IPv6 uses 2 TIDs with CLIP enabled and 4 TIDs without CLIP.
Currently we are incrementing STIDs in use by 1 for both IPv4 and IPv6 which
is wrong.
Further, driver currently does not have interface to query if CLIP is programmed
for particular IPv6 address. So, in this patch we increment/decrement TIDs in use
by 4 for IPv6 assuming absence of CLIP. Such assumption keeps us on safe side and
we don't end up allocating more stids for IPv6 than actually supported.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LE workaround code is incorrectly reusing the TCAM TIDs
(meant for allocation by firmware in case of hash collisions) for filter
servers. This patch assigns the filter server TIDs properly starting from
sftid_base index.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were creating LE Workaround Server Filters without specifying
IPPROTO_TCP (6) in the filters (when F_PROTOCOL is set in TP_VLAN_PRI_MAP).
This meant that UDP packets with matching IP Addresses/Ports would get
caught up in the filter and be delivered to ULDs like iw_cxgb4.
So, include the protocol information in the server filter properly.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating offload server entries, an IPv6 passive connection request
can trigger a reply with a null STID, whereas the driver would expect
the reply 'STID to match the value used for the request.
This happens due to h/w limitation on T4 and T5.
This patch ensures that STID 0 is never used if the stid range starts
from zero.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please consider pulling this batch of fixes for the 3.13 stream...
For the mac80211 bits, Johannes says:
"Here's a fix for another potential radiotap parser buffer overrun thanks
to Evan Huus, and a fix for a cfg80211 warning in a certain corner case
(reconnecting to the same BSS)."
For the bluetooth bits, Gustavo says:
"Two patches in this pull request. An important fix from Marcel in the
permission check for HCI User Channels, there was a extra check for
CAP_NET_RAW, and it was now removed. These channels should only require
CAP_NET_ADMIN. The other patch is a device id addition."
On top of that...
Sujith Manoharan provides a workaround for a hardware problem that
can result in lost interrupts.
Larry Finger fixes an oops when unloading the rtlwifi driver (Red
Hat bug 852761).
Mathy Vanhoef fixes a somewhat minor MAC address privacy issue
(CVE-2013-4579).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the register_netdev to the end of probe to prevent
possible open call happens before NetVSP is connected.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to net, ixgbe and e1000e.
David provides compiler fixes for e1000e.
Don provides a fix for ixgbe to resolve a compile warning.
John provides a fix to net where it is useful to be able to walk all
upper devices when bringing a device online where the RTNL lock is held.
In this case, it is safe to walk the all_adj_list because the RTNL lock is
used to protect the write side as well. This patch adds a check to see
if the RTNL lock is held before throwing a warning in
netdev_all_upper_get_next_dev_rcu().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This version corrects the whitespace issue.
orion_mdio_wait_ready uses wait_event_timeout to wait for the
SMI interrupt to fire. wait_event_timeout waits for between
"timeout - 1" and "timeout" jiffies. In this case a 1ms timeout
when HZ is 1000 results in a wait of 0 to 1 jiffies, causing
premature timeouts.
This fix ensures a minimum timeout of 2 jiffies, ensuring
wait_event_timeout will always wait at least 1 jiffie.
Issue reported by Nicolas Schichan.
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function atl1c_reset_pcie() does not check the return from
pci_find_ext_cabability() where it is getting the postion of the
PCI_EXT_CAP_ID_ERR. It is possible for the return to be 0.
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: de5fb0a053 ("net: fec: put tx to napi poll function to fix dead lock")
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"valid ME register value" is not an error. It should be logged for
debugging only.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The yam_ioctl() code fails to initialise the cmd field
of the struct yamdrv_ioctl_cfg. Add an explicit memset(0)
before filling the structure to avoid the 4-byte info leak.
Signed-off-by: Salva Peiró <speiro@ai2.upv.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'bi' comes from userspace. If userspace passed a
large number to 'bi.data.calibrate', there would be an integer overflow
in the following line:
s->hdlctx.calibrate = bi.data.calibrate * s->par.bitrate / 16;
Signed-off-by: Wenliang Fan <fanwlexca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'err' is overwrited to 0 after maybe_pull_tail() call, so the error
code was not set if skb_partial_csum_set() call failed. Fix to return
error -EPROTO from those error handling case instead of 0.
Fixes: d52eb0d46f ('xen-netback: make sure skb linear area covers checksum field')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain dm962x revisions contain an bug, where if a USB bulk transfer retry
(E.G. if bulk crc mismatch) happens right after a transfer with odd or
maxpacket length, the internal tx hardware fifo gets out of sync causing
the interface to stop working.
Work around it by adding up to 3 bytes of padding to ensure this situation
cannot trigger.
This workaround also means we never pass multiple-of-maxpacket size skb's
to usbnet, so the length adjustment to handle usbnet's padding of those can
be removed.
Cc: <stable@vger.kernel.org>
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver nowadays also support dm9620/dm9621a based USB 2.0 ethernet
adapters, so adjust module/driver description and Kconfig help text to
match.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9620/dm9621a require room for 4 byte padding even in dm9601 (3 byte
header) mode.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9621a is functionally identical to dm9620, so the existing handling can
directly be used.
Thanks to Davicom for sending me a dongle.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling In Band mode in 10 mbps speed.
RGMII supports 1 Gig and 100 mbps mode for Forced mode of operation.
For 10mbps mode it should be configured to in band mode so that link
status, duplexity and speed are determined from the RGMII input data
stream
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_3ad_handle_link_change is called with RTNL only,
and the function will modify the port's information with
no further locking, it will not mutex against bond state
machine and incoming LACPDU which do not hold RTNL, So I
add __get_state_machine_lock to protect the port.
But it is not a critical bug, it exist since day one, and till
now it has never been hit and reported, because changes to
speed is very rare, and will not occur critical problem.
The comments in the function is very old, cleanup it and
add a new pr_debug to debug the port message.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh said that the bond_3ad_adapter_duplex_changed is
called with RTNL only, and the function will modify the port's
information with no further locking, it will not mutex against
bond state machine and incoming LACPDU which do not hold RTNL,
So I add __get_state_machine_lock to protect the port.
But it is not a critical bug, it exist since day one, and till
now it has never been hit and reported, because changes to
speed is very rare, and will not occur critical problem.
The comments in the function is very old, cleanup it.
Suggested-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh said that the bond_3ad_adapter_speed_changed is
called with RTNL only, and the function will modify the port's
information with no further locking, it will not mutex against
bond state machine and incoming LACPDU which do not hold RTNL,
So I add __get_state_machine_lock to protect the port.
But it is not a critical bug, it exist since day one, and till
now it has never been hit and reported, because changes to
speed is very rare, and will not occur critical problem.
The comment in the function is very old, cleanup it.
Suggested-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_PCI_IOV isn't defined we get an "unused variable" warining so
now wrap the variable declaration like it's usage already was.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to fix a compiler warning of maybe-uininitialized-variable
that is generated from gcc when the -O3 flag is used. In the function
e1000_reset_hw_80003es2lan(), the variable krmn_reg_data is first given
a value by being passed to a register read function as a
pass-by-reference parameter. But, the return value of that read
function was never checked to see if the read failed and the variable
not given an initial value. The compiler was smart enough to spot
this. This patch is to check the return value for that read function
and return it, if an error occurs, without trying to utilize the value
in kmrn_reg_data.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to fix a compiler warning of __bad_udelay due to a value
of >999 being passed as a parameter to udelay() in the function
e1000e_phy_has_link_generic(). This affects the gcc compiler when
it is given a flag of -O3 and the icc compiler.
This patch is also making the change from mdelay() to msleep() in the
same function, since it was determined though code inspection that this
function is never called in atomic context.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Marc Kleine-Budde says:
====================
this is a pull request with two fixes for net/master, the current release
cycle.
It consists of a patch by Alexey Khoroshilov from the Linux Driver Verification
project, which fixes a memory leak in ems_usb's failure patch. And a patch by
me which fixes a memory leak in the peak usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not enable mailbox polling in case of legacy interrupt.
Process mailbox AEN/response from the interrupt.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow driver to collect firmware dump, during a forced firmware dump
operation, when auto firmware recovery is disabled. Also, during this
operation, driver should not allow reset recovery to be performed.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use vzalloc() instead of kzalloc() for allocation of
bootloader size memory. kzalloc() may fail to allocate
the size of bootloader
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Current code was not allowing the user to configure more
than one Tx ring using ethtool for 83xx/84xx adapter.
This regression was introduced by commit id
18afc102fd ("qlcnic: Enable
multiple Tx queue support for 83xx/84xx Series adapter.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TSS/RSS ring validation does not take into account that either
of these ring values can be 0. This patch fixes this validation
and would fail set_channel operation if any of these ring value
is 0. This regression was added as part of commit id
34e8c406fd ("qlcnic: refactor Tx/SDS
ring calculation and validation in driver.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver should re-allocate all Tx queues after completing
diagnostic tests. This regression was added by commit id
c2c5e3a068 ("qlcnic: Enable
diagnostic test for multiple Tx queues.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was using netif_tx_{stop,wake}_all_queues() api
during link change event. Remove these api calls to
manage queue start/stop event, as core networking stack
will manage this based on netif_carrier_{on,off} call.
These API's were modified as part of commit id
012ec81223 ("qlcnic: Multi Tx
queue support for 82xx Series adapter.")
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -EPROTO error if fragments detected in checksum_setup_ip().
Fixes: 1431fb31ec ('xen-netback: fix fragment detection in checksum setup')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a possible deadlock if we flush the peers notifying work during setting
mtu:
[ 22.991149] ======================================================
[ 22.991173] [ INFO: possible circular locking dependency detected ]
[ 22.991198] 3.10.0-54.0.1.el7.x86_64.debug #1 Not tainted
[ 22.991219] -------------------------------------------------------
[ 22.991243] ip/974 is trying to acquire lock:
[ 22.991261] ((&(&net_device_ctx->dwork)->work)){+.+.+.}, at: [<ffffffff8108af95>] flush_work+0x5/0x2e0
[ 22.991307]
but task is already holding lock:
[ 22.991330] (rtnl_mutex){+.+.+.}, at: [<ffffffff81539deb>] rtnetlink_rcv+0x1b/0x40
[ 22.991367]
which lock already depends on the new lock.
[ 22.991398]
the existing dependency chain (in reverse order) is:
[ 22.991426]
-> #1 (rtnl_mutex){+.+.+.}:
[ 22.991449] [<ffffffff810dfdd9>] __lock_acquire+0xb19/0x1260
[ 22.991477] [<ffffffff810e0d12>] lock_acquire+0xa2/0x1f0
[ 22.991501] [<ffffffff81673659>] mutex_lock_nested+0x89/0x4f0
[ 22.991529] [<ffffffff815392b7>] rtnl_lock+0x17/0x20
[ 22.991552] [<ffffffff815230b2>] netdev_notify_peers+0x12/0x30
[ 22.991579] [<ffffffffa0340212>] netvsc_send_garp+0x22/0x30 [hv_netvsc]
[ 22.991610] [<ffffffff8108d251>] process_one_work+0x211/0x6e0
[ 22.991637] [<ffffffff8108d83b>] worker_thread+0x11b/0x3a0
[ 22.991663] [<ffffffff81095e5d>] kthread+0xed/0x100
[ 22.991686] [<ffffffff81681c6c>] ret_from_fork+0x7c/0xb0
[ 22.991715]
-> #0 ((&(&net_device_ctx->dwork)->work)){+.+.+.}:
[ 22.991715] [<ffffffff810de817>] check_prevs_add+0x967/0x970
[ 22.991715] [<ffffffff810dfdd9>] __lock_acquire+0xb19/0x1260
[ 22.991715] [<ffffffff810e0d12>] lock_acquire+0xa2/0x1f0
[ 22.991715] [<ffffffff8108afde>] flush_work+0x4e/0x2e0
[ 22.991715] [<ffffffff8108e1b5>] __cancel_work_timer+0x95/0x130
[ 22.991715] [<ffffffff8108e303>] cancel_delayed_work_sync+0x13/0x20
[ 22.991715] [<ffffffffa03404e4>] netvsc_change_mtu+0x84/0x200 [hv_netvsc]
[ 22.991715] [<ffffffff815233d4>] dev_set_mtu+0x34/0x80
[ 22.991715] [<ffffffff8153bc2a>] do_setlink+0x23a/0xa00
[ 22.991715] [<ffffffff8153d054>] rtnl_newlink+0x394/0x5e0
[ 22.991715] [<ffffffff81539eac>] rtnetlink_rcv_msg+0x9c/0x260
[ 22.991715] [<ffffffff8155cdd9>] netlink_rcv_skb+0xa9/0xc0
[ 22.991715] [<ffffffff81539dfa>] rtnetlink_rcv+0x2a/0x40
[ 22.991715] [<ffffffff8155c41d>] netlink_unicast+0xdd/0x190
[ 22.991715] [<ffffffff8155c807>] netlink_sendmsg+0x337/0x750
[ 22.991715] [<ffffffff8150d219>] sock_sendmsg+0x99/0xd0
[ 22.991715] [<ffffffff8150d63e>] ___sys_sendmsg+0x39e/0x3b0
[ 22.991715] [<ffffffff8150eba2>] __sys_sendmsg+0x42/0x80
[ 22.991715] [<ffffffff8150ebf2>] SyS_sendmsg+0x12/0x20
[ 22.991715] [<ffffffff81681d19>] system_call_fastpath+0x16/0x1b
This is because we hold the rtnl_lock() before ndo_change_mtu() and try to flush
the work in netvsc_change_mtu(), in the mean time, netdev_notify_peers() may be
called from worker and also trying to hold the rtnl_lock. This will lead the
flush won't succeed forever. Solve this by not canceling and flushing the work,
this is safe because the transmission done by NETDEV_NOTIFY_PEERS was
synchronized with the netif_tx_disable() called by netvsc_change_mtu().
Reported-by: Yaju Cao <yacao@redhat.com>
Tested-by: Yaju Cao <yacao@redhat.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver workaround for a HW issue.
A race condition in the HW results in missing interrupts,
which can be avoided by a read/write with the ISR register.
All chips in the AR9002 series are affected by this bug - AR9003
and above do not have this problem.
Cc: stable@vger.kernel.org
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Fedora systems, unloading rtl8192ce causes an oops. This patch fixes the
problem reported at https://bugzilla.redhat.com/show_bug.cgi?id=852761.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak in pcan_usb_pro_init(). In patch
f14e224 net: can: peak_usb: Do not do dma on the stack
the struct pcan_usb_pro_fwinfo *fi and struct pcan_usb_pro_blinfo *bi were
converted from stack to dynamic allocation va kmalloc(). However the
corresponding kfree() was not introduced.
This patch adds the missing kfree().
Cc: linux-stable <stable@vger.kernel.org> # v3.10
Reported-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are a couple failure paths where urb leaks.
Is spare code within ems_usb_start_xmit(),
usb_free_urb() should be used to deallocate urb instead of usb_unanchor_urb().
In ems_usb_start() there is no usb_free_urb() if usb_submit_urb() fails.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.
CC: stable kernel <stable@vger.kernel.org> # 3.9+
Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a mistake in checking the gso_prefix mask when passing large
packets to a guest. The wrong shift is applied to the bit - the raw skb
gso type is used rather then the translated one. This leads to large packets
being handed to the guest without the GSO metadata. This patch fixes the
check.
The mistake manifested as errors whilst running Microsoft HCK large packet
offload tests between a pair of Windows 8 VMs. I have verified this patch
fixes those errors.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPSW and Davinci MDIO are build as modules, CPSW crashes when
accessing CPSW registers in CPSW probe. The same is working in built-in
as the CPSW clocks are enabled in Davindi MDIO probe, SO Enabling the
clocks before accessing the version register and moving out the other
register access to cpsw device open.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_build_tx_gops to a check for RING_HAS_UNCONSUMED_REQUESTS as the
former call has the side effect of advancing the ring event pointer and
therefore inviting another interrupt from the frontend before the napi
poll has actually finished, thereby defeating the point of napi.
The event pointer is updated by RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_poll, the napi poll function, if the work done is less than the
budget i.e. when actually transitioning back to interrupt mode.
Reported-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback seems to be somewhat confused about the napi budget parameter. The
parameter is supposed to limit the number of skbs processed in each poll,
but netback has this confused with grant operations.
This patch fixes that, properly limiting the work done in each poll. Note
that this limit makes sure we do not process any more data from the shared
ring than we intend to pass back from the poll. This is important to
prevent tx_queue potentially growing without bound.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 031916568a worked around
errata ERR006358, but comment contains duplicated lines, impairing
the readability. Remove them.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi