Add phylib support for the Marvell Alaska X 10 Gigabit PHY (MV88X3310).
This phy is able to operate at 10G, 1G, 100M and 10M speeds, and only
supports Clause 45 accesses.
The PHY appears (based on the vendor IDs) to be two different vendors
IP, with each devad containing several instances.
This PHY driver has only been tested with the RJ45 copper port, fiber
port and a Marvell Armada 8040-based ethernet interface.
It should be noted that to use the full range of speeds, MAC drivers
need to also reconfigure the link mode as per phydev->interface, since
the PHY automatically changes its interface mode depending on the
negotiated speed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for Cortina PHY drivers. Support only CS4340 for now.
The phys are not compatible with IEEE 802.3 clause 22/45 registers.
Implement proper read_status support. The generic 10G phy driver causes
bus register access errors.
The driver should be described using the "ethernet-phy-id" device tree
compatible.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:
- descend into drivers/net/phy/ unconditionally
- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
which allows us not to expose the internal MDIO board info list and
mutex, yet maintain the logic within the same file
- relocate the code that creates a MDIO device into
drivers/net/phy/mdio_bus.c
- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
defined (y or m)
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for gmiitorgmii converter.
The GMII to RGMII IP core provides the Reduced Gigabit Media
Independent Interface (RGMII) between Ethernet physical media
Devices and the Gigabit Ethernet controller. This core can
Switch dynamically between the three different speed modes of
Operation by configuring the converter register through mdio write.
MDIO interface is used to set operating speed of Ethernet MAC.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SGMII based 1G rely on the hardware registers for link state
and sometimes it's not reliable. To get most accurate link state, this
interface has to use the MDIO bus to poll the PHY.
In X-Gene SoC, MDIO bus is shared across RGMII and SGMII based 1G
interfaces, so adding this driver to manage MDIO bus. This driver
registers the mdio bus and registers the PHYs connected to it.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.
This multiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Intel (former Lantiq) XWAY 11G and 22E PHYs.
These PHYs are also named PEF 7061, PEF 7071, PEF 7072.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cavium Thunder SoCs have multiple MIDO buses that are part of a
single PCI device. To model this in the device tree we call the PCI
parent device a "cavium,thunder-8890-mdio-nexus", it has several
children, one for each MDIO bus.
The MDIO bus hardware is identical to that found in the OCTEON SoCs,
so we use that code for things that are not part of the PCI driver
probe/remove
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-on patch uses PCI probing to find the Thunder MDIO hardware.
In preparation for this, split out the common code into a new file
mdio-cavium.c, which will be used by both the existing OCTEON driver,
and the new Thunder PCI based driver.
As part of the refactoring simplify the struct cavium_mdiobus by
removing fields that are only ever used in the probe function and can
just as well be local variables.
Use readq/writeq in preference to readq_relaxed/writeq_relaxed as the
relaxed form was an optimization for an early chip revision, and the
MDIO drivers are not performance bottlenecks that need optimization in
the first place.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83848 Ethernet PHY device.
The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant
single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting
the MII and RMII interfaces.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom iProc MDIO bus interface.
The MDIO interface can be found in the Broadcom iProc family Soc's.
The MDIO bus is accessed using a combination of command and data
registers. This MDIO driver provides access to the Etherent GPHY's
connected to the MDIO bus.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Microchip LAN88XX phy driver for phylib.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Teranetics TN2020 is compliant with IEEE 802.3an 10 Gigabit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we get things like:
warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)
In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
This patch adds an MDIO driver which handles the MII bus.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Frederic Lambert <frdrc66@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This is the first version of phy driver from Micrel Inc.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King