Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are already various drivers having bigger label than 10 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.
Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.
This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Lee Schermerhorn noticed yesterday that I broke the mapping_writably_mapped
test in 2.6.7! Bad bad bug, good good find.
The i_mmap_writable count must be incremented for VM_SHARED (just as
i_writecount is for VM_DENYWRITE, but while holding the i_mmap_lock)
when dup_mmap() copies the vma for fork: it has its own more optimal
version of __vma_link_file(), and I missed this out. So the count
was later going down to 0 (dangerous) when one end unmapped, then
wrapping negative (inefficient) when the other end unmapped.
The only impact on x86 would have been that setting a mandatory lock on
a file which has at some time been opened O_RDWR and mapped MAP_SHARED
(but not necessarily PROT_WRITE) across a fork, might fail with -EAGAIN
when it should succeed, or succeed when it should fail.
But those architectures which rely on flush_dcache_page() to flush
userspace modifications back into the page before the kernel reads it,
may in some cases have skipped the flush after such a fork - though any
repetitive test will soon wrap the count negative, in which case it will
flush_dcache_page() unnecessarily.
Fix would be a two-liner, but mapping variable added, and comment moved.
Reported-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last patch to lib/idr.c caused a bug if idr_get_new_above() was
called on an empty idr.
Usually, nodes stay on the same layer. New layers are added to the top
of the tree.
The exception is idr_get_new_above() on an empty tree: In this case, the
new root node is first added on layer 0, then moved upwards. p->layer
was not updated.
As usual: You shall never rely on the source code comments, they will
only mislead you.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Give the correct size when reserving the interrupt vector table. It should be
a page not a single byte.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix __put_user_asm8() by jumping to the end label (3:) from the exception
handler, rather than jumping back to retry the second store instruction (label
2:).
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the preemption resume_kernel() routine by inverting the test to see
whether interrupts are off (IM7 is all enabled, not all disabled).
Furthermore, interrupts should be disabled on entry to resume_kernel() so that
they're correctly set for jumping to restore_all() and doing the need
reschedule test.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discard low-prioriy Tx interrupts when closing an MN10300 on-chip serial port.
The MN10300 on-chip serial port uses three interrupts to manage its serial
ports:
(1) A very high priority interrupt that drives virtual DMA for Rx.
(2) A very high priority interrupt that drives virtual DMA for Tx.
(3) A normal priority virtual interrupt that does the normal UART interrupt
stuff and is shared between Rx and Tx.
mn10300_serial_stop_tx() only disables the high priority Tx interrupt. It
doesn't also disable the normal priority one because it is shared with Rx.
However, the high priority interrupt may interrupt local_irq_disabled()
sections, and so may have queued up a low priority virtual interrupt whilst the
UART driver is asking for the Tx interrupt to be disabled.
The result of this can be an oops when we try to process the interrupt in
mn10300_serial_transmit_interrupt() as port->uart.info and port->uart.info->tty
may have gone away.
To deal with this, if either of those pointers is NULL, we make sure the
high-priority Tx interrupt is disabled and discard the interrupt. The low
priority interrupt is disabled by the mn10300_serial_pic irq_chip table.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include the linux/page.h header into the MN10300 kernel linker script thus
allowing us to use PAGE_SIZE macro instead of a numeric constant.
Also use the PERCPU macro instead of an explicit section definition.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCIe: ASPM: Break out of endless loop waiting for PCI config bits to switch
PCI: stop leaking 'slot_name' in pci_create_slot
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] SN: prevent IRQ retargetting in request_irq()
[IA64] Fix section mismatch ioc3uart_init()/ioc3uart_submodule
[IA64] Clear up section mismatch for ioc4_ide_attach_one.
[IA64] Clear up section mismatch with arch_unregister_cpu()
[IA64] Clear up section mismatch for sn_check_wars.
[IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel.
[IA64] Fix GRU compile error w/o CONFIG_HUGETLB_PAGE
[IA64] eliminate NULL test and memset after alloc_bootmem
[IA64] remove BUILD_BUG_ON from paravirt_getreg()
The pktcdvd created class devices only export some sysfs files,
but have no char dev_t registered in the driver.
At class device creation time they copy the dev_t value of the
block device to the char device, wich will register a new char
device in the driver core and userspace, with a conflicting dev_t
value.
In many cases the class devices dev_t just points to a random
USB device. This fixes the sysfs "duplicate entry" errors.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc64:
drivers/video/mb862xx/mb862xxfb.c:929: warning: long long unsigned int format, resource_size_t arg (arg 4)
drivers/video/mb862xx/mb862xxfb.c:931: warning: long long unsigned int format, resource_size_t arg (arg 4)
We don't know what type the architecture uses to implement u64, hence they
cannot be printed.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matteo Fortini <m.fortini@selcomgroup.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miles Lane tailing /sys files hit a BUG which Pekka Enberg has tracked
to my 966c8c12dc sprint_symbol(): use
less stack exposing a bug in slub's list_locations() -
kallsyms_lookup() writes a 0 to namebuf[KSYM_NAME_LEN-1], but that was
beyond the end of page provided.
The 100 slop which list_locations() allows at end of page looks roughly
enough for all the other stuff it might print after the symbol before
it checks again: break out KSYM_SYMBOL_LEN earlier than before.
Latencytop and ftrace and are using KSYM_NAME_LEN buffers where they
need KSYM_SYMBOL_LEN buffers, and vmallocinfo a 2*KSYM_NAME_LEN buffer
where it wants a KSYM_SYMBOL_LEN buffer: fix those before anyone copies
them.
[akpm@linux-foundation.org: ftrace.h needs module.h]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc Miles Lane <miles.lane@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On umount two event will be dispatched to watcher:
1: inotify_dev_queue_event(.., IN_UNMOUNT,..)
2: remove_watch(watch, dev)
->inotify_dev_queue_event(.., IN_IGNORED, ..)
But if watcher has IN_ONESHOT bit set then the watcher will be released
inside first event. Which result in accessing invalid object later. IMHO
it is not pure regression. This bug wasn't triggered while initial
inotify interface testing phase because of another bug in IN_ONESHOT
handling logic :)
commit ac74c00e49
Author: Ulisses Furquim <ulissesf@gmail.com>
Date: Fri Feb 8 04:18:16 2008 -0800
inotify: fix check for one-shot watches before destroying them
As the IN_ONESHOT bit is never set when an event is sent we must check it
in the watch's mask and not in the event's mask.
TESTCASE:
mkdir mnt
mount -ttmpfs none mnt
mkdir mnt/d
./inotify mnt/d&
umount mnt ## << lockup or crash here
TESTSOURCE:
/* gcc -oinotify inotify.c */
#include <stdio.h>
#include <stdlib.h>
#include <sys/inotify.h>
int main(int argc, char **argv)
{
char buf[1024];
struct inotify_event *ie;
char *p;
int i;
ssize_t l;
p = argv[1];
i = inotify_init();
inotify_add_watch(i, p, ~0);
l = read(i, buf, sizeof(buf));
printf("read %d bytes\n", l);
ie = (struct inotify_event *) buf;
printf("event mask: %d\n", ie->mask);
return 0;
}
Signed-off-by: Dmitri Monakhov <dmonakhov@openvz.org>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Cc: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_long_xchg() is not correctly defined for 32bit arches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 2f007e74bb, do_pages_stat()
gets the page address from user-space and puts the corresponding status
back while holding the mmap_sem for read. There is no need to hold
mmap_sem there while some page-faults may occur.
This patch adds a temporary address and status buffer so as to only
hold mmap_sem while working on these kernel buffers. This is
implemented by extracting do_pages_stat_array() out of do_pages_stat().
Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The large pages fix from bcf8039ed4 broke 32-bit pagemap by pulling the
pagemap entry code out into a function with the wrong return type.
Pagemap entries are 64 bits on all systems and unsigned long is only 32
bits on 32-bit systems.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Reported-by: Doug Graham <dgraham@nortel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a total bootup freeze on ia64.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build error when RTC_INTF_DEV=n:
drivers/rtc/rtc-twl4030.c:402: error: 'twl4030_rtc_ioctl' undeclared here (not in a function)
make[3]: *** [drivers/rtc/rtc-twl4030.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a call to cancel_work_sync() in fbcon_exit() to cancel any pending
work in the fbcon workqueue.
The current implementation of fbcon_exit() sets the fbcon workqueue
function info->queue.func to NULL, but does not assure that there is no
work pending when it does so. On occasion, depending on system timing,
there will still be pending work in the queue when fbcon_exit() is
called. This results in a null pointer deference when run_workqueue()
tries to call the queue's work function.
Fixes errors on shutdown similar to these:
Console: switching to colour dummy device 80x25
Unable to handle kernel paging request for data at address 0x00000000
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, lru_add_drain_all() has two version.
(1) use schedule_on_each_cpu()
(2) don't use schedule_on_each_cpu()
Gerald Schaefer reported it doesn't work well on SMP (not NUMA) S390
machine.
offline_pages() calls lru_add_drain_all() followed by drain_all_pages().
While drain_all_pages() works on each cpu, lru_add_drain_all() only runs
on the current cpu for architectures w/o CONFIG_NUMA. This let us run
into the BUG_ON(!PageBuddy(page)) in __offline_isolated_pages() during
memory hotplug stress test on s390. The page in question was still on the
pcp list, because of a race with lru_add_drain_all() and drain_all_pages()
on different cpus.
Actually, Almost machine has CONFIG_UNEVICTABLE_LRU=y. Then almost machine use
(1) version lru_add_drain_all although the machine is UP.
Then this ifdef is not valueable.
simple removing is better.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert
commit e8ced39d5e
Author: Mingming Cao <cmm@us.ibm.com>
Date: Fri Jul 11 19:27:31 2008 -0400
percpu_counter: new function percpu_counter_sum_and_set
As described in
revert "percpu counter: clean up percpu_counter_sum_and_set()"
the new percpu_counter_sum_and_set() is racy against updates to the
cpu-local accumulators on other CPUs. Revert that change.
This means that ext4 will be slow again. But correct.
Reported-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert
commit 1f7c14c62c
Author: Mingming Cao <cmm@us.ibm.com>
Date: Thu Oct 9 12:50:59 2008 -0400
percpu counter: clean up percpu_counter_sum_and_set()
Before this patch we had the following:
percpu_counter_sum(): return the percpu_counter's value
percpu_counter_sum_and_set(): return the percpu_counter's value, copying
that value into the central value and zeroing the per-cpu counters before
returning.
After this patch, percpu_counter_sum_and_set() has gone, and
percpu_counter_sum() gets the old percpu_counter_sum_and_set()
functionality.
Problem is, as Eric points out, the old percpu_counter_sum_and_set()
functionality was racy and wrong. It zeroes out counters on "other" cpus,
without holding any locks which will prevent races agaist updates from
those other CPUS.
This patch reverts 1f7c14c62c. This means
that percpu_counter_sum_and_set() still has the race, but
percpu_counter_sum() does not.
Note that this is not a simple revert - ext4 has since started using
percpu_counter_sum() for its dirty_blocks counter as well.
Note that this revert patch changes percpu_counter_sum() semantics.
Before the patch, a call to percpu_counter_sum() will bring the counter's
central counter mostly up-to-date, so a following percpu_counter_read()
will return a close value.
After this patch, a call to percpu_counter_sum() will leave the counter's
central accumulator unaltered, so a subsequent call to
percpu_counter_read() can now return a significantly inaccurate result.
If there is any code in the tree which was introduced after
e8ced39d5e was merged, and which depends
upon the new percpu_counter_sum() semantics, that code will break.
Reported-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should first delete the counter from percpu_counters list
before freeing memory, or a percpu_counter_hotcpu_callback()
could dereference a NULL pointer.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing id_table to the drivers in subject. Patch is against the
latest git. It should go in with 2.6.28 if possible, the drivers won't
work without the id_table bits.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Reported-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Running kmemtraced, which uses splice() on relayfs, causes a hard lock on
x86-64 SMP. As described by Tom Zanussi:
It looks like you hit the same problem as described here:
commit 8191ecd1d1
splice: fix infinite loop in generic_file_splice_read()
relay uses the same loop but it never got noticed or fixed.
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Tested-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mconsole_init() passed 256 bytes as length in os_create_unix_socket, while
the sizeof UNIX_PATH_MAX is 108. This patch fixes that problem and avoids
a big overrun bug reported on UML bootup.
sockaddr_un.sun_path is UNIX_PATH_MAX long which causes the problem.
Reported-by: Vikas K Managutte <vikki.km@gmail.com>
Reported-by: Sarvesh Kumar Lal Das <skldas@gmail.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: WANG Cong <wangcong@zeuux.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org> [please check with Jeff]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On second thoughts, this is just going to disturb people while telling us
things which we already knew.
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have at least one algorithm built-in then it no longer makes
sense to have the testing framework, and hence cryptomgr to be a
module. It should be either on or off, i.e., built-in or disabled.
This just happens to stop a potential runaway modprobe loop that
seems to trigger on at least one distro.
With fixes from Evgeniy Polyakov.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a DMA map/ unmap imbalance whenever a block write request
packet is sent and then dequeued with ohci_cancel_packet. The latter
may happen frequently if the AR resp tasklet is executed before the AT
req tasklet for the same transaction.
Add the missing dma_unmap_single. This fixes
https://bugzilla.redhat.com/show_bug.cgi?id=475156
Reported-by: Emmanuel Kowalski
Tested-by: Emmanuel Kowalski
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The patch 6341c39 "tracehook: exec" introduced a small regression in
2.6.27 regarding binfmt_misc exec event reporting. Since the reporting
is now done in the common search_binary_handler() function, an exec
of a misc binary will result in two (or possibly multiple) exec events
being reported, instead of just a single one, because the misc handler
contains a recursive call to search_binary_handler.
To add to the confusion, if PTRACE_O_TRACEEXEC is not active, the multiple
SIGTRAP signals will in fact cause only a single ptrace intercept, as the
signals are not queued. However, if PTRACE_O_TRACEEXEC is on, the debugger
will actually see multiple ptrace intercepts (PTRACE_EVENT_EXEC).
The test program included below demonstrates the problem.
This change fixes the bug by calling tracehook_report_exec() only in the
outermost search_binary_handler() call (bprm->recursion_depth == 0).
The additional change to restore bprm->recursion_depth after each binfmt
load_binary call is actually superfluous for this bug, since we test the
value saved on entry to search_binary_handler(). But it keeps the use of
of the depth count to its most obvious expected meaning. Depending on what
binfmt handlers do in certain cases, there could have been false-positive
tests for recursion limits before this change.
/* Test program using PTRACE_O_TRACEEXEC.
This forks and exec's the first argument with the rest of the arguments,
while ptrace'ing. It expects to see one PTRACE_EVENT_EXEC stop and
then a successful exit, with no other signals or events in between.
Test for kernel doing two PTRACE_EVENT_EXEC stops for a binfmt_misc exec:
$ gcc -g traceexec.c -o traceexec
$ sudo sh -c 'echo :test:M::foobar::/bin/cat: > /proc/sys/fs/binfmt_misc/register'
$ echo 'foobar test' > ./foobar
$ chmod +x ./foobar
$ ./traceexec ./foobar; echo $?
==> good <==
foobar test
0
$
==> bad <==
foobar test
unexpected status 0x4057f != 0
3
$
*/
#include <stdio.h>
#include <sys/types.h>
#include <sys/wait.h>
#include <sys/ptrace.h>
#include <unistd.h>
#include <signal.h>
#include <stdlib.h>
static void
wait_for (pid_t child, int expect)
{
int status;
pid_t p = wait (&status);
if (p != child)
{
perror ("wait");
exit (2);
}
if (status != expect)
{
fprintf (stderr, "unexpected status %#x != %#x\n", status, expect);
exit (3);
}
}
int
main (int argc, char **argv)
{
pid_t child = fork ();
if (child < 0)
{
perror ("fork");
return 127;
}
else if (child == 0)
{
ptrace (PTRACE_TRACEME);
raise (SIGUSR1);
execv (argv[1], &argv[1]);
perror ("execve");
_exit (127);
}
wait_for (child, W_STOPCODE (SIGUSR1));
if (ptrace (PTRACE_SETOPTIONS, child,
0L, (void *) (long) PTRACE_O_TRACEEXEC) != 0)
{
perror ("PTRACE_SETOPTIONS");
return 4;
}
if (ptrace (PTRACE_CONT, child, 0L, 0L) != 0)
{
perror ("PTRACE_CONT");
return 5;
}
wait_for (child, W_STOPCODE (SIGTRAP | (PTRACE_EVENT_EXEC << 8)));
if (ptrace (PTRACE_CONT, child, 0L, 0L) != 0)
{
perror ("PTRACE_CONT");
return 6;
}
wait_for (child, W_EXITCODE (0, 0));
return 0;
}
Reported-by: Arnd Bergmann <arnd@arndb.de>
CC: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
Makes a Compaq 6735s boot reliably again. It used to hang in the loop
on some boots. Give the link one second to train, otherwise break out
of the loop and reset the previously set clock bits.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In pci_create_slot(), the local variable 'slot_name' is allocated by
make_slot_name(), but never freed. We never use it after passing it to
the kobject core, so we should free it upon function exit.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the introduction of the generic affinity autoselector,
irq_select_affinity(), IRQs are now being retargetted,
using a default mask, via the request_irq() path.
This results in all IRQs targetted at CPU 0.
SN Altix assigns affinity in the SN PROM, and does not
expect that to be changed as part of request_irq().
Set the IRQ_AFFINITY_SET flag to prevent
request_irq() from resetting affinity.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The firewire nodemanager function "nodemgr_host_thread" contains a loop
that calls try_to_freeze near the top of the loop, but then delays for
up to 3.25 seconds (plus time to do work) before getting back to the top
of the loop. When starting a cycle post-boot, this doesn't seem to bite,
but it is causing a noticeable delay at boot time, when freezing
processes prior to starting to read the image.
The following patch adds invocation of try_to_freeze to the subloops
that are used in the body of this function. With these additions, the
time to freeze when starting to resume at boot time is virtually zero.
I'm no expert on firewire, and so don't know that we shouldn't check
the return value and jump back to the top of the loop or such like after
being frozen, but I submit it for your consideration.
Signed-off-by: Nigel Cunningham <nigel@tuxonice.net>
The delay until nodemgr freezes was up to 0.25s (plus time for node
probes) in Linux 2.6.27 and older and up to 3.25s (plus ~) since Linux
2.6.28-rc1, hence much more noticeable.
try_to_freeze() without any jump is correct. The surrounding code in
the respective loops will catch whether another bus reset happens during
the freeze and handle it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Impact: fix possible deadlock in CPU hot-remove path
This patch fixes a possible deadlock scenario in the CPU remove path.
migration_call grabs rq->lock, then wakes up everything on rq->migration_queue
with the lock held. Then one of the tasks on the migration queue ends up
calling tg_shares_up which then also tries to acquire the same rq->lock.
[c000000058eab2e0] c000000000502078 ._spin_lock_irqsave+0x98/0xf0
[c000000058eab370] c00000000008011c .tg_shares_up+0x10c/0x20c
[c000000058eab430] c00000000007867c .walk_tg_tree+0xc4/0xfc
[c000000058eab4d0] c0000000000840c8 .try_to_wake_up+0xb0/0x3c4
[c000000058eab590] c0000000000799a0 .__wake_up_common+0x6c/0xe0
[c000000058eab640] c00000000007ada4 .complete+0x54/0x80
[c000000058eab6e0] c000000000509fa8 .migration_call+0x5fc/0x6f8
[c000000058eab7c0] c000000000504074 .notifier_call_chain+0x68/0xe0
[c000000058eab860] c000000000506568 ._cpu_down+0x2b0/0x3f4
[c000000058eaba60] c000000000506750 .cpu_down+0xa4/0x108
[c000000058eabb10] c000000000507e54 .store_online+0x44/0xa8
[c000000058eabba0] c000000000396260 .sysdev_store+0x3c/0x50
[c000000058eabc10] c0000000001a39b8 .sysfs_write_file+0x124/0x18c
[c000000058eabcd0] c00000000013061c .vfs_write+0xd0/0x1bc
[c000000058eabd70] c0000000001308a4 .sys_write+0x68/0x114
[c000000058eabe30] c0000000000086b4 syscall_exit+0x0/0x40
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Brownell