The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the correct software reset sequence for 58xx devices by
setting all 3 reset bits and polling for the SW_RST bit to clear itself
without a given timeout. We cannot use is58xx() here because that would
also include the 7445/7278 Starfighter 2 which have their own driver
doing the reset earlier on due to the HW specific integration.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Broadcom tags are not enabled in b53 (DSA_PROTO_TAG_NONE), we need
to make sure that the IMP/CPU port is included in the forwarding
decision.
Without this change, switching between non-management ports would work,
but not between management ports and non-management ports thus breaking
the default state in which DSA switch are brought up.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_I2C=m and NET_DSA_SMSC_LAN9303=y, we run into a link error:
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_read':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_read+0x18): undefined reference to `i2c_smbus_read_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_write':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_write+0x18): undefined reference to `i2c_smbus_write_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_reg_read':
regmap-i2c.c:(.text.regmap_smbus_word_reg_read+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_read_swapped':
regmap-i2c.c:(.text.regmap_smbus_word_read_swapped+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_write_swapped':
This adds a Kconfig dependency to avoid the broken configuration.
Fixes: be4e119f99 ("net: dsa: LAN9303: add I2C managed mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the LAN9303 device is in MDIO manged mode, all register accesses must
be done via MDIO.
Please note: this code is compile time tested only due to the absence of such
configured hardware. It is based on a patch from Stefan Roese from 2014.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
CC: sr@denx.de
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this mode the switch device and the internal phys will be managed via
I2C interface. The MDIO interface is still supported, but for the
(emulated) CPU port only.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMSC/Microchip LAN9303 is an ethernet switch device with one CPU port
and two external ethernet ports with built-in phys.
This driver uses the DSA framework, but is currently only capable of
separating the two external ports. There is no offload support yet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build errors seen with CONFIG_GPIOLIB disabled and warnings enabled:
drivers/net/dsa/mt7530.c: In function 'mt7530_setup':
drivers/net/dsa/mt7530.c:948:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(priv->reset, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c: In function 'mt7530_probe':
drivers/net/dsa/mt7530.c:1068:17: error: implicit declaration of function 'devm_gpiod_get_optional' [-Werror=implicit-function-declaration]
priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13:
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI clause 22 & 45 read/write operations are local to the global2.c file,
so make them static. This eliminates the following warning:
drivers/net/dsa/mv88e6xxx/global2.c:571:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:602:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:635:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:664:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.
For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.
The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static checker reported the following:
drivers/net/dsa/dsa_loop.c:223 dsa_loop_port_vlan_dump()
error: uninitialized symbol 'err'.
which could happen if we do hit the continue statement for each iteration of
the loop. Initialize err to 0 here.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static analyzer reported the following:
drivers/net/dsa/dsa_loop.c:181 dsa_loop_port_vlan_del()
error: XXX uninitialized symbol 'pvid'.
we were missing the assignment of pvid to ps->vid, so add that.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a DSA mock-up driver which essentially does
the following:
- registers/unregisters 4 fixed PHYs to the slave network devices
- uses eth0 (configurable) as the master netdev
- registers the switch as a fixed MDIO device against the fixed MDIO bus
at address 31
- includes dynamic debug prints for dsa_switch_ops functions that can be
enabled to get call traces
This is a good way to test modular builds as well as exercise the DSA
APIs without requiring access to real hardware. This does not test the
data-path, although this could be added later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA cross-chip bridging operations by remapping the local
ports an external source port can egress frames to, when this cross-chip
port joins or leaves a bridge.
The PVT is no longer configured with all ones allowing any external
frame to egress any local port. Only DSA and CPU ports, as well as
bridge group members, can egress frames on local ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a local port of a switch chip becomes a member of a bridge group,
we need to reprogram the Cross-chip Port Based VLAN Table (PVT) to allow
existing cross-chip bridge members to egress frames on the new ports.
There is no functional changes yet, since the PVT is still programmed
with all ones, allowing any external port to egress frames locally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factorize the code in the DSA port_bridge_{join,leave} routines used to
program the port VLAN map of all local ports of a given bridge group.
At the same time shorten the _mv88e6xxx_port_based_vlan_map to get rid
of the old underscore prefix naming convention.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ports -- internal and external, for chips featuring a PVT -- have a
mask restricting to which internal ports a frame is allowed to egress.
Now that DSA exposes the number of ports and their bridge devices, it is
possible to extract the code generating the VLAN map and make it generic
so that it can be shared later with the cross-chip bridging code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allocates DSA_MAX_PORTS ports for a Marvell dsa_switch
structure. Provide the exact number of ports so the corresponding
ds->num_ports is accurate.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.
This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.
Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.
Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).
Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.
Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU ageing time value programmed in the switch is rounded up to the
nearest multiple of its coefficient (variable depending on the model.)
Add a debug message to inform the user about the exact programmed value.
On 6352, "brctl setageing br0 18" gives "AgeTime set to 0x01 (15000 ms)"
while on 6390 we get "AgeTime set to 0x05 (18750 ms)".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the trunk member of the mv88e6xxx_atu_entry structure regardless its
value, so that uninitialized structures gets the correct boolean value.
Note that no mainline code is affected by the current behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 does require the MDIO_BCM_UNIMAC driver which is now dependent
on OF_MDIO but also internally uses of_mdio.c provided routines which
are guarted with OF_MDIO.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA has ageing time limits, specify them when registering a
switch so that out-of-range values are handled correctly by the core.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reported-by: Jason Cobham <jcobham@questertangent.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the DA, SA and VTU priority override.
Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.
Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the limiting of learnt MAC addresses.
Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.
Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).
Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".
The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).
Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.
Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.
Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.
Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.
Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.
Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.
All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Flush/Move operation.
Use it to replace the current ATU Flush operation.
_mv88e6xxx_atu_flush_move is still used by the Move operation so keep it
until the Move operation is refactored in a next commit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use a fresh documented implementation of the ATU GetNext.
Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.
Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.
The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.
Add and use a fresh documented implementation of the ATU Load/Purge.
The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.
This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".
This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.
That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6097 chip requires watchdog_ops to be set.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ops needed to support the watchdog for the MV88E6390
family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.
The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it out from the middle for the #defines to just before it is
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't affect how the code works.
My static checker complains that the mask and shift doesn't make sense
because 0xffffff << 16 goes beyond the end of 32 bits. It should be
0xffff instead but the existing code won't cause runtime bugs.
Also the casting here is not needed and not consistent with the rest of
the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 MDIO bus controllers can support for clause 45 accesses.
The internal SERDES interfaces need this, and it is likely external
10GHz PHYs will be clause 45.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enable 2.5Gbps mode, we need the base speed of 10G, plus
the Alt bit setting. Fix a typ0 that used 1Gb base speed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7318166cac ("net: dsa: bcm_sf2: Add support for
ethtool::rxnfc") added a new object to build: bcm_sf2_cfp.o, but in
doing so, we essentially just built this object and no longer bcm_sf2.o.
Fix this by creating a module named bcm-sf2.ko which links in bcm_sf2.o
and bcm_sf2_cfp.o.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use b53_mirror_add and b53_mirror_del because the Starfighter 2
is register compatible in that specific case.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the different Roboswitch registers relevant for
ingress and egress mirroring.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring classification rules using the
ethtool::rxnfc API. This is useful to program the switch's CFP/TCAM to
redirect specific packets to specific ports/queues for instance. For
now, we allow any kind of IPv4 5-tuple matching.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Compact Field Processor definitions for the Broadcom Starfighter 2
and compatible versions of the switch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all traffic goes to queue 0, re-configure the traffic
classes to quality of service mapping such that priority X maps to queue
X, where X is from 0 through 7.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the infrastructure in place, implement access to the external
MDIO bus on the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.
Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.
For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has the internal PHYs mapped directly onto the
SMI register space as the switch. So the registers can be read
directly. Put a wrapper around this, in preparation for changing the
signature in order to support the external MDIO bus of the 6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a bit of boilerplate code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse the "brcm,use-bcm-hdr" boolean property during ports
identification to fill a bitmask of ports that should have Broadcom tags
enabled. This is needed in some configurations where per-packet metadata
can be exchanged using Broadcom tags between the switch and an on-chip
acceleration device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for enabling Broadcom tags on different ports based on
configuration information, dedicate a function that is responsible for
enabling Broadcom tags for a given port and update the IMP port setup to
call it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the integrated switch found on BCM7278:
- core_reg_align is set to 1, to force a translation into the target
address space which is 8 bytes aligned
- an alternate SWITCH_REG layout is provided since registers are largely
bit/masks compatible but have different offsets
- conditional for all CORE_STS_OVERRIDE_{IMP,GMII_P} since those got
moved way out of the traditional register space
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting a new device with a slightly different
register layout, affecting the SWITCH_REG and SWITCH_CORE address
spaces, perform a few preparatory steps:
- allow matching the compatible string against a data description
- convert the SWITCH_REG register accesses into an indirection table
- prepare for supporting a SWITCH_CORE register alignment requirement
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point inlining the 32-bit direct register read/write part,
just infer it from the existing macro. This will make it easier to
centralize the address rewriting that we are going to introduce later
on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.
This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the b53 exported functions to fill our bcm_sf2_ops structure,
also making it clear what we utilize and what we specifically override.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making dsa_switch_ops const, export b53 operations
utilized by other drivers such as bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9a ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the two functions recently introduced: u64_to_ether() and
ether_to_u64() instead of our own versions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip needs MV88E6XXX_FLAG_G2_INT
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup in the ATU can be performed starting from a given MAC
address. This is faster than starting with the first possible MAC
address and iterating all entries.
Entries are returned in numeric order. So if the MAC address returned
is bigger than what we are searching for, we know it is not in the
ATU.
Using the benchmark provided by Volodymyr Bendiuga
<volodymyr.bendiuga@gmail.com>,
https://www.spinics.net/lists/netdev/msg411550.html
on an Marvell Armada 370 RD, the test to add a number of static fdb
entries went from 1.616531 seconds to 0.312052 seconds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices, such as the mv88e6097 do have ADDR[0] external and so it
is possible to configure the device to use SMI address 0x1. Remove the
restriction, as there are boards using this address.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.
Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have different way to issue a software reset.
Old chips (such as 88E6060) have a reset bit in an ATU control register.
Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.
Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper to toggle the eventual GPIO connected to the reset pin.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before resetting a switch, the ports should be set to the Disabled state
and the transmit queues should be drained.
Add an helper to explicit that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DSA_TAG_PROTO_EDSA as tag_protocol for the mv88e6097. The
initialisation was missing before.
Fixes: a1f482aa8c33 ("net: dsa: mv88e6xxx: Move the tagging protocol into info")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.
Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing interrupts requires switch register access to mask the
interrupts. Hence we must hold the register mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible to use devm_request_threaded_irq() because we have
two stacked interrupt controllers in one device. The lower interrupt
controller cannot be removed until the upper is fully removed. This
happens too late with the devm API, resulting in error messages about
removing a domain while there is still an active interrupt. Swap to
using request_threaded_irq() and manage the release of the interrupt
manually.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures may not define IRQ_DOMAIN (like m32r), fixes
undefined references to IRQ_DOMAIN functions.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have a fundamental problem in how we treat the CPU port and
its VLAN membership. As soon as a second VLAN is configured to be
untagged, the CPU automatically becomes untagged for that VLAN as well,
and yet, we don't gracefully make sure that the CPU becomes tagged in
the other VLANs it could be a member of. This results in only one VLAN
being effectively usable from the CPU's perspective.
Instead of having some pretty complex logic which tries to maintain the
CPU port's default VLAN and its untagged properties, just do something
very simple which consists in neither altering the CPU port's PVID
settings, nor its untagged settings:
- whenever a VLAN is added, the CPU is automatically a member of this
VLAN group, as a tagged member
- PVID settings for downstream ports do not alter the CPU port's PVID
since it now is part of all VLANs in the system
This means that a typical example where e.g: LAN ports are in VLAN1, and
WAN port is in VLAN2, now require having two VLAN interfaces for the
host to properly terminate and send traffic from/to.
Fixes: Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII modes delays can be set via strapping pings or EEPROM.
Don't change them unless explicitly asked to change them. The recent
refactoring of setting the MAC configuration changed this behaviours,
in that CPU and DSA ports have any pre-configured RGMII delays
removed. This breaks the Armada 370RD board. Restore the previous
behaviour, in that RGMII delays are only applied/removed when
explicitly asked for via an phy-mode being PHY_INTERFACE_MODE_RGMII*
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have setters to configure the port's MAC, use them to
refactor the port setup and adjust_link code.
Note that port's MAC speed, duplex or RGMII delay must not be changed
unless the port's link is forced down. So wrap all that in a
mv88e6xxx_port_setup_mac function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the two bits for link, duplex or RGMII delays are used the same
way on chips supporting the said feature, the two bits for speed have
different meaning for most of the chips out there.
Speed value is stored in bits 1:0, 0x3 means unforce (normal detection).
Some chips reuse values for alternative speeds when bit 12 is set.
Newer chips with speed > 1Gbps reuse value 0x3 thus need a new bit 13.
Here are the values to write in register 0x1 to (un)force speed:
| Speed | 88E6065 | 88E6185 | 88E6352 | 88E6390 | 88E6390X |
| ------- | ------- | ------- | ------- | ------- | -------- |
| 10 | 0x0000 | 0x0000 | 0x0000 | 0x2000 | 0x2000 |
| 100 | 0x0001 | 0x0001 | 0x0001 | 0x2001 | 0x2001 |
| 200 | 0x0002 | NA | 0x1001 | 0x3001 | 0x3001 |
| 1000 | NA | 0x0002 | 0x0002 | 0x2002 | 0x2002 |
| 2500 | NA | NA | NA | 0x3003 | 0x3003 |
| 10000 | NA | NA | NA | NA | 0x2003 |
| unforce | 0x0003 | 0x0003 | 0x0003 | 0x0000 | 0x0000 |
This patch implements a generic mv88e6xxx_port_set_speed() function used
by chip-specific wrappers to filter supported ports and speeds.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.
Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.
Implement such operation to use it later when setting duplex, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to set the port 802.1Q mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to access the ports default VID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to port files to access the ports default FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli