We have a logic in driver to delay or abort low priority scan
to serve Tx traffic effectively. With scan channel
gap support added, firmware now allows driver to send Tx data while
scan operation is in progress. Hence low priority scan handling
in driver is not required now. This patch removes related code.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With scan channel gap when any station/AP is active, FW comes back
to connected channel for any pending data transfter after scanning each
channel.
We set scan channel gap TLV to FW in scan command when any of the
interface is active. This enables scan channel gap in FW.
Also when scan channel gap is enabled, we would scan maximum channels
allowed by FW.
Scan channel gap is supported only on FW with V15 FW API.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was observed that station would sent probe request even when
scan type has been set as passive during iw scan.
This was happening because driver sets passive scan type only
when channel has IEEE80211_CHAN_NO_IR flag set.
Along with this, add condition to check if no ssids are specified in
scan request so as to mark such scan request passive.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In managed mode if the driver is getting a re-associate command
from cfg80211, driver deauthenticates with the AP internally and
sends a disconnected event to cfg80211 before completion of its
association process. The disconnected event then modifies the
SSID length as wdev->ssid_len = 0. So, upon receiving the connect
result event from driver, cfg80211 is unable to get that BSS from
the device's BSS list and generates the following WARN_ON message.
WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658
__cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Avoid re-association while the device is already associated to a
network. Also remove the internal deauthentication from the
association path.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places at the begining of Tx/Rx paths where
tx_info/rx_info is not correctly initialized. This patch
takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979.
Thomas corrected me on that I misunderstood Johannes' comment
for net_timedelta() and the ktime_get_real() usage inside
__net_timestamp().
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When magic-packet is generated as a UDP packet the offset should
be 20+8 more bytes to cover IPv4 header and UDP header. So the
total offset become 56.
Add a new MEF entry to support both magic-packet patterns
generated by different tools.
Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom regulatory domain was introduced in this commit:
cc0ba0d mwifiex: support custom world regulatory domain
The commit description says that it was introduced because the world
regulatory domain does not include channels 52-64 and 100-140. These
channels are described in the world regulatory domain now, so we can
drop this custom regulatory domain.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To set AP in 1X1 or 2X2 mode through hostapd, we need to set
RX-STBC* in hostapd.conf file. Depending upon RX-STBC bit in
ht_cap IE received from hostapd, we need to update mcs set in
bss_cfg appropriately before starting AP.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As V15 firmware supports VHT rate configuration, we can use this
information received in set bitrate mask handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if the device is changed to 1X1 mode, data is sent with
higher MCS rates after association.
This patch fixes the problem by updating MCS information field
in HT capability when antenna setting changes so that correct
information will be advertised in association and probe request.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a race condition while queuing synchronous command and
asynchronous command requested from different threads, because
the wait_q_enabled flag is set based on a global variable
cmd_wait_q_required.
The issue is fixed by removing this global variable and using a
unified function with an argument 'sync' passed into the
function.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't perform OBSS scan internally. As we intend to use
corresponding feature in application, we will enable this flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit12 in fw_cap_info is for testing only.
Remove all related code.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
8 bytes preamble
14 bytes src/dst/eth_type
6 bytes 0xff:0xff..
http://en.wikipedia.org/wiki/Wake-on-LAN#Magic_packethttp://en.wikipedia.org/wiki/EtherType
This will fail if we VLAN or the magic packet is encapsulated
as a UDP packet...
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While registering the driver with cfg80211, update the threshold
value and retry limit to cfg80211.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver gets regulatory domain change notifications or before
associates to an AP with Country IE, the txpwrlimit table stored
in device tree for that country is downloaded to firmware.
The txpwrlimit downloading will happen only at the first time
when the alpha2 country code is changed. World regulatory domain
"00" notification doesn't trigger the downloading. This behavior
is same as domain_info command.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On cfg80211 regulatory domain change, drivers gets alpha2 country
code or "00" in driver's notification handler.
In most cases, the pattern will be US, 00, US, 00, US, 00, US, ...
There is no need to send domain info to firmware in case of "00" or
with the same alpha2 country code.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skb is modified in sending the TX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Currently we freeing wdev for each interface in driver unload
path. We may leak memory if user have already deleted an interface.
mwifiex_add_virtual_intf() allocates wdev structure. So it should
be freed in mwifiex_del_virtual_intf().
This will make sure that wdev will be freed when user deletes an
interface and also in unload path.
2) "priv->netdev->ieee80211_ptr" should also be cleared in
mwifiex_del_virtual_intf.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) If register_netdevice() is failed, we are freeing netdev
pointer, but priv->netdev is not cleared. This gives kernel
paging request error when driver is unloaded or interface is
deleted. Fix the problem by clearing the pointer.
2) Fix memory leak issue by freeing 'wdev' in failure paths.
Also, clear priv->wdev pointer.
As mwifiex_add_virtual_intf() successfully handles the
failure conditions, redundant code under err_add_intf label
is removed in this patch.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.
Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
config: make ARCH=m68k allmodconfig
All error/warnings:
drivers/net/wireless/mwifiex/cfg80211.c: In function
'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
declaration of function 'mwifiex_is_pattern_supported'
[-Werror=implicit-function-declaration]
drivers/net/wireless/mwifiex/cfg80211.c: At top level:
drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
'mwifiex_cfg80211_set_coalesce' defined but not used
[-Wunused-function]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coalesce filters are configured in firmware based on settings
received from cfg80211.
Packet type which is required by firmware is determined based on
provided patterns in a rule:
Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found
Some example coalesce configuration files:
1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
32 bytes of HW 802.11 header + 8 bytes LLC +
12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.
delay=100
condition=1
patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58
2) Coalesce all broadcast and multicast packets(Multiple packet
types are not allowed in a single rule. Hence created separate
rules)
delay=400
condition=1
patterns=33:33
delay=400
condition=1
patterns=ff:ff:ff:ff
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar