Support for this machine was just removed, so drop the now unused i2c
bus driver, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Upon a communication error, the interrupt handler can call
tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen
unless the current transaction was marked atomic. Fix this by
making the poll happen atomically if we are in an IRQ.
This matches the behavior prior to the patch mentioned
in the Fixes tag.
Fixes: ede2299f71 ("i2c: tegra: Support atomic transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When copying memory from one buffer to another, instead of open-coding
loops with byte-by-byte copies let's use memcpy() which might be a bit
faster and makes intent more clear.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for I2C bus frequency setting according to the specific
system capability. This capability is obtained from CPLD frequency
setting register, which could be provided through the platform data.
If such register is provided, it specifies minimal I2C bus frequency
to be used for the devices attached to the I2C bus. Supported
freqeuncies are 100KHz, 400KHz, 1MHz, while 100KHz is the default.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Let MODULE_LICENCE match the SPDX header which is correctly based on the
previous textual description.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add code to handle IS_S_RX_FIFO_FULL_SHIFT interrupt to support
master write request with >= 64 bytes.
Iproc has a slave rx fifo size of 64 bytes.
Rx fifo full interrupt (IS_S_RX_FIFO_FULL_SHIFT) will be generated
when RX fifo becomes full. This can happen if master issues write
request of more than 64 bytes.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle single or multi byte master read request with or without
repeated start.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Update slave isr mask (ISR_MASK_SLAVE) to include remaining
two slave interrupts.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle only slave interrupts which are enabled.
The IS_OFFSET register contains the interrupt status bits which will be
set regardless of the enabling of the corresponding interrupt condition.
One must therefore look at both IS_OFFSET and IE_OFFSET to determine
whether an interrupt condition is set and enabled.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle Master aborted error by flushing tx and rx fifo
and reinitializing the hw.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
'flags' and 'io' are needed first, so they should be at the beginning of
the private struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_device_unregister() is NULL-aware and thus doesn't required a
duplication check in i801_del_mux(). Besides that it's also error pointer
aware, and we may drop unneeded assignment in i801_add_mux() followed by
conversion to PTR_ERR_OR_ZERO() for the returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since gpiod_remove_lookup_table() is NULL-aware, no need to have this check
in the caller. Drop duplicate NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 2000 usec to 400
usec. It greatly improves performance of I2C transactions.
Reliability of setting polling time to 400 usec has been thoroughly
validated across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c_new_client_device() already prints an error when it fails. Some
ACPI tables contain 2 ACPI devices describing the same i2c-client,
leading to errors like this:
[ 1.620847] i2c i2c-4: Failed to register i2c client MAGN0001:00 at 0x1d (-16)
[ 1.620870] i2c i2c-4: failed to add I2C device MAGN0001:00 from ACPI
There is nothing we can do about the first -EBUSY error being logged,
but the second error does not really add any new information, so lets
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
gpiod_add_lookup_table() expects the gpiod_lookup_table->table passed to
it to be terminated with a zero-ed out entry.
So we need to allocate one more entry then we will use.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
* pm-sleep:
PM: sleep: Add dev_wakeup_path() helper
PM / suspend: fix kernel-doc markup
PM: sleep: Print driver flags for all devices during suspend/resume
* pm-acpi:
PM: ACPI: Refresh wakeup device power configuration every time
PM: ACPI: PCI: Drop acpi_pm_set_bridge_wakeup()
PM: ACPI: reboot: Use S5 for reboot
* pm-domains:
PM: domains: create debugfs nodes when adding power domains
PM: domains: replace -ENOTSUPP with -EOPNOTSUPP
* powercap:
powercap: Adjust printing the constraint name with new line
powercap: RAPL: Add AMD Fam19h RAPL support
powercap: Add AMD Fam17h RAPL support
powercap/intel_rapl_msr: Convert rapl_msr_priv into pointer
x86/msr-index: sort AMD RAPL MSRs by address
A driver remove callback is only called if the device was bound before.
So it's sure that both dev and dev->driver are valid and dev is an i2c
device. If the check fails something louder than "return 0" might be
appropriate because the problem is grave (something like memory
corruption), otherwise the check is useless.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver core ignores the return value of struct bus_type::remove. So
warn if there is an error that went unnoticed before and return 0
unconditionally in i2c_device_remove().
This prepares changing struct bus_type::remove to return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: added a comment and removed unneeded initializtion]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
For the sake of consistency add leading 0 to first register offsets
to make them all of the same width.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently header file uses partially BIT() and GENMASK() macros.
Switch it to use those macros in all cases where it's applicable
for the sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Starting with
commit 75820314de ("i2c: core: add generic I2C GPIO recovery")
GPIO bus recovery is supported by the I2C core, so we can remove the
driver implementation and use that one instead.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a driver tries to send an I2C message while the adapter is
suspended, this typically fails with:
i2c-sh_mobile e60b0000.i2c: Transfer request timed out
Avoid accessing the adapter while it is suspended by marking it
suspended during suspend. This allows the I2C core to catch this, and
print a warning:
WARNING: CPU: 1 PID: 13 at drivers/i2c/i2c-core.h:54
__i2c_transfer+0x4a4/0x4e4
i2c i2c-6: Transfer while suspended
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add S500 variant to the list of devices supported by the Actions Semi
Owl I2C driver.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_ioremap and ioremap may return NULL which cannot be checked
by IS_ERR.
Signed-off-by: Wang Xiaojun <wangxiaojun11@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If this is not enabled, the interfaces used in this driver do not work:
drivers/i2c/busses/i2c-mlxbf.c:1888:3: error: implicit declaration of function 'i2c_slave_event' [-Werror,-Wimplicit-function-declaration]
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1888:26: error: use of undeclared identifier 'I2C_SLAVE_WRITE_REQUESTED'
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1890:32: error: use of undeclared identifier 'I2C_SLAVE_WRITE_RECEIVED'
ret = i2c_slave_event(slave, I2C_SLAVE_WRITE_RECEIVED,
^
drivers/i2c/busses/i2c-mlxbf.c:1892:26: error: use of undeclared identifier 'I2C_SLAVE_STOP'
i2c_slave_event(slave, I2C_SLAVE_STOP, &value);
^
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Expand the driver to support I2C_SMBUS_BLOCK_PROC_CALL since
HW supports it already.
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mario Alejandro Posso Escobar <mario.posso.escobar@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() on an error.
In case of i2c ocores this leads to a false-positive error being logged:
[ 4.173989] 007: ocores-i2c ocores-i2c: IRQ index 0 not found
i2c ocores already handles the case when the IRQ cannot be found and
therefore there is no benefit in having this error message being logged.
This commit switches to platform_get_irq_optional(), which does not log
in case the IRQ cannot be found.
Signed-off-by: Stefan Lässer <stefan.laesser@omicronenergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A combination of recent bug fixes by Doug Anderson and the proper
definition of iommu streams means that this hack is no longer needed.
Let's clean up the code by reverting '127068abe85b ("i2c: qcom-geni:
Disable DMA processing on the Lenovo Yoga C630")'.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Caleb Connolly <caleb@connolly.tech>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-mxs driver only runs on DT-platform and there is no
need to use the platform_device_id structure to pass the driver
data.
Get rid of it to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
io_base and io_size are assigned to only in .probe() and otherwise unused.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After the commit c5eb119007 ("PCI / PM: Allow runtime PM without callback
functions") we no more need empty stubs for runtime-pm to work.
The driver has no device specific task(s) for .suspend() . The stub was
placed just for runtime-pm, which can be dropped now.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This adds i2c bus recovery to the mv64xxx driver.
Implement bus recovery to recover from SCL/SDA stuck low.
This uses the generic recovery function, setting the clock/data lines as
GPIO pins, and sending 9 clocks to try and recover the bus.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
[wsa: added some curly braces]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During cci_isr() errors read from register fields belonging to
i2c master1 are currently assigned to the status field belonging to
i2c master0. This patch corrects this error, and always assigns
master1 errors to the status field of master1.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add dev_wakeup_path() helper to avoid to spread
dev->power.wakeup_path test in drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes we would get the following flow when doing an i2cset:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
I2C_SLAVE_WRITE_RECEIVED
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
I2C_SLAVE_WRITE_REQUESTED
I2C_SLAVE_WRITE_RECEIVED
Documentation/i2c/slave-interface.rst says that I2C_SLAVE_WRITE_REQUESTED,
which is mandatory, should be sent while the data did not arrive yet. It
means in a write-request I2C_SLAVE_WRITE_REQUESTED should be reported
before any I2C_SLAVE_WRITE_RECEIVED.
By the way, I2C_SLAVE_STOP didn't be reported in the above case because
DW_IC_INTR_STAT was not 0x200.
dev->status can be used to record the current state, especially Designware
I2C controller has no interrupts to identify a write-request. This patch
makes not only I2C_SLAVE_WRITE_REQUESTED been reported first when
IC_INTR_RX_FULL is rising and dev->status isn't STATUS_WRITE_IN_PROGRESS
but also I2C_SLAVE_STOP been reported when a STOP condition is received.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If some bits were cleared by i2c_dw_read_clear_intrbits_slave() in
i2c_dw_isr_slave() and not handled immediately, those cleared bits would
not be shown again by later i2c_dw_read_clear_intrbits_slave(). They
therefore were forgotten to be handled.
i2c_dw_read_clear_intrbits_slave() should be called once in an ISR and take
its returned state for all later handlings.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The Mellanox BlueField I2C controller is only present on Mellanox
BlueField SoCs. Hence add a dependency on MELLANOX_PLATFORM, to prevent
asking the user about this driver when configuring a kernel without
Mellanox platform support.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the email addresses of the author and the maintainer
of the Mellanox BlueField I2C driver.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reference clock frequency remains the same across Bluefield
products. Thus, update the frequency and rename the macro.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Few wrapper functions are useless and can be inlined. So
delete mlxbf_i2c_read() and mlxbf_i2c_write() and replace
them with readl() and writel(), respectively. Also delete
mlxbf_i2c_read_data() and mlxbf_i2c_write() and replace
them with ioread32be() and iowrite32be(), respectively.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The build fails with "implicit declaration of function
'acpi_device_uid'" error. Thus, protect ACPI function calls
from being called when CONFIG_ACPI is disabled.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implements atomic transfers to fix reboot/shutdown on r8a7790 Lager and
similar boards.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: some whitespace fixing]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq never returns 0. Don't check for this. Make it clear that
the error path always returns a negative error code.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If platform_get_irq returns an error, relay this error to the caller of
the probe function. Don't change all errors to -EINVAL. This breaks the
case where platform_get_irq returns -EPROBE_DEFER.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq already prints an error message if the requested irq
was not found. Don't print another message in the driver.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The FU540-C000 has a broken IRQ and support was added earlier
so that it will operate in polling mode, but seems to work only
in case interrupts property is missing from the i2c0 dt-node.
This should not be the case and the driver should handle polling
mode with the interrupt property present in i2c0 node of the
device tree.
So check if it's the FU540-C000 soc and enable polling mode master
xfers, as the IRQ for this chip is broken.
Fixes commit c45d4ba867 ("i2c: ocores: add polling mode workaround
for Sifive FU540-C000 SoC")
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Speed up the boot process by using the asynchronous probing feature
supported by the recent kernels.
For SBCs based on the Actions Semi S500 SoC, the overall boot time is
expected to be reduced by 200-300 ms.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Atomic transfers are required to properly power off a machine through
an I2C controlled PMIC, such as the Actions Semi ATC260x series.
System shutdown may happen with interrupts being disabled and, as a
consequence, the kernel may hang if the driver does not support atomic
transfers.
This functionality is essentially implemented by polling the FIFO
Status register until either Command Execute Completed or NACK Error
bits are set.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[wsa: rebased to current tree]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit dc6df6e90d ("i2c: at91: remove legacy DMA support") removed legcy
DMA support from the driver. Remove the last use of the definitions from
linux/platform_data/dma-atmel.h and stop including this header.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[wsa: fixed typo in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 02b9aec592.
As talked about in the patch ("soc: qcom: geni: More properly switch
to DMA mode"), swapping the order of geni_se_setup_m_cmd() and
geni_se_xx_dma_prep() can sometimes cause corrupted transfers. Thus
we traded one problem for another. Now that we've debugged the
problem further and fixed the geni helper functions to more disable
FIFO interrupts when we move to DMA mode we can revert it and end up
with (hopefully) zero problems!
To be explicit, the patch ("soc: qcom: geni: More properly switch
to DMA mode") is a prerequisite for this one.
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.2.I7b22281453b8a18ab16ef2bfd4c641fb1cc6a92c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af4 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit fa4d305568. An updated
version was sent. So, revert this version and give the new version more
time for testing.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
SCL rate appears to be different than what is expected. For example,
We get 164kHz on i2c3 of the vim3 when 400kHz is expected. This is
partially due to the peripheral clock being disabled when the clock is
set.
Let's keep the peripheral clock on after probe to fix the problem. This
does not affect the SCL output which is still gated when i2c is idle.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use proper spelling of "NVIDIA" and don't designate driver as Tegra2-only
since newer SoC generations are supported as well.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some places in the code are missing newlines or have unnecessary
whitespaces and newlines. This creates inconsistency of the code and
hurts readability. This patch removes the unnecessary and adds necessary
whitespaces / newlines, clears indentation of the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make all comments to be consistent in regards to capitalization and
punctuation, correct spelling and grammar errors, improve wording.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch unifies style of all messages in the driver by starting them
with a lowercase letter and using consistent capitalization and wording
for all messages.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rename "ret" variables to "err" in order to make code a bit more
expressive, emphasizing that the returned value is an error code.
Same vice versa, where appropriate.
Rename variable "reg" to "val" in order to better reflect the actual
usage of the variable in the code and to make naming consistent with
the rest of the code.
Use briefer names for a few members of the tegra_i2c_dev structure in
order to improve readability of the code.
All dev/&pdev->dev are replaced with i2c_dev->dev in order to have uniform
code style across the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reorder definition of variables in the code to have them sorted by length
and grouped logically, also replace "unsigned long" with "u32". Do this in
order to make code easier to read.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver's code is inconsistent in regards to the error values checking.
The correct way should be to check both positive and negative values.
This patch cleans up the error-checks in the code. Note that the
pm_runtime_get_sync() could return positive value on success, hence only
relevant parts of the code are changed by this patch.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out hardware initialization into a separate function from the probe
function. The only place where runtime PM needs to be resumed during probe
is the place of hardware initialization, hence it makes sense to factor
out it in order to have a bit cleaner error handling in tegra_i2c_probe().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out register polling into a separate function in order to remove
boilerplate code and make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The code related to packet header setting up is a bit messy and makes
tegra_i2c_xfer_msg() more difficult to read than it could be. Let's
factor the packet header setup from tegra_i2c_xfer_msg() into separate
function in order to make code easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out error recovery code from tegra_i2c_xfer_msg() in order to
make this function easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop '_timeout' postfix from the wait/poll completion function names in
order to make the names shorter, making code cleaner a tad.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "dma" variable of tegra_i2c_xfer_msg() function doesn't bring much in
regards to readability and generation of the code.
Besides readability, it's also not very nice that the is_curr_dma_xfer
is initialized in tegra_i2c_xfer_msg() and then could be overridden by
tegra_i2c_config_fifo_trig(). In a result, the "dma" variable creates
slight confusion since it's not instantly obvious why it's set after
tegra_i2c_config_fifo_trig().
Hence should be better to have the variable removed. This makes code
more consistent.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tegra_i2c_wait_for_config_load() checks for 'has_config_load_reg' by
itself, hence there is no need to duplicate the check.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The likely/unlikely annotations should be used only in a hot paths of
performance-critical code. The I2C driver doesn't have such paths, and
thus, there is no justification for usage of likely/unlikely annotations
in the code. Hence remove them.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The barrier() was intended to reduce possibility of racing with the
interrupt handler, but driver's code evolved significantly and today's
driver enables interrupt only when it waits for completion notification.
Hence barrier() has no good use anymore, let's remove it.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Don't use signed types for unsigned values and use consistent types
for sibling variables.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reorder location of functions in the code in order to have definition
of functions closer to the place of the invocation. This change makes
easier to navigate around the code and removes the need to have a
prototype for tegra_i2c_init().
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver's probe function code is a bit difficult to read. This patch
reorders code of the probe function, forming groups of code that are easy
to work with. The probe tear-down order now matches the driver-removal
order.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move out code related to device-tree parsing from the probe function into
tegra_i2c_parse_dt() in order to make code more consistent.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Uwe Kleine-König