syzkaller found a race condition fanout_demux_rollover() while removing
a packet socket from a fanout group.
po->rollover is read and operated on during packet_rcv_fanout(), via
fanout_demux_rollover(), but the pointer is currently cleared before the
synchronization in packet_release(). It is safer to delay the cleanup
until after synchronize_net() has been called, ensuring all calls to
packet_rcv_fanout() for this socket have finished.
To further simplify synchronization around the rollover structure, set
po->rollover in fanout_add() only if there are no errors. This removes
the need for rcu in the struct and in the call to
packet_getsockopt(..., PACKET_ROLLOVER_STATS, ...).
Crashing stack trace:
fanout_demux_rollover+0xb6/0x4d0 net/packet/af_packet.c:1392
packet_rcv_fanout+0x649/0x7c8 net/packet/af_packet.c:1487
dev_queue_xmit_nit+0x835/0xc10 net/core/dev.c:1953
xmit_one net/core/dev.c:2975 [inline]
dev_hard_start_xmit+0x16b/0xac0 net/core/dev.c:2995
__dev_queue_xmit+0x17a4/0x2050 net/core/dev.c:3476
dev_queue_xmit+0x17/0x20 net/core/dev.c:3509
neigh_connected_output+0x489/0x720 net/core/neighbour.c:1379
neigh_output include/net/neighbour.h:482 [inline]
ip6_finish_output2+0xad1/0x22a0 net/ipv6/ip6_output.c:120
ip6_finish_output+0x2f9/0x920 net/ipv6/ip6_output.c:146
NF_HOOK_COND include/linux/netfilter.h:239 [inline]
ip6_output+0x1f4/0x850 net/ipv6/ip6_output.c:163
dst_output include/net/dst.h:459 [inline]
NF_HOOK.constprop.35+0xff/0x630 include/linux/netfilter.h:250
mld_sendpack+0x6a8/0xcc0 net/ipv6/mcast.c:1660
mld_send_initial_cr.part.24+0x103/0x150 net/ipv6/mcast.c:2072
mld_send_initial_cr net/ipv6/mcast.c:2056 [inline]
ipv6_mc_dad_complete+0x99/0x130 net/ipv6/mcast.c:2079
addrconf_dad_completed+0x595/0x970 net/ipv6/addrconf.c:4039
addrconf_dad_work+0xac9/0x1160 net/ipv6/addrconf.c:3971
process_one_work+0xbf0/0x1bc0 kernel/workqueue.c:2113
worker_thread+0x223/0x1990 kernel/workqueue.c:2247
kthread+0x35e/0x430 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:432
Fixes: 0648ab70af ("packet: rollover prepare: per-socket state")
Fixes: 509c7a1ecc ("packet: avoid panic in packet_getsockopt()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Mike Maloney <maloney@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: fix some other sparse errors
After the last fixes for sparse errors, there are still three sparse
errors in sctp codes, two of them are type cast, and the other one
is using extern.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now each stream sched ops is defined in different .c file and
added into the global ops in another .c file, it uses extern
to make this work.
However extern is not good coding style to get them in and
even make C=2 reports errors for this.
This patch adds sctp_sched_ops_xxx_init for each stream sched
ops in their .c file, then get them into the global ops by
calling them when initializing sctp module.
Fixes: 637784ade2 ("sctp: introduce priority based stream scheduler")
Fixes: ac1ed8b82c ("sctp: introduce round robin stream scheduler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp_csum_xxx doesn't really match the param types of these common
csum apis. As sctp_csum_xxx is defined in sctp/checksum.h, many sparse
errors occur when make C=2 not only with M=net/sctp but also with other
modules that include this header file.
This patch is to force them fit in csum apis with the right types.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to force SCTP_ERROR_INV_STRM with right type to
fit in sctp_chunk_fail to avoid the sparse error.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccicheck warning which recommends to use memdup_user():
drivers/net/wan/lmc/lmc_main.c:497:27-34: WARNING opportunity for memdup_user
Generated by: scripts/coccinelle/memdup_user/memdup_user.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.
In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 10G PHY driver supports different hardware revisions, which
have their bits 3..0 differing. To get the correct revision number these
bits should be ignored. This patch fixes this by using the already
defined MARVELL_PHY_ID_MASK (0xfffffff0) instead of the custom
0xffffffff mask.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mvpp2: set of fixes
This series fixes various issues with the Marvell PPv2 driver. The
patches are sent together to avoid any possible conflict. The series is
based on today's net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes: 1d17db08c0 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: GRE offloading fixes
Petr says:
This patchset fixes a couple bugs in offloading GRE tunnels in mlxsw
driver.
Patch #1 fixes a problem that local routes pointing at a GRE tunnel
device are offloaded even if that netdevice is down.
Patch #2 detects that as a result of moving a GRE netdevice to a
different VRF, two tunnels now have a conflict of local addresses,
something that the mlxsw driver can't offload.
Patch #3 fixes a FIB abort caused by forming a route pointing at a
GRE tunnel that is eligible for offloading but already onloaded.
Patch #4 fixes a problem that next hops migrated to a new RIF kept the
old RIF reference, which went dangling shortly afterwards.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.
Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().
Fixes: 0c5f1cd5ba ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.
Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.
However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.
So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-11-27
This series contains updates to e1000, e1000e and i40e.
Gustavo A. R. Silva fixes a sizeof() issue where we were taking the size of
the pointer (which is always the size of the pointer).
Sasha does a follow up fix to a previous fix for buffer overrun, to resolve
community feedback from David Laight and the use of magic numbers.
Amritha fixes the reporting of error codes for when adding a cloud filter
fails.
Ahmad Fatoum brushes the dust off the e1000 driver to fix a code comment
and debug message which was incorrect about what the code was really doing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a follow on to commit b10effb92e ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
sizeof when applied to a pointer typed expression gives the size of
the pointer.
The proper fix in this particular case is to code sizeof(*vfres)
instead of sizeof(vfres).
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
KASAN revealed another access after delete in group.c. This time
it found that we read the header of a received message after the
buffer has been released.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2:
* Replace busy wait with wait_event()/wake_up_all()
* Cannot garantee that at the time xennet_remove is called, the
xen_netback state will not be XenbusStateClosed, so added a
condition for that
* There's a small chance for the xen_netback state is
XenbusStateUnknown by the time the xen_netfront switches to Closed,
so added a condition for that.
When unloading module xen_netfront from guest, dmesg would output
warning messages like below:
[ 105.236836] xen:grant_table: WARNING: g.e. 0x903 still in use!
[ 105.236839] deferring g.e. 0x903 (pfn 0x35805)
This problem relies on netfront and netback being out of sync. By the time
netfront revokes the g.e.'s netback didn't have enough time to free all of
them, hence displaying the warnings on dmesg.
The trick here is to make netfront to wait until netback frees all the g.e.'s
and only then continue to cleanup for the module removal, and this is done by
manipulating both device states.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
-----BEGIN PGP SIGNATURE-----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=ODX1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Four fixes:
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: a bunch of fixes for stream reconfig
This patchset is to make stream reset and asoc reset work more correctly
for stream reconfig.
Thank to Marcelo making them very clear.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing asoc reset, if the sender of the response has already sent some
chunk and increased asoc->next_tsn before the duplicate request comes, the
response will use the old result with an incorrect sender next_tsn.
Better than asoc->next_tsn, asoc->ctsn_ack_point can't be changed after
the sender of the response has performed the asoc reset and before the
peer has confirmed it, and it's value is still asoc->next_tsn original
value minus 1.
This patch sets sender next_tsn for the old result with ctsn_ack_point
plus 1 when processing the duplicate request, to make sure the sender
next_tsn value peer gets will be always right.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when doing asoc reset, it cleans up sacked and abandoned queues
by calling sctp_outq_free where it also cleans up unsent, retransmit
and transmitted queues.
It's safe for the sender of response, as these 3 queues are empty at
that time. But when the receiver of response is doing the reset, the
users may already enqueue some chunks into unsent during the time
waiting the response, and these chunks should not be flushed.
To void the chunks in it would be removed, it moves the queue into a
temp list, then gets it back after sctp_outq_free is done.
The patch also fixes some incorrect comments in
sctp_process_strreset_tsnreq.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it says in rfc6525#section5.1.4, before sending the request,
C2: The sender has either no outstanding TSNs or considers all
outstanding TSNs abandoned.
Prior to this patch, it tried to consider all outstanding TSNs abandoned
by dropping all chunks in all outqs with sctp_outq_free (even including
sacked, retransmit and transmitted queues) when doing this reset, which
is too aggressive.
To make it work gently, this patch will only allow the asoc reset when
the sender has no outstanding TSNs by checking if unsent, transmitted
and retransmit are all empty with sctp_outq_is_empty before sending
and processing the request.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the out stream reset in sctp stream reconf could be done even if
the stream outq is not empty. It means that users can not be sure
since which msg the new ssn will be used.
To make this more synchronous, it shouldn't allow to do out stream
reset until these chunks in unsent outq all are sent out.
This patch checks the corresponding stream outqs when sending and
processing the request . If any of them has unsent chunks in outq,
it will return -EAGAIN instead or send SCTP_STRRESET_IN_PROGRESS
back to the sender.
Fixes: 7f9d68ac94 ("sctp: implement sender-side procedures for SSN Reset Request Parameter")
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in stream reconf part there are still some places using magic
number 2 for each stream number length. To make it more readable,
this patch is to replace them with sizeof(__u16).
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing HW restart we tear down aggregations.
Since at this point we are not TX'ing any aggregation, while
the peer is still sending RX aggregation over the air, it will
make sense to tear down the RX aggregations first.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous path metric update from RANN frame has not considered
the own link metric toward the transmitting mesh STA. Fix this.
Reported-by: Michael65535
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we want to add a datapath flow, which has more than 500 vxlan outputs'
action, we will get the following error reports:
openvswitch: netlink: Flow action size 32832 bytes exceeds max
openvswitch: netlink: Flow action size 32832 bytes exceeds max
openvswitch: netlink: Actions may not be safe on all matching packets
... ...
It seems that we can simply enlarge the MAX_ACTIONS_BUFSIZE to fix it, but
this is not the root cause. For example, for a vxlan output action, we need
about 60 bytes for the nlattr, but after it is converted to the flow
action, it only occupies 24 bytes. This means that we can still support
more than 1000 vxlan output actions for a single datapath flow under the
the current 32k max limitation.
So even if the nla_len(attr) is larger than MAX_ACTIONS_BUFSIZE, we
shouldn't report EINVAL and keep it move on, as the judgement can be
done by the reserve_sfa_size.
Signed-off-by: zhangliping <zhangliping02@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gso_type is being used in binary AND operations together with SKB_GSO_UDP.
The issue is that variable gso_type is of type unsigned short and
SKB_GSO_UDP expands to more than 16 bits:
SKB_GSO_UDP = 1 << 16
this makes any binary AND operation between gso_type and SKB_GSO_UDP to
be always zero, hence making some code unreachable and likely causing
undesired behavior.
Fix this by changing the data type of variable gso_type to unsigned int.
Addresses-Coverity-ID: 1462223
Fixes: 0c19f846d5 ("net: accept UFO datagrams from tuntap and packet")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New file seems to have missed the SPDX license scan and update.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the refcount to 0 when allocating a tree to match the number of
switch devices it holds may cause an 'increment on 0; use-after-free',
if CONFIG_REFCOUNT_FULL is enabled.
To fix this, do not decrement the refcount of a newly allocated tree,
increment it when an already allocated tree is found, and decrement it
after the probing of a switch, as done with the previous behavior.
At the same time, make dsa_tree_get and dsa_tree_put accept a NULL
argument to simplify callers, and return the tree after incrementation,
as most kref users like of_node_get and of_node_put do.
Fixes: 8e5bf9759a ("net: dsa: simplify tree reference counting")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the host personality, VMCI will grab a mutex for any
queue pair access. In the detach callback for the vmci vsock
transport, we call vsock_stream_has_data while holding a spinlock,
and vsock_stream_has_data will access a queue pair.
To avoid this, we can simply omit calling vsock_stream_has_data
for host side queue pairs, since the QPs are empty per default
when the guest has detached.
This bug affects users of VMware Workstation using kernel version
4.4 and later.
Testing: Ran vsock tests between guest and host, and verified that
with this change, the host isn't calling vsock_stream_has_data
during detach. Ran mixedTest between guest and host using both
guest and host as server.
v2: Rebased on top of recent change to sk_state values
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_block_put_ext has assumed that all filters (and thus their goto
actions) are destroyed in RCU callback and thus can not race with our
list iteration. However, that is not true during netns cleanup (see
tcf_exts_get_net comment).
Prevent the user after free by holding all chains (except 0, that one is
already held). foreach_safe is not enough in this case.
To reproduce, run the following in a netns and then delete the ns:
ip link add dtest type dummy
tc qdisc add dev dtest ingress
tc filter add dev dtest chain 1 parent ffff: handle 1 prio 1 flower action goto chain 2
Fixes: 822e86d997 ("net_sched: remove tcf_block_put_deferred()")
Signed-off-by: Roman Kapl <code@rkapl.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86dabda426 ("net: thunderbolt: Clear finished Tx frame bus
address in tbnet_tx_callback()") fixed a DMA-API violation where the
driver called dma_unmap_page() in tbnet_free_buffers() for a bus address
that might already be unmapped. The fix was to zero out the bus address
of a frame in tbnet_tx_callback().
However, as pointed out by David Miller, zero might well be valid
mapping (at least in theory) so it is not good idea to use it here.
It turns out that we don't need the whole map/unmap dance for Tx buffers
at all. Instead we can map the buffers when they are initially allocated
and unmap them when the interface is brought down. In between we just
DMA sync the buffers for the CPU or device as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't offload IP header checksum to NIC.
This fixes a previous patch which enabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting enabled for IPv6 pkts. And HW is dropping these pkts
as it assumes the pkt is IPv4 when IP csum offload is set
in the SQ descriptor.
Fixes: 3a9024f52c ("net: thunderx: Enable TSO and checksum offloads for ipv6")
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When regulatory database certificates are built-in, they're
currently using the SHA256 digest algorithm, so add that to
the build in that case.
Also add a note that for custom certificates, one may need
to add the right algorithms.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function pci_unmap_page is obsolete. So it is replaced with
the function dma_unmap_page.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=Rakt
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes and improvements
Here's a set of patches that fix and improve some stuff in the AF_RXRPC
protocol:
The patches are:
(1) Unlock mutex returned by rxrpc_accept_call().
(2) Don't set connection upgrade by default.
(3) Differentiate the call->user_mutex used by the kernel from that used
by userspace calling sendmsg() to avoid lockdep warnings.
(4) Delay terminal ACK transmission to a work queue so that it can be
replaced by the next call if there is one.
(5) Split the call parameters from the connection parameters so that more
call-specific parameters can be passed through.
(6) Fix the call timeouts to work the same as for other RxRPC/AFS
implementations.
(7) Don't transmit DELAY ACKs immediately, but instead delay them slightly
so that can be discarded or can represent more packets.
(8) Use RTT to calculate certain protocol timeouts.
(9) Add a timeout to detect lost ACK/DATA packets.
(10) Add a keepalive function so that we ping the peer if we haven't
transmitted for a short while, thereby keeping intervening firewall
routes open.
(11) Make service endpoints expire like they're supposed to so that the UDP
port can be reused.
(12) Fix connection expiry timers to make cleanup happen in a more timely
fashion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the rxrpc connection expiry timers so that connections for closed
AF_RXRPC sockets get deleted in a more timely fashion, freeing up the
transport UDP port much more quickly.
(1) Replace the delayed work items with work items plus timers so that
timer_reduce() can be used to shorten them and so that the timer
doesn't requeue the work item if the net namespace is dead.
(2) Don't use queue_delayed_work() as that won't alter the timeout if the
timer is already running.
(3) Don't rearm the timers if the network namespace is dead.
Signed-off-by: David Howells <dhowells@redhat.com>
RxRPC service endpoints expire like they're supposed to by the following
means:
(1) Mark dead rxrpc_net structs (with ->live) rather than twiddling the
global service conn timeout, otherwise the first rxrpc_net struct to
die will cause connections on all others to expire immediately from
then on.
(2) Mark local service endpoints for which the socket has been closed
(->service_closed) so that the expiration timeout can be much
shortened for service and client connections going through that
endpoint.
(3) rxrpc_put_service_conn() needs to schedule the reaper when the usage
count reaches 1, not 0, as idle conns have a 1 count.
(4) The accumulator for the earliest time we might want to schedule for
should be initialised to jiffies + MAX_JIFFY_OFFSET, not ULONG_MAX as
the comparison functions use signed arithmetic.
(5) Simplify the expiration handling, adding the expiration value to the
idle timestamp each time rather than keeping track of the time in the
past before which the idle timestamp must go to be expired. This is
much easier to read.
(6) Ignore the timeouts if the net namespace is dead.
(7) Restart the service reaper work item rather the client reaper.
Signed-off-by: David Howells <dhowells@redhat.com>
We need to transmit a packet every so often to act as a keepalive for the
peer (which has a timeout from the last time it received a packet) and also
to prevent any intervening firewalls from closing the route.
Do this by resetting a timer every time we transmit a packet. If the timer
ever expires, we transmit a PING ACK packet and thereby also elicit a PING
RESPONSE ACK from the other side - which prevents our last-rx timeout from
expiring.
The timer is set to 1/6 of the last-rx timeout so that we can detect the
other side going away if it misses 6 replies in a row.
This is particularly necessary for servers where the processing of the
service function may take a significant amount of time.
Signed-off-by: David Howells <dhowells@redhat.com>
Eric Dumazet