Commit Graph

34 Commits

Author SHA1 Message Date
Eliad Peller 4b29886feb wl12xx: configure rate policy for p2p operations
p2p packets should go out only with OFDM rates.

Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).

Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-07 08:31:43 +03:00
Shahar Levi 06b660e1a3 wl12xx: Include OFDM rates in IBSS mode
We were including only 11b rates in IBSS mode.  This patch adds OFDM
rates.

[Rephrased commit log and removed one unnecessary comment. -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23 14:21:36 +03:00
Eliad Peller 9487775c5b wl12xx: add config_hangover command
Add wl12xx_acx_config_hangover() and respective conf values.
This command configures how long the chip will stay awake
after it was configured to enter psm.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14 11:47:26 +03:00
Arik Nemtsov 1a8adb67f9 wl12xx: AP-mode - configure HT rate support to the FW
Unconditionally configure HT rate support to the FW on all ACs
when starting the AP.

When 11n support is disabled by usermode (hostapd), each STA joining
the AP will appear as a non-HT STA. This will stop us from accidentally
transmitting using MCS rates.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-22 12:35:29 +03:00
Arik Nemtsov 0f9c8250e1 wl12xx: re-enable block ack session support
Incorporate interface changes for HT support.

Add ba_bitmap field to the wl1271_link struct, to indicate
activate RX BA sessions (for AP mode).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-22 12:35:27 +03:00
Eliad Peller 3be4112cb2 wl12xx: update BT coex configuration params
The BT coex params api have been changed.
Update it, and init coex for both sta and ap.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-22 12:35:27 +03:00
Eliad Peller fa6ad9f0f3 wl12xx: add set_rate_mgmt_params acx
Configure rate management parameters on hw init

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-22 12:35:25 +03:00
Arik Nemtsov 3618f30f30 wl12xx: AP mode - support FW TX inactivity triggers
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-07-05 21:33:20 +03:00
Ido Yariv 95dac04f88 wl12xx: Support routing FW logs to the host
A recently added feature to the firmware enables the driver to retrieve
firmware logs via the host bus (SDIO or SPI).

There are two modes of operation:
1. On-demand: The FW collects its log in an internal ring buffer. This
   buffer can later be read, for example, upon recovery.
2. Continuous: The FW pushes the FW logs as special packets in the RX
   path.

Reading the internal ring buffer does not involve the FW. Thus, as long
as the HW is not in ELP, it should be possible to read the logs, even if
the FW crashes.

A sysfs binary file named "fwlog" was added to support this feature,
letting a monitor process read the FW messages. The log is transferred
from the FW only when available, so the reading process might block.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-06-27 15:10:56 +03:00
Eliad Peller 77ddaa108f wl12xx: add automatic rx streaming triggers
When rx_streaming.interval is non-zero, use automatic rx streaming.
Enable rx streaming on the each rx/tx packet, and disable it
rx_streaming.duration msecs later.

When rx_streaming.always=0 (default), rx streaming is enabled only
when there is a coex operation.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-06-27 10:15:49 +03:00
Eliad Peller f84673d597 wl12xx: add support for rx streaming
wl12xx supports the "rx streaming" feature:

When in ps mode, and @timeout msecs have been passed since
the last rx/tx, it issues trigger packets (QoS-null/PS-Poll packets,
according to the ac type) in const intervals (in order to reduce
the rx time).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-06-27 10:15:48 +03:00
Luciano Coelho 50a66d7f04 wl12xx: add separate config value for DFS dwell time on sched scan
Use a different value for DFS dwell time when performing a scheduled
scan.  Previously we were using the same value as for normal passive
scans.  This adds some flexibility between these two different types
of passive scan.

For now we use 150 TUs for DFS channel dwell time.  This may need to
be fine-tuned in the future.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-31 14:47:25 -04:00
John W. Linville e00cf3b9eb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn-tx.c
	net/mac80211/sta_info.h
2011-05-16 19:32:19 -04:00
Luciano Coelho 3a9d60e5bd wl12xx: add configuration values for scheduled scan
Add the structures and values for driver-configured scheduled scan
parameters.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-05-13 00:06:32 +03:00
John W. Linville a70171dce9 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/libertas/if_cs.c
	drivers/net/wireless/rtlwifi/pci.c
	net/bluetooth/l2cap_sock.c
2011-05-05 13:32:35 -04:00
Luciano Coelho 25eaea30cd Revert "wl12xx: support FW TX inactivity triggers"
This reverts commit 47684808fd.

Conflicts:

	drivers/net/wireless/wl12xx/conf.h
	drivers/net/wireless/wl12xx/main.c
2011-05-02 12:46:40 +03:00
Arik Nemtsov 70f474241b wl12xx: AP-mode - overhaul rate policy configuration
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.

When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.

Unify rate configuration on initialization and on change notification
into a single function.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-05-02 10:31:13 +03:00
Arik Nemtsov 801f870bc0 wl12xx: add BT-coexistance for AP
Initialize AP specific BT coexitance parameters to default values and
enable them in AP mode.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-05-02 10:28:49 +03:00
Shahar Levi ff86843dfb wl12xx: FM WLAN coexistence
Add support to FM WLAN coexistence (STA only).  Some WiFi harmonics
may interfere with FM operation, to avoid this problem special
coexistence techniques are activated around some FM frequencies.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-05-02 10:26:06 +03:00
Eliad Peller cb5ae0530e wl12xx: configure rates when working in ibss mode
When working in ibss mode, we don't configure rate policy per station
(as we use the same link for multiple stations), so currently the
1mb/s rate is being used.

Instead, configure the firmware to use the whole 11b rates by default.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-05-02 10:26:02 +03:00
Arik Nemtsov 47684808fd wl12xx: support FW TX inactivity triggers
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.

In STA mode we register only for the MAX_TX_RETRY event. A TX failure is
interpreted as a loss of connection.

Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid
the inherent race condition of a mac80211 TX failure counter in addition
to the FW counter.

This patch depends on "mac80211: allow low level driver to report packet
loss"

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28 14:50:45 -04:00
Luciano Coelho 4ec23d6e13 wl12xx: remove unused conf_radio_params structure
This structure has not been used anymore since commit
e6b190ff3c.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:23 +03:00
Luciano Coelho afb7d3cd80 wl12xx: move hardcoded hci_io_ds value into the conf struct
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.

Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:22 +03:00
Shahar Levi 13b107dd98 wl12xx: 1281/1283 support - use dynamic memory for the RX/TX pools
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.

This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.

Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.

[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:48:59 +03:00
Shahar Levi 5aa42346bb wl12xx: 1281/1283 support - Add Definitions
Definitions to support wl128x:
  - New FW file name
  - Chip ID
  - New PLL Configuration Algorithm macros that will be used at wl128x
    boot stage
  - Rename NVS macro name: wl127x and wl128x are using the same NVS
    file name. However, the ini parameters between them are
    different. The driver will validate the correct NVS size in
    wl1271_boot_upload_nvs().

[Cleaned up some of the definitions. -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:46 +03:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Eliad Peller fe5ef09066 wl12xx: use the conf struct instead of macros for memory configuration
make the configuration management more flexible by using the
conf struct, rather than predefined macros.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Eliad Peller c8bde24342 wl12xx: move to new firmware (6.1.3.50.49)
This patch adds support for the new wl12xx firmware (Rev 6.1.3.50.49)

Since this fw is not backward compatible with previous fw versions,
a new fw (with different name) is being fetched.

(the patch is big because it contains all the required fw api changes.
splitting it into multiple patches will result in corrupted intermediate
commits)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Eliad Peller ee60833a4f wl12xx: mcp2.5 - add config_ps acx
mcp2.5 uses this acx to configure the fw only once, rather than
passing the params in every enter psm command.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Juuso Oikarinen ea45b2cbf5 wl12xx: Increase scan channel dwell time for passive scans
The passive scan channel dwell time currently used is 30-60TU. A typical
beacon interval for AP's is 100TU. This leads to a ~30% worst-case probability
of finding an AP via passive scanning.

For 5GHz bands for DFS frequencies passive scanning is the only scanning
option. Hence for these, the probability of finding an AP is very low.

To fix this, increase the passive channel scan dwell times (also the early
leave value, as 5GHz channels are still typically very silent.) Use a value
of 100TU, because that covers most typical AP configurations.

Based on testing the probability of finding an AP (100TU beacon interval) on
a single scan round are as follows (based on 100 iterations):

dwell min/max (TU)   | probability
---------------------+------------
30/60                | 35%
60/60                | 56%
80/80                | 77%
100/100              | 100%

Total scan times now and after the change:

Region | Before (s) | After (s)
-------+------------+----------
00     | 0.77       | 1.48
FI     | 0.95       | 2.01
US     | 0.91       | 1.76

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 23:34:33 +02:00
Levi, Shahar 4b7fac77b4 wl12xx: BA initiator support
Add 80211n BA initiator session support wl1271 driver.
Include BA supported FW version auto detection mechanism.
BA initiator session management included in FW independently.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:58:20 +02:00
Arik Nemtsov 79b223f4c7 wl12xx: AP mode - AP specific CMD_CONFIGURE sub-commands
Add AP max retries and rate policy configuration.
Rename STA rate policy configuration function.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:46 +02:00
Arik Nemtsov 1e05a81888 wl12xx: Add AP related configuration to conf_drv_settings
Rate class configuration has been split up for AP and STA modes.
Template related configuration likewise separated.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:46 +02:00
Shahar Levi 00d201001b wl1271: Change wl12xx Files Names
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:09 +02:00