Remove includes of asm/kvm_host.h from files that already include
linux/kvm_host.h to make it more obvious that there is no ordering issue
between the two headers. linux/kvm_host.h includes asm/kvm_host.h to
pick up architecture specific settings, and this will never change, i.e.
including asm/kvm_host.h after linux/kvm_host.h may seem problematic,
but in practice is simply redundant.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adapt and update current VIM2 thermal zones support so that zones are
available on all meson GXBB/GXL/GXM devices - similar to changes made
for G12A/G12B/SM1 devices.
Suggested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1584328854-28575-1-git-send-email-christianshewitt@gmail.com
The common meson-khadas-vim3.dtsi is now shared with VIM3L so move the
VIM3 model name to meson-g12b-khadas-vim3.dtsi.
meson-sm1-khadas-vim3l.dts contains the VIM3L model name.
changes in v2
- fix typo in commit message
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1583378508-14312-1-git-send-email-christianshewitt@gmail.com
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Fixes: 925c5c32f3 ("arm64: dts: uniphier: add SPI node for LD20, LD11 and PXs3")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of thermal monitor and thermal zone for UniPhier PXs3 SoC.
The thermal monitor node is included in sysctrl. This patch gives the
default value for PXs3 in the same way as LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PXs3 reference board has 2 spi connectors. This enables spi0 and spi1,
and adds aliases properties for each spi to determine device name
assignments.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the felix switch by default and enable it per board which are
actually using it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that there is support for the Felix switch this variant can also be
added. It features two external ports ethernet ports which are connected
to the internal switch core. No direct connection to any of the enetc's
is supported.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The KBox A-230-LS supports four external ports which are connected to
the internal switch of the LS1028A via QSGMII. Now that the Felix switch
is supported, add these ports in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The module itself has another EEPROM at 50h on I2C4. The EEPROM on the
carriers is located at 57h on I2C3. Fix that in the device trees.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a SPI flash on this carrier connected to the third DSPI
controller. Add it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc fsl,aips-bus.yaml, compatible and reg is
required. And for reg, the AIPS configuration space should be
used, not all the AIPS bus space.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable soundwire, slimbus frameworks, the machine driver and the codec
drivers for WCD934x and WSA881x used on varios SDM845 based designs.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200315050827.1575421-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enables e1000 Ethernet device as it is used as a low-cost failover
Ethernet port on various QorIQ reference boards. Enabled as built-in
for booting from network without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables various PHY device drivers and PHY MUX drivers used on QorIQ
reference boards supported in mainline kernel.
Enabled as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the RTC devices used on QorIQ reference boards supported in
mainline kernel.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the flash devices used on NXP/FSL QorIQ reference boards
supported in mainline kernel. Drivers are enabled as built-in for RFS
access without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the Mali display driver for the display port on NXP LS1028a SoC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables generic GPIO driver for varous QorIQ SoCs. The driver can only
be built-in right now.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables NXP/FSL QorIQ IFC flash controller driver for NAND. Enabled as
built-in to load RFS from nand flash without initramfs.
Remove CONFIG_MEMORY as it is selected by CONFIG_MTD_NAND_FSL_IFC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables ARM generic SBSA compatible watchdog driver for NXP LX2160a SoC.
Enabled as built-in for it is a core feature.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the generic QorIQ cpufreq driver to support frequency scaling
for various QorIQ SoCs. Enabled as built-in as it is a core feature.
Remove CONFIG_CLK_QORIQ as it is seleted by CONFIG_QORIQ_CPUFREQ.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables SPI controller drivers used in various NXP/FSL SoCs.
QSPI is fast enough to connect big flash for file system. It is used to
connect 512MB NAND flash and 256MB NOR flash on LS1028RDB. It is used
as bootsource for other platforms like LS2080ardb too. Enabled as
built-in to load RFS from SPI flash without requiring initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP ENETC Ethernet controller and FELIX Ethernet
switch used on QorIQ LS1028a SoC.
The ENETC ethernet drivers are enabled as built-in to boot from network
without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP DPAA2 framework, related Ethernet and crypto
device which can be found on QorIQ SoCs like LS1088a, LS2088a and
LX2160a.
The framework and ethernet drivers are enabled as built-in to boot
from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP DPAA1 framework and related Ethernet device which
can be found on QorIQ SoCs such as LS1043a and LS1046a. They are enabled
as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables driver for FLEXCAN device which is used on a wide range of NXP
SoCs. Also enabling the related CAN framework.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Used "make defconfig savedefconfig" to regenerate defconfig files in the
right order to prepare for additional defconfig changes.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
make -k ARCH=arm64 dtbs_check shows the following errors. Fix them by
removing the "arm,armv8" compatible.
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long CHECK
arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex.dt.yaml
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
armada-ap806-dual.dtsi includes armada-ap806.dtsi which describes
thermal zones for 4 cpus but only cpu0 and cpu1 only exists for dual
configuration, this makes dtb compilation fail. Fix it by removing
thermal zone nodes for non-existed cpus for dual configuration.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The commit adding ESPRESSObin variants didn't include those in Makefile to
be built.
Fixes: 447b878935 ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The commit introducing ESPRESSObin variants didn't specify dts version,
and because of that they are treated by dtc as legacy ones. Fix that by
properly specifying version in each dts.
Fixes: 447b878935 ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The maker of this board and its variants, stores MAC address in U-Boot
environment. Add alias for bootloader to recognise, to which ethernet
node inject the factory MAC address.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Allow the SFP cages to be used with 2W SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c2 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The KVM hyp code is only run after system capabilities have been
finalized, and thus all const cap checks have been patched. This is
noted in in __cpu_init_hyp_mode(), where we BUG() if called too early:
| /*
| * Call initialization code, and switch to the full blown HYP code.
| * If the cpucaps haven't been finalized yet, something has gone very
| * wrong, and hyp will crash and burn when it uses any
| * cpus_have_const_cap() wrapper.
| */
Given this, the hyp code can use cpus_have_final_cap() and avoid
generating code to check the cpu_hwcaps array, which would be unsafe to
run in hyp context.
This patch migrate the KVM hyp code to cpus_have_final_cap(), avoiding
this redundant code generation, and making it possible to detect if we
accidentally invoke this code too early. In the latter case, the BUG()
in cpus_have_final_cap() will cause a hyp panic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When cpus_have_const_cap() was originally introduced it was intended to
be safe in hyp context, where it is not safe to access the cpu_hwcaps
array as cpus_have_cap() did. For more details see commit:
a4023f6827 ("arm64: Add hypervisor safe helper for checking constant capabilities")
We then made use of cpus_have_const_cap() throughout the kernel.
Subsequently, we had to defer updating the static_key associated with
each capability in order to avoid lockdep complaints. To avoid breaking
kernel-wide usage of cpus_have_const_cap(), this was updated to fall
back to the cpu_hwcaps array if called before the static_keys were
updated. As the kvm hyp code was only called later than this, the
fallback is redundant but not functionally harmful. For more details,
see commit:
63a1e1c95e ("arm64/cpufeature: don't use mutex in bringup path")
Today we have more users of cpus_have_const_cap() which are only called
once the relevant static keys are initialized, and it would be
beneficial to avoid the redundant code.
To that end, this patch adds a new cpus_have_final_cap(), helper which
is intend to be used in code which is only run once capabilities have
been finalized, and will never check the cpus_hwcap array. This helps
the compiler to generate better code as it no longer needs to generate
code to address and test the cpus_hwcap array. To help catch misuse,
cpus_have_final_cap() will BUG() if called before capabilities are
finalized.
In hyp context, BUG() will result in a hyp panic, but the specific BUG()
instance will not be identified in the usual way.
Comments are added to the various cpus_have_*_cap() helpers to describe
the constraints on when they can be used. For clarity cpus_have_cap() is
moved above the other helpers. Similarly the helpers are updated to use
system_capabilities_finalized() consistently, and this is made
__always_inline as required by its new callers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add endpoint mode support for PCIe C5 controller in P2972-0000 platform
with information about supplies, PHY, PERST GPIO and GPIO that controls
PCIe reference clock coming from the host system.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding this alias for the Ethernet interface on Jetson TX1 allows the
bootloader to pass the MAC address to the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1 platform because the
supply regulator is not specified for the backlight.
WARNING KERN lp855x 0-002c: 0-002c supply power not found, using dummy regulator
The backlight supply is provided by the 3.3V SYS rail and so add this
as the supply for the backlight.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on the Jetson TX2 platform ...
WARNING KERN tegra-sor 15540000.sor: 15540000.sor supply \
vdd-hdmi-dp-pll not found, using dummy regulator
The problem is caused because the regulator for the SOR device is
missing the '-supply' suffix in Device-Tree. Therefore, add the
'-supply' suffix to fix this warning.
Fixes: 3fdfaf8718 ("arm64: tegra: Enable DP support on Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1, Jetson Nano and Jetson
TX2 platforms because the supply regulators are not specified for the
EEPROMs.
WARNING KERN at24 0-0050: 0-0050 supply vcc not found, using dummy regulator
WARNING KERN at24 0-0057: 0-0057 supply vcc not found, using dummy regulator
For both of these platforms the EEPROM is powered by the main 1.8V
supply rail and so populate the supply for these devices to fix these
warnings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1
module") populated the EEPROM on the Jetson TX1 module, but did not
enable the corresponding I2C controller. Enable the I2C controller so
that this EEPROM can be accessed.
Fixes: a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1 module")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
clk_out_2 is a clock provided by the PMC, rather than the clock and
reset controller, as previously erroneously defined.
This patch changes clk_out_2 provider to PMC and uses corresponding
PMC clock ID for clk_out_2.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 and Tegra210 PMC blocks have clk_out_1, clk_out_2, clk_out_3,
and a blink clock as a part of the PMC.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
Clock IDs for these clocks are defined in the PMC dt-bindings.
This patch updates the device tree to include the PMC dt-bindings header
and adds the #clock-cells property with one clock specifier to the PMC
node.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to peripheral USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to OTG USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate OTG vbus regulator and add usb-role-switch entry to USB 2-0
port and corresponding connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables XUSB host and pad controller in Tegra194
P2972-0000 board.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
from Advantech, however the panel isn't sold alongside the board.
A new dts, adding everything that's required to get the panel to
work with HiHope RZ/G2M, is the most convenient way to support the
HiHope RZ/G2M when it's connected to the idk-1110wr.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/1583957020-16359-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas M3ULCB board equipped with an R-Car
M3-W+ SiP with 8 (2 x 4) GiB of RAM.
To avoid build error on 'ulcb.dtsi', ssi2 is added into 'r8a77961.dtsi'.
Based on commit 92980759c1 ("arm64: dts: renesas: Add support for
Salvator-XS with R-Car M3-W+").
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Link: https://lore.kernel.org/r/20200309064425.25437-3-yuya.hamamachi.sx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200306110025.24747-1-geert+renesas@glider.be
The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200307091302.14881-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the redundant _mem suffix for SDHC reg names.
For SDcard instance, no need supply reg names since hc reg map
is accessed with index. So remove reg names for SDcard.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enabling CQE support for eMMC by supplying the correct reg name
and flag which indicates CQE support.
Also remove the redundant _mem suffix for reg names.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5 ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently, the EL0 SP alignment handler masks IRQs unnecessarily. It
does so due to historic code sharing of the EL0 SP and PC alignment
handlers, and branch predictor hardening applicable to the EL0 SP
handler.
We began masking IRQs in the EL0 SP alignment handler in commit:
5dfc6ed277 ("arm64: entry: Apply BP hardening for high-priority synchronous exception")
... as this shared code with the EL0 PC alignment handler, and branch
predictor hardening made it necessary to disable IRQs for early parts of
the EL0 PC alignment handler. It was not necessary to mask IRQs during
EL0 SP alignment exceptions, but it was not considered harmful to do so.
This masking was carried forward into C code in commit:
582f95835a ("arm64: entry: convert el0_sync to C")
... where the SP/PC cases were split into separate handlers, and the
masking duplicated.
Subsequently the EL0 PC alignment handler was refactored to perform
branch predictor hardening before unmasking IRQs, in commit:
bfe298745a ("arm64: entry-common: don't touch daif before bp-hardening")
... but the redundant masking of IRQs was not removed from the EL0 SP
alignment handler.
Let's do so now, and make it interruptible as with most other
synchronous exception handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
When building allnoconfig:
arch/arm64/kernel/cpu_errata.c:174:13: warning: unused function
'call_smc_arch_workaround_1' [-Wunused-function]
static void call_smc_arch_workaround_1(void)
^
1 warning generated.
Follow arch/arm and mark this function as __maybe_unused.
Fixes: 4db61fef16 ("arm64: kvm: Modernize __smccc_workaround_1_smc_start annotations")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Missing argument of another SYM_INNER_LABEL() breaks build for
CONFIG_FUNCTION_GRAPH_TRACER=y.
Fixes: e2d591d29d ("arm64: entry-ftrace.S: Convert to modern annotations for assembly functions")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: amba: $nodename:0:
'amba' does not match
'^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i.MX8MQ Phanbell board uses Realtek RTL8211FD as Ethernet PHY.
Its datasheet states that the proper post reset duration should be at least 50 ms.
Fixes: f34d4bfab3 ("arm64: dts: imx8mq-phanbell: Add support for ethernet")
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull in downstream patch from NXP repository to enable fspi device.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto child nodes should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
for example this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: mmc@fe320000:
'clock-freq-min-max' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'clock-freq-min-max' is deprecated, so replace it by 'max-frequency'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dt.yaml: mmc@fe320000:
'vqmmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'vqmmc' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dt.yaml: mmc@ff0c0000:
'no-emmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'no-emmc' is not a valid property name for mmc nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below without
additional properties in 'rockchip-vop.yaml' gives this error:
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff470000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff460000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
'rockchip,grf' is not used by the Rockchip VOP driver,
so remove it from 'vop' nodes in 'px30.dtsi'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
rockchip/rockchip-vop.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309081600.3887-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "spi-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine spi-rockchip.yaml and
spi-controller.yaml it gives this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: spi@ff1d0000:
'max-freq' does not match any of the regexes:
'^.*@[0-9a-f]+$', '^slave$'
'max-freq' is not a valid property name for spi nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309125145.14455-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update fspi node compatibles of LX2160A-RDB to "jedec,spi-nor" for
automatic detection of flash.
This also helps in fixing below warning:
spi-nor spi0.0: found mt35xu512aba, expected m25p80
spi-nor spi0.1: found mt35xu512aba, expected m25p80
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the iommu-map property to the pci nodes so that the firmware
fixes it up with the required values thus enabling iommu for
devices connected over pci.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: /: compatible:
['rockchip,rk3399-evb', 'rockchip,rk3399', 'google,rk3399evb-rev2']
is not valid under any of the given schemas
'google,rk3399evb-rev2' was a no longer used variant for Google.
The binding only mentions 'rockchip,rk3399-evb', 'rockchip,rk3399',
so fix this error by removing 'google,rk3399evb-rev2' from
the compatible property in rk3399-evb.dts and change it into
generic rk3399-evb support only.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302092759.3291-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The IMU chip on the librem5-devkit is not mounted at the "natural" place
that would match normal phone orientation (see the documentation for the
details about what that is).
Since the lsm9ds1 driver supports providing a mount matrix, we can describe
the orientation on the board in the dts:
Create a right-handed coordinate system (x * -1; see the datasheet for the
axis) and rotate 180 degrees around the y axis because the device sits on
the back side from the display.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The poly fuses can handle 6V 4Amps so incease the kernel limts to 5V
3.5Amps.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By adding broken-cd to the usdhc2 stanza the Redpine card can be
detected when the HKS is turned off and on.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify which regulator is used for cpufreq DVFS.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the WoWWAN signal to a gpio key to wake up the system from suspend.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the simcom SIM7100 modem and the sai6 interface that connects it.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the sgtl5000 of the librem 5 devkit in devicetree.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds 4 eeprom support on i2c mux channel #0 -
1. Bootable 512Kbit eeprom at address 0x50.
2. Memory SO-DIMMs SPD channels at 0x51 (upper SO-DIMM) and 0x53.
3. 2Kb eeprom at 0x57 will be used by SolidRun to hold manufacturing
data.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LTC3882 regulator so that the hardware monitoring
can be used with this device. This regulator provides the 0.78V
supply for the LX2160A.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX8M SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b9213899d2b0 ("arm64: dts: ls1028a: disable all enetc ports
by default") all the network ports are disabled by default. This makes
sense, but now we have to enable them explicitly in the boards. Do so
for the sl28 module.
Since we are at it. Make sure the second port is only enabled for the
variant 4 of the module. Variant 3 has only one network port.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the switch PHY nodes to the central MDIO controller PCIe endpoint
node on LS1028A (implemented as PF3) so that PHYs are accessible via
MDIO.
Enable SGMII AN on the Felix PCS by telling PHYLINK that the VSC8514
quad PHY is capable of in-band-status.
The PHYs are used in poll mode due to an issue with the interrupt line
on current revisions of the LS1028A-RDB board.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the switch device node, available on PF5, so that the switch port
sub-nodes (net devices) can be linked to corresponding board specific
phy nodes (external ports) or have their link mode defined (internal
ports).
The switch device features 6 ports, 4 with external links and 2
internally facing to the LS1028A SoC and connected via fixed links to 2
internal ENETC Ethernet controller ports.
Add the corresponding ENETC host port device nodes, mapped to PF2 and
PF6 PCIe functions. Since the switch only supports tagging on one CPU
port, only one port pair (swp4, eno2) is enabled by default and the
other, lower speed, port pair is disabled to prevent the PCI core from
probing them. If enabled, swp5 will be a fixed-link slave port.
DSA tagging can also be moved from the swp4-eno2 2.5G port pair to the
1G swp5-eno3 pair by changing the ethernet = <&enetc_port2> phandle to
<&enetc_port3> and moving it under port5, but in that case enetc_port2
should not be disabled, because it is the hardware owner of the Felix
PCS and disabling its memory would result in access faults in the Felix
DSA driver.
All ports are disabled by default, including the CPU port, and need to
be enabled on a per-board basis.
The phy-mode binding of the internal ENETC ports was modified from
"gmii" to "internal" to match the phy-mode of the internal-facing switch
ports connected to them. The ENETC driver does not perform any phy_mode
validation anyway, so the change is only cosmetic. Also, enetc_port2 is
defined as a fixed-link 1000 Mbps port even though it is 2500 Mbps (as
can be seen by the fact that it is connected to mscc_felix_port4). The
fact that it is currently defined as 1000 Mbps is an artifact of its
PHYLIB implementation instead of PHYLINK (the former can't describe a
fixed-link speed higher than what swphy can emulate from the Clause 22
MDIO spec).
The switch's INTB interrupt line signals:
- PTP TX timestamp availability
- TSN Frame Preemption
And don't forget to enable the 4MB BAR4 in the root complex ECAM space,
where the switch registers are mapped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are few boards that enable all ENETC ports, so instead of having
board DTs disable them, do so in the DTSI and have the boards enable the
ports they use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This specifier overrides the interrupt specifier with 3 cells from gic
(/interrupt-controller@6000000), but in fact ENETC is not an interrupt
controller, so the property is bogus.
Interrupts used by the children of the ENETC RCIE must use the full
3-cell specifier required by the GIC.
The issue has no functional consequence so there is no real reason to
port the patch to stable trees.
Fixes: 927d7f8575 ("arm64: dts: fsl: ls1028a: Add PCI IERC node and ENETC endpoints")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unlike on arm32, the HAVE_ARM_ARCH_TIMER config symbol does not exist on
arm64.
Note that the toplevel ARM64 symbol always selects ARM_ARCH_TIMER, so
support for it is always included.
Fixes: 628d30d1cc ("arm64: Add platform selection for BCM2835.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We need the vt fixes in here and it resolves a merge issue with
drivers/tty/vt/selection.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sm8250 devicetree file for SM8250 SoC and SM8250 MTP platform.
This file adds the basic nodes like cpu, psci and other required
configuration for booting up to the serial console.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200310050910.506854-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable Coresight funnel 4 and 5, for now, as these causes the MTP to
crash when clock late_initcall disables unused clocks.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200308055445.1992189-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
efi-entry.o is built on demand for efi-entry.stub.o, so you do not have
to repeat $(CONFIG_EFI) here. Adding it to 'targets' is enough.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Throwing our __uint128_t idioms at csum_ipv6_magic() makes it
about 1.3x-2x faster across a range of microarchitecture/compiler
combinations. Not much in absolute terms, but every little helps.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Use these for the compat VDSO,
allowing us to drop the custom ARM_ENTRY() and ARM_ENDPROC() macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Convert the assembly function in the
arm64 VDSO to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
The SDEI entry points are currently annotated as normal functions but
are called from non-kernel contexts with non-standard calling convention
and should therefore be annotated as such so do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: James Morse <james.Morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions.
Using these for __smccc_workaround_1_smc is more involved than for most
symbols as this symbol is annotated quite unusually, rather than just have
the explicit symbol we define _start and _end symbols which we then use to
compute the length. This does not play at all nicely with the new style
macros. Instead define a constant for the size of the function and use that
in both the C code and for .org based size checks in the assembly code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
We have recently introduced new macros for annotating assembly symbols
for things that aren't C functions, SYM_CODE_START() and SYM_CODE_END(),
in an effort to clarify and simplify our annotations of assembly files.
Using these for __bp_harden_hyp_vecs is more involved than for most symbols
as this symbol is annotated quite unusually as rather than just have the
explicit symbol we define _start and _end symbols which we then use to
compute the length. This does not play at all nicely with the new style
macros. Since the size of the vectors is a known constant which won't vary
the simplest thing to do is simply to drop the separate _start and _end
symbols and just use a #define for the size.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions. Update the more
straightforward annotations in the kvm code to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These include specific
annotations for the start and end of data, update symbols for data to use
these.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Neither stext nor preserve_boot_args
is called with the usual AAPCS calling conventions and they should
therefore be annotated as code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the core kernel code to
the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
return_to_handler does entertaining things with LR so doesn't follow the
usual C conventions and should therefore be annotated as code rather than
a function.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
The patchable function entry versions of ftrace_*_caller don't follow the
usual AAPCS rules, pushing things onto the stack which they don't clean up,
and therefore should be annotated as code rather than functions.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the core kernel code to
the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions. Update the
remaining annotations in the entry.S code to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
ret_from_fork is not a normal C function and should therefore be
annotated as code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. The vector table and handlers aren't
normal C style code so should be annotated as CODE.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the rest of the code has been converted to the modern START/END
macros the AES_ENTRY() and AES_ENDPROC() macros look out of place and
like they need updating. Rename them to AES_FUNC_START() and AES_FUNC_END()
to line up with the modern style assembly macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
A couple of functions were missed in the modernisation of assembly macros,
update them too.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix typo in a comment in arch/arm64/include/asm/esr.h
"Unallocted" -> "Unallocated"
Signed-off-by: Chenggang Wang <wangchenggang@vivo.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch increases the reg addresses for QSPI boot and QSPI rootfs for
Stratix10 and Agilex to cater for the increased size of kernel Image.
Signed-off-by: Joyce Ooi <joyce.ooi@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Both, OrangePi One Plus and OrangePi Lite 2 have HDMI output. Enable it
in common DTSI.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
OrangePi One Plus has gigabit ethernet. Add nodes for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.
Move external oscillator node from common H6 dtsi to board specific dts
files where present.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Make zynqmp_firmware driver as optional to disable it, if user don't
want to use default zynqmp firmware interface.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was
a miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing for
a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms.
-----BEGIN PGP SIGNATURE-----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=gCNz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was a
miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing
for a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (37 commits)
ARM: socfpga_defconfig: Add back DEBUG_FS
arm64: dts: socfpga: agilex: Fix gmac compatible
ARM: bcm2835_defconfig: Explicitly restore CONFIG_DEBUG_FS
arm64: dts: meson: fix gxm-khadas-vim2 wifi
arm64: dts: meson-sm1-sei610: add missing interrupt-names
ARM: meson: Drop unneeded select of COMMON_CLK
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
tee: amdtee: fix memory leak in amdtee_open_session()
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
...
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in the smd-rpm-regulator binding and confirmed by the
pm8616 device specification, there is no vdd_l5. l5 vdd comes from
vdd_l4_l5_l6. Fix that (though it does not cause any issue since
the supply is not requested).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1583516368-29593-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl5iMUgQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNMpPB/9OH2pp6QaosJKz6zHawyvG6K1RxCQC7TZw
PCXKWF1N9b1z/ZBq47goDC0rRxVzx+OAO9MY4DMLojWvv51GT/Z/LhrYkpXek48I
Dkfz8ZmhSyO54M8LDQQ79zKG4FzpLVsvVP2z9bMaq9Ut5BSNcKmjvY7h27/znk7N
fW0lRVBt3C7Cu5DTBqq3BN3AXEwoANb4QvqmmA6D/pZvl5MUXolulww6czknYyIE
VD7m7s6A3bPUWWVSWHuYxL9/N8fP7HbcBL09dEtIKI4n1O+mvvCx9uHxxokBGuSV
ENu7BWfm0LJ5JibbW/rSOT8u2tw4xY4njhXu06PnxWXQSF8RcaOV
=7zhy
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are another three arm64 fixes for 5.6, all pretty minor. Main
thing is fixing a silly bug in the fsl_imx8_ddr PMU driver where we
would zero the counters when disabling them.
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix ASID limit in boot messages
drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer
drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition
The Frequency Invariance Engine (FIE) is providing a frequency
scaling correction factor that helps achieve more accurate
load-tracking.
So far, for arm and arm64 platforms, this scale factor has been
obtained based on the ratio between the current frequency and the
maximum supported frequency recorded by the cpufreq policy. The
setting of this scale factor is triggered from cpufreq drivers by
calling arch_set_freq_scale. The current frequency used in computation
is the frequency requested by a governor, but it may not be the
frequency that was implemented by the platform.
This correction factor can also be obtained using a core counter and a
constant counter to get information on the performance (frequency based
only) obtained in a period of time. This will more accurately reflect
the actual current frequency of the CPU, compared with the alternative
implementation that reflects the request of a performance level from
the OS.
Therefore, implement arch_scale_freq_tick to use activity monitors, if
present, for the computation of the frequency scale factor.
The use of AMU counters depends on:
- CONFIG_ARM64_AMU_EXTN - depents on the AMU extension being present
- CONFIG_CPU_FREQ - the current frequency obtained using counter
information is divided by the maximum frequency obtained from the
cpufreq policy.
While it is possible to have a combination of CPUs in the system with
and without support for activity monitors, the use of counters for
frequency invariance is only enabled for a CPU if all related CPUs
(CPUs in the same frequency domain) support and have enabled the core
and constant activity monitor counters. In this way, there is a clear
separation between the policies for which arch_set_freq_scale (cpufreq
based FIE) is used, and the policies for which arch_scale_freq_tick
(counter based FIE) is used to set the frequency scale factor. For
this purpose, a late_initcall_sync is registered to trigger validation
work for policies that will enable or disable the use of AMU counters
for frequency invariance. If CONFIG_CPU_FREQ is not defined, the use
of counters is enabled on all CPUs only if all possible CPUs correctly
support the necessary counters.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Access to the AMU counters should be disabled by default in kvm guests,
as information from the counters might reveal activity in other guests
or activity on the host.
Therefore, disable access to AMU registers from EL0 and EL1 in kvm
guests by:
- Hiding the presence of the extension in the feature register
(SYS_ID_AA64PFR0_EL1) on the VCPU.
- Disabling access to the AMU registers before switching to the guest.
- Trapping accesses and injecting an undefined instruction into the
guest.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The activity monitors extension is an optional extension introduced
by the ARMv8.4 CPU architecture. In order to access the activity
monitors counters safely, if desired, the kernel should detect the
presence of the extension through the feature register, and mediate
the access.
Therefore, disable direct accesses to activity monitors counters
from EL0 (userspace) and trap them to EL1 (kernel).
To be noted that the ARM64_AMU_EXTN kernel config does not have an
effect on this code. Given that the amuserenr_el0 resets to an
UNKNOWN value, setting the trap of EL0 accesses to EL1 is always
attempted for safety and security considerations. Therefore firmware
should still ensure accesses to AMU registers are not trapped in
EL2/EL3 as this code cannot be bypassed if the CPU implements the
Activity Monitors Unit.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The activity monitors extension is an optional extension introduced
by the ARMv8.4 CPU architecture. This implements basic support for
version 1 of the activity monitors architecture, AMUv1.
This support includes:
- Extension detection on each CPU (boot, secondary, hotplugged)
- Register interface for AMU aarch64 registers
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The default value of Kconfig for almost all sprd drivers are the same with
ARCH_SPRD, making these drivers built as modules as default would be easier
if we can set ARCH_SPRD as 'm', so this patch change ARCH_SPRD to tristate.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200305103228.9686-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The (CFS) scheduler has some extra logic catering to systems with SMT, but
that logic won't be compiled in unless the above config is set.
Note that the SMT-centric codepaths are gated by the sched_smt_present
static key, and the SMT sched_domains will only survive if the platform has
SMT. As such, the only impact on !SMT platforms should be a slightly
bigger kernel - no behavioural change.
Distro kernels already enable it, which makes sense since there already are
things like ThunderX2 out in the wild. Enable it for the defconfig.
Some deltas
===========
FWIW my ELF symbol table diff looks something like this:
NAME BEFORE AFTER DELTA
update_sd_lb_stats.constprop.135 0 1864 +1864
find_idlest_group.isra.115 0 1808 +1808
update_numa_stats.isra.121 0 628 +628
select_task_rq_fair 3236 3732 +496
compute_energy.isra.112 0 420 +420
score_nearby_nodes.part.120 0 380 +380
__update_idle_core 0 232 +232
nohz_balance_exit_idle.part.127 0 216 +216
sched_slice.isra.99 0 172 +172
update_load_avg.part.107 0 116 +116
wakeup_preempt_entity.isra.101 0 92 +92
sched_cpu_activate 340 396 +56
pick_next_task_idle 8 56 +48
sched_cpu_deactivate 252 292 +40
show_smt_active 44 80 +36
cpu_smt_mask 0 28 +28
set_next_task_idle 4 32 +28
task_numa_work 680 692 +12
cpu_smt_flags 0 8 +8
enqueue_task_fair 2608 2612 +4
wakeup_preempt_entity.isra.104 92 0 -92
update_load_avg 1028 932 -96
task_numa_migrate 1824 1728 -96
sched_slice.isra.102 172 0 -172
nohz_balance_exit_idle.part.130 216 0 -216
task_numa_find_cpu 2116 1868 -248
score_nearby_nodes.part.123 380 0 -380
compute_energy.isra.115 420 0 -420
update_numa_stats.isra.124 472 0 -472
find_idlest_group.isra.118 1808 0 -1808
update_sd_lb_stats.constprop.138 1864 0 -1864
------------------------------------------------------------------
DELTA SUM +820
As for the sched_domains, this is on a hikey960:
before:
$ cat /proc/sys/kernel/sched_domain/cpu*/domain*/name | sort | uniq
DIE
MC
after:
$ cat /proc/sys/kernel/sched_domain/cpu*/domain*/name | sort | uniq
DIE
MC
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200227191433.31994-3-valentin.schneider@arm.com
To enable kernel critical shutdown feature added critical trip point to
all non CPU sensors to perform shutdown in orderly manner.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Link: https://lore.kernel.org/r/1583394547-12779-2-git-send-email-rkambl@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The CLKREF clocks in GCC are parented by RPM_SMD_LN_BB_CLK, through the
CXO2 pad. Wire this up so that this is properly enabled when need by the
various PHYs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200106080546.3192125-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When an ahash algorithm fallback to another ahash and that fallback is
shaXXX-CE, doing export/import lead to error like this:
alg: ahash: sha1-sun8i-ce export() overran state buffer on test vector 0, cfg=\"import/export\"
This is due to the descsize of shaxxx-ce being larger than struct shaxxx_state
off by an u32.
For fixing this, let's implement export/import which rip the finalize
variant instead of using generic export/import.
Fixes: 6ba6c74dfc ("arm64/crypto: SHA-224/SHA-256 using ARMv8 Crypto Extensions")
Fixes: 2c98833a42 ("arm64/crypto: SHA-1 using ARMv8 Crypto Extensions")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no enable-gpio for backlight control on rk3399 evb,
actually GPIO1_B5 is for LCD panle enable. So remove it from backlight
dt node.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20200305113912.32226-4-andy.yan@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the DT nodes for each of the Network-On-Chip interconnect
buses found on SDM845 based platform and redefine the rsc_hlos
child node as a bcm-voter device to better represent the hardware.
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200209183411.17195-7-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is just like commit a1875bf982 ("arm64: dts: qcom: sdm845: Add
unit name to soc node") but for sc7180.
For reference, the warning being fixed was:
Warning (unit_address_vs_reg): /soc:
node has a reg or ranges property, but no unit name
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 90db71e480 ("arm64: dts: sc7180: Add minimal dts/dtsi files for SC7180 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200304105638.1.I9ea0d337fcb927f52a28b20613b2377b6249c222@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are no applicable literals above them.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Remi Denis-Courmont <remi.denis.courmont@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arch code for hot-remove must tear down portions of the linear map and
vmemmap corresponding to memory being removed. In both cases the page
tables mapping these regions must be freed, and when sparse vmemmap is in
use the memory backing the vmemmap must also be freed.
This patch adds unmap_hotplug_range() and free_empty_tables() helpers which
can be used to tear down either region and calls it from vmemmap_free() and
___remove_pgd_mapping(). The free_mapped argument determines whether the
backing memory will be freed.
It makes two distinct passes over the kernel page table. In the first pass
with unmap_hotplug_range() it unmaps, invalidates applicable TLB cache and
frees backing memory if required (vmemmap) for each mapped leaf entry. In
the second pass with free_empty_tables() it looks for empty page table
sections whose page table page can be unmapped, TLB invalidated and freed.
While freeing intermediate level page table pages bail out if any of its
entries are still valid. This can happen for partially filled kernel page
table either from a previously attempted failed memory hot add or while
removing an address range which does not span the entire page table page
range.
The vmemmap region may share levels of table with the vmalloc region.
There can be conflicts between hot remove freeing page table pages with
a concurrent vmalloc() walking the kernel page table. This conflict can
not just be solved by taking the init_mm ptl because of existing locking
scheme in vmalloc(). So free_empty_tables() implements a floor and ceiling
method which is borrowed from user page table tear with free_pgd_range()
which skips freeing page table pages if intermediate address range is not
aligned or maximum floor-ceiling might not own the entire page table page.
Boot memory on arm64 cannot be removed. Hence this registers a new memory
hotplug notifier which prevents boot memory offlining and it's removal.
While here update arch_add_memory() to handle __add_pages() failures by
just unmapping recently added kernel linear mapping. Now enable memory hot
remove on arm64 platforms by default with ARCH_ENABLE_MEMORY_HOTREMOVE.
This implementation is overall inspired from kernel page table tear down
procedure on X86 architecture and user page table tear down method.
[Mike and Catalin added P4D page table level support]
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arm64 page table dump code can race with concurrent modification of the
kernel page tables. When a leaf entries are modified concurrently, the dump
code may log stale or inconsistent information for a VA range, but this is
otherwise not harmful.
When intermediate levels of table are freed, the dump code will continue to
use memory which has been freed and potentially reallocated for another
purpose. In such cases, the dump code may dereference bogus addresses,
leading to a number of potential problems.
Intermediate levels of table may by freed during memory hot-remove,
which will be enabled by a subsequent patch. To avoid racing with
this, take the memory hotplug lock when walking the kernel page table.
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEoHhMeiyk5VmwVMwNGZQEC4GjKPQFAl5ed6QUHGRpbmd1eWVu
QGtlcm5lbC5vcmcACgkQGZQEC4GjKPS0dA//Vctu2B9YYK+X8KtO3AFVCc2HA69A
JIMnsYReTn1HBHsoZQCXVJajsWI+J4h+z2hxQpGQHXcVzfpg6gFb5HLGqvAG+fZO
MORVlN4ne96cYcOjA/8eTQOIkFigPrQIK3lZGR6nEJ6PzCz3bOfKdbtOChvuH4ev
g/2I8O9FIL2u+Xa1BdxHXvOU24FZttH2OrIVHgdsnbdV1mtY3yDTTlyiOVDvgTRu
kkv9PM3GnnSfQyNQOLRkSwfF+fvWrEV1+XFRsbotliuVGPOgHQ0WbsqAW+6fhh9W
r/JIDxlgy6ddG9MQGZdtZC48Lem9ITk1g710uiVDQx710amzJfY1an6vB8xqtqab
6xNuxS6AqaEmzwQbzdT9AmFKa6EAKicOrYfN0XNBKvlqoF/IxR3EJYYJ0shxHgK/
ACn1e53nNnPzi9dg4y0IezmxUNf4jl6T+Su/791ofc8Edx+iNRLOyshex4tFD4zf
8mVgoBNp5yzkdAAyNjd1x9c7YPKxWUVLZkD4vNp5QObjdutjOsA1j6w9YTKZooBA
BZZ5974rYZWvL7lHWoA0vaZDMF6cJ1osIP1d4cA49jXLHl33o5X22Lgy0lhBoL9F
fTeWnmVgEdhlHXDWwjKh0vfDJ9EZnMlfTlWzTwnmRJEAswQBgk+wleDarSs0o8Ac
pn6wton5J8JL/eQ=
=VAHM
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: agilex: fix gmac compatible
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
* tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: (578 commits)
arm64: dts: socfpga: agilex: Fix gmac compatible
Linux 5.6-rc4
KVM: VMX: check descriptor table exits on instruction emulation
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
macintosh: therm_windtunnel: fix regression when instantiating devices
jbd2: fix data races at struct journal_head
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
MAINTAINERS: Correct Cadence PCI driver path
io_uring: fix 32-bit compatability with sendmsg/recvmsg
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
...
Link: https://lore.kernel.org/r/20200303153509.28248-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix gmac compatible string to "altr,socfpga-stmmac-a10-s10". Gmac for
Agilex should use same compatible as Stratix 10.
Fixes: 4b36daf9ad ("arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA")
Cc: stable@vger.kernel.org
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This is largely cosmetic, but Odroid N2 and Khadas VIM3 are G12B devices so
correct the card model names to reflect this.
Fixes: aa7d5873bf ("arm64: dts: meson-g12b-odroid-n2: add sound card")
Fixes: c6d29c66e5 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[khilman: fix whitespace in commit log trailers]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1583135051-95529-1-git-send-email-christianshewitt@gmail.com
Since commit f88f42f853 ("arm64: context: Free up kernel ASIDs if KPTI
is not in use"), the NUM_USER_ASIDS macro doesn't correspond to the
effective number of ASIDs when KPTI is enabled. Get an accurate number
of available ASIDs in an arch_initcall, once we've discovered all CPUs'
capabilities and know if we still need to halve the ASID space for KPTI.
Fixes: f88f42f853 ("arm64: context: Free up kernel ASIDs if KPTI is not in use")
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Add support for matching the new PMUs. For now, this just wires them up
as generic PMUv3 such that people writing DTs for new SoCs can do the
right thing, and at least have architectural and raw events be usable.
We can come back and fill in event maps for sysfs and/or perf tools at
a later date.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The PMU init callbacks are already drowning in boilerplate, so before
doubling the number of supported PMU models, give it a sensible refactor
to significantly reduce the bloat, both in source and object code.
Although nobody uses non-default sysfs attributes today, there's minimal
impact to preserving the notion that maybe, some day, somebody might, so
we may as well keep up appearances.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
videostrong kii pro comes with a nec rc, add the keymap to the dts
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
as too large frame sizes on some configurations. On the
ARM side, the compiler was messing up shadow stacks between
EL1 and EL2 code, which is easily fixed with __always_inline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeXAT4AAoJEL/70l94x66DWywH/1kv4MmeGo6PI0Nxk/yvA7X8
78iqIBchtxZX0v/9kqpTB7bYmHyTgmZHM+IkwtIUANDSaOvWqJwU+TLUfduOiuXF
NxBHcZDyuMoftX5CSQ+bJ5PwxKijAdJsIkCZ13CnsTCkwcfamSGypFUCK8LacPeq
WHvV5Ws5pFc51xrP3CH1DrRhLoulaBmt5xxqK9fxWtslrlsnm1uNza5vs8As8CzM
apnmdRIf5p4v91Zic3PFH7/GXES0m1tjIBKdtZ4YHb8yrXV/kBsEVhhTjqE9mrUq
qtRRl5waOFoP4yc9ey52PAbMm1x1Ho/pyunpM0xh40Yq8OPFwqXBPTnWfobSoiM=
=LNQc
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"More bugfixes, including a few remaining "make W=1" issues such as too
large frame sizes on some configurations.
On the ARM side, the compiler was messing up shadow stacks between EL1
and EL2 code, which is easily fixed with __always_inline"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: check descriptor table exits on instruction emulation
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
arm64: Ask the compiler to __always_inline functions used by KVM at HYP
KVM: arm64: Define our own swab32() to avoid a uapi static inline
KVM: arm64: Ask the compiler to __always_inline functions used at HYP
kvm: arm/arm64: Fold VHE entry/exit work into kvm_vcpu_run_vhe()
KVM: arm/arm64: Fix up includes for trace.h
before
[6.418252] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.435663] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.551259] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[6.551275] brcmfmac: brcmf_sdio_verifymemory: error -84 on reading 2048 membytes at 0x00184000
[6.551352] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
after
[6.657165] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.660807] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918643] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918734] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[6.922724] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4356/2 wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
Fixes: adc52bf7ef ("arm64: dts: meson: fix mmc v2 chips max frequencies")
Suggested-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1582212790-11402-1-git-send-email-christianshewitt@gmail.com
The lvds controller has two ports. port@0 for the connection
to the display controller(s) and port@1 for the connection to
the panel, so should have a ports node covering the port@x nodes.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200121222055.4068166-1-heiko@sntech.de
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.
The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.
This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.
For reference, see https://lkml.org/lkml/2019/4/1/1382.
Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399pro-rock-pi-n10.dt.yaml: /: compatible:
['radxa,rockpi-n10', 'rockchip,rk3399pro']
is not valid under any of the given schemas
During the review process the binding was changed,
but the dts file was somehow not updated.
Fix this error by adding 'vamrs,rk3399pro-vmarc-som' to
the compatible property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228061436.13506-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter Xu