This patch adds support for enabling/disabling optional device specific
features through sysfs properties at runtime.
* High-impedance mode enable/disable
* Sysoff enable/disable
Refer to the respective device datasheets for more information:
http://www.ti.com/product/bq24250http://www.ti.com/product/bq24251http://www.ti.com/product/bq24257
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch allows reading and writing of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected (if the D+/D- USB signal-
based charger type detection is enabled) and to re-configure the maximum
current drawn from the external supply at runtime based on system-level
knowledge or user input. Note that upon charger disconnection and
re-connection the limit configured through firmware becomes active again
(or the D+/D- USB signal-based charger detection will be run again).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,in-dpm-voltage" is introduced
to allow configuring the input voltage threshold for the devices'
dynamic power path management (DPM) feature. In short, it can be used to
prevent the input voltage from dropping below a certain value as current
is drawn to charge the battery or supply the system.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,ovp-voltage" is introduced to
allow configuring the input over voltage protection setting.
This commit also adds the basic sysfs support for custom properties
which is being used to allow userspace to read the current ovp-voltage
setting.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,current-limit" is introduced
to allow disabling the D+/D- USB signal-based charger type auto-
detection algorithm used to set the input current limit and instead to
use a fixed input current limit.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adding a missing bit definition for the sake of consistency device model
vs. bit field representation. No change in functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds basic support for bq24250 and bq24251 which are very
similar to the bq24257 the driver was originally written for. Basic
support means the ability to select a device through Kconfig, DT and
ACPI, an instance variable allowing to check which chip is active, and
the reporting back of the selected device through the model_name power
supply sysfs property.
This patch by itself is not sufficient to actually use those two added
devices in a real-world setting due to some feature differences which
are addressed by other patches in this series.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Eliminate a few lines of code by using the PTR_ERR_OR_ZERO() macro.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the devm_* managed version of the function to register the power
supply and remove the associated unregister function. This will simplify
error handling moving forward as it allows the unregister to happen
automatically. It also saves a few lines of code.
As this changes the order of putting the bq24257 into reset vs.
unregistering the power-supply during driver remove re-tested various
driver unload scenario to make sure that this doesn't cause any
unintended side effects such as erroneous interrupts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The maximum amount of input current the charger should draw is dependent
on the power supply and should only be (re-)configured when the power
supply gets connected and disconnected. However the driver was also
lowering the bq24257's input current limit setting to 500mA when the
battery was removed and restored the previous setting according to the
power supply capabilities when the battery was reconnected although
these events are not impacting the amount of power that can be drawn
from the supply. Furthermore, a re-configuration of the input current
limit to 500mA when the battery gets disconnected is actually dangerous
if the limit was set higher previously and the system draws more than
500mA in which case the system voltage would be reduced in order to
maintain 500mA which could result in the system getting too low of a
supply to maintain operation. Last but not least the mechanism itself
used for battery re-connection detection did not work in corner cases
such as when the device's input current loop becomes active and the
bq24257 device clears its battery fault error resulting in incorrectly
reporting that the battery got reconnected.
This patches removes the impact the battery removal/insertion has on the
input current limit configured for the bq24257 and simplifies the
associated handler routine.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
At the time the driver was written GpioInt resources in ACPI were not
passed to the driver in client->irq, as opposed to DT enumeration. To
accommodate this use case, a "stat-gpios" property was introduced to
allow configuring the IRQ.
However this issue with ACPI was fixed in commit "845c877 i2c / ACPI:
Assign IRQ for devices that have GpioInt automatically" and makes this
workaround no longer necessary, hence we can remove the support for the
"stat-gpios" property and the associated code from the bq24257 driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We need flags to be signed for the error handling to work.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Fixes: 74aab849f3 ('power: bq27xxx_battery: Cleanup health checking')
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If either twl4030_charger or twl4030_madc is configured as MODULE,
we get build (link) errors.
To solve, the direct call of twl4030_get_madc_conversion() is replaced
by a call to iio_read_channel_processed().
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bb ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds support for the tps65217 charger driver. This driver is
responsible for controlling the charger aspect of the tps65217 mfd.
Currently, this mainly consists of turning on and off the charger, but
some other features of the charger can be supported through this driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
"state" is a bool so it's never less than zero. The intent was to test
"ret" instead.
Fixes: 56d7df8716 ('power: Add Qualcomm SMBB driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit b68c316143 (bq2415x_charger: Allow to load and use driver even if
notify device is not registered yet) introduced null pointer dereference in
case bq is NULL. This patch fixes it.
Fixes: b68c316143 ("bq2415x_charger: Allow to load and use driver even if notify device is not registered yet")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some devices have a pin that can generate an interrupt when
the battery's status changes. Add an interrupt handler to
read the new battery status.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reorganize the logic checking battery health and add under temperature
condition checking.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.
To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix typos and change "relative state of charge" to "state of charge" as not
all supported devices use relative state of charge.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The MODULE_DEVICE_TABLE macro automatically adds all needed
i2c MODULE_ALIASes so remove the extra MODULE_ALIAS.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource function devm_power_supply_register instead
of power_supply_register to simplify the error path by allowing
unregister to happen automatically on error. To be compatible with
the change, replace various gotos by direct returns and remove
unneeded label err.
Also, remove max8998_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove max8903_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
Also, remove max17042_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This diver doesn't applies only on SAM9 SoC families but on SAMA5 families
as well.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91 shutdown
controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
It was not possible to compile at91-poweroff as a module. Implement
.remove() to allow it. Also switch to module_platform_driver_probe() as it
is not hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91 reset
controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
It was not possible to compile at91-reset as a module. Implement .remove()
to allow it. Also switch to module_platform_driver_probe() as it is not
hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since all the at91 platforms are now DT only, at91_reset_platform_probe()
is now useless, remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions devm_request_threaded_irq and
devm_power_supply_register to simplify error handling.
To be compatible with the change, various gotos are replaced
with direct returns and unneeded labels are dropped. Also,
remove pm860x_battery_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the Qualcomm Switch-Mode Battery Charger and Boost driver, found in
pm8941.
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
These drivers already have an I2C device id table that is used to create
module aliases and the used MODULE_ALIAS() was either already in the I2C
table so it was redundant or wasn't a valid I2C id so it was never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
According to lp8727 bindings[*], charging parameter is optional.
So parsing can be skipped in case those properties are undefined.
However, 'debounce-ms' should be read prior to checking the properties.
Otherwise, 'debounce-ms' property will be ignored even it is configured
inside the DT.
So, counting child is processed after updating 'debounce-ms'.
[*] Documentation/devicetree/bindings/power_supply/lp8727_charger.txt
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently, lp8727 charger driver parses the DT and copies values into the
'cl->dev.platform_data' if 'of_node' exists.
This may have architectural issue. Platform data is configurable through
the DT or I2C board info inside the platform area.
However, lp8727 driver changes this configuration when it is loaded.
The driver should get data from the platform side and use the private
data, 'lp8727_chg->pdata' instead of changing the original platform data.
_probe() procedure is changed as follows.
1. lp8727_parse_dt() returns the pointer of lp8727_platform_data.
The driver uses this allocated platform data. So it should keep
original platform data, 'dev->platform_data'.
2. In _probe(), check the return value of lp8727_parse_dt().
If an error is found, then exit as PTR_ERR(pdata).
3. If 'of_node' is not found, then the driver just gets the platform data
from the I2C device structure.
4. Map the platform data to private data structure.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds a driver for the usb power_supply bits of the axp20x PMICs.
I initially started writing my own driver, before coming aware of
Bruno Prémont's excellent earlier RFC with a driver for this.
My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's
drvier has, so I've copied the code for those from his driver.
Note that the AC-power-supply and battery charger bits will need separate
drivers. Each one needs its own devictree child-node so that other
devicetree nodes can reference the right power-supply, and thus each one
will get its own mfd-cell / platform_device and platform-driver.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
When CONFIG_CHARGER_TWL4030=y and CONFIG_TWL4030_MADC=m we get a
compile error:
drivers/built-in.o: In function `twl4030_charger_update_current':
twl4030_charger.c:(.text+0x504681): undefined reference to
`twl4030_get_madc_conversion'
Use IS_REACHABLE to fix it.
Cc: NeilBrown <neil@brown.name>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Revert commit 3fc3895e4f, since
it introduced a boot failure on some OMAP platforms.
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver model
list maintained for the class devices for regulators which will make the
code smaller and avoid some potential bugs. Otherwise another fairly
quiet release for the regulator API, highlights include:
- A new API for setting voltages based on a minimum, target, maximum
triplet.
- Support for continuous voltage ranges rather than tables of explicit
steps in the PWM regulator, requiring less explicit configuration.
- New driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV5DCWAAoJECTWi3JdVIfQDgYH/3mNwtRcwslt8M1L8lzRVyf1
gRrJY5r4EUOcqqsLnQvDHdjgO2yowEolEd3Hd/GElZqzeFgwXaQ62kHwgqnvOt9k
O0l99FbU6ECpB56tSENrV1lfvBTlld9bEhq9NhxvNiWAdpGPqIcjvXfSH28GssJ0
NGr4Yt/A1DG6GsOWxKSODX56WJXJn4emKx3vHH+leUClNWwQVK6JunTmj5IPKLxW
K94Ke41L3JgAy18TLqvFNlTAC22QaHFaM8ul9v7gnPW+S8Bx15MCQz16rMkGViZV
c/DyCu69qCVFLI1svRrvB5oq700QT0GT6jANCVmw+CrkIkESwjS39kX861H6hk8=
=vrVx
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver
model list maintained for the class devices for regulators which will
make the code smaller and avoid some potential bugs.
Otherwise another fairly quiet release for the regulator API,
highlights include:
- a new API for setting voltages based on a minimum, target, maximum
triplet
- support for continuous voltage ranges rather than tables of
explicit steps in the PWM regulator, requiring less explicit
configuration
- new driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM"
* tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (70 commits)
regulator: mt6311: fix platform_no_drv_owner.cocci warnings
regulator: ltc3589: Remove unnecessary MODULE_ALIAS()
regulator: ad5398: Remove unnecessary MODULE_ALIAS()
regulator: pfuze100: Remove unnecessary MODULE_ALIAS()
regulator: core: use debug level print in regulator_check_drms
regulator: lp872x: handle error case
regulator: lp872x: use the private data instead of updating I2C device platform data
regulator: isl9305: Export OF module alias information
regulators: max77693: register driver earlier to avoid deferred probe
regulator: qcom_smd: Set n_voltages for pm8941_lnldo
regulator: core: Use IS_ERR_OR_NULL()
regulator: core: Define regulator_set_voltage_triplet()
regulator: Regulator driver for the Qualcomm RPM
regulator: pbias: Fix broken pbias disable functionality
regulator: core: Spelling fix
regulator: core: Use class device list for regulator_list in late init
regulator: core: Move more deallocation into class unregister
regulator: core: Reduce rdev locking region when releasing regulator
Input: Remove the max77843 haptic driver
Input: max77693: Add support for Maxim 77843
...
Driver bq2415x_charger works also without notify power supply device for
charger detection. But when charger detection is specified in DT, then
bq2415x_charger refused to loaded with -EPROBE_DEFER.
This patch rewrites code so that notify device for charger detection is
checked when power supply event is received and not when registering power
supply device. So this patch allows to use bq2415x_charger driver also when
kernel is compiled without driver for notify power supply device.
Now after this patch scheduled workqueue is called after INIT_DELAYED_WORK,
so it also fix problem when scheduled workqueue was called before init.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds the necessary data for handling io voltage domains on the rk3368.
As interesting tidbit, the rk3368 contains two separate iodomain areas.
One in the regular General Register Files (GRF) and one in PMUGRF in the
pmu power domain.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The rockchip io-domain driver currently only depends on ARCH_ROCKCHIP
itself. This makes it possible to select the power-domain driver, but
not the POWER_AVS class and results in the iodomain-driver not getting
build in this case.
So add the additional dependency, which also results in the driver
config option now being placed nicely into the AVS submenu.
Fixes: 662a958638 ("PM / AVS: rockchip-io: add driver handling Rockchip io domains")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can only use the madc to check for 'ac' availability if the madc has
been compiled in. If not: assume always using USB.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neil@brown.name>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Access to the BQ24190's configurable charge type property (none, trickle,
fast) is being masked by an incorrect power_supply_property entry. After
applying this patch a new 'charge_type' property will appear in the
bq24190-charger sysfs folder backed up by getters/setters already
present in the driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The USB Battery Charging spec (BC1.2) suggests a dedicated
charging port can deliver from 0.5 to 5.0A at between 4.75 and 5.25
volts.
To choose the "correct" current voltage setting requires a trial
and error approach: try to draw current and see if the voltage drops
too low.
Even with a configured Standard Downstream Port, it may not be possible
to reliably pull 500mA - depending on cable quality and source
quality I have reports of charging failure due to the voltage dropping
too low.
To address both these concerns, this patch introduce incremental
current setting.
The current pull from VBUS is increased in steps of 20mA every 100ms
until the target is reached or until the measure voltage drops below
4.75V. If the voltage does go too low, the target current is reduced
by 20mA and kept there.
This applies to currents selected automatically, or to values
set via sysfs. So setting a large value will cause the maximum
available to be used - up to the limit of 1.7A imposed by the
hardware.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This allows AC charging to be turned off, much like usb charging.
"continuous" mode is not available though.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.
Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily. Care must be taken not to over-charge.
It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'off' or 'auto' to
/sys/class/power/twl4030_usb/mode
will now enable or disable charging from USB port. Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging. 'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).
If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.
Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 allows control of the incoming current.
Part of this control is a 'CGAIN' setting which doubles
the range for half the precision. This control affects
several different current setting, so all need to be updated
at once when CGAIN is changed.
With this patch, all of these current setting are managed
by the driver, but most are left at their default settings.
The current drawn is set to 500mA if the allow_usb module parameter is
set, and to 100mA otherwise.
More fine control will appear in later patches.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We will need this calculation in other places, so
create functions to map between register value and uA value.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The usb phy driver already determines when VBUS is available,
so repeating the test in the charger driver is pointless duplication.
On probe, process the last event from the phy, and from then on,
do whatever the phy tells us without double-checking.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now that twl4030_bci_probe can safely return -EPROBE_DEFER,
do so when devm_usb_get_phy_by_node returns that error.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drivers using module_platform_driver_probe cannot return
EPROBE_DEFER from the probe function, which makes them rather useless
these days...
Convert to module_platform_driver() so EPROBE_DEFER can be used.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f40
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
For compatibility between board code and DT, set battery name to same value.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant sysfs binary file boundary check while
reading eeprom content from userspace, the check is done on caller
side in fs/sysfs/file.c, if binary attribute size is not zero.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant calculation of left space on eeprom while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant sysfs binary file boundary checks while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions like devm_kasprintf and
devm_power_supply_register in bq24735_charger_probe. To be
compatible with the change, replace various gotos by direct
returns and drop unneeded labels.
Also, remove bq24735_charger_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Including ARM related header file cause build failure
in i386 build because COMILE_TEST also involve building
zx driver. Remove the unnecessary include file.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove space before tab.
Remove unnecessary line continuations.
Add braces to else statement.
Remove unnecessary parentheses.
Remove unneeded blank lines.
Remove unnecessary 'out of memory' message.
Add missing line after declarations.
Change use of printk to pr_err.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix the alignment of function parameters on new lines.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Shorted lines over 80 characters long by reducing tab count.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the manufacturer property to the bq27x00 driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart
directly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make it possible to set the name of the supply from the devicetree.
Like other power supply drivers just use the node name. This makes
the code smaller as well, as it doesn't need to allocate memory to
hold the name and allocate a unique ID.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Final allocations/registrations are now managed by devres.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This simplifies the error paths.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch introduces a new compatible string: "atmel,sama5d3-rstc" and
new reset function for sama5d3 and later chips.
As in sama5d3 or later chips, we don't have to shutdown the DDR
controller before reset. Shutdown the DDR controller before reset is a
workaround to avoid DDR signal driving the bus, but since sama5d3 and
later chips there is no such a conflict.
So in this patch:
1. the sama5d3 reset function only need to write the rstc register
and return.
2. we can remove the code related with sama5d3 DDR controller as
we don't use it at all.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Charging events this patch refers to are:
- charger is connected to/disconnected from the power source
- battery is reconnected to the charger, after it was absent.
When the charger is connected to/disconnected from the power source, CHRVPI
interrupt occurs and PWR_RDY bit is either set or cleared. PWR_RDY bit is
updated after 1-2 seconds CHRVPI interrupt has occurred.
power_supply_changed() should be called after PWR_RDY bit is updated.
/sys/class/power_supply/rt9455-charger/online file displays the value of
PWR_RDY bit.
This way, if the userspace is notified that a charging event has occurred
and the userspace reads /sys/class/power_supply/rt9455-charger/online file,
this file is properly updated when the userspace reads it.
This is the reason why power_supply_changed() is called in
rt9455_pwr_rdy_work_callback(), instead of being called in interrupt
handler.
Since no interrupt is triggered when the battery is reconnected to the
charger, the userspace is never notified that the battery is reconnected.
This is why power_supply_changed() is called in
rt9455_max_charging_time_work_callback(), so that the userspace is notified
that the battery is reconnected.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Caused by commit 843735b788 ("power: axp288_charger: axp288 charger
driver") from the battery tree interacting with commit 046050f6e6
("extcon: Update the prototype of extcon_register_notifier() with enum
extcon") from the extcon tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
* New charger drivers: BQ24257, BQ25890, AXP288, RT9455
* MAX17042 battery: add health & temperature support
* BQ2415x charger: add ACPI support
* misc. fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=192M
-----END PGP SIGNATURE-----
Merge tag 'for-4.2' of git://git.infradead.org/battery-2.6
Pull power supply and reset updates from Sebastian Reichel:
- new charger drivers: BQ24257, BQ25890, AXP288, RT9455
- MAX17042 battery: add health & temperature support
- BQ2415x charger: add ACPI support
- misc fixes and cleanups
* tag 'for-4.2' of git://git.infradead.org/battery-2.6: (32 commits)
power_supply: Correct kerneldoc copy paste errors
wm831x_power: Fix off-by-one at free_irq()
power_supply: rt9455_charger: Fix error reported by static analysis tool
power_supply: bq24257: use flags argument of devm_gpiod_get
power_supply: bq25890: use flags argument of devm_gpiod_get
sbs-battery: add option to always register battery
power: Add devm_power_supply_get_by_phandle() helper function
power_supply: max17042: Add OF support for setting thresholds
power_supply: sysfs: Bring back write to writeable properties
power_supply: rt9455_charger: Check if CONFIG_USB_PHY is enabled
power: reset: gpio-restart: increase priority slightly
power_supply: bq25890: make chip_id int
power_supply: Add support for Richtek RT9455 battery charger
Documentation: devicetree: Add Richtek RT9455 bindings
of: Add vendor prefix for Richtek Technology Corporation
power_supply: 88pm860x_charger: Do not call free_irq() twice
power: bq24190_charger: Change first_time flag reset condition
power: axp288_charger: axp288 charger driver
power: max17042_battery: add HEALTH and TEMP_* properties support
power_supply: Add support for TI BQ25890 charger chip
...
This file depends on Kconfig options all of which are a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: Sebastian Reichel <sre@kernel.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
An error handling in wm831x_power_probe() mistakenly frees a failed-to-
request irq as well as other irqs. I added missing decrement of the loop
counter.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The result of container_of macro cannot be NULL, so there is no need to
check whether info is NULL.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit a22b41a31e ("sbs-battery: Probe should try talking to the
device") introduced a step in probing the SBS battery, that tries to
talk to the device before actually registering it, saying:
this driver doesn't actually try talking to the device at probe
time, so if it's incorrectly configured in the device tree or
platform data (or if the battery has been removed from the system),
then probe will succeed and every access will sit there and time
out. The end result is a possibly laggy system that thinks it has a
battery but can never read status, which isn't very useful.
Which is of course reasonable. However, it is also very well possible
for a device to boot up on wall-power and be connected to a battery
later on. This is a scenario that the driver supported before said patch
was applied, and even easily achieved by booting up with the battery
attached and removing it later on. sbs-battery's 'present' sysfs file
can be used to determine if the device is available or not.
So with automated device detection lacking for now, in some cases it is
possible that one wants to register a battery, even if none are attached
at the moment. To facilitate this, add a module parameter that can be
used to configure forced loading module loading time. If set, the battery
will always be registered without checking the sanity of the connection.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds a resource-managed version of the
power_supply_get_by_phandle() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The commit edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The fix for NULL pointer exception related to calling uevent for not
finished probe caused to set all writeable properties as non-writeable.
This was caused by checking if property is writeable before the initial
increase of power supply usage counter and in the same time using
wrapper over property_is_writeable(). The wrapper returns ENODEV if the
usage counter is still 0.
The call trace looked like:
device probe:
power_supply_register()
use_cnt = 0;
device_add()
create sysfs entries
power_supply_attr_is_visible()
power_supply_property_is_writeable()
if (use_cnt == 0) return -ENODEV;
use_cnt++;
Replace the usage of wrapper with direct call to property_is_writeable()
from driver. This should be safe call during device probe because
implementations of this callback just return 0/1 for different
properties and they do not access any of the driver's internal data.
Fixes: 8e59c7f234 ("power_supply: Fix NULL pointer dereference during bq27x00_battery probe")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If CONFIG_USB_PHY is not enabled, struct notifier_block is not defined and
compilation fails. Therefore, the functions that process USB event
notifications are defined only if CONFIG_USB_PHY is enabled.
There is no need to define these functions if CONFIG_USB_PHY is not
enabled, since no USB notifications are received in this case.
Also, since rt9455_set_boost_voltage_before_boost_mode() function is
called only if USB_EVENT_ID notification is received, this function should
also be defined only if CONFIG_USB_PHY is enabled.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
gpio-restart uses a priority of 128 and currently most soc-level restart
mechanisms use the same - with some exceptions even using 192.
But while the soc-level restarts are provided by the soc itself,
gpio-restarts will most of the time be board-specfic and be used
when some special board condition makes the soc-level restart
only a second choice.
The problem at hand manifested itself on the rk3288-veyron devices.
While the soc-level restart can sucessfully restart all other rockchip
boards I have, the veyron devices use an external restart mechanism that
seems to not only reset the soc but also some external needed components.
With both restart handlers having priority 128 in my tests the soc-specific
variant took precedent in all cases. While it could restart the soc
sucessfully in all cases, firmware then got an issue when talking to an
external component, resulting in the device being put into recovery mode.
So, give the board-specific restart handler a slight push and move it
to priority 129 to make it more important than the generic soc-specific
restart-handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Smatch static checker correctly detected an impossible condition because
chip_id was declared as u8, instead of int:
drivers/power/bq25890_charger.c:843 bq25890_probe()
warn: impossible condition '(bq->chip_id < 0) => (0-255 < 0)'
Also, while at it, fix the return value too.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVaIsMAAoJEIaOsuA1yqREQXQP/2tYG5H2f71mpYAuOKu1KcYi
DnFH5bKgVQZwl+Dafa41B7P40qub7goCULQSmAgErKboHQvzf7GhzbH22jG3cUg+
icowa+pEstXxzcwQGOMVIOZ3jAIQCZFFOizolfAaCHrnYNGwaCKq+5809EdMyXHc
IdYnkYFYdOVGjTPypzoHf8fjpMoCfMx+TLh2ZV4ICj4o5cVXkr9oXNAA8/B/dn+T
MLK02IPmMOVNJs2gYFQSsGYy03YVR+y62jrYXa+bIa1lzYr4v2yx5SymYTcCWMsH
c6szhMxCOoL3CGzONCT52b+ogfpCzefl0HV6yvpAQmRcgbAiRuVt3caq1TBpvMq0
NJVChEfFtOaUR+UGNkBUzh7/CjcVlH8516NQlCIdPemB8HzqBfRMv9MjHsGt1rXC
SHQMQSTOBw2fbdG5zvi06BOO2hCStqXLNCHARJ2Z5YjP7mLrwteO+wYg2FG9zhTp
ShGZlHPqP/U+50WuzorHEpr/pRTJh3LhDlYJ6CBwyd4+vg17PrYYbkf82d9WDEDL
BFH9qe7jfOwZiWHJvNFeHLriKzj/k3i9/DoRaqtm7QwJgafzBz7l+319jvruupnG
8oxhr+gt74uDPIzxWWv+eFOtO+Uu/q8C3dSp0H/0sY4soBELIgf+QtOkwn596rFp
mBLSkru+oEN62IQbTKDK
=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Based on the datasheet found here:
http://www.richtek.com/download_ds.jsp?p=RT9455
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
My static checker detected double free_irq() in pm860x_charger_remove().
Unloading this module always causes a warning. This patch removes the
first redundant free_irq() call.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The initial register reset of BQ24190 generates a charger status change
whose propagation via power_supply_changed is prevented using a flag.
This flag gets never reset so all following events are ignored as well
leading for example to userspace not detecting charger connects/disconnects.
Therefor change the reset condition of first_time flag, so only the
propagation of the first charger status change is prevented.
Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
twl4030_charger currently finds the associated phy
using usb_get_phy() which will return the first USB2 phy.
If your platform has multiple such phys (as mine does),
this is not reliable (and reliably fails on the GTA04).
Change to use devm_usb_get_phy_by_node(), having found the
node by looking for an appropriately named sibling in
device-tree.
This makes usb-charging dependent on correct device-tree
configuration.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds new power supply charger driver support
for X-Power AXP288 PMIC integrated charger.
This driver interfaces with the axp20x mfd driver as a cell
and listens to extcon cable events for setting up charging.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds the support for following battery properties
to max17042 fuel gauge driver.
POWER_SUPPLY_PROP_TEMP_ALERT_MIN
POWER_SUPPLY_PROP_TEMP_ALERT_MAX
POWER_SUPPLY_PROP_TEMP_MIN
POWER_SUPPLY_PROP_TEMP_MAX
POWER_SUPPLY_PROP_HEALTH
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
More details about the chip can be found here:
http://www.ti.com/product/bq25890
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The 'parent' argument passed to power_supply_register() is now used to
postpone callbacks to the driver until the driver's probe end.
Pass current device from charger-manager to utilize that. This will move
created power supply from virtual to platform devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use wrappers over get_property() and set_property() internally in power
supply and for sysfs interface. The wrappers provide safe access if
power supply is not yet registered or t is being destroyed.
In case of syfs the theoretical race could happen between ending of
driver's probe and parallel sysfs access:
some_driver_probe() userspace
==================================== ===========================
drv->psy = power_supply_register()
device_add()
sysfs entries are created
atomic_inc(&psy->use_cnt);
store on sysfs attributes
drv->set_property()
dereference of drv->psy
drv->psy = returned psy;
For leds the race could happen between power supply being destroyed and
ongoing power_supply_changed_work().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
devm_gpiod_get_optional returns NULL if devm_gpiod_get would return an
ENOENT error pointer.
There is no semantic change intended.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace of_property_read_u32() with device_property_read_u32(), which is a
wrapper over ACPI and device tree enumeration methods.
When ACPI enumeration is used, automode is not supported. Therefore,
bq2415x_charger does not update its input current automatically, depending
on the USB port type that is connected to. Input current may be updated via
sysfs.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
"ENOSYS means 'invalid syscall nr' and nothing else"
- remove unnecessary log message
- split lines whose length is greater than 80 characters
- if an arm statement uses braces, add braces to the other arms of the
respective statement, too
- match alignment with open parenthesis
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Based on the datasheet found here:
http://www.ti.com/lit/ds/symlink/bq24257.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Don't call the power_supply_changed() from power_supply_register() when
parent is still probing because it may lead to accessing parent too
early.
In bq27x00_battery this caused NULL pointer exception because uevent of
power_supply_changed called back the the get_property() method provided
by the driver. The get_property() method accessed pointer which should
be returned by power_supply_register().
Starting from bq27x00_battery_probe():
di->bat = power_supply_register()
power_supply_changed()
kobject_uevent()
power_supply_uevent()
power_supply_show_property()
power_supply_get_property()
bq27x00_battery_get_property()
dereference of di->bat which is NULL here
The dereference of di->bat (value returned by power_supply_register())
is the currently visible problem. However calling back the methods
provided by driver before ending the probe may lead to accessing other
driver-related data which is not yet initialized.
The call to power_supply_changed() is postponed till probing ends -
mutex of parent device is released.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Tested-By: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Power supply is often registered during probe of a driver. The
power_supply_register() returns pointer to newly allocated structure as
return value. However before returning the power_supply_register()
calls back the get_property() method provided by the driver through
uevent.
In that time the driver probe is still in progress and driver did not
assigned pointer to power supply to its local variables. This leads to
NULL pointer dereference from get_property() function.
Starting from bq27x00_battery_probe():
di->bat = power_supply_register()
device_add()
kobject_uevent()
power_supply_uevent()
power_supply_show_property()
power_supply_get_property()
bq27x00_battery_get_property()
dereference of (di->bat) which is NULL here
The first uevent of power supply (the one coming from device creation)
should not call back to the driver. To prevent that from happening,
increment the atomic use counter at the end of power_supply_register().
This means that power_supply_get_property() will return -ENODEV.
IMPORTANT:
The patch has impact on this first uevent sent from power supply because
it will not contain properties from power supply.
The uevent with properties will be sent later after indicating that
power supply has changed. This also has a race now, but will be fixed in
other patches.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Tested-By: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Without MODULE_ALIAS bq27x00_battery module won't get loaded automatically.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The Broadcom STB reboot driver depends on MFD_SYSCON, it uses
syscon_regmap_lookup_by_phandle() which will not lookup syscon phandles
if MFD_SYSCON is disabled, and instead will return -ENOSYS since it is
turned into an inline stub.
Fixes: 030494e750 ("power: reset: Add reboot driver for brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The return value of hrtimer_start() tells whether the timer was
inactive or active already when hrtimer_start() was called.
The code emits a bogus warning if the timer was active already
claiming that the timer could not be started.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frans Klaver <frans.klaver@xsens.com>
Cc: "René Moll" <linux@r-moll.nl>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-pm@vger.kernel.org
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In case of error, the function devm_ioremap() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: ecfe64d8c5 ("power: reset: Add AT91 reset driver")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the original author details of the axp288_fuel_gauge driver.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The return value of hrtimer_start() tells whether the timer was
inactive or active already when hrtimer_start() was called.
The code emits a bogus warning if the timer was active already
claiming that the timer could not be started.
Remove it along with the bogus comment in the else path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-pm@vger.kernel.org
Without MODULE_ALIAS twl4030_madc_battery won't get loaded automatically.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Because of added iio error handling private data allocation was converted
to managed to simplify code.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Reviewed-By: Sebastian Reichel <sre@debian.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch add missed blank line after decalations.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently, max17042 battery driver choose register map by MAX17042_DevName
register. But it is return IC specific firmware version. So other maxim chip
hard to use this drvier. This patch choose chip type from driver_data.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix the passing of big endian data to routines that will be writing
it to the bus in the wrong order.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If power_supply_register() fails do not dereference returned ERR_PTR.
The pointer was dereferenced to print name of battery which registration
failed. Instead use the name from the power supply description passed to
the power_supply_register() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[for vexpress]
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes:
drivers/power/reset/rmobile-reset.c: In function ‘rmobile_reset_probe’:
drivers/power/reset/rmobile-reset.c:61:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sysc_base2);
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Do not put reference to power supply in early exit paths of
pm860x_done_handler() because:
1. it is not yet initialized,
2. it is NULL.
This fixes possible NULL pointer dereference and following build
warning:
drivers/power/88pm860x_charger.c: In function ‘pm860x_done_handler’:
drivers/power/88pm860x_charger.c:516:18: warning: ‘psy’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Additionally this puts the power supply reference before unlocking
mutex. This actually is not needed (there is no race here) but has
logical sense and makes the exit paths cleaner.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use power_supply_put() to decrement the power supply's device reference
counter (increased by power_supply_get_by_name() or
power_supply_get_by_phandle()).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use power_supply_put() to decrement the power supply's device reference
counter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use power_supply_put() to decrement the power supply's device reference
counter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Increment the power_supply.use_cnt usage counter on:
- power_supply_get_by_phandle()
- power_supply_get_by_name()
and decrement it on power_supply_put() call.
This helps tracking of valid usage of power supply instance by
consumers. The usage counter itself also allows safe calling of
power_supply_get_property-like functions even when driver unregisters
this power supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power_supply_get_by_phandle() and power_supply_get_by_name() use
function class_find_device() for obtaining the reference to power
supply. Each use of class_find_device() increases the power supply's
device reference counter.
However the reference counter was not decreased by users of this API.
Thus final device_unregister() call from power_supply_unregister() could
not release the device and clean up its resources. This lead to memory
leak if at least once power_supply_get_by_*() was called between
registering and unregistering the power supply.
Add and document new API power_supply_put() for decrementing the
reference counter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
- set_property -> power_supply_set_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
- set_property -> power_supply_set_property
- property_is_writeable -> power_supply_property_is_writeable
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add simple wrappers for accessing power supply's function attributes:
- get_property -> power_supply_get_property
- set_property -> power_supply_set_property
- property_is_writeable -> power_supply_property_is_writeable
- external_power_changed -> power_supply_external_power_changed
This API along with atomic usage counter adds a safe way of accessing a
power supply from another driver. If power supply is unregistered after
obtaining reference to it by some driver, then the API wrappers won't be
executed in invalid (freed) context.
Next patch changing the ownership of power supply class is still needed
to fully fix race conditions in accessing freed power supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.
The power_supply_register() function is changed so all power supply
drivers need updating.
When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.
When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
[for drivers/hid/*]
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Allow drivers to store private data inside power_supply structure for
later usage in power supply operations.
Usage of driver private data is necessary to access driver's state
container object from power supply calls (like get_property()) if struct
'power_supply' is a stored there as a pointer, for example:
struct some_driver_info {
struct i2c_client *client;
struct power_supply *power_supply;
...
}
In such case one cannot use container_of() and must store pointer to
state container as private data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The POWER_SUPPLY_PROP_STATUS case in gab_get_property() wasn't providing any
value.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
All 5 IRQ handlers of the driver are requested as threaded interrupt
handlers. However, only 1 handler can block. The remaining 4 handlers
defer the actual handling to a workqueue. Hence, 4 of 5 IRQ handlers
have a considerable overhead, since they are executed in a kernel thread
to schedule another kernel thread (workqueue).
This change splits up the 5 interrupt handlers into top halves (_th) and
bottom halves (_bh) and resolves the aforementioned overhead by only
requesting threaded interrupts (i.e., bottom halves) when necessary.
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
New power_supply driver at driver/power which interfaces with the
axp20x mfd driver as a cell. Provides battery info, monitors for
changes, and generates alerts on temperature and capacity issues
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds bq24157s charger in the list of supported chargers.
bq24157s is similar to bq24158, except for Bit6 from Special Charger
Voltage/Enable Pin Status register, but this register is currently
not used by bq2415x_charger.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix coding style to comply with checkpatch.pl
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request may fail.
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for bq27510 to the bq27x00 driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Using devm_power_supply_register allows the unregister to happen
automatically on error or final put.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Converting jiffies to milliseconds by "val * 1000 / HZ" is technically
OK but jiffies_to_msecs(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API consolidation only and
should make things more readable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. as
timeout is used for wait_for_completion_timeout exclusively here its
type is simply changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Simplify a little ab8500_fg_sysfs_psy_create_attrs () and
ab8500_fg_sysfs_psy_remove_attrs() functions because they received
pointer to power supply device which was then converted into power
supply instance. Then it was converted into struct ab8500_fg. The path
looked like:
ab8500_fg->psy.dev -> psy -> ab8500_fg
Instead just pass pointer to struct ab8500_fg directly so all
conversions won't be necessary.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Driver forgot to unregister charger power supply if registering of
battery supply failed in probe(). In such case the memory associated
with power supply leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The return values of create_singlethread_workqueue() and
power_supply_register() calls were not checked and even on error probe()
function returned 0.
1. If allocation of workqueue failed (returning NULL) then further
accesses could lead to NULL pointer dereference. The
queue_delayed_work() expects workqueue to be non-NULL.
2. If registration of power supply failed then during unbind the driver
tried to unregister power supply which was not actually registered.
This could lead to memory corruption because
power_supply_unregister() unconditionally cleans up given power
supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 00a588f9d2 ("power: add driver for battery reading on iPaq h3xxx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Driver allocates singlethread workqueue in probe but it is not destroyed
during removal.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 00a588f9d2 ("power: add driver for battery reading on iPaq h3xxx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.
This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: da0a00ebc2 ("power: Add twl4030_madc battery driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Consolidate regmap_read() and regmap_write() into one
regmap_update_bits() call. This is more readable and safer because
regmap's mutex will prevent any concurrent access to modified registers
(the concurrent access could happen through max17042_init_chip() in
scheduled work).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The scheduled work in max17040_battery driver reads device parameters
and stores them in memory. Any CPU could do that so use system efficient
workqueues to limit unnecessary CPU wake ups.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Re-work and fix handling of errors when retrieving power supply
properties:
1. Return errno values directly from get_property() instead of
storing 'unknown' as intval for given property.
2. Handle regmap_read() errors and return errno code. Previously the
regmap_read() return code was ignored so an uninitialized value from
the stack could be used for calculating the property.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove caching of charging and battery states in driver's state
container because the cached value was not used later.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Re-work and fix handling of errors when retrieving power supply
properties:
1. Return errno values directly from get_property() instead of storing
'unknown' as intval for given property.
2. Handle regmap_read() errors when getting 'online' and 'present'
proprties and return errno code. Previously the regmap_read() return
code was ignored so an uninitialized value from the stack could be
used for calculating the property.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use subdir-ccflags-* instead of ccflags-* to inherit the debug
settings from Kconfig when traversing subdirectories.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
power_supply status changes for the bq27x00 are only
noticed via polling, not via interrupts. So they are never
the source of events which should reliably wake the system
from suspend.
So it is appropriate to register as a no_ws power source,
just like the ACPI battery.
This removes some debugging messages which occasionally
confusingly identify bq27x00 as a wakeup source.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds support for DA9150 Charger & Fuel-Gauge IC Charger.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The driver reported 30% less than actually measured. This turned out to
be caused by a simple typo in the formula to calculate the LSB quantity.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The driver reported 30% less than actually measured. This turned out to
be caused by a simple typo in the formula to calculate the LSB quantity.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Driver forgot to unregister power supply if request_threaded_irq()
failed in probe(). In such case the memory associated with power supply
leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: a830d28b48 ("power_supply: Enable battery-charger for 88pm860x")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver is now arm specific anymore, so there is no need to include
an arm specific include file. Also drop unnecessary depencency on ARM
from Kconfig.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The st-poweroff driver does not really power off the system
but resets it, so Kconfig should not claim that the driver
would handle power-off.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart
directly. Select high priority since the restart handler is instantiated
through devicetree, indicating that it should be used if configured.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
sun6i restart is now handled by its watchdog driver directly,
so this driver is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart
directly. Register with high priority since the driver unconditionally
overwrites other restart handlers if instantiated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart
directly. Select high priority since the restart handler is instantiated
through devicetree, indicating that it should be used if configured.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace hard-coded numbers for indices of power supply array with enum.
This improves a little the readability as one does not have to guess
which power supply is associated with number.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Both the LTC2941 and LTC2943 measure battery capacity.
The LTC2943 is compatible with the LTC2941, it adds voltage and
temperature monitoring, and uses a slightly different conversion
formula for the charge counter.
To avoid confusion with e.g. the LTC2945, the driver is called
LTC2941 instead of LTC294X.
v2: Fix units of measurement: uV, uA and centidegrees.
v3: Correctly set configuration register. Allow negative values
for the sense resistor.
v4: Run checkpatch.pl and fix all errors and warnings.
v5: Prefix "lltc," to devicetree properties.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[ removed .owner field ]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The register bit fields are a little different, so add an entry and a
compatible string to accommodate them.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some of the older chips used different bits to arm and trigger the reset.
Add the infrastructure needed to specify this through the "compatible"
string.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now that the driver doesn't use any ARM-specific headers, it is safe
to build on MIPS or with COMPILE_TEST.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
To guerantee proper charing and managing batteries even in suspend,
charger-manager has used rtc device with rtc framework interface.
However, it is better to use alarmtimer for cleaner and more appropriate
operation.
This patch makes driver to use alarmtimer for polling work in suspend and
removes all deprecated codes related with using rtc interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
at91_poweroff_get_wakeup_mode can return a negative error code and should
therefore not return an enum type. Similar, its result should not be
assigned to an enum type. Otherwise, the returned value is never negative,
resulting in a compiler warning and a missed error condition, which in turn
results in writing bad values into a chip register.
Also fix other compiler warnings which can be easily avoided.
drivers/power/reset/at91-poweroff.c:74:24:
warning: type qualifiers ignored on function return type
drivers/power/reset/at91-poweroff.c:74:24:
warning: no previous prototype for 'at91_poweroff_get_wakeup_mode'
drivers/power/reset/at91-poweroff.c:83:16:
warning: comparison between signed and unsigned integer expressions
drivers/power/reset/at91-poweroff.c:97:2:
warning: comparison of unsigned expression < 0 is always false
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In current driver, power_supply_changed() is called whenever any of
the battery attribute changed. This causes kernel to increases the
'/sys/power/wakeup_count' and make suspend not working correctly.
This patch change this behavior to call power_supply_changed()
only when the battery capacity changed.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: David Riley <davidriley@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
- SOC is at 0x1C so we must add 0x4 as stated in the comment to read the
right value.
- DCAP is at 0x3c so we also must use a value with the right offset to get
the correct design capacity.
Actually testing on a bq27410 which has the same register map as bq27425
(but adds new registers).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This is only a small clean-up. The driver can be built without SYSFS
as there exist stubs for used functions.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fixes following build warning:
In file included from include/linux/printk.h:261:0,
from include/linux/kernel.h:13,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/power/bq24190_charger.c:11:
drivers/power/bq24190_charger.c: In function ‘bq24190_irq_handler_thread’:
include/linux/dynamic_debug.h:86:20: warning: ‘ss_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
drivers/power/bq24190_charger.c:1211:5: note: ‘ss_reg’ was declared here
u8 ss_reg, f_reg;
^
In file included from include/linux/printk.h:261:0,
from include/linux/kernel.h:13,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/power/bq24190_charger.c:11:
include/linux/dynamic_debug.h:86:20: warning: ‘f_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
drivers/power/bq24190_charger.c:1211:13: note: ‘f_reg’ was declared here
u8 ss_reg, f_reg;
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a reset driver for Renesas R-Mobile and SH-Mobile SoCs. It registers
a restart handler to trigger a soft power-on reset through the R-Mobile
System Controller.
The priority of this restart handler is 192, to allow a watchdog driver
to use priority 128.
Note that we do not use syscon-reboot, as the HPB (Peripheral Bus
Bridge) semaphore should be acquired on systems where both the ARM and
SH core are in use. The driver can be extended later to support this,
when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove the function ab8500_fg_reinit() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
drivers/power/max77693_charger.c:747:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
drivers/power/max77693_charger.c:615:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new driver for Maxim 77693 switch-mode charger (part of max77693
MFD driver) providing power supply class information to userspace.
The charger has +20V tolerant input. Current input can be set from 0 to
2.58 A. The charger can deliver up to 2.1 A to the battery or 3.5 A to
the system (when supplying additional current from battery to system).
The driver is configured through DTS (battery and system related
settings) and sysfs entries (timers and top-off charging threshold).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The driver mismatched 'num_supplicants' with 'num_supplies' of
power_supply structure.
It provided list of supplicants (power_supply.supplied_to) but did
not set the number of supplicants. Instead it set the num_supplies which
is used when iterating over number of supplies (power_supply.supplied_from).
As a result the list of supplicants was ignored by core because its size
was 0.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: d7bf353fd0 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Teach collie_battery driver to communicate to the kernel that it can
generate wakeup events. Handle enabling/disabling wakeup on battery full
event in suspend/resume callbacks.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
enable_irq_wakeup returns 0 in case it correctly enabled the IRQ to
generate the wakeup event (and thus resume should call disable_irq_wake).
Currently gpio-charger driver has this logic inverted. Correct that thus
correcting enable/disable_irq_wake() calls balance.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds device driver of Richtek PMIC.
The driver support battery fuel gauge. Fuel gauge calculates and determines the
battery state of charge (SOC) according to battery open circuit voltage (OCV).
Also, this driver provides battery average voltage, voltage and battery present
property.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently the ltc2952 supports only one button sequence to initiate
powerdown. This is not always desirable, as even prolonged button
presses can happen in use.
Allow ltc2952 users to pick their own power down sequence, by making the
trigger input optional. Since this still means that the ltc2952 may
power down the platform if the power button is pressed for about 5
seconds, we still need to make sure to start the watchdog toggle to
prolong the system power for as long as we need it.
This will still allow the system to control power using the kill signal.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In ltc2952_poweroff_handler it is theoretically possible that the timer
fails to start on first pass (button press), but succeeds in starting on
the second (button release). This will cause the button press to be
misinterpreted, and will incorrectly shut down the system. Because a
picture says more than a thousand words:
Expected behavior:
tmr: ++++++++++
btn: -----__________-----
Faulty behavior:
tmr: +++++
btn: -----__________-----
Legend:
+ timer runs
_ button pressed
- button depressed
To prevent this from happening, check the value of the gpio before
starting the timer. If the button is active, we should start the timer,
else we should stop it.
The situation described can now still occur if the polarity of the input
pin is set incorrectly, but that at least is predictable behavior and
can be detected during the first tests.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Disable the timers when ltc2952_poweroff is removed. We don't want to
risk calling functions on data that no longer exist.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The function pointers for the timers and pm_power_off are assigned with
C++ style
foo = &func;
Let's change it instead to the more C style
foo = func;
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
ltc2952_poweroff_handler uses gotos to return from the function. Since
we don't do cleanups exiting this function, just return IRQ_HANDLED on
the spot and be done with it.
While at it, remove the variable 'ret'. It was never used very much.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Documentation/SubmittingDrivers suggests these be implemented even when
they do nothing. On the other hand, the platform code calls these
functions 'legacy'. Suspend and resume operations should go into a
pm_ops structure, pointed at by the driver's pm field. This approach
would lead to a lot of boiler plate, while achieving nothing. Drop the
functions instead.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
As per Documentation/CodingStyle ch.4, we should keep global variables
to a mininum. Move the panic state into the driver data, regardless of
whether panic is a system state or not.
This removes the need for the custom _init and _exit functions, so
replace them with a call to the module_platform_driver() macro.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Documentation/CodingStyle ch.4 mentions in a side node that global
variables should only be used if you really need them. Reduce the use of
the global instance of ltc2952_poweroff so we may eventually remove it
entirely.
While at it, rename ltc2952_poweroff_data to ltc2952_poweroff, just to
save that little bit of typing.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The three gpio's used by this driver are stored in an array of pointers.
This doesn't add much besides cleanups in a loop. In fact, it makes most
of the usage sites harder to read. Unroll the loop, and live with the
fact that cleanups become slightly larger.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make use of the fact that we allocated resources can be automatically
deallocated. This reduces cleanup code and chance of errors. It also
removes the need for the virq member of the ltc2952_poweroff_data
struct.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make use of the fact that the allocated resources can be automatically
deallocated. This reduces cleanup code and chance of leaks.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Augment the Versatile reset driver to also handle the core
module reset sequence used on the Integrator/AP and
Integrator/CP.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
* update power/reset drivers to use kernel restart handler
* add power off driver for i.mx6
* add DT support for gpio-charger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v7l/
-----END PGP SIGNATURE-----
Merge tag 'for-v3.19' of git://git.infradead.org/battery-2.6
Pull power supply updates from Sebastian Reichel::
"Power supply and reset changes for the v3.19 series
- update power/reset drivers to use kernel restart handler
- add power off driver for i.mx6
- add DT support for gpio-charger"
* tag 'for-v3.19' of git://git.infradead.org/battery-2.6:
power: reset: adjust priority of simple syscon reboot driver
power: ds2782_battery: Simplify the PM hooks
power/reset: brcmstb: Register with kernel restart handler
power/reset: hisi: Register with kernel restart handler
power/reset: keystone: Register with kernel restart handler
power/reset: axxia: Register with kernel restart handler
power/reset: xgene: Register with kernel restart handler
power/reset: xgene: Use mdelay instead of jiffies based timeout
power/reset: xgene: Use local variable dev instead of pdev->dev
power/reset: xgene: Drop devm_kfree
power/reset: xgene: Return -ENOMEM if out of memory
power/reset: vexpress: Register with kernel restart handler
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
power: gpio-charger: add device tree support
dt-bindings: document gpio-charger bindings
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME within #ifdef blocks depending on
CONFIG_PM may be dropped now.
Do that in drivers/power/pm2301_charger.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Currently, all restart handler use the priority 128, including
watchdogs. Probably most SoC have a watchdog, and some of them
register it also as a restart handler. But if a SoC specifies
a dedicated reboot capability using this syscon driver, this is
usually the preferred reboot method. Hence, raise the priority
of this driver to 192.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SIMPLE_DEV_PM_OPS() macro already takes care of the CONFIG_PM_SLEEP=n case,
so we can simplify the code a little bit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart directly.
Move notifier registration to the end of the probe function to avoid having to
implement error handling.
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Register with kernel restart handler instead of setting arm_pm_restart directly.
This patch also addresses the following compile warning.
drivers/power/reset/xgene-reboot.c: In function 'xgene_reboot_probe':
drivers/power/reset/xgene-reboot.c:77:17: warning:
assignment from incompatible pointer type [enabled by default]
The warning was due to a mismatch between the type of arm_pm_restart
and the restart function.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
jiffies are not running at this stage of system shutdown, meaning an
error in the reset function would never be reported. Replace with mdelay().
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using a local variable dev to point to the device is simpler then repeatedly
dereferencing pdev->dev.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is customary to return an error code of -ENOMEM if the system
is out of memory. Also, in that case, the infrastructure will report
an error, so it is unnecessary to report it again.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the kernel restart handler instead of setting arm_pm_restart directly.
This allows for more than one restart handler in the system.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the ability to parse gpio-charger data from a devicetree node.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Andreas Dannenberg