Take back ownership of the MSIX vectors when unregistering the device
from bnxt_re.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of TX rings is changed in bnxt_setup_tc(), we need to
include the XDP rings in the total TX ring count.
Fixes: 3841340627 ("bnxt_en: Add support for XDP_TX action.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completion may happen any time after HW queue was kicked.
We can't access the skb afterwards. Move the time stamping
before ringing the doorbell.
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a muxed frame, but it can't find the representor
netdev it is destined to it will try to "drop" that frame, i.e. reuse
the buffer. The issue is that the replacement buffer has already been
allocated at this point, and reusing the buffer from received frame
will leak it. Change the code to put the new buffer on the ring
earlier and not reuse the old buffer (make the buffer parameter
to nfp_net_rx_drop() a NULL).
Fixes: 91bf82ca9e ("nfp: add support for tx/rx with metadata portid")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
App start/stop callbacks can perform application initialization.
Unfortunately, flower app started using them for creating and
destroying representors. This can lead to a situation where
lower vNIC netdev is destroyed while representors still try
to pass traffic. This will most likely lead to a NULL-dereference
on the lower netdev TX path.
Move the start/stop callbacks, so that representors are created/
destroyed when vNICs are fully initialized.
Fixes: 5de73ee467 ("nfp: general representor implementation")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling SR-IOV VFs will cause the PCI subsystem to schedule a
work and flush its workqueue. Since the nfp driver schedules its
own work we can't enable VFs while holding driver load. Commit
6d48ceb27a ("nfp: allocate a private workqueue for driver work")
tried to avoid this deadlock by creating a separate workqueue.
Unfortunately, due to the architecture of workqueue subsystem this
does not guarantee a separate thread of execution. Luckily
we can simply take pci_enable_sriov() from under the driver lock.
Take pci_disable_sriov() from under the lock too for symmetry.
Fixes: 6d48ceb27a ("nfp: allocate a private workqueue for driver work")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MII/GMII/SGMII in the Altera SoC, the phy needs to be
wired through the FPGA. To ensure correct behavior, the appropriate
bit in the System Manager FPGA Interface Group register needs to be
set.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps tools such as wpa_supplicant can start even if the macsec
module isn't loaded yet.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the value of the mrouter flag in struct mlxsw_sp_bridge_port when
it is being changed.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_4k_uar module parameter was added in patch cited below to
address the backward compatibility issue in SRIOV when the VM has
system's PAGE_SIZE uar implementation and the Hypervisor has 4k uar
implementation.
The above compatibility issue does not exist in the non SRIOV case.
In this patch, we always enable 4k uar implementation if SRIOV
is not enabled on mlx4's supported cards.
Fixes: 76e39ccf9c ("net/mlx4_core: Fix backward compatibility on VFs")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller reported a double free [1], caused by the fact
that tun driver was not updated properly when priv_destructor
was added.
When/if register_netdevice() fails, priv_destructor() must have been
called already.
[1]
BUG: KASAN: double-free or invalid-free in selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
CPU: 0 PID: 2919 Comm: syzkaller227220 Not tainted 4.13.0-rc4+ #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
print_address_description+0x7f/0x260 mm/kasan/report.c:252
kasan_report_double_free+0x55/0x80 mm/kasan/report.c:333
kasan_slab_free+0xa0/0xc0 mm/kasan/kasan.c:514
__cache_free mm/slab.c:3503 [inline]
kfree+0xd3/0x260 mm/slab.c:3820
selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
security_tun_dev_free_security+0x48/0x80 security/security.c:1512
tun_set_iff drivers/net/tun.c:1884 [inline]
__tun_chr_ioctl+0x2ce6/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x443ff9
RSP: 002b:00007ffc34271f68 EFLAGS: 00000217 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00000000004002e0 RCX: 0000000000443ff9
RDX: 0000000020533000 RSI: 00000000400454ca RDI: 0000000000000003
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 0000000000401ce0
R13: 0000000000401d70 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 2919:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xaa/0xd0 mm/kasan/kasan.c:551
kmem_cache_alloc_trace+0x101/0x6f0 mm/slab.c:3627
kmalloc include/linux/slab.h:493 [inline]
kzalloc include/linux/slab.h:666 [inline]
selinux_tun_dev_alloc_security+0x49/0x170 security/selinux/hooks.c:5012
security_tun_dev_alloc_security+0x6d/0xa0 security/security.c:1506
tun_set_iff drivers/net/tun.c:1839 [inline]
__tun_chr_ioctl+0x1730/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
Freed by task 2919:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_slab_free+0x6e/0xc0 mm/kasan/kasan.c:524
__cache_free mm/slab.c:3503 [inline]
kfree+0xd3/0x260 mm/slab.c:3820
selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
security_tun_dev_free_security+0x48/0x80 security/security.c:1512
tun_free_netdev+0x13b/0x1b0 drivers/net/tun.c:1563
register_netdevice+0x8d0/0xee0 net/core/dev.c:7605
tun_set_iff drivers/net/tun.c:1859 [inline]
__tun_chr_ioctl+0x1caf/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
The buggy address belongs to the object at ffff8801d2843b40
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 0 bytes inside of
32-byte region [ffff8801d2843b40, ffff8801d2843b60)
The buggy address belongs to the page:
page:ffffea000660cea8 count:1 mapcount:0 mapping:ffff8801d2843000 index:0xffff8801d2843fc1
flags: 0x200000000000100(slab)
raw: 0200000000000100 ffff8801d2843000 ffff8801d2843fc1 000000010000003f
raw: ffffea0006626a40 ffffea00066141a0 ffff8801dbc00100
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801d2843a00: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
ffff8801d2843a80: 00 00 00 fc fc fc fc fc fb fb fb fb fc fc fc fc
>ffff8801d2843b00: 00 00 00 00 fc fc fc fc fb fb fb fb fc fc fc fc
^
ffff8801d2843b80: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
ffff8801d2843c00: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
==================================================================
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop counter k is currently being decremented from zero which
is incorrect. Fix this by incrementing k instead
Detected by CoverityScan, CID#401847 ("Infinite loop")
Fixes: 83f18a557c ("netxen_nic: fw dump support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop that performs the dma page unmapping never decrements
index counter f and hence loops forever. Fix this with a pre-decrement
on f.
Detected by CoverityScan, CID#1357309 ("Infinite loop")
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC stats command takes a port ID, which doesn't exist on
pre-ef10 NICs (5000- and 6000- series). This is extracted from the
NIC specific data; we misinterpret this as the ef10 data structure,
causing us to read potentially unallocated data. With a KASAN kernel
this can cause errors with:
BUG: KASAN: slab-out-of-bounds in efx_mcdi_mac_stats
Fixes: 0a2ab4d988 ("sfc: set the port-id when calling MC_CMD_MAC_STATS")
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZkte/AAoJEG4XJFUm622bjqUH/01JNHIGh7WI2YHm9qA//uC0
L35j/nYwiBX47LREkVhgS2goR3BYihricM1w1uwv/1E/JJqECWVe7rPodoM4sYqh
jVVPy3ZYIK/Kk8i7v2W+VIeqR0b2q4PBt+UtruEBH1o8ESKZPDMqudq+AAbHeiih
tWJpPmS+IFW8yWaF9+v5DhWx5q4/JNvZgmNarS5/aPF+2bTR9Gw0bf8PUdyLip6J
rsv0W9e9SqmVBYkRoC4WMgM/RJbUh1d66SPQ3Yrv/nFL6cTgecC2IxQx7pCGUq9n
LbDJy6HCi+3mBJyMkVVs9iaXZiaNm7eUmEq16ENpiAnsQy5h9i/jVpySC0R/BzQ=
=KXB+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4vf Ethernet driver now queries PCIe configuration space to
determine if it can send TLPs to it with the Relaxed Ordering
Attribute set, just like the pf did.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 Ethernet driver now queries PCIe configuration space to determine
if it can send TLPs to it with the Relaxed Ordering Attribute set.
Remove the enable_pcie_relaxed_ordering() to avoid enable PCIe Capability
Device Control[Relaxed Ordering Enable] at probe routine, to make sure
the driver will not send the Relaxed Ordering TLPs to the Root Complex which
could not deal the Relaxed Ordering TLPs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware feature check introduced for multi-scheduled scan turned out
to be failing for bcm4343{0,1,8} devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
bond_miimon_commit() handles the UP transition for each slave of a bond
in the case of MII. It is triggered 10 times per second for the default
MII Polling interval of 100ms. For device drivers that do not implement
__ethtool_get_link_ksettings() the call to bond_update_speed_duplex()
fails persistently while the MII status could remain UP. That is, in
this and other cases where the speed/duplex update keeps failing over a
longer period of time while the MII state is UP, a warning is printed
every MII polling interval.
To address these excessive warnings net_ratelimit() should be used.
Printing a warning once would not be sufficient since the call to
bond_update_speed_duplex() could recover to succeed and fail again
later. In that case there would be no new indication what went wrong.
Fixes: b5bf0f5b16 (bonding: correctly update link status during mii-commit phase)
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Flower app may receive a request to update the MTU of a representor
netdev upon receipt of a control message from the firmware. This requires
the RTNL lock which needs to be taken outside of the packet processing
path.
As a handling of this correctly seems a little to invasive for a fix simply
skip setting the MTU for now.
Relevant backtrace:
[ 1496.288489] BUG: scheduling while atomic: kworker/0:3/373/0x00000100
[ 1496.294911] dca syscopyarea sysfillrect sysimgblt fb_sys_fops ptp drm mxm_wmi ahci pps_core libahci i2c_algo_bit wmi [last unloaded: nfp]
[ 1496.294918] CPU: 0 PID: 373 Comm: kworker/0:3 Tainted: G OE 4.13.0-rc3+ #3
[ 1496.294919] Hardware name: Supermicro X10DRi/X10DRi, BIOS 2.0 12/28/2015
[ 1496.294923] Workqueue: events work_for_cpu_fn
[ 1496.294924] Call Trace:
[ 1496.294927] <IRQ>
[ 1496.294931] dump_stack+0x63/0x82
[ 1496.294935] __schedule_bug+0x54/0x70
[ 1496.294937] __schedule+0x62f/0x890
[ 1496.294941] ? intel_unmap_sg+0x90/0x90
[ 1496.294942] schedule+0x36/0x80
[ 1496.294943] schedule_preempt_disabled+0xe/0x10
[ 1496.294945] __mutex_lock.isra.2+0x445/0x4a0
[ 1496.294947] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294950] ? kfree+0x162/0x170
[ 1496.294952] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294953] ? iommu_should_identity_map+0x50/0xe0
[ 1496.294954] __mutex_lock_slowpath+0x13/0x20
[ 1496.294955] ? iommu_no_mapping+0x48/0xd0
[ 1496.294956] ? __mutex_lock_slowpath+0x13/0x20
[ 1496.294957] mutex_lock+0x2f/0x40
[ 1496.294960] rtnl_lock+0x15/0x20
[ 1496.294979] nfp_flower_cmsg_rx+0xc8/0x150 [nfp]
[ 1496.294986] nfp_ctrl_poll+0x286/0x350 [nfp]
[ 1496.294989] tasklet_action+0xf6/0x110
[ 1496.294992] __do_softirq+0xed/0x278
[ 1496.294993] irq_exit+0xb6/0xc0
[ 1496.294994] do_IRQ+0x4f/0xd0
[ 1496.294996] common_interrupt+0x89/0x89
Fixes: 948faa46c0 ("nfp: add support for control messages for flower app")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function stmmac_mdio_register() is only used by
stmmac_dvr_probe() from stmmac_main.c, in order to register the MDIO bus
and probe information about the PHY. As this function is called before
calling register_netdev(), all messages logged from stmmac_mdio_register
are prefixed by "(unnamed net_device)". The goal of netdev_info or
netdev_err is to dump useful infos about a net_device, when this data
structure is partially initialized, there is no point for using these
functions.
This commit fixes the issue by replacing all netdev_*() by the
corresponding dev_*() function for logging. The last netdev_info is
replaced by phy_attached_info(), as a valid phydev can be used at this
point.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch c4adfc822b ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822b ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geneve's Virtual Network Identifier (VNI) is 24 bit long, so the range
of values for it would be from 0 to 16777215 (2^24 -1). However, one
cannot create a geneve device with VNI set to 16777215. This patch fixes
this issue.
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.
This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, if a station is removed just as it is adding a new stream,
the queue in question will remain stopped and no more TX will happen
in this queue, leading to connection failures and other problems.
This is because under DQA, when tx is deferred because a queue needs
to be allocated, the mac queue for that TID is stopped until the new
stream is added. If at this point the station that this stream
belongs to is removed, all the deferred tx frames are purged, but the
mac queue is not restarted. As a result, all following tx on this
queue will not be transmitted.
Fix this by starting the relevant mac queues when the deferred tx
frames are purged.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit e5dadc65f9 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.
This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.
Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.
Fixes: e5dadc65f9 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb0 ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.
'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.
Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().
This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.
Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().
Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.
For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.
Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.
Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.
In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().
The risks include:
a) asynchronously freeing rx->ax_skb after passing the netdev buffer
to the NAPI layer which might corrupt the backlog queue.
b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
times which causes writing off the end of the netdev buffer.
Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.
The new code keeps track of the number of open channels and
waits until that many are open.
Other issues here were:
* host might return less sub-channels than was requested.
* the new init status is not valid until after init was completed.
Fixes: b3e6b82a00 ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.
Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.
Fixes: 0db01097ca ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.
SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c815 ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358 ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to handle hard_header_len update
When ifconfig up/down sequence is initiated hard_header_len
get updated incrementally for each ifconfig up /down sequence,
this leads invalid hard_header_len, moving to lan78xx_bind
to have one time update of hard_header_len addresses the issue.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan