dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit dc6df6e90d ("i2c: at91: remove legacy DMA support") removed legcy
DMA support from the driver. Remove the last use of the definitions from
linux/platform_data/dma-atmel.h and stop including this header.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[wsa: fixed typo in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the Microchip at91 driver the first to use the generic GPIO bus
recovery support from the I2C core and discard the driver implementation.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_gpiod_get() usually calls gpio_request_enable() for non-strict pinmux
drivers. These puts the pins in GPIO mode, whithout notifying the pinctrl
driver. At this point, the I2C bus no longer owns the pins. To mux the
pins back to the I2C bus, we use the pinctrl driver to change the state
of the pins to GPIO, before using devm_gpiod_get(). After the pins are
received as GPIOs, we switch theer pinctrl state back to the default
one,
Fixes: d3d3fdcc4c ("i2c: at91: implement i2c bus recovery")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After a transfer timeout, some faulty I2C slave devices might hold down
the SDA pin. We can generate a bus clear command, hoping that the slave
might release the pins.
If the CLEAR command is not supported, we will use gpio recovery, if
available, to reset the bus.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implement i2c bus recovery when slaves devices might hold SDA low.
In this case re-assign SCL/SDA to gpios and issue 9 dummy clock pulses
until the slave release SDA.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for analog filtering for i2c lines.
The sama5d2 and sam9x60 support this feature.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add new platform data support for advanced digital filtering for i2c.
The sama5d2 and sam9x60 support this feature.
This digital filter allows the user to configure the maximum
width of the spikes that can be filtered.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add new platform data support for digital filtering for i2c.
The sama5d4, sama5d2 and sam9x60 support this feature.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a040 ("i2c: at91: add new driver")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The single file i2c-at91.c has been split into core code (i2c-at91-core.c)
and master mode specific code (i2c-at91-master.c). This should enhance
maintainability and reduce ifdeffery for slave mode related code.
The code itself hasn't been touched. Shared functions only had to be made
non-static. Furthermore, includes have been cleaned up.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: fix checkpatch errors and use SPDX]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang