This patch sets and clears FCF_ASYNC_{SENT|ACTIVE} flags to prevent
stalling of relogin attempt. Once flag are correctly set/cleared, relogin
timer can retry relogin attempt for driver to continue login.
Fixes: fa83e65885 ("scsi: qla2xxx: ensure async flags are reset correctly")
Cc: stable@vger.kernel.org #4.17
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix race condition between switch cmd completion and timeout timer. Timer
has popped triggers command free. On IOCB completion, stale sp point was
reused. Instead, an abort will be sent to FW to nudge the command out of FW
where the normal completion will take place.
RIP: 0010:qla2x00_chk_ms_status+0xf3/0x1b0 [qla2xxx]
Call Trace:
<IRQ>
qla24xx_els_ct_entry.isra.15+0x1d4/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x39/0xf0 [qla2xxx]
qla24xx_process_response_queue+0xbc/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x8a/0xf0 [qla2xxx]
__handle_irq_event_percpu+0xa0/0x1f0
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After selecting the NPort handle/loop_id, set a bit in the loop_id_map to
prevent others from selecting the same NPort handle.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Flush pending mailbox commands on chip reset. Wake up command that's
waiting for an interrupt and wait for mailbox counters to go to zero.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During normal IO, FW can return IO with 'port unavailble' status. Driver
would send a LOGO to remote port for session resync. On an off chance, a
PLOGI could arrive before sending the LOGO. This patch will skip sendiing
LOGO if a PLOGI just came in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets discovery state back to GNL (Get Name List) when session is
stuck at GPDB (Get Port DataBase). This will allow state machine to retry
login and move session state ahead in discovery.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent multiple registrations with transport layer for the same remote
port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses shadow pointer instead of Mirror pointer for firmware dump
collection. Skip those entries for Mirror pointers for Request/Response
queue from firmware dump template reading.
Following messages are printed in log messages:
qla27xx_fwdt_entry_t268: unknown buffer 4
qla27xx_fwdt_entry_t268: unknown buffer 5
This patch fixes these error messages by adding skip_entry() to not read
them from template.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent user from sending commands through sysfs while firmware is not
running or reset is in progress.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_reset_active only covers the window of turning the chip off. Add
check to cover turning chip on.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login retry count was not properly decrementing which lead to endless
retry.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of N2N connect, sg_reset for bus/device/host was causing driver and
firmware state to go out of sync. This patch fixes this link instablity
when reconnect is attempted after link flap.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables scriptb0 and dp_sgmin are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable]
warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Updates csio_get_flash_params() to take care of ISSI, Macronix and
Winbond FLASH parts.
- Assume flash part size to be 4MB if it cannot be identified
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A long time ago the unfortunate decision was taken to add a self-deletion
attribute to the sysfs SCSI device directory. That decision was unfortunate
because self-deletion is really tricky. We can't drop that attribute
because widely used user space software depends on it, namely the
rescan-scsi-bus.sh script. Hence this patch that avoids that writing into
that attribute triggers a deadlock. See also commit 7973cbd9fbd9 ("[PATCH]
add sysfs attributes to scan and delete scsi_devices").
This patch avoids that self-removal triggers the following deadlock:
======================================================
WARNING: possible circular locking dependency detected
4.18.0-rc2-dbg+ #5 Not tainted
------------------------------------------------------
modprobe/6539 is trying to acquire lock:
000000008323c4cd (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x45/0x90
but task is already holding lock:
00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&shost->scan_mutex){+.+.}:
__mutex_lock+0xfe/0xc70
mutex_lock_nested+0x1b/0x20
scsi_remove_device+0x26/0x40 [scsi_mod]
sdev_store_delete+0x27/0x30 [scsi_mod]
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x190/0x230
__vfs_write+0xd2/0x3b0
vfs_write+0x101/0x270
ksys_write+0xab/0x120
__x64_sys_write+0x43/0x50
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&shost->scan_mutex);
lock(kn->count#202);
lock(&shost->scan_mutex);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by modprobe/6539:
#0: 00000000efaf9298 (&dev->mutex){....}, at: device_release_driver_internal+0x68/0x360
#1: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
stack backtrace:
CPU: 10 PID: 6539 Comm: modprobe Not tainted 4.18.0-rc2-dbg+ #5
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_circular_bug.isra.34+0x213/0x221
__lock_acquire+0x1a7e/0x1b50
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
See also https://www.mail-archive.com/linux-scsi@vger.kernel.org/msg54525.html.
