This patch fixes WARNING:MISSING_BREAK found with checkpatch check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:ASSIGN_IN_IF found with checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:NETWORKING_BLOCK_COMMENT_STYLE from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:TRAILING_STATEMENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:POINTER_LOCATION from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'frequency' indicates the embedded cpu's frequency, but that
should not be necessary for any purpose.
'txpending' is an attribute for debugging.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netdev->dev_id obsoletes this property.
None of the remaining properties contribute to udev detection methods.
The regular calls for the sysfs group can thus safely be restored.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add two new USB devices supported by the driver and fix bad
english.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the Kvaser Leaf v2 and Leaf usb mini
PCIe card.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some Kvaser hardware, the firmware returns extra messages after the
request for card info. For instance on a Leaf Light v2:
--> CMD_GET_CARD_INFO
<-- CMD_USB_THROTTLE
<-- CMD_GET_CARD_INFO2
<-- CMD_GET_CARD_INFO_REQ
When it happens, the probing function fails because we only read
the first usb message.
To overcome this issue, we add a mechanism of retries to the
kvaser_usb_wait_msg() function.
I tested this patch with the following hardware:
- Kvaser Leaf Light
- Kvaser Leaf Light v2
- Kvaser USBCan R
This patch is necessary for the Leaf Light v2 hardware.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create a directory for all CAN drivers using SPI and move mcp251x driver there.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds check for mcp251x_hw_reset() result on startup and
removes unnecessary checking for CANSTAT register since this value
is being checked in mcp251x_hw_reset().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MCP251x utilizes an oscillator startup timer (OST), which holds the
chip in reset, to insure that the oscillator has stabilized before the
internal state machine begins to operate. The OST maintains reset for
the first 128 OSC clock cycles after power up or reset.
So, this patch removes unnecessary loops and reduce delay for power on
and reset to the safe value.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves setup of SPI bus a bit earlier and adds check for spi_setup()
result to be sure SPI bus is communicating with the device properly.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch allows to switch the netns when packet is encapsulated or
decapsulated.
The vxlan socket is openned into the i/o netns, ie into the netns where
encapsulated packets are received. The socket lookup is done into this netns to
find the corresponding vxlan tunnel. After decapsulation, the packet is
injecting into the corresponding interface which may stand to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Configuration example:
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
ip link set vxlan10 netns netns1
ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10
ip netns exec netns1 ip link set vxlan10 up
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine some macros that were conditioned upon SMC_DEBUG level.
By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.
Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.
The default value of the parameter is set to "1" mimicing the earlier
behavior.
Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -
netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920
Transactions per second:
Before change: 1,367.11
After change: 1,470.65
Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.
Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).
Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separating the actual xmit part from the function in a separate
function that can be used in the tlb_xmit in the next patch. Also
there is no reason do_tx_balance to be an int so changing it to
bool type.
Change-Id: I9c48ff30487810f68587e621a191db616f49bd3b
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified the hash function to return just hash separating from the
modulo operation that can be performed by the caller. This is to
make way for the tlb mode to use the same hashing policies that
are used in the 802.3ad and Xor mode.
Change-Id: I276609e87e0ca213c4d1b17b79c5e0b0f3d0dd6f
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe, ixgbevf, e1000e, igb and i40e.
Jacob converts the ixgbe low_water into an array which allows the
algorithm to output different values for different TCs and we can
distinguish between them. Removes vlan_filter_disable() and
vlan_filter_enable() in ixgbe so that we can do the work directly in
set_rx_mode(). Changes the setting of multicast filters only when
the interface is not in promiscuous mode for multicast packets in
ixgbe. Improves MAC filter handling by adding mac_table API based
on work done for igb, which includes functions to add/delete MAC
filters.
Mark changes register reads in ixgbe to an out-of-line function since
register reads are slow.
Emil provides a ixgbevf patch to update the driver description since
it supports more than just 82599 parts now.
David provides several cleanup patches for e1000e which resolve some
checkpatch issues as well as changing occurrences of returning 0 or 1 in
bool functions to returning true false or true.
Carolyn provides several cleanup patches for igb which fix checkpatch
warnings.
Mitch provides a fix for i40evf where the driver would correctly allow
the virtual function link state to be controlled by 'ip set link', but
would not report it correctly back. This is fixed by filling out
the appropriate field in the VF info struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic data structures instead of struct pci_dev wherever
possible in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove legacy PCI DMA wrappers and instead use generic DMA functions
directly in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.
Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that moved broadcasts to process context added
a couple of bugs on the error path where we may dereference NULL
or leak an skb. This patch fixes them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The union contains only one member now, so we use the variables in it directly.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed recv_pkt_list and lock, and updated related code, so that
the locking overhead is reduced especially when multiple channels
are in use.
The recv_pkt_list isn't actually necessary because the packets are
processed sequentially in each channel. It has been replaced by a
local variable, and the related lock for this list is also removed.
The is_data_pkt field is not used in receive path, so its assignment
is cleaned up.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the driver would correctly allow the VF link state to be
controlled by 'ip set link', it would not report it correctly back.
Fix this by filling out the appropriate field in the vf info struct.
Change-ID: I58d8e356438190e1ee9660b424301af6f416cdbe
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:BRACES and ERROR:OPEN_BRACE from
checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:PREFER_PR_LEVEL and WARNING:SPLIT_STRING
from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixing "WARNING:SPACING: Unnecessary space before function pointer arguments"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixing "WARNING:SPACING: networking uses a blank line after declarations"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing occurrences of returning 0 and 1 from bool functions to false and
true, respectively
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes 82599 from the description of the ixgbevf module
since the VF driver is supported on other parts as well.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mac_table API based on work done for igb, which includes functions
to add and delete mac filters. This simplifies code for various entities
that use MAC filters such as VMDQ, SR-IOV, MACVLAN, and such.
Reported-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In line with changes done by Alex Duyck regarding unicast filters, we
now only set multicast filters when the interface is not in promiscuous
mode for multicast packets. This also has an impact on the RAR usage
such that SR-IOV has some RARs reserved for its own usage.
Reported-by: Alex Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously these functions handled stripping setup as well, but this has
already been removed from these functions. Rather than encapsulating
this into a function, we can just do the work directly in set_rx_mode.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register reads are slow, so don't inline them.
Size before:
text data bss dec hex filename
226337 8280 552 235169 396a1 ixgbe.ko
Size after:
text data bss dec hex filename
194578 8280 552 203410 31a92 ixgbe.ko
for about a 14% reduction in text size.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since fc.high_water is an array, we should treat low_water as an array
also. This allows the algorithm to output different values for different
TCs, and then we can distinguish between them. In addition, this patch
changes one path that didn't honor the return value from ixgbe_setup_fc.
Reported-by: Aaron Salter <aaron.k.salter@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Greg provides two patches for i40e, the first adds the netdev ops to support
the addition of static FDB entries in the physical function (PF) MAC/VLAN
filter table so that the virtual functions (VFs) can communicate with
bridged virtual Ethernet ports such as those provided by the virtio
driver. The second is to fix an issue where the assignment of a port
VLAN after it is already up and running requires the VF driver to be
reloaded, so print a message warning the host administrator about the
need to reload the VF driver. In addition, knock the VF offline so that
it does not continue to receive traffic not on the port VLAN assigned to
it.
Jesse provides a patch for i40e and i40evf to unhide and enable the
PREFENA field in the receive host memory cache (RX-HMC) for best
performance.
Mitch provides a i40e patch to implement the net device op for Tx
bandwidth setting.
Catherine removes a firmware workaround that is no longer needed with
the latest firmware for i40e. She also provides some minor cleanups
as well bumps the driver versions.
Anjali provides a fix for i40e displaying IPv4 flow director filters
which needed additional information to be communicated up above in
order for it to be displayed correctly.
Shannon adds tracking of the NVM busy state so that the driver won't
allow a new NVM update command until a completion event is received
from the current update. Updates the admin queue API to reflect
recent changes in the firmware. Also rearranges the "if netdev" logic
to prepare for handling non-netdev VSIs. Lastly rework the fdir
setup and tear down to use the newly created i40e_vsi_open() and
i40e_vsi_close(), which also fixes a memory leak of the FDIR queue
buffer info structs across a reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SMC_DEBUG >= 2, we hit the following compilation error:
drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy_found error path when there is no phy device
and changes bus_name.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves cksum_ctl to tx_rd_des23 from cksum_pktlen for correct checksum
offloading and modifies size for Tx/Rx descriptor.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Execute "ethtool -L eth0 combined 0" in guest, if multiqueue
is enabled, virtnet_send_command() will return -EINVAL error,
there is a validation in QEMU.
But if multiqueue is disabled, virtnet_set_queues() will just
return zero (success). We should return error for this situation.
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.
Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step to remove leftover code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've implemented table calculation, but forgot to enable writing it in
power setup function.
By the way document table layout.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logic in specs and our code was wrong. Init and calibration values for
newer cards depend on radio revision, not PHY revision.
To make code clearer, change tables names to include "radio" or "phy".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were extracted from MMIO dumps of 14e4:4353 and wl 6.30.223.141.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 0x200 has been noticed in the following log:
radio_read(0x02ca) -> 0x0000
radio_write(0x00ca) <- 0x0080
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New Broadcom drivers don't upload it anymore. It was probably a copy & paste
mistake in early N-PHY rev 3+ days.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After changing local per interface beacon setting restore original
global beaconing state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.
These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.
We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command nodes are increased from 20 to 50. Now we can always
scan 1 channel per scan command to avoid traffic delay/loss in
connected state. We will get rid of *CHANNEL_PER_SCAN_CMD macros
used due to command node constraints.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCIe, aggregate more AMSDU packets till PCIe TXBD is full.
For SDIO, aggregation was disabled for AMSDU packets because
AMSDU aggregated packet size is already 4K or 8K, SDIO Multiport
Aggregation feature didn't use to gain much previously.
Now with increased multiport aggregation buffer, we can enable
it for AMSDU packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: single byte memset is suspicious.
Swapped 2nd/3rd argument?
This code happens to work because rx_mcs is the first variable
in mcs structure. We should use 'mcs.rx_mcs' here anyway.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW should never attempt to perform DMA for unused queues.
For rtl8187se this is ensured by setting a dedicated register at
init time, before enabling TX.
In rtl8180/5 the register is only written at the first TX (because
in rtl8180/5 it serves also to kick DMA for used queues).
This should be enough, but it's worth to add a register write at
init time, before enabling TX.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parentheses are missing around the macro argument, causing the
macro possibly not to work passing certain expressions as
arguments.
This should not cause any issues with current code, however it's
worth to add them, as a good practice, and to eventually avoid
future bugs.
Suggested-by: Dave Kilroy <kilroyd@googlemail.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When preparing the bitfield to write to HW register, the high-priority
queue error interrupt bit is set two times, and the beacon queue
TX-OK interrupt is not enabled.
Currently this have no functional impact because the high-priority
queue is not used at all, and the beacon queue is not used yet.
This patch removes high-priority queue bits and it adds the
beacon queue missing bit.
It removes also the management queue bits because it is not used.
This was found by static code analyzer.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8180 driver can handle also rtl8185 and rtl8187SE cards,
however in userspace tools (network manager) it still appares
as "rtl8180".
This might lead the user to think the wrong driver is in use.
This patch changes module name to "rtl818x_pci" that should be
more explanatory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> [ original patch ]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump i40e to version 0.3.43 and i40evf to version 0.9.21.
Change-ID: Ice4c715731bfa1dfc12dd45418675a3ba6e08d57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tweak a for-loop to make it easier to add conditional stats in the future.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the newer i40e_vsi_open() and i40e_vsi_close() in the FDIR VSI
lifetime. This makes sure we're using standard methods for all the
VSI open and close paths. This also fixes a memory leak of the
FDIR queue buffer info structs across a reset.
Change-ID: I1b60a1b08ab923afe4f49810c2c7844d850e19b9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new i40e_vsi_open() for waking VSIs back up in order to
be sure all the standard actions happen.
Change-ID: Ic3479410dd3079733f4951dcea69f101e69e77df
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Abstract out the vsi close actions into a single function so they
can be used correctly for both netdev and non-netdev based VSIs.
Change-ID: I59e3d115fcb20e614a09477281b7787dd340d276
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM updates take some time and are asynchronous actions that signal
their completion with an AdminQ event. This code tracks when there is
an NVM update outstanding and won't allow a new update command until a
completion event is received from the current update.
Change-ID: Ic132fe16bd9dc09b002ed38297a877c1a01553ce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flow spec coming in for IPv4 filters is IP_USER_FLOW, which
needed some more info to be communicated up above in order for it
to be displayed correctly.
Change-ID: Ia968238e0d7c4c4df12908ba81f0c4501280f3ec
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the FW workaround to increment the number of msix vectors.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the net device op for Tx bandwidth setting. Setting the Tx
bandwidth is done by 'ip link set <PF device> vf <VF num> rate <Tx
rate>', with the rate specified in Mbit/sec. The rate setting is
displayed with 'ip link show'.
Change-ID: I4d45dda8320632fdb6ec92c87d083e51070b46ab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a host VMM administrator hoses his VF by assigning a port VLAN after
it is already up and running with implicit permission to set local
VLANs then we print a message warning the host administrator that the
VF driver needs to be reloaded.
In addition we need to knock the VF offline so that it does not continue
to receive traffic not on the port VLAN assigned to it. So we reset the
VF. The VF will cease operation and the administrator will be forced to
unload and reload the VF driver to make it work again.
Change-ID: Iae1ae006b244e74e30a4ee546b3c5fca5cfb40aa
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PREFENA field in the receive host memory cache (RX-HMC)
must be visible in order to be set to 1 at driver init for
best performance.
Change-ID: I16b0bcd84cf56f4b6c938201ff5e954bee5a1992
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the netdev ops to support addition of static FDB entries in the
physical function (PF) MAC/VLAN filter table so that virtual functions
(VFs) can communicate with bridged virtual Ethernet ports such as those
provided by the virtio driver.
Change-ID: Ifbd6817a75074e3b5cdf945a5635f26440bf15df
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sxgbe_config() denies changing the base address and interrupt, and
ignores all other 'struct ifmap' members, which means that it is useless
as is, so let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_config() returns -ENOSYS and does not implement anything useful,
let's remove it such that net/core/dev_ioctl.c::dev_ifsioc can return
something meaningful like -EOPNOTSUPP.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows multiple channels to be used by each virtual NIC.
It is available on Hyper-V host 2012 R2.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently broadcasts are handled in network RX context, where
the packets are sent through netif_rx. This means that the number
of macvlans will be constrained by the capacity of netif_rx.
For example, setting up 4096 macvlans practically causes all
broadcast packets to be dropped as the default netif_rx queue
size simply can't handle 4096 skbs being stuffed into it all
at once.
Fundamentally, we need to ensure that the amount of work handled
in each netif_rx backlog run is constrained. As broadcasts are
anything but constrained, it either needs to be limited per run
or moved to process context.
This patch picks the second option and moves all broadcast handling
bar the trivial case of packets going to a single interface into
a work queue. Obviously there also needs to be a limit on how
many broadcast packets we postpone in this way. I've arbitrarily
chosen tx_queue_len of the master device as the limit (act_mirred
also happens to use this parameter in a similar way).
In order to ensure we don't exceed the backlog queue we will use
netif_rx_ni instead of netif_rx for broadcast packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Time stamping resources are per-interface so there is no need
to keep separate last_rx_timestamp for each Rx ring, move
last_rx_timestamp to the adapter structure.
With last_rx_timestamp inside adapter, ixgbe_ptp_rx_hwtstamp()
inline function is reduced to a single if statement so it is
no longer necessary. If statement is placed directly in
ixgbe_process_skb_fields() fixing likely/unlikely marking.
Checks for q_vector or adapter to be NULL are superfluous.
Comment about taking I/O hit is a leftover from previous design.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RQDPC on i210/i211 is R/W not ReadClear. Clear after reading.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
static int e1000e_pm_thaw(struct device *dev)
^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN. Later tests in the driver
set the rx_buffer_len based on the mtu. As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.
Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the i40e driver was allowing the hardware
to replicate the PSH flag on all segments of a TSO operation.
This patch fixes the first/middle/last TCP flags settings which
makes the TSO operations work correctly.
With this change we are now configuring the CWR bit to only be set
in the first packet of a TSO, so this patch also enables TSO_ECN,
in order to advertise to the stack that we do the right thing
on the wire.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
pull request: wireless 2014-04-17
Please pull this batch of fixes intended for the 3.15 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Chun-Yeow to not look at management frame bitrates
that are typically really low, two fixes from Felix for AP_VLAN
interfaces, a fix from Ido to disable SMPS settings when a monitor
interface is enabled, a radar detection fix from Michał and a fix from
myself for a very old remain-on-channel bug."
For the iwlwifi bits, Emmanuel says:
"I have new device IDs and a new firmware API. These are the trivial
ones. The less trivial ones are Johannes's fix that delays the
enablement of an interrupt coalescing hardware until after association
- this fixes a few connection problems seen in the field. Eyal has a
bunch of rate control fixes. I decided to add these for 3.15 because
they fix some disconnection and packet loss scenarios which were
reported by the field. I also have a fix for a memory leak that
happens only with a very new NIC."
Along with those...
Amitkumar Karwar fixes a couple of problems relating to driver/firmware
interactions in mwifiex.
Christian Engelmayer avoids a couple of potential memory leaks in
the new rsi driver.
Eliad Peller provides a wl18xx mailbox alignment fix for problems
when using new firmware.
Frederic Danis adds a couple of missing debugging strings to the
cw1200 driver.
Geert Uytterhoeven adds a variable initialization inside of the
rsi driver.
Luciano Coelho patches the wlcore code to ignore dummy packet events
in PLT mode in order to work around a firmware bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error path and deinit/removal functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver is triggering schedules while atomic inside
mlx4_en_netpoll:
spin_lock_irqsave(&cq->lock, flags);
napi_synchronize(&cq->napi);
^^^^^ msleep here
mlx4_en_process_rx_cq(dev, cq, 0);
spin_unlock_irqrestore(&cq->lock, flags);
This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.
In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.
Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:
- QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured in QSGMII. Technically speaking,
configuring the SERDES of the first port would be sufficient, but
it is simpler to do it on all ports.
- SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured as SGMII.
- RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
cleared, and no SERDES configuration is done, because RGMII is not
using SERDES lanes.
- other: an error is returned. For this reason, the
mvneta_port_power_up() now returns an int instead of nothing, and
the return value is checked by mvneta_probe().
This has been successfully tested on:
* Armada XP DB, which has two RGMII and two SGMII connections
* Armada XP GP, which uses QSGMII for its four interfaces
* Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when command timeout occurs due to a firmware or
hardware bug, there may be some synchronous commands in command
queue. These commands are never downloaded to firmware causing
hung task warnings. This patch replaces wait_event_interruptible
call with wait_event_interruptible_timeout to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During extended scan, SCAN report event is always followed by
command response. Sometimes It is observed that command response
is processed before SCAN report which leads to a crash, because
current command node is cleared while handling the response.
This patch makes sure that driver's main thread gives priority
to events over command responses.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In cosa driver, udelay with more than 20000 may cause __bad_udelay.
Use msleep for instead.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __at86rf230_read_subreg function don't mask and shift register
contents which it should do. This patch adds the necessary masks and
shift operations in this function.
Since we have csma support this can make some trouble on state changes.
Since CSMA support turned on some bits in the TRX_STATUS register that
used to be zero, not masking broke checking of the TRX_STATUS field
after commanding a state change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVDD regulator is only enabled when the RF section is active TX_ON
(PLL_ON) state. Since commit 7dcbd22a97
("ieee802154: ensure that first RF212 state comes from TRX_OFF").
We are in TRX_OFF state at the time at86rf230_hw_init is run.
Note that this test would only fail in case of a severe hardware
malfunction (faulty/shorted power supply, etc.) so it wasn't all that
useful in the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cadence ethernet chipsets are only used on specific ARM
architectures. Add Kconfig dependencies so that drivers for these
chipsets are only buildable on the relevant architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware needs the local device mac address to support hw loopback for
rdma loopback connections.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields are missing from the event mailbox
struct definitions, which cause issues when
trying to handle some events.
Add the missing fields in order to align the
struct size (without adding actual support
for the new fields).
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes: 028e724 ("wl18xx: move to new firmware (wl18xx-fw-3.bin)")
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential memory leak in the error path of function
rsi_send_auto_rate_request(). In case memory allocation for array
'selected_rates' fails, the error path exits and leaves the previously
allocated skb in place. Detected by Coverity: CID 1195575.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This array is used in debug string to display cw1200_link_status
defined in drivers/net/wireless/cw1200/cw1200.h.
Add missing strings for CW1200_LINK_RESET and CW1200_LINK_RESET_REMAP.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>