An ADC is often used to measure other quantities indirectly. This
binding describe one cases, a current through a shunt resistor
measured by the voltage over it.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regmap core now handles splitting up transactions according to
max_raw_read, so this code is no longer required in client drivers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Delete the useless ored result and give a second chance to turn
the chip back off at the end.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factorize reading channel data in its own function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_* for iio_triggered_buffer_setup, iio_device_register,
iio_trigger_register. Delete unneeded inv_mpu6050_remove_trigger,
inv_mpu_core_remove, and inv_mpu_remove for spi driver.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some functions are turning the chip on and not back off in error
path. With set_power function using a reference counter that
would keep the chip on forever.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
spi-max-frequency is requested for SPI master mode (only), to tune output
clock. It may happen requested frequency isn't reachable.
Add explicit check, so probe fails with error in this case. Otherwise,
output clock may simply be silently turned off (conversions fail).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
reg property should be checked against number of available filters.
BTW, dfsdm->num_fls wasn't used. But it can be used for this purpose.
This prevents using data out of allocated dfsdm->fl_list array.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Misc fixes & style improvements:
- checkpatch warns about line over 80 characters.
- remove extra spaces and a blank line (e.g. checkpatch --strict)
- remove bad error message always printed in probe routine.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add blank lines to improve readability.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reorders the variable declarations to prefer a reverse Christmas tree
order to improve readability.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patches sorts all the includes in alphabetic order.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patches removes unneeded slab.h header.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The configuration register on the device is represented with the
prox_config member on the tsl2x7x_settings structure. According to the
TSL2772 data sheet, this register can hold: 1) the proximity drive
level, 2) ALS/Proximity long wait, and 3) the ALS gain level. This
patch renames prox_config to als_prox_config since ALS settings can
be stored here as well.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch removes several unnecessary comments, changes some comments
so that the use as much of the allowable 80 characters as possible, adds
the proper whitespace, removes some structure members from the kernel
docs that are no longer present, and improves the existing kernel doc
information for some existing structure members.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch changes the defaults of the als_time, prox_time and
wait_time to match the defaults according to the TSL2772 datasheet.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver mostly uses the 'prox' naming convention for most of the
proximity settings, however prx_time and tsl2x7x_prx_gain was present.
This patch renames these to prox_time and tsl2x7x_prox_gain for
consistency with everything else in the driver.
The kernel documentation for prx_gain is corrected to prox_gain so that
it matches what is actually in the structure.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The power and diode defines are needed for the platform data so this
patch moves the defines out of the .c file and into the header file. A
comment for the diode is also cleaned up while this code is touched.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch renames tsl2x7x_device_id() to tsl2x7x_device_id_verif(),
removes the unnecessary pointer on the id parameter, and only calls
the verification function once.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2x7x_write_interrupt_config() has an unnecessary return value check
at the end of the function. This patch changes the function to just
return the value from the call to tsl2x7x_invoke_change().
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2x7x_suspend() and tsl2x7x_resume() both check to see what the
current chip status is. These checks are not necessary so this patch
removes those checks.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2x7x_clear_interrupts() takes a reg argument but there are only
two callers to this function and both callers pass the same value.
Since this function was introduced, interrupts are now working
properly for this driver, and several unnecessary calls to
tsl2x7x_clear_interrupts() were removed. This patch removes the
tsl2x7x_clear_interrupts() function and replaces the two callers
with the i2c_smbus_write_byte() call instead.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2x7x_event_handler() could return an error and this could cause the
interrupt to remain masked. We shouldn't return an error in the
interrupt handler so this patch always returns IRQ_HANDLED. An error
will be logged if one occurs.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The integration_time* attributes are currently associated with the
IIO_LIGHT channel but should be associated with the IIO_INTENSITY
channel. Directory listing of the sysfs attributes for a TSL2772
with this patch applied:
dev
events
in_illuminance0_calibrate
in_illuminance0_calibscale_available
in_illuminance0_input
in_illuminance0_lux_table
in_illuminance0_target_input
in_intensity0_calibbias
in_intensity0_calibscale
in_intensity0_integration_time
in_intensity0_integration_time_available
in_intensity0_raw
in_intensity1_raw
in_proximity0_calibrate
in_proximity0_calibscale
in_proximity0_calibscale_available
in_proximity0_raw
name
of_node
power
subsystem
uevent
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Lenovo Ideapad Miix 320 uses an st accelerometer with an ACPI id
of SMO8840, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document that the hardware supports falling edge, rising edge, level
low, and level high interrupt types, rather than just rising edge.
The language used is the same as that in st_lsm6dsx.txt.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we support only rising edge interrupts, and in fact we assume
that the interrupt we're given is rising edge (and things won't work if
it's not). However, the device supports rising edge, falling edge, level
low, and level high interrupts.
Empirically, on my system, switching to level interrupts has fixed a
problem I had with significant (~40%) interrupt loss with edge
interrupts. This issue is likely related to the SoC I'm using (Allwinner
H3), but being able to switch the interrupt type is still a very useful
workaround.
I tested this with each interrupt type and verified correct behavior in
a logic analyzer.
Add support for these interrupt types while also eliminating the error
case of the device tree and driver using different interrupt types.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set power function is rewritten manually inside i2c mux select.
Better use the already identical existing function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rewrite set_power_itg. Failing when turning power off is
no more decreasing the counter now and sleeping only happens
when effectively turning the chip on. Fix also usage in init
function (setting power on one time is sufficient to ensure
chip is effectively on).
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the example to use the compatible string including the
vendor prefix instead of the ones deprecated in 3a872138e4.
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'sca3000_configure_ring()' can fail, so test its return value and
propagate it if needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use 'devm_iio_kfifo_allocate()' instead of 'iio_kfifo_allocate()' in order
to simplify code and avoid a memory leak in an error path in
'sca3000_probe()'. A call to 'sca3000_unconfigure_ring()' was missing.
Sent via the next merge window as unimportant bug and there are
other patches dependent on it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5694/AD5694R/AD5695R/AD5696/AD5696R are a family of 4 channel DACs
with 12-bit, 14-bit and 16-bit precision respectively. The devices have
either no built-in reference, or built-in 2.5V reference.
The AD5671R/AD5675R are similar, except that they have 8 instead of 4
channels.
These devices are similar to AD5672R/AD5676/AD5676R and
AD5684/AD5684R/AD5684/AD5685R/AD5686/AD5686R, except that they use i2c
instead of spi.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5671R_5675R.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5696R_5695R_5694R.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In this patch restructures the existing ad5686 driver by adding a module
for SPI and a header file, while the baseline module deals with the
chip-logic.
This is a necessary step, as this driver should support in the future
similar devices which differ only in the type of interface used (I2C
instead of SPI).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver acctually supports the AD5685R device and NOT the AD5685, which
does not exist. Maintain old id entry in case we have devicetrees
out there which are using the wrong name.
More information can be found in the datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5686_5684.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a new num_channels attribute as part of the
ad5686_chip_info struct which replaces the AD5686_DAC_CHANNELS define. This
is a necessary step, since this driver should support similar devices which
differ only in the number of channels.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and remove license notice to keep the whole
purpose of using an SPDx id.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes some indentation issues and does not modify the
functionality of the driver.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for the mpu9255 IMU to the mpu6050 driver. The
register map is the same as the other chips; the only driver
difference is the compatible string and the WHOAMI register
value.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
usleep_range() uses hrtimers and provides no advantage over msleep()
for larger delays.
Cc: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.org/lkml/2017/1/11/377
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to flush fifo and loose all data when the iio
buffer is full. Just drop the data by ignoring the error as
commonly done in other drivers.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Reviewed-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reorder some variable declarations in an inverse-pyramid scheme.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Peter Rosin