Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Cc: stable@vger.kernel.org
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.
Also changed &bssid to bssid, at the suggestion of Stanislav Yakovlev.
The semantic match that finds the first problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@
*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.
We also remove old rules to that matches product id for Broadcom devices.
Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This return holds the number of bytes transfered (1 byte) or a negative
error code. The type should be int instead of u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b74713d04e
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.
Fix this by disabling IRQs in the handler without touching intr_ref_cnt.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.
Disable greenfield for now to prevent that problem.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not pass NULL libconf->conf->channel to rt61pci_config() as it
is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=44361
Cc: stable@vger.kernel.org
Reported-and-tested-by: <dolohow@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.
Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if_sdio_card structure was never being freed, and neither
was the command structure used for association.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is going to fix the resuming failed from S3/S4
for rt3290 chip.
Signed-off-by: Woody Hung <Woody.Hung@mediatek.com>
Cc: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On an OLPC XO-1.5 we have seen the following situation:
- the system starts going into suspend
- no wake params are set, so the mmc layer removes the card
- during remove, we send a command to the card
- that command fails, causing if_sdio's reset method to try and remove
the mmc card in attempt to reset it
- the mmc layer is not happy about being asked to remove a card that
it is already removing, and the kernel crashes
While the MMC layer could possibly be taught to behave better here,
it also seems sensible for libertas not to try and reset a card if
we're in the process of removing it anyway.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In bnx2x_mcast_enqueue_cmd() we'll leak the memory allocated to
'new_cmd' if we hit the deafault case of the 'switch (cmd)'.
Add a 'kfree(new_cmd)' to that case to avoid the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently an skb requiring TSO may not fit within a minimum-size TX
queue. The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset). This issue is designated as CVE-2012-3412.
Set the maximum number of TSO segments for our devices to 100. This
should make no difference to behaviour unless the actual MSS is less
than about 700. Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.
To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
It includes:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJQGSWqAAoJECSVL5KnPj1PnEQP/RQ5NWKlgkPloLkWrLc8stN/
0AKWgxBJ0BuJBW6CJCKVy76kkCBW2PZ7bHsFLNuX490KnPwt1cz3sLni78UiW1CZ
bNlN5UKshOfC511BxF5GZjtLvvkj5+ocmoybq27MhBoJn/7EVbli7lSeYjEWeWuk
sTq6wJTBJ8Nc4PEWdPhIbiWe7NgnCge27AOHrzUV5cRHxdHtl+mqD99Ky7UdMsHz
qBVTVmtEmLh2g3KMuu5rByuDDlUqhpi0sKorGsNWk92rpUnVsc4E4/v06JJqB3n8
ef3q352GK32LKpWwX78pm5+DJMhpSMFJg6UrvQu03gQSU5Pw3O4Dl8g+hh6FgcMo
niYZ+g07K0D8BSqdTwy9gwRTSWLPHplR8xz9VsW3+jdmFFuQgB6suA2Dk2E/K3Cf
12jurwegypfI5KutRyTz7IuTw/8OhHs4x0PJWcSw3lq1czUM212vqDWKYJFbgznq
6s8sHLWnQg0U47LYTCNV/mA4QRlE4ewE3B6wIVrzPvcTIinKqO1hky10fZ4+sEw6
gH6bnSBvlRgYOYhy/MPInz0Gt6YfzK26M6ZPMq2DU7gZ6OFcL9IrnqWDdnZMwwD9
j15DWeU2XPMc8vAGpdg2giq3VmQ53rviwLgp7Ht6fGrTLk1z4q167zGUSOvo3KQi
Ai90ycCBgAGLorHhdCI1
=22b7
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
* tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6: (78 commits)
da8xx-fb: fix compile issue due to missing include
fbdev: Make pixel_to_pat() failure mode more friendly
da8xx-fb: do not turn ON LCD backlight unless LCDC is enabled
fbdev: sh_mobile_lcdc: Fix vertical panning step
video: exynos mipi dsi: Fix mipi dsi regulators handling issue
video: da8xx-fb: do clock reset of revision 2 LCDC before enabling
arm: da850: configure LCDC fifo threshold
video: da8xx-fb: configure FIFO threshold to reduce underflow errors
video: da8xx-fb: fix flicker due to 1 frame delay in updated frame
video: da8xx-fb rev2: fix disabling of palette completion interrupt
da8xx-fb: add missing FB_BLANK operations
video: exynos_dp: use usleep_range instead of delay
video: exynos_dp: check the only INTERLANE_ALIGN_DONE bit during Link Training
fb: epson1355fb: Fix section mismatch
video: exynos_dp: fix wrong DPCD address during Link Training
video/smscufx: fix line counting in fb_write
aty128fb: Fix coding style issues
fbdev: sh_mobile_lcdc: Fix pan offset computation in YUV mode
fbdev: sh_mobile_lcdc: Fix overlay registers update during pan operation
fbdev: sh_mobile_lcdc: Support horizontal panning
...
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
Pull core block IO bits from Jens Axboe:
"The most complicated part if this is the request allocation rework by
Tejun, which has been queued up for a long time and has been in
for-next ditto as well.
There are a few commits from yesterday and today, mostly trivial and
obvious fixes. So I'm pretty confident that it is sound. It's also
smaller than usual."
* 'for-3.6/core' of git://git.kernel.dk/linux-block:
block: remove dead func declaration
block: add partition resize function to blkpg ioctl
block: uninitialized ioc->nr_tasks triggers WARN_ON
block: do not artificially constrain max_sectors for stacking drivers
blkcg: implement per-blkg request allocation
block: prepare for multiple request_lists
block: add q->nr_rqs[] and move q->rq.elvpriv to q->nr_rqs_elvpriv
blkcg: inline bio_blkcg() and friends
block: allocate io_context upfront
block: refactor get_request[_wait]()
block: drop custom queue draining used by scsi_transport_{iscsi|fc}
mempool: add @gfp_mask to mempool_create_node()
blkcg: make root blkcg allocation use %GFP_KERNEL
blkcg: __blkg_lookup_create() doesn't need radix preload
Pull md updates from NeilBrown.
* 'for-next' of git://neil.brown.name/md:
DM RAID: Add support for MD RAID10
md/RAID1: Add missing case for attempting to repair known bad blocks.
md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE.
md/raid1: don't abort a resync on the first badblock.
md: remove duplicated test on ->openers when calling do_md_stop()
raid5: Add R5_ReadNoMerge flag which prevent bio from merging at block layer
md/raid1: prevent merging too large request
md/raid1: read balance chooses idlest disk for SSD
md/raid1: make sequential read detection per disk based
MD RAID10: Export md_raid10_congested
MD: Move macros from raid1*.h to raid1*.c
MD RAID1: rename mirror_info structure
MD RAID10: rename mirror_info structure
MD RAID10: Fix compiler warning.
raid5: add a per-stripe lock
raid5: remove unnecessary bitmap write optimization
raid5: lockless access raid5 overrided bi_phys_segments
raid5: reduce chance release_stripe() taking device_lock
* set_fs(KERNEL_DS) + getname() is probably the weirdest implementation
of strdup() I've seen. Especially since they don't to copy it at all...
* filp_open() never returns NULL; it's ERR_PTR(-E...) on failure.
* file->f_dentry is never going to be NULL, TYVM.
* match_strdup() + snprintf() + kfree() is a bloody weird way to spell
match_strlcpy().
Pox on cargo-cult programmers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fx5A
-----END PGP SIGNATURE-----
Merge tag 'vfio-for-v3.6' of git://github.com/awilliam/linux-vfio
Pull VFIO core from Alex Williamson:
"This series includes the VFIO userspace driver interface for the 3.6
kernel merge window. This driver is intended to provide a secure
interface for device access using IOMMU protection for applications
like assignment of physical devices to virtual machines.
Qemu will be the first user of this interface, enabling assignment of
PCI devices to Qemu guests. This interface is intended to eventually
replace the x86-specific assignment mechanism currently available in
KVM.
This interface has the advantage of being more secure, by working with
IOMMU groups to ensure device isolation and providing it's own
filtered resource access mechanism, and also more flexible, in not
being x86 or KVM specific (extensions to enable POWER are already
working).
This driver is originally the work of Tom Lyon, but has since been
handed over to me and gone through a complete overhaul thanks to the
input from David Gibson, Ben Herrenschmidt, Chris Wright, Joerg
Roedel, and others. This driver has been available in linux-next for
the last month."
Paul Mackerras says:
"I would be glad to see it go in since we want to use it with KVM on
PowerPC. If possible we'd like the PowerPC bits for it to go in as
well."
* tag 'vfio-for-v3.6' of git://github.com/awilliam/linux-vfio:
vfio: Add PCI device driver
vfio: Type1 IOMMU implementation
vfio: Add documentation
vfio: VFIO core
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
- Fix IPoIB to stop using unsafe linkage between networking neighbour
layer and private path database.
- Small fixes for bugs found by Fengguang Wu's automated builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zFTH
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull final RDMA changes from Roland Dreier:
- Fix IPoIB to stop using unsafe linkage between networking neighbour
layer and private path database.
- Small fixes for bugs found by Fengguang Wu's automated builds.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Use a private hash table for path lookup in xmit path
IB/qib: Fix size of cc_supported_table_entries
RDMA/ucma: Convert open-coded equivalent to memdup_user()
RDMA/ocrdma: Fix check of GSI CQs
RDMA/cma: Use PTR_RET rather than if (IS_ERR(...)) + PTR_ERR
Pull second set of media updates from Mauro Carvalho Chehab:
- radio API: add support to work with radio frequency bands
- new AM/FM radio drivers: radio-shark, radio-shark2
- new Remote Controller USB driver: iguanair
- conversion of several drivers to the v4l2 core control framework
- new board additions at existing drivers
- the remaining (and vast majority of the patches) are due to
drivers/DocBook fixes/cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (154 commits)
[media] radio-tea5777: use library for 64bits div
[media] tlg2300: Declare MODULE_FIRMWARE usage
[media] lgs8gxx: Declare MODULE_FIRMWARE usage
[media] xc5000: Add MODULE_FIRMWARE statements
[media] s2255drv: Add MODULE_FIRMWARE statement
[media] dib8000: move dereference after check for NULL
[media] Documentation: Update cardlists
[media] bttv: add support for Aposonic W-DVR
[media] cx25821: Remove bad strcpy to read-only char*
[media] pms.c: remove duplicated include
[media] smiapp-core.c: remove duplicated include
[media] via-camera: pass correct format settings to sensor
[media] rtl2832.c: minor cleanup
[media] Add support for the IguanaWorks USB IR Transceiver
[media] Minor cleanups for MCE USB
[media] drivers/media/dvb/siano/smscoreapi.c: use list_for_each_entry
[media] Use a named union in struct v4l2_ioctl_info
[media] mceusb: Add Twisted Melon USB IDs
[media] staging/media/solo6x10: use module_pci_driver macro
[media] staging/media/dt3155v4l: use module_pci_driver macro
...
Conflicts:
Documentation/feature-removal-schedule.txt
Pull networking update from David S. Miller:
"I think Eric Dumazet and I have dealt with all of the known routing
cache removal fallout. Some other minor fixes all around.
1) Fix RCU of cached routes, particular of output routes which require
liberation via call_rcu() instead of call_rcu_bh(). From Eric
Dumazet.
2) Make sure we purge net device references in cached routes properly.
3) TG3 driver bug fixes from Michael Chan.
4) Fix reported 'expires' value in ipv6 routes, from Li Wei.
5) TUN driver ioctl leaks kernel bytes to userspace, from Mathias
Krause."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
ipv4: Properly purge netdev references on uncached routes.
ipv4: Cache routes in nexthop exception entries.
ipv4: percpu nh_rth_output cache
ipv4: Restore old dst_free() behavior.
bridge: make port attributes const
ipv4: remove rt_cache_rebuild_count
net: ipv4: fix RCU races on dst refcounts
net: TCP early demux cleanup
tun: Fix formatting.
net/tun: fix ioctl() based info leaks
tg3: Update version to 3.124
tg3: Fix race condition in tg3_get_stats64()
tg3: Add New 5719 Read DMA workaround
tg3: Fix Read DMA workaround for 5719 A0.
tg3: Request APE_LOCK_PHY before PHY access
ipv6: fix incorrect route 'expires' value passed to userspace
mISDN: Bugfix only few bytes are transfered on a connection
seeq: use PTR_RET at init_module of driver
bnx2x: remove cast around the kmalloc in bnx2x_prev_mark_path
ipv4: clean up put_child
...
Felix Fietkau