Fixes: ac0ece9174 ("scsi: use device_remove_file_self() instead of device_schedule_callback()")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.6
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enablement of the PBDE optimization brought out some incompatible behaviors
under error scenarios.
Best to disable and remove the PBDE optimization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After memory allocation for the LCB response frame, the memory wasn't zero
initialized, and not all fields are set. Thus garbage shows up in the
payload.
Fix by zeroing the memory at allocation. Also properly set the Capability
field based on duration support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During remote port loss fault testing, the driver crashed with the
following trace:
general protection fault: 0000 [#1] SMP
RIP: ... lpfc_nvme_register_port+0x250/0x480 [lpfc]
Call Trace:
lpfc_nlp_state_cleanup+0x1b3/0x7a0 [lpfc]
lpfc_nlp_set_state+0xa6/0x1d0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x213/0x440
lpfc_disc_state_machine+0x7e/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x18a/0x200 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x3b5/0x6f0 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x161/0x240 [lpfc]
lpfc_work_done+0x948/0x14c0 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc9/0xe0
ret_from_fork+0x55/0x80
After registering a new remoteport, the driver is pulling an ndlp pointer
from the lpfc rport associated with the private area of a newly registered
remoteport. The private area is uninitialized, so it's garbage.
Correct by pulling the the lpfc rport pointer from the entering ndlp point,
then ndlp value from at rport. Note the entering ndlp may be replacing by
the rport->ndlp due to an address change swap.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enabling list_debug showed the drivers txcmplq was suffering list
corruption. The systems will eventually crash because the iocb free list
gets crossed linked with the prings txcmplq. Most systems will run for a
while after the corruption, but will eventually crash when a scsi eh reset
occurs and the txcmplq is attempted to be flushed. The flush gets stuck in
an endless loop.
The problem is the abort handler does not hold the sli4 ring lock while
validating the IO so the IO could complete while the driver is still
preping the abort. The erroneously generated abort, when it completes, has
pointers to the original IO that has already completed, and the IO
manipulation (for the second time) corrupts the list.
Correct by taking the ring lock early in the abort handler so the erroneous
abort won't be sent if the io has/is completing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CNA ports were showing speed as "unknown" even if the link is up.
Add speed decoding for FCOE-based adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts the drivers that called transport_deregister_session_configfs
and then immediately called transport_deregister_session to use
target_remove_session.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename target_alloc_session to target_setup_session to avoid confusion with
the other transport session allocation function that only allocates the
session and because the target_alloc_session does so much more. It
allocates the session, sets up the nacl and registers the session.
The next patch will then add a remove function to match the setup in this
one, so it should make sense for all drivers, except iscsi, to just call
those 2 functions to setup and remove a session.
iscsi will continue to be the odd driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that building with W=1 causes the compiler to
complain about fall-through.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that sparse reports the following:
drivers/scsi/libiscsi.c:1844:23: warning: context imbalance in 'iscsi_exec_task_mgmt_fn' - unexpected unlock
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is motivated by a response in the thread:
Re: [PATCH 0/5]stop normal completion path entering a timeout req
by Jianchao Wang . It generalizes the error injection of
blk_abort_request() to use scsi_debug's "every_nth" mechanism. Ref with
original patch to scsi_debug:
https://lore.kernel.org/lkml/a68ad043-26a1-d3d8-2009-504ba4230e0f@oracle.com/
Also convert two vmalloc/memset(0) to vzalloc() calls.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tw_probe() returns 0 in case of fail of tw_initialize_device_extension(),
pci_resource_start() or tw_reset_sequence() and releases resources.
twl_probe() returns 0 in case of fail of twl_initialize_device_extension(),
pci_iomap() and twl_reset_sequence(). twa_probe() returns 0 in case of
fail of tw_initialize_device_extension(), ioremap() and
twa_reset_sequence().
The patch adds retval initialization for these cases.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tscam(), atp870_init(), atp880_init() and atp885_init() are never
called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
wait_chip_ready() and wait_firmware_ready() are never called in atomic
context. They call mdelay() to busy wait which is not necessary. mdelay()
can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The null checks on nvmebuf are redundant as nvmebuf is always obtained from
a container_of() and hence can never be null. Remove all the redundant null
checks. This also cleans up a static analysis warning.
Detected by CoverityScan, CID#1471753 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Generated by scripts/coccinelle/misc/strncpy_truncation.cocci
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a check ERR bit of status to decide whether there is something wrong
with initial register-D2H FIS. If error exist, PHY link reset the channel
to restart OOB.
Directly call work HISI_PHYE_LINK_RESET replacing disable_phy_vx_hw() and
enable_phy_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In task start delivery function, we need to add a memory barrier to prevent
re-ordering of reading memory by hardware. Because the slot data is set in
task prepare function and it could be running in another CPU.
This patch adds an memory barrier after s->ready is read in the task start
delivery function, and uses WRITE_ONCE() in the places where s->ready is
set to ensure that the compiler does not re-order.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To decrease the usage of spinlock during delivery IO, relocate some code in
hisi_sas_task_prep().
Also an invalid comment is removed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements handlers of PCIe FLR for v3 hw, reset_prepare() and
reset_done().
User can issue FLR through sysfs interface, as v3 hw support PCIe FLR.
Then if we don't implement these two handlers, our SAS controller will not
work after executing FLR.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Much code of PM suspend function also exists in soft reset function. This
is not concise. So, this patch relocates the common code of these two
functions to a separate function.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch tidies host controller reset function by putting some code to
two new functions, and exports these two functions out, so that they could
be used by FLR feature to be realised.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an issue that link reset can't recover PHY when STP link timeout.
Because current process of enabling PHY for v3 hw will wait last
transmission done. The time of one transmission depends IO size, disk model
and so on. Normally, it should be shorter than 50ms. But the last
transmission could be never done for some abnormal scenarios, such as STP
link timeout.
This patch is to fix the issue. Check PHY status after starting process of
enabling PHY for 50ms. If the PHY is still active, we disable it forcibly
by PHY reset. Of course, we need to clear the PHY reset bit when enable
PHY.
Besides, the function disable_phy_v3_hw() should not be suitable to call in
interrupts for hilink bug for this 50ms delay. Then, we do link reset for
hilink bug directly. The change is that we don't clear the invalid dword
count register. This is better. Because we should not clear such error
count while not saved.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ISR of channel interrupt of v3 hw is a little long and messy. This
patch tidies it by relocating CHL_INT1 and CHL_INT2 handling to new
function separately.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For some time now we have not used hisi_sas_slot_abort() to handle erroring
slots, apart from in archaic v1 hw.
As such, remove this function and associated code. For v1 hw, move error
handling to same scheme as other hw revisions, where we allow erroring
commands to timeout.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T5/T6 can have different pack and pad boundary value. This patch sets
packing boundary based on cache line size and PCI-E maximum payload size
and sets smallest padding boundary value.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A test program's runtime became impractically long since any non zero
ndelay (e.g. 1 nanosec) caused Start Stop Unit to delay over 8 magnitudes
greater than other commands. This patch skips long delays (on Start Stop
Unit and Synchronize Cache) if ndelay is less than or equal to 10
microsecs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't want to use 'struct timespec' because of the y2038 overflow
problem. The overflow is not actually an issue here, but it's easy to
replace with 'timespec64' for consistency. However, it's worth pointing out
that nanosecond values have nine digits, not eight or ten, so I'm fixing
the format strings accordingly as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling either fc_rport_logon() or fc_rport_logoff() during rport list
traversal we cannot use the RCU list traversal, as either of these
functions will be taking a mutex. So we need to partially revert commit
a407c59339 to take the disc mutex during traversal. We should, however,
continue to use krefs to ensure that the rport object will not be freed
from under us.
Fixes: a407c59339 ("scsi: libfc: Fixup disc_mutex handling")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The discovery rport list handling is quite odd; the list traversal is
independent from the lifetime of the rport itself. This makes auditing
quite tricky, and the chance remains that we've missed something. So this
patch adds a WARN_ON() statement when freeing an rport which is still part
of a list.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_disc_stop_rports() is calling fc_rport_logoff(), which in turn is
acquiring the rport mutex. So we cannot use RCU list traversal here, but
rather need to hold the disc mutex to avoid list corruption while
traversing.
Fixes: a407c59339 ("scsi: libfc: Fixup disc_mutex handling")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani