Pad 2 and
Lenovo Yogabook, which requires updates to multiple drivers throughout
the tree.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the devm_regmap_field_bulk_alloc() helper function instead of
open-coding this ourselves.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a "linux,pump-express-vbus-max" property which indicates if the Pump
Express+ protocol should be used to increase the charging protocol.
If this new property is set and a DCP charger is detected then request
a higher charging voltage through the Pump Express+ protocol.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Changes by Hans de Goede:
- Port to my bq25890 patch-series + various cleanups
- Make behavior configurable through a new "linux,pump-express-vbus-max"
device-property
- Sleep 1 second before re-checking the Vbus voltage after requesting
it to be raised, to ensure that the ADC has time to sampled the new Vbus
- Add VBUSV bq25890_tables[] entry and use it in bq25890_get_vbus_voltage()
- Tweak commit message
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25892 does not have builtin charger-type detection like the bq25980,
there might be some external charger detection capability, which will be
modelled as a power_supply class-device supplying the bq25892.
Use the usb_type property value from the supplier psy-device to set the
input-current-limit (when available).
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25890_charger code supports enabling/disabling the boost converter
based on usb-phy notifications. But the usb-phy framework is not used on
all boards/platforms. At support for registering the Vbus boost converter
as a standard regulator when there is no usb-phy on the board.
Also add support for providing regulator_init_data through platform_data
for use on boards where device-tree is not used and the platform code must
thus provide the regulator_init_data.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a bq25890_set_otg_cfg() helper function, this is a preparation
patch for adding regulator support.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the "if (!dev->platform_data)" check, this seems to be an attempt
for allowing loading the driver on devices without devicetree stemming
from the initial commit of the driver (with the presumed intention being
the "return -ENODEV" else branch getting replaced with something else).
With the new "linux,skip-init" and "linux,read-back-settings" properties
the driver can actually supports devices without devicetree and this
check no longer makes sense.
While at it, also switch to dev_err_probe(), which is already used in
various other places in the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On boards where the "linux,skip-reset" boolean property is set we don't
reset the charger; and on some boards where the fw takes care of
initalizition F_CHG_CFG is set to 0 before handing control over to the OS.
Explicitly set F_CHG_CFG to 1 on boards where we don't reset the charger,
so that charging is always enabled on these boards, like it is always
enabled on boards where we do reset the charger.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On most x86/ACPI devices there is no devicetree to supply the necessary
init-data. Instead the firmware already fully initializes the bq25890
charger at boot. To support this, add support for reading back the
settings from the chip through a new "linux,read-back-settings" boolean.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On most x86/ACPI devices the firmware already fully initializes
the bq25890 charger at boot, in this case it is best to not reset
it at probe() time.
At support for a new "linux,skip-reset" boolean property to support this.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On most x86/ACPI devices there is no devicetree to supply the necessary
init-data. Instead the firmware already fully initializes the bq25890
charger at boot.
Factor out the current code to write all the init_data from devicetree
into a new bq25890_rw_init_data() helper which can both write the data
to the charger (the current behavior) as well as read it back from
the charger into the init_data struct.
This is a preparation patch for adding support for x86/ACPI device's
where the init_data must be read back from the bq25890 charger.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Take into account possible current reduction due to low-temperature when
reading POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX. As described in
the datasheet in cool (0-20° Celcius) conditions the current limit is
decreased to 20% or 50% of ICHG field value depended on JEITA_ISET field.
Also add NTC_FAULT field value to the debug message in
bq25890_get_chip_state().
Changed by Hans de Goede:
- Fix reading F_CHG_FAULT instead of F_NTC_FIELD for state->ntc_fault
- Only read JEITA_ISET field if necessary
- Tweak commit message a bit
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rename the Input Current Limit field in the REG00 from IILIM to IINLIM
accordingly with the bq2589x datasheet. This is just cosmetical change
to reduce confusion.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some (USB) charger ICs have variants with USB D+ and D- pins to do their
own builtin charger-type detection, like e.g. the bq24190 and bq25890 and
also variants which lack this functionality, e.g. the bq24192 and bq25892.
In case the charger-type; and thus the input-current-limit detection is
done outside the charger IC then we need some way to communicate this to
the charger IC. In the past extcon was used for this, but if the external
detection does e.g. full USB PD negotiation then the extcon cable-types do
not convey enough information.
For these setups it was decided to model the external charging "brick"
and the parameters negotiated with it as a power_supply class-device
itself; and power_supply_set_input_current_limit_from_supplier() was
introduced to allow drivers to get the input-current-limit this way.
But in some cases psy drivers may want to know other properties, e.g. the
bq25892 can do "quick-charge" negotiation by pulsing its current draw,
but this should only be done if the usb_type psy-property of its supplier
is set to DCP (and device-properties indicate the board allows higher
voltages).
Instead of adding extra helper functions for each property which
a psy-driver wants to query from its supplier, refactor
power_supply_set_input_current_limit_from_supplier() into a
more generic power_supply_get_property_from_supplier() function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some boards with an AXP288 fuel-gauge appear to have a broken (approx.
2 milli-ohm instead of 10) current sense resistor.
This makes the coulomb-counter part of the fuel-gauge useless, but the
OCV based capacity reporting is still working. Add a no_current_sense_res
module_param to disable use of the coulomb-counter using parts of the
fuel-gauge to allow users to work around this.
Note this is a module parameter and not done through DMI quirks, since
this seems to be a defect on some boards, not something which all boards
of the same model share.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The valid flag is protected by the mutex, so code clearing it
should take the mutex before cleating the valid flag.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Refactor the IRQ initialization code:
* Move the looking up of the vIRQs to the beginning of probe(), failing
probe early if this fails
* Do the actual requesting of IRQs inline in probe() and properly abort
probe() on errors
* Use devm_request_threaded_irq(), completing the conversion of probe() to
only use devm managed resources and remove the remove() driver function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_power_supply_register() instead of
power_supply_register().
Note as a side-effect this changes the release order so that now
first the IRQs get free-ed and then the psy gets unregistered.
This is actually a bug-fix since this fixes the IRQ possibly trying
to reference the unregistered psy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
An existing comment already mentions we: "cannot use devm_iio_channel_get
because x86 systems lack the device<->channel maps which iio_channel_get
will try to use when passed a non NULL device pointer".
Work around this by registering a devm action to free the iio-channels.
This is a step on the way to fully converting the probe() function to
only use devm managed resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Refactor probe a bit, introducing a new
axp288_fuel_gauge_read_initial_regs() helper. This replaces a whole
bunch of gotos and removes the unblock_punit_i2c_access label.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a dev local variable to probe() as shortcut for &pdev->dev, this is
a preparation change for making more use of devm managed resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This allows cpcap-battery to detect whitch battery is inserted, HW4X or
BW8X for xt875 and EB41 for xt894 by examining the battery nvmem. If no
known battery is detected sane defaults are used.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As stated in [1], negative current values are used for discharging
batteries.
AXP PMICs internally have two different ADC channels for shunt current
measurement: one used during charging and one during discharging.
The values reported by these ADCs are unsigned.
While the driver properly selects ADC channel to get the data from,
it doesn't apply negative sign when reporting discharging current.
[1] Documentation/ABI/testing/sysfs-class-power
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Calling platform_get_irq_optional() doesn't make sense if you then bail out
on any error it returns. Switch to calling platform_get_irq() instead and
remove dev_err() call as platform_get_irq() already curses loudly on error.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/power/supply/cros_usbpd-charger.c:107:23: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field. Move the ab8500 power supply sysfs code to use default_groups
field which has been the preferred way since aa30f47cf6 ("kobject: Add
support for default attribute groups to kobj_type") so that we can soon
get rid of the obsolete default_attrs field.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Link: https://lore.kernel.org/r/20211229140908.2523513-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Highlights:
- new drivers:
- asus-tf103c-dock
- intel_crystal_cove_charger
- lenovo-yogabook-wmi
- simatic-ipc platform-code + led driver + watchdog driver
- x86-android-tablets (kernel module to workaround DSDT bugs on these)
- amd-pmc:
- bug-fixes
- smar trace buffer support
- asus-wmi: support for custom fan curves
- int3472 (camera info ACPI object for Intel IPU3/SkyCam cameras):
- ACPI core + int3472 changes to delay enumeration of camera sensor I2C
clients until the PMIC for the sensor has been fully probed
- Add support for board data (DSDT info is incomplete) for setting up
the tps68470 PMIC used on some boards with these cameras
- Add board data for the Microsoft Surface Go (original, v2 and v3)
- thinkpad_acpi:
- various cleanups
- support for forced battery discharging (for battery calibration)
- support to inhibit battery charging
- this includes power_supply core changes to add new APIs for this
- think_lmi: enhanced BIOS password support
- various other small fixes and hardware-id additions
The following is an automated git shortlog grouped by driver:
ACPI:
- delay enumeration of devices with a _DEP pointing to an INT3472 device
Add Asus TF103C dock driver:
- Add Asus TF103C dock driver
Add intel_crystal_cove_charger driver:
- Add intel_crystal_cove_charger driver
Documentation:
- syfs-class-firmware-attributes: Lenovo Opcode support
Merge tag 'platform-drivers-x86-int3472-1' into review-hans:
- Merge tag 'platform-drivers-x86-int3472-1' into review-hans
amd-pmc:
- only use callbacks for suspend
- Add support for AMD Smart Trace Buffer
- Simplify error handling and store the pci_dev in amd_pmc_dev structure
- Fix s2idle failures on certain AMD laptops
- Make CONFIG_AMD_PMC depend on RTC_CLASS
apple-gmux:
- use resource_size() with res
asus-wmi:
- Reshuffle headers for better maintenance
- Split MODULE_AUTHOR() on per author basis
- Join string literals back
- remove unneeded semicolon
- Add support for custom fan curves
dell-wmi-descriptor:
- disable by default
hp_accel:
- Use SIMPLE_DEV_PM_OPS() for PM ops
- Fix an error handling path in 'lis3lv02d_probe()'
i2c:
- acpi: Add i2c_acpi_new_device_by_fwnode() function
- acpi: Use acpi_dev_ready_for_enumeration() helper
int3472:
- Add board data for Surface Go 3
- Deal with probe ordering issues
- Pass tps68470_regulator_platform_data to the tps68470-regulator MFD-cell
- Pass tps68470_clk_platform_data to the tps68470-regulator MFD-cell
- Add get_sensor_adev_and_name() helper
- Split into 2 drivers
intel-uncore-frequency:
- use default_groups in kobj_type
intel_pmc_core:
- fix memleak on registration failure
leds:
- simatic-ipc-leds: add new driver for Siemens Industial PCs
lenovo-yogabook-wmi:
- Add support for hall sensor on the back
- Add driver for Lenovo Yoga Book
lg-laptop:
- Recognize more models
platform:
- surface: Propagate ACPI Dependency
platform/mellanox:
- mlxbf-pmc: Fix an IS_ERR() vs NULL bug in mlxbf_pmc_map_counters
- mlxreg-lc: fix error code in mlxreg_lc_create_static_devices()
platform/surface:
- aggregator_registry: Rename device registration function
- aggregator_registry: Use generic client removal function
- aggregator: Make client device removal more generic
platform/x86/intel:
- Remove X86_PLATFORM_DRIVERS_INTEL
- hid: add quirk to support Surface Go 3
platform_data:
- Add linux/platform_data/tps68470.h file
pmc_atom:
- improve critclk_systems matching for Siemens PCs
power:
- supply: Provide stubs for charge_behaviour helpers
- supply: fix charge_behaviour attribute initialization
- supply: add helpers for charge_behaviour sysfs
- supply: add charge_behaviour attributes
samsung-laptop:
- Fix typo in a comment
simatic-ipc:
- add main driver for Siemens devices
system76_acpi:
- Guard System76 EC specific functionality
think-lmi:
- Prevent underflow in index_store()
- Simplify tlmi_analyze() error handling a bit
- Move kobject_init() call into tlmi_create_auth()
- Opcode support
- Abort probe on analyze failure
thinkpad_acpi:
- support inhibit-charge
- support force-discharge
- Add lid_logo_dot to the list of safe LEDs
- Add LED_RETAIN_AT_SHUTDOWN to led_class_devs
- Remove unused sensors_pdev_attrs_registered flag
- Fix the hwmon sysfs-attr showing up in the wrong place
- tpacpi_attr_group contains driver attributes not device attrs
- Register tpacpi_pdriver after subdriver init
- Restore missing hotkey_tablet_mode and hotkey_radio_sw sysfs-attr
- Fix thermal_temp_input_attr sorting
- Remove "goto err_exit" from hotkey_init()
- Properly indent code in tpacpi_dytc_profile_init()
- Cleanup dytc_profile_available
- Simplify dytc_version handling
- Make *_init() functions return -ENODEV instead of 1
- Accept ibm_init_struct.init() returning -ENODEV
- Convert platform driver to use dev_groups
- fix documentation for adaptive keyboard
- Fix WWAN device disabled issue after S3 deep
- Add support for dual fan control
tools/power/x86/intel-speed-select:
- v1.11 release
- Update max frequency
touchscreen_dmi:
- Remove the Glavey TM800A550L entry
- Enable pen support on the Chuwi Hi10 Plus and Pro
- Correct min/max values for Chuwi Hi10 Pro (CWI529) tablet
- Add TrekStor SurfTab duo W1 touchscreen info
watchdog:
- simatic-ipc-wdt: add new driver for Siemens Industrial PCs
wmi:
- Add no_notify_data flag to struct wmi_driver
- Fix driver->notify() vs ->probe() race
- Replace read_takes_no_args with a flags field
x86-android-tablets:
- Fix GPIO lookup leak on error-exit
- Add TM800A550L data
- Add Asus MeMO Pad 7 ME176C data
- Add Asus TF103C data
- Add support for preloading modules
- Add support for registering GPIO lookup tables
- Add support for instantiating serdevs
- Add support for instantiating platform-devs
- Add support for PMIC interrupts
- Don't return -EPROBE_DEFER from a non probe() function
- New driver for x86 Android tablets
x86/platform/uv:
- use default_groups in kobj_type
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmHcCbkUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9y3yAf/Xo8TWsnF7XoS3pNCqRcObIulHy6u
9AOD4gTb0p9LiAd8WN75UsQDew0Rib+UDTS3s6g9l71fMzpTFOD4IaBPrVAmIxpu
Qs9raFTH67CFid/V3DCwAjPQYxxp5LBGvYJ4oy3OmaYHieV9jdsvNLISlpi/V8wR
PmbmYtiK5TPZwRT+mknq89D+LynP2NYkvoqRitmB7MrAvxY3c0ssrex6dXMrdgqK
ehRtfz/ER8xQ03APIzHG+ec73LZsHCMDDG7teas4tiMlMaWGgRO2I8GAudjuPEoy
mBTSb3ABuEud8LTMgjB+trM2w9IAoFE0L6/OrKE5dK1tPdaLxvCuuSVheQ==
=tmPR
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
New drivers:
- asus-tf103c-dock
- intel_crystal_cove_charger
- lenovo-yogabook-wmi
- simatic-ipc platform-code + led driver + watchdog driver
- x86-android-tablets (kernel module to workaround DSDT bugs on
these)
amd-pmc:
- bug-fixes
- smar trace buffer support
asus-wmi:
- support for custom fan curves
int3472 (camera info ACPI object for Intel IPU3/SkyCam cameras):
- ACPI core + int3472 changes to delay enumeration of camera sensor
I2C clients until the PMIC for the sensor has been fully probed
- Add support for board data (DSDT info is incomplete) for setting up
the tps68470 PMIC used on some boards with these cameras
- Add board data for the Microsoft Surface Go (original, v2 and v3)
thinkpad_acpi:
- various cleanups
- support for forced battery discharging (for battery calibration)
- support to inhibit battery charging
- this includes power_supply core changes to add new APIs for this
think_lmi:
- enhanced BIOS password support
various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (78 commits)
power: supply: Provide stubs for charge_behaviour helpers
platform/x86: x86-android-tablets: Fix GPIO lookup leak on error-exit
platform/x86: int3472: Add board data for Surface Go 3
platform/x86: Add Asus TF103C dock driver
platform/x86: x86-android-tablets: Add TM800A550L data
platform/x86: x86-android-tablets: Add Asus MeMO Pad 7 ME176C data
platform/x86: x86-android-tablets: Add Asus TF103C data
platform/x86: x86-android-tablets: Add support for preloading modules
platform/x86: x86-android-tablets: Add support for registering GPIO lookup tables
platform/x86: x86-android-tablets: Add support for instantiating serdevs
platform/x86: x86-android-tablets: Add support for instantiating platform-devs
platform/x86: x86-android-tablets: Add support for PMIC interrupts
platform/x86: x86-android-tablets: Don't return -EPROBE_DEFER from a non probe() function
platform/x86: touchscreen_dmi: Remove the Glavey TM800A550L entry
platform/x86: touchscreen_dmi: Enable pen support on the Chuwi Hi10 Plus and Pro
platform/x86: touchscreen_dmi: Correct min/max values for Chuwi Hi10 Pro (CWI529) tablet
platform/x86: Add intel_crystal_cove_charger driver
power: supply: fix charge_behaviour attribute initialization
platform/x86: intel-uncore-frequency: use default_groups in kobj_type
x86/platform/uv: use default_groups in kobj_type
...
power-supply core:
- introduce "No Battery" health status
- use library interpolation
- add power_supply_battery_info documentation
- migrate power_supply_battery_info to be fully heap allocated
making it more obvious that it needs to be free'd manually
Drivers:
- max77976-charger: new driver
- qcom-smbb: add pm8226 charger support
- bq25890-charger: support battery temperature readings
- ab8500: continue migrating towards using standard core APIs
-----BEGIN PGP SIGNATURE-----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=9cda
-----END PGP SIGNATURE-----
Merge tag 'for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce "No Battery" health status
- use library interpolation
- add power_supply_battery_info documentation
- migrate power_supply_battery_info to be fully heap allocated making
it more obvious that it needs to be free'd manually
Drivers:
- max77976-charger: new driver
- qcom-smbb: add pm8226 charger support
- bq25890-charger: support battery temperature readings
- ab8500: continue migrating towards using standard core APIs"
* tag 'for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
power: supply_core: Pass pointer to battery info
power: supply: ab8500: Fix the error handling path of ab8500_charger_probe()
power: reset: mt6397: Check for null res pointer
power: bq25890: add POWER_SUPPLY_PROP_TEMP
power: supply: qcom_smbb: support pm8226
dt-bindings: power: supply: pm8941-charger: add pm8226
power: supply: ab8500: Standardize capacity lookup
power: supply: ab8500: Standardize temp res lookup
power: supply: ab8500: Standardize CV voltage
power: supply: ab8500: Standardize CC current
power: supply: ab8500: Make recharge capacity a constant
power: supply: ab8500: Standardize termination current
power: supply: ab8500: Standardize internal resistance
power: supply: ab8500_fg: Init battery data in bind()
power: supply: ab8500: Standardize voltages
power: supply: ab8500: Standardize technology
power: supply: ab8500: Standardize design capacity
power: supply: ab8500: Use only one battery type
power: supply: ab8500: Drop unused battery types
power: supply: ab8500: Standardize operating temperature
...
All properties have to be added to power_supply_attrs which was missed
before.
Fixes: 1b0b6cc803 ("power: supply: add charge_behaviour attributes")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20220105064239.2689-1-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The function to retrieve battery info (from the device tree) assumes
we have a static info struct that gets populated by calling into
power_supply_get_battery_info().
This is awkward since I want to support tables of static battery
info by just assigning a pointer to all info based on e.g. a
compatible value in the device tree.
We also have a mixture of static and dynamically allocated
variables here.
Bite the bullet and let power_supply_get_battery_info() allocate
also the memory used for the very top level
struct power_supply_battery_info container. Pass pointers
around and lifecycle this with the psy device just like the
stuff we allocate inside it.
Change all current users over.
As part of the change, initializers need to be added to some
previously uninitialized fields in struct
power_supply_battery_info.
Reviewed-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the commit below, ab8500_bm_of_remove() needs to be called after a
successful ab8500_bm_of_probe() call.
This commit has only updated the remove function.
Fix the error handling path of the probe the same way.
Fixes: 6252c706cd ("power: supply: ab8500: Standardize operating temperature")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The return value of platform_get_resource() needs to be checked.
To avoid use of error pointer in case that there is no suitable
resource.
Fixes: d28c74c107 ("power: reset: add driver for mt6323 poweroff")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
These helper functions can be used by drivers to implement their own
sysfs-attributes.
This is useful for ACPI-drivers extending the default ACPI-battery with
their own charge_behaviour attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20211123232704.25394-3-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the POWER_SUPPLY_PROP_TEMP and a NTC 10K percent VREGN to degrees LUT.
Make sure that a conversion is forced when the power supply is offline so
the temperature is valid.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
PM8226 (used in MSM8226) has v1 smbb hardware and works fine with the
current driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 charger only has one capacity table with
unspecified temperature, so we assume this capacity is given
for 20 degrees Celsius.
Convert this table to use the OCV (open circuit voltage)
tables in struct power_supply_battery_ocv_table.
In the process, convert the fuel gauge driver to use
microvolts and microamperes so we can use the same internals
as the power supply subsystem without having to multiply
and divide with 1000 in a few places.
Also convert high_curr_threshold and lowbat_threshold to
use microamperes and microvolts as these are closely
related to these changes.
Drop the unused overbat_threshold member in the custom
struct ab8500_fg_parameters.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The lookup from battery temperature to internal resistance was
using its own format. Rewrite this to use the table inside
struct power_supply_battery_info:s resist_table.
The supplied resistance table has to be rewritten to express
the resistance in percent of the factory resistance as a
side effect.
We can then rely on the library function
power_supply_temp2resist_simple() to interpolate the internal
resistance percent from the temperature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The voltage used in the constant voltage phase of the charging
exist in struct power_supply_battery_info as
constant_charge_voltage_max_uv.
Switch the custom property normal_vol_lvl to this and
consequentially change everything that relates to this value
over to using microvolts rather than millivolts so
we align internal representation of current with the
power core. Prefix every variable we change with *_uv
to indicate the unit everywhere but also to make sure
we do not miss any outlier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The current used in the constant current phase of the charging
exist in struct power_supply_battery_info as
constant_charge_current_max_ua.
Switch the custom property max_out_curr to this and
consequentally change everything that relates to this value
over to using microamperes rather than milliamperes so
we align internal representation of current with the
power core. Prefix every variable we change with *_ua
to indicate the unit everywhere but also to make sure
we do not miss any outlier.
Drop some duplicate unused defines in a header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The recharge capacity is the hysteresis level for a charger to
restart when a battery does not support maintenance charging.
All products using the AB8500 have batteries supporting
maintenace charging and all code has always set this to 95%.
Turn it into a constant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 custom termination current can be replaced by the
corresponding struct power_supply_battery_info field.
Remove the struct member and amend the code to use the
standard property.
Add *_ua suffix for clarity and to make sure we have
changed all code sites using this member.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The nominal internal resistance isn't used by the AB8500
charging code, instead this resistance is measured continuously,
but we anyways migrate this to the standard property in
struct power_supply_battery_info.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We were assigning some battery data state in probe() but
this is insecure as it depends on the proper probe order
between the components: the charger must probe first so
that the battery data is populated. Move the init to
the bind() call which is certain to happen after the
probe of the master and all components has happened.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The nominal voltage in this charge driver corresponds to
both the voltage_min_design_uv and voltage_max_design_uv
of struct power_supply_battery_info so assign both if this
is undefined.
The overcharge max voltage (when the charger should cut off)
is migrated at the same time so we move both voltages to
struct power_supply_battery_info.
Adjust the code to deal directly with the microvolt values
instead of converting them to millivolts.
Add *_uv suffixes for clarity and to make sure we have
changed all code sites using this member.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 custom battery type can be replaced by the
corresponding struct power_supply_battery_info field.
Remove the struct member and amend the code to use the
standard property.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that we know that we have only one battery type to
deal with we can proceed to transfer properties to
struct power_supply_battery_info.
The designed capacity for the battery was in a custom field
of the custom battery type in mAh, transfer this to the
standard charge_full_design_uah property in
struct power_supply_battery_info and augment the code
accordingly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code was going through hoops and loops to detect what
battery is connected and check the resistance for this battery
etc.
Skip this trouble: we will support one battery (currently
"unknown") then we will find the connected battery in the
device tree using a compatible string. The battery resistance
may be used to double-check that the right battery is
connected.
Convert the array of battery types into one battery type so
we can next move over the properties of this one type into
the standard struct power_supply_battery_info.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code tries to detect a lot of battery variants on the reference
designs, but we are not using the reference designs in practice, we
are using real products such as Samsung Phones.
The reference design with no battery plugged in will be detected as
a LIPO battery with a thermistor on the batctrl pin so we will
assume this and later on we can support other types through the
device tree if we want, just like the products do.
Drop the tables for external thermistor, only keep the internal
thermistor tables that we will use as default.
We can delete the assignment of the temperature to resistance table
since the default will be the only and correct option.
Also get rid of some unused variables and unused exports.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of storing the temperature limits in our custom
struct struct ab8500_bm_data, make struct power_supply_battery_info
a member of this and store the min and max temperatures inside
that struct as the temp_min/temp_max and
temp_alert_min/temp_alert_max respectively.
The values can be assigned from the device tree, but if
not present will be set to the same defaults as are currently
in the code.
This way we start to move over to using
struct power_supply_battery_info and make it possible to move
the data over to the device tree and we will move piece by
piece toward using the standard info struct.
Temperature hysteresis is currently not supported by the
standard struct but we move the assignment here as well so
that we have all parameterization in one spot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The two tables for input and output current translation from
register values does not need to be passed around from the
battery manager data. Just push it down into the charger code
where it is used, like other tables in that code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This deploys the core battery DT parser to read the basic properties
of the battery. We only use very little of it as we start out, but
we will improve as we go along.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The power supply core appears to contain two open coded
linear interpolations. Use the kernel fixpoint arithmetic
interpolation library function instead.
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the MAX77976 3.5/5.5A 1-Cell Li+ Battery Charger.
This is a simple implementation enough to be used as a simple battery
charger without OTG and boost.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some chargers can keep the system powered from the mains even when no
battery is present. It this case none of the currently defined health
statuses applies. Add a new status to report that no battery is present.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We should not go on looking for more capacity tables after
we realize we have looked at the last one in
power_supply_find_ocv2cap_table().
Fixes: 3afb50d712 ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code doing the initial setting of the F_CONV_RATE field based
on the bq->state.online flag. In order for this to work properly,
this must be done after the initial bq25890_get_chip_state() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Before this commit the driver was registering its interrupt handler before
it registered the power_supply, causing bq->charger to potentially be NULL
when the interrupt handler runs, triggering a NULL pointer exception in
the interrupt handler:
[ 21.213531] BUG: kernel NULL pointer dereference, address: 0000000000000680
...
[ 21.213573] Hardware name: Xiaomi Inc Mipad2/Mipad, BIOS MIPad-P4.X64.0043.R03.1603071414 03/07/2016
[ 21.213576] RIP: 0010:__lock_acquire+0x5c5/0x1de0
...
[ 21.213629] Call Trace:
[ 21.213636] ? disable_irq_nosync+0x10/0x10
[ 21.213644] ? __mutex_unlock_slowpath+0x35/0x260
[ 21.213655] lock_acquire+0xb5/0x2b0
[ 21.213661] ? power_supply_changed+0x23/0x90
[ 21.213670] ? disable_irq_nosync+0x10/0x10
[ 21.213676] _raw_spin_lock_irqsave+0x48/0x60
[ 21.213682] ? power_supply_changed+0x23/0x90
[ 21.213687] power_supply_changed+0x23/0x90
[ 21.213697] __bq25890_handle_irq+0x5e/0xe0 [bq25890_charger]
[ 21.213709] bq25890_irq_handler_thread+0x26/0x40 [bq25890_charger]
[ 21.213718] irq_thread_fn+0x20/0x60
...
Fix this by moving the power_supply_register() call to above the
request_threaded_irq() call.
Note this fix includes making the following 2 (necessary) changes:
1. Switch to the devm version of power_supply_register() to avoid the
need to make the error-handling in probe() more complicated.
2. Rename the "irq_fail" label to "err_unregister_usb_notifier" since
the old name no longer makes sense after this fix.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add more details to the error messages that indicate what went wrong
and use dev_err_probe() at a few places in the probe() path in order
to avoid error messages for deferred probe after which the driver probes
correctly.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that axp288_charger_usb_update_property() reads and caches all
relevant registers, axp288_get_charger_health() can be simplified
by directly returning the health.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that axp288_charger_usb_update_property() reads and caches all
relevant registers, the axp288_charger_is_present() and
axp288_charger_is_online() helpers are not necessary anymore.
Directly check the cached input_status instead, allowing the removal
of these 2 helpers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add "depends on IOSF_MBI" to CONFIG_AXP288_CHARGER as the changes from
commit ed22945485 ("power: supply: axp288-charger: Optimize register
reading method") use symbols which are only defined when IOSF_MBI support
is enabled.
Depending on this is ok since IOSF_MBI support should always be enabled
on devices which use the AXP288 PMIC.
Fixes: ed22945485 ("power: supply: axp288-charger: Optimize register reading method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Look up the battery using the "monitored-battery" phandle
as is nowadays a standard DT binding. The actual bindings
for these charger elements are not upstream so let's sort
out this mess by conforming to the standard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.
Fixes: ed22945485 ("power: supply: axp288-charger: Optimize register reading method")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d20 ("max17042: Add support for signalling change in SOC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.
Fixes: 7fbf6b731b ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently the rt5033_battery driver provides voltage values in mV. It
should be µV as stated in Documentation/power/power_supply_class.rst.
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The original implementation access the charger the same register value
several times to get the charger status, such as online, enabled, and
bus limits. It takes a long time and bandwidth for every "status get"
operation.
To reduce the access of the register and save bandwidth, this commit
integrated every read operation into only one "register value get"
operation and cache them in the variables. Once the "get properties"
is requested from the user space, the cached information can be returned
immediately.
I2C access between Linux kernel and P-Unit is improved by explicitly taking
semaphore once for the entire set of register accesses in the new
axp288_charger_usb_update_property() function. The I2C-Bus to the XPower
AXP288 is shared between the Linux kernel and SoCs P-Unit. The P-Unit
has a semaphore which the kernel must "lock" before it may use the bus.
If not explicitly taken by the I2C-Driver, then this semaphore is
automatically taken by the I2C-bus-driver for each I2C-transfer. In
other words, the semaphore will be locked and released several times for
entire set of register accesses.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function cpcap_battery_probe(), the driver only needs the
data object, so use device_get_match_data() instead, to make the
code cleaner.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet gives the name IAvg_empty, not LAvg_empty.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a spelling mistake in the name wm831x_battey_apply_config,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If CONFIG_THERMAL=n:
drivers/power/supply/power_supply_core.c: In function ‘__power_supply_register’:
drivers/power/supply/power_supply_core.c:1137:6: error: implicit declaration of function ‘psy_has_property’ [-Werror=implicit-function-declaration]
1137 | if (psy_has_property(desc, POWER_SUPPLY_PROP_USB_TYPE) &&
| ^~~~~~~~~~~~~~~~
Fix this by moving psy_has_property() outside the section protected by
CONFIG_THERMAL.
Fixes: 9ba533eb99 ("power: supply: core: Add psy_has_property()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the helper psy_has_property() to check whether a power supply
has a given property and use it instead of ad hoc iterations over
the property list in multiple locations.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
hrtimer_forward_now() provides the same functionality as the open coded
hrtimer_forward() invocation. Prepares for removal of hrtimer_forward()
from the public interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reorganize the Kconfig driver description and mention all supported
models. This helps when choosing drivers for given system.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reorganize the Kconfig driver description and mention all supported
models. This helps when choosing drivers for given system.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The power_supply_get_battery_info() fails if device-chemistry property
is missing in a device-tree because error variable is propagated to the
final return of the function, fix it.
Fixes: 4eef766b7d ("power: supply: core: Parse battery chemistry/technology")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There's no need to print a message on every change in battery percentage
on regular log levels.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Prepared by checking the datasheets of max17042, max17047/50
and max170455 for differences in register maps.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This register is same as in MAX17047 and MAX17050, so there's no need
for custom casing it.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SMB347 can supply power to USB VBUS, implement the USB VBUS regulator.
USB VBUS needs to be powered for switching OTG-cable USB port into host
mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Utilize generic regmap caching in order to avoid unnecessary slow I2C
accesses to all constant registers each time the supply status updated
and remove local caching of charger state to make code cleaner.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The smb347_set_writable() is used by interrupt handler and outside of it.
The interrupt should be disabled when the function is used outside of
interrupt handler in order to prevent racing with the interrupt context.
Add new parameter to smb347_set_writable() that allows to disable IRQ.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only way to reset the BeagleV Starlight v0.9 board[1] properly is to
tell the PMIC to reset itself which will then assert the external reset
lines of the SoC, USB hub and ethernet phy.
This adds a driver to register a reset handler to do just that.
[1] https://github.com/beagleboard/beaglev-starlight
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
All bits of STATUS register are already defined (see STATUS_SMN_BIT and
further) so there is no need to define status SoC threshold min/max
values one more time.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This extends the struct power_supply_battery_info with a
"technology" field makes the core DT parser optionally obtain
this from the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This commit introduces support for NETGEAR ReadyNAS Duo v2.
This device use bit 4 of LED[2:0] Polarity Control Register to indicate
AC Power loss.
For more details about AC loss detection in NETGEAR ReadyNAS Duo v2,
please look at the file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This commit prepare driver for another device support.
New power_off_cfg structure describes two most important things: name of
mdio bus and pointer to register setting function. It allow to add new
device with different mdio bus node and other phy register config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----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=60NT
-----END PGP SIGNATURE-----
Merge tag 'ib-mt6360-for-5.15-signed' into psy-next
Immutable branch between regulator and power-supply for for 5.15
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename ChargeOption macros to match the others for ChargeCurrent and
ChargeVoltage and also separate the command & masks macros from the bits of
interest macros for each command. This macro doesn't introduce any
functional change, only code re-org.
Signed-off-by: Bruno Meneguele <bruno.meneguele@smartgreen.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read voltage_now via IIO and provide the property.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: kernel test robot <lkp@intel.com> # missing depends on IIO
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add basic support for the battery charger for MT6360 PMIC
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Clean up a handful of checkpatch warnings:
- static const char * array should probably be static const char * const
- function arguments should have identifier names
- else should follow close brace '}'
- suspect code indent for conditional statements
- unnecessary parentheses in an if condition
- avoid multiple line dereference
- remove debug showing function execution, ftrace can trace these better
- prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use the defined variable "dev" to make the code cleaner.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As defined by the Smart Battery Data Specification.
An _AVG suffix is added to the enum values REG_TIME_TO_EMPTY and
REG_TIME_TO_FULL to make the distinction clear.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Smart Battery Data Specification allows for values 0..65535 mV,
there is no reason to limit the value to 20000.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the probe function, when get irq failed, the function
platform_get_irq_byname() logs an error message, so remove
redundant message here.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
MAX77849 is a combined fuel-gauge, charger and MUIC IC. Notably,
fuel-gauge has dedicated i2c lines and seems to be fully compatible
with max17047. Add new compatible for it reusing max17047 code paths.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer and this is a quite expensive operation.
Explicitly take the semaphore in probe() around the register-accesses
done during probe, so that this only needs to be done once, rather then
once per register-access.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer.
Move the AXP20X_CC_CTRL check done in probe() together with the other
register-accesses done in probe, so that we can take the semaphore once
for the entire set of register-accesses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus and while the kernel holds the semaphore the CPU
and GPU power-states must not be changed otherwise the system will freeze.
This is a complex process, which is quite expensive. This is all done by
iosf_mbi_block_punit_i2c_access(). To ensure that no unguarded I2C-bus
accesses happen, iosf_mbi_block_punit_i2c_access() gets called by the
I2C-bus-driver for every I2C transfer. Because this is so expensive it
is allowed to call iosf_mbi_block_punit_i2c_access() in a nested
fashion, so that higher-level code which does multiple I2C-transfers can
call it once for a group of transfers, turning the calls done by the
I2C-bus-driver into no-ops.
Userspace power-supply API users typically will read all provided
properties in one go, refreshing the last read values when
power_supply_changed() is called by the driver and/or periodically
(e.g. every 2 minutes).
The reading of all properties in one go causes the P-Unit semaphore
to quickly be taken and released multiple times in a row. Certain
PMIC registers like AXP20X_FG_RES are even used in multiple properties
so they get read multiple times, leading to a P-Unit take + release
each time the register is read.
As already mentioned the taking of the P-Unit semaphore is a quite
expensive operation and it has also been reported that the
"hammering" of the P-Unit semaphore done by the axp288_fuel_gauge
driver can even cause stability issues with the system as a whole.
Switch over to a scheme where the axp288_fuel_gauge driver keeps
a local copy of all the registers which it uses for properties
and make it only refresh its copy of the registers if the values
are older then 1 minute; or when a fuel-gauge interrupt has
triggered since the last read.
This not only reduces the amount of reads, it also makes the code
do all the reads in one go, rather then reading specific registers
based on which property is being queried. This allows calling
iosf_mbi_block_punit_i2c_access() once before doing all the reads,
so that we now only take the P-Unit semaphore once per update.
Tested-by: Andrejus Basovas <cpp@gcc.lt>
Signed-off-by: Andrejus Basovas <cpp@gcc.lt>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Accessing registers on the AXP288 is quite expensive, so we should avoid
doing unnecessary accesses.
The FG_LOW_CAP_REG never changes underneath us, so we only need to read
it once. Devices with an AXP288 do not have user-replace (let alone
hot-swappable) batteries and the only bit we care about in the
PWR_OP_MODE register is the CHRG_STAT_BAT_PRESENT bit, so we can get
away with only reading the PWR_OP_MODE register once too.
Note that the FG_LOW_CAP_REG is not marked volatile in the regmap, so we
were effectively already reading it once. This change makes this explicit,
this is done as preparation of a further patch which moves all remaining
register accesses in fuel_gauge_get_property() out of that function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Directly store the struct device pointer in axp288_fg_info, rather then
storing a pointer to the struct platform_device there and then using
"&info->pdev->dev" everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. This semaphore is automatically taken by the
I2C-bus-driver.
The retry on -EBUSY logic in fuel_gauge_reg_readb() likely was added to
deal with the I2C-bus-drive returning -EBUSY when it failed to take the
semaphore, but this really should never happen. The semaphore code even
has a WARN_ON(ret) to log a kernel backtrace if this does somehow happen,
when this happens something is seriously wrong and the system typically
freezes soon afterwards.
TL;DR: the regmap_read() should never fail with -EBUSY so the retries
are unnecessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the IRQ mapping messages, because they are really not
interesting at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The debugfs code is simply just dumping a bunch of registers, the same
information can also easily be gotten through the regmap debugfs
interface or through the i2cdump utility.
I've not used the debugfs interface once in all these years that I've
been working on the axp288_fuel_gauge driver, so lets just remove it.
Note this also removes the temperature-channels from the list of
IIO ADC channels used by the driver, since these were only used in the
debugfs interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The values of various defines used in the driver are not aligned
properly when tabsize is set to 8 (I guess they were created with
a different tabsize).
Properly align the defines to make the code easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function sc27xx_fgu_probe(), when get irq failed,
platform_get_irq() logs an error message, so remove
redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
This driver creates a sysfs node for each peripheral charge port:
/sys/class/power_supply/peripheral<n>
where <n> is the index of a charge port.
For example, when a stylus is connected to a NFC/WLC port, the node
returns:
/sys/class/power_supply/peripheral0/
capacity=50
charge_type=Standard
scope=Device
status=Charging
type=Battery
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This file isn't using any AB8500 symbols so drop these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we rename the "abx500_chargalg" supply to "ab8500_chargalg"
as it should be named, the existing supplies are supplying that
supply but that was obviously not working since it had the
wrong name.
Now that the dependency kicks in we get a bunch
of NULL references from ab8500_chargalg_external_power_changed()
so check that the workqueue is allocated before we try to
queue work on it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the entire idea with abx500 being abstract and different from ab8500
in the AB8500 charging drivers. This rids the two identical definitions
of a slew of structs in ab8500-bm.h and makes things less confusion and
easier to understand.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "abx500" name on the charging algorithm stems from the ambition
to produce a series of these analog basebands, re-using the same
charging algorithm driver. No ASICs beside AB8500 and AB8505 were
ever produced so this terminology is confusing. Rename the
algorithm file and symbols to reflect the more narrow scope.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The kernel already has a static inline for linear interpolation
so use that instead of rolling our own.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to get the AB8500 charging driver working I ran into a bit
of bitrot: we haven't used the driver for a while so errors in
refactorings won't be noticed.
This one is pretty self evident: use argument to the macro or we
end up with a random pointer to something else.
Cc: stable@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Marcus Cooper <codekipper@gmail.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It turns out that the "T3 MRD" DMI_BOARD_NAME value is used in a lot of
different Cherry Trail x5-z8300 / x5-z8350 based Mini-PC / HDMI-stick
models from Ace PC / Meegopad / MinisForum / Wintel (and likely also
other vendors).
Most of the other DMI strings on these boxes unfortunately contain various
generic values like "Default string" or "$(DEFAULT_STRING)", so we cannot
match on them. These devices do have their chassis-type correctly set to a
value of "3" (desktop) which is a pleasant surprise, so also match on that.
This should avoid the quirk accidentally also getting applied to laptops /
tablets (which do actually have a battery). Although in my quite large
database of Bay and Cherry Trail based devices DMIdecode dumps I don't
have any laptops / tables with a board-name of "T3 MRD", so this should
not be an issue.
BugLink: https://askubuntu.com/questions/1206714/how-can-a-mini-pc-be-stopped-from-being-detected-as-a-laptop-with-a-battery/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in the updated "Naming" chapter of
Documentation/process/coding-style.rst, usage of the work blacklist
should be avoided where possible.
Rename the list of devices which have no battery to the
axp288_no_battery_list, which also more accurately describes the
contents of the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF):
drivers/power/supply/bq24190_charger.c:1972:34: warning: ‘bq24190_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids reimplementing the detection logic twice and removes the
possibility of activating charging with 500mA even if a battery is not
detected.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This invalidates empty->counter_uah and charge_full when charge_now
indicates that they are grossly wrong and adds some tolerance to
POWER_SUPPLY_PROP_CHARGE_FULL to allow for inaccuracies in the charge
counter and manufacturing tolerances in the battery.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow disabling and re-enabling battery charging of an axp209 PMIC
through a writable status property. With the current driver code
charging is always on.
This works on the axp209 of Banana {Pi M1+,Pro} and should work on all
AXP chips.
Signed-off-by: Hermann.Lauer@uni-heidelberg.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the driver with platform data (no board
files with the driver), so the dead code can be dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_ONLINE via platform data
functions or '1' if no platform data was provided. Since there are no
platforms using the driver with platform data (no board files with the
driver), the online property can be simplified to always return '1'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_STATUS via platform data
functions. Without platform data, the max17040_get_status() functions
returns early with POWER_SUPPLY_STATUS_UNKNOWN. Since there are no
platforms using the driver with platform data (no board files with the
driver), the status property was always unknown.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Iskren Chernev <iskren.chernev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ac->state field is __le32, not u32. So change the variable we're
temporarily storing it in to __le32 as well.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e61ffb3445 ("power: supply: Add AC driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently sbs-battery supports three string properties -
manufacturer, model_name, and chemistry. Buffers for those
properties are currently defined as global variables.
This patch moves those global variables into struct sbs_info
and cache/reuse them as they are all constant values.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds properties for setting the maximum current to USB, ADP and Battery
supplies. USB and ADP limits are reset to OTP values upon replugging.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The RC5T619 can detect SDP, CDP and DCP chargers, so let's add support
for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver is including the legacy GPIO header <linux/gpio.h>
but not using any symbols from it. Delete the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The result of container_of() operations is never NULL unless the element
is the first element of the embedded structure, which is not the case here.
The NULL check is therefore unnecessary and misleading. Remove it.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This setting is read directly from the device tree in
the ab8500_charger.c code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The vendor code tree supplies platform data to enable he
USB charging for AB8500 and AB8500 and disable the AC
charging on the AB8505. This was missed when the driver
was submitted to the mainline kernel.
Fix this by doing what the vendor kernel does: always
register the USB charger, do not register the AC charger
on the AB8505.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code was calling ab8500_bm_of_probe() in four different
spots effectively overwriting the same configuration three
times. This was done because probe order was uncertain.
Since we now used componentized probe, call it only once
while probing the main charging component.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver has problems with the different components of
the charging code racing with each other to probe().
This results in all four subdrivers populating battery
information to ascertain that it is populated for their
own needs for example.
Fix this by using component probing and thus expressing
to the kernel that these are dependent components.
The probes can happen in any order and will only acquire
resources such as state container, regulators and
interrupts and initialize the data structures, but no
execution happens until the .bind() callback is called.
The charging driver is the main component and binds
first, then bind in order the three subcomponents:
ab8500-fg, ab8500-btemp and ab8500-chargalg.
Do some housekeeping while we are moving the code around.
Like use devm_* for IRQs so as to cut down on some
boilerplate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery subsystem of the Surface Aggregator Module EC requires us to
register the battery notifier with instance ID 0. However, battery
events are actually sent with the instance ID corresponding to the
device, which is nonzero. Thus, the strict-matching approach doesn't
work here and will discard events that the driver is expected to handle.
To fix this we have to fall back on notifier matching by target-category
only and have to manually check the instance ID in the notifier
callback.
Fixes: 167f77f7d0 ("power: supply: Add battery driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
battery/charger driver changes:
* core: provide function stubs if CONFIG_POWER_SUPPLY=n
* core: reduce loglevel for probe defer info
* surface-battery: new battery driver for Surface
* surface-charger: new charger driver for Surface
* bq27xxx: add bq78z100 support
* bq27xxx: fix current_now/power_avg for newer chips
* cw2015: add CHARGE_NOW support
* ab8500: drop pdata support
* convert most DT bindings to YAML
* lot's of minor fixes and cleanups
reset drivers:
* ltc2952-poweroff: make trigger delay configurable from DT
* minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=9IUN
-----END PGP SIGNATURE-----
Merge tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"battery/charger driver changes:
- core:
- provide function stubs if CONFIG_POWER_SUPPLY=n
- reduce loglevel for probe defer info
- surface:
- new battery and charger drivers for Surface
- bq27xxx:
- add bq78z100 support
- fix current_now/power_avg for newer chips
- cw2015:
- add CHARGE_NOW support
- ab8500:
- drop pdata support
- convert most DT bindings to YAML
- lots of minor fixes and cleanups
reset drivers:
- ltc2952-poweroff:
- make trigger delay configurable from DT
- minor fixes and cleanups"
* tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (97 commits)
power: supply: cpcap-battery: fix invalid usage of list cursor
power: supply: bq256xx: add kerneldoc for structure members
power: supply: act8945a: correct kerneldoc
power: supply: max17040: remove unneeded double cast
power: supply: max17040: handle device_property_read_u8_array() failure
power: supply: max14577: remove unneeded variable initialization
power: supply: surface-charger: Make symbol 'surface_ac_pm_ops' static
power: supply: surface-battery: Make some symbols static
power: reset: restart-poweroff: Add missing MODULE_DEVICE_TABLE
power: reset: hisi-reboot: add missing MODULE_DEVICE_TABLE
power: supply: s3c_adc_battery: fix possible use-after-free in s3c_adc_bat_remove()
power: supply: generic-adc-battery: fix possible use-after-free in gab_remove()
power: supply: Add AC driver for Surface Aggregator Module
power: supply: Add battery driver for Surface Aggregator Module
power: supply: bq25980: Move props from battery node
power: supply: core: Use true and false for bool variable
power: supply: goldfish: Remove the GOLDFISH dependency
power: reset: ltc2952: make trigger delay configurable
power: supply: cpcap-charger: Simplify bool conversion
power: supply: cpcap-charger: Add usleep to cpcap charger to avoid usb plug bounce
...
Fix invalid usage of a list_for_each_entry in cpcap_battery_irq_thread().
Empty list or fully traversed list points to list head, which is not
NULL (and before the first element containing real data).
Signed-off-by: Guangqing Zhu <zhuguangqing83@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Document members of structure to fix W=1 warnings like:
drivers/power/supply/bq256xx_charger.c:240: warning:
Function parameter or member 'charger' not described in 'bq256xx_device'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove incorrect kerneldoc marker to fix W=1 warning:
drivers/power/supply/act8945a_charger.c:22: warning:
This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is no need for double explicit cast from of_device_get_match_data()
(uintptr_t and then to target enum) because implicit conversion from
uintptr_t to enum is straightforward (uintptr_t is a integer type).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The device_property_read_u8_array() call should not fail because it is
preceded with device_property_count_u8() and check for number of
readable u8 values. However the code is more obvious and easier to read
if the return value of device_property_read_u8_array() is checked.
Otherwise reader needs to investigate whether really there is no risk of
using random stack values of 'rcomp' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The local 'current_bits' variable does not have to be initialized
because all cases in following switch() either return or initialize it.
Addresses-Coverity: Unused value
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_charger.c:229:1: warning:
symbol 'surface_ac_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_charger.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_battery.c:700:1: warning:
symbol 'dev_attr_alarm' was not declared. Should it be static?
drivers/power/supply/surface_battery.c:805:1: warning:
symbol 'surface_battery_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_battery.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, AC status is also handled via SSAM,
an ACPI shim was present to translate the standard ACPI AC interface to
SSAM requests. The SSAM interface itself, which is modeled closely after
the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support AC
status/information via the aforementioned interface on said Surface
models.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, battery status is also handled via
SSAM, an ACPI shim was present to translate the standard ACPI battery
interface to SSAM requests. The SSAM interface itself, which is modeled
closely after the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support
battery status/information via the aforementioned interface on said
Surface models. It is in parts based on the standard ACPI battery
driver.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT and
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE are exposed on
the battery node and this is incorrect.
This patch exposes both of them on the charger node rather
than the battery node.
Fixes: 5069185fc1 ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-power-v5.13' into psy-next
Immutable branch between MFD and Power due for the v5.13 merge window.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This will allow to use the BATTERY_GOLDFISH driver
without enabling GOLDFISH.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make trigger delay configurable through device tree with
trigger-delay-ms property.
Trigger delay is the time to wait before starting shutdown
sequence after trigger line assertion.
Trigger delay must take into account the OFFT time configured
with the capacitor connected to OFFT pin of the LTC2952 chip.
Basically, the higher the capacitance connected to OFFT pin,
the larger trigger delay must be.
Signed-off-by: Marek Czerski <ma.czerski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Linus Torvalds