This patch allocates memory for DSI encoder and connector
which will be used for various DSI encoder/connector operations
and attaching the same to DRM subsystem. This patch also extracts
DSI modes info from VBT and save the desired mode info to connector.
v2 by Jani:
- Drop GEN11 prefix from encoder name
- Drop extra parenthesis
- Drop extra local variable
- Squash encoder power domain here
v3 by Jani:
- Squash connector and connector helper functions here
- Move intel_dsi_vbt_init call here
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0197023b92ffa2d59064e30fd4ca22b6a4cff16c.1543500286.git.jani.nikula@intel.com
This patch calculates various DPLL dividers and
parameters for DSI encoder and adjust AFE clock
for DSI. For DSI, 8x clock is AFE clock.
v2: Extend haswell_crtc_compute_clock() for Gen11 DSI
v3: Rebase
v4: use port clock instead of bitrate.
v5: Reabse and remove divide by 5
v6 by Jani:
- Fix indent (Madhav)
- Fix dpll state calc for EDP and DP MST
Co-developed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/525d41d0d893dcdc8874d2ce70afa226227ea3f4.1543500285.git.jani.nikula@intel.com
The requirement for the DDI port clock gating for a port in DSI mode is
the opposite wrt. the case when the port is in DDI mode: the clock
should be gated when the port is active and ungated when the port is
inactive. Note that we cannot simply keep the DDI clock gated when the
port will be only used in DSI mode: it must be gated/ungated at a
specific spot in the DSI enable/disable sequence.
Ensure the above for all ports of a DSI encoder, also adding a sanity
check that we haven't registered another encoder using the same port
(VBT should never allow this to happen).
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ceb14d5a68e8e23988d923d4290a4f981789e616.1543500285.git.jani.nikula@intel.com
Unclutter the haswell_crtc_enable() and haswell_crtc_disable() functions
a bit by moving the pll to port mapping and unmapping functions to the
ddi encoder hooks. This allows removal of a bunch of boilerplate code
from the functions.
Additionally, the ICL DSI encoder needs to do the clock gating and
ungating slightly differently, and this allows its own handling in a
clean fashion.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f8e2982ceea4c05dc254a0c15e2b3be1d5f271d3.1543500285.git.jani.nikula@intel.com
Commit b244ffa15c ("drm/i915/gvt: Fix drm_format_mod value for vGPU
plane") introduced a regression issue to the tiled memory decoding on BDW.
This patch can fix this issue.
Here is the issue detail: https://github.com/intel/gvt-linux/issues/61
v1->v2:
- Refine the commit message. (Zhenyu)
Fixes: b244ffa15c8b("drm/i915/gvt: Fix drm_format_mod value for vGPU plane")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As stated in struct drm_encoder, crtc field should only be used
by non-atomic drivers.
So here caching the pipe id in intel_psr_enable() what is way more
simple and efficient than at every call to
intel_psr_flush()/invalidate() get the
drm.mode_config.connection_mutex lock to safely be able to get the
pipe id by reading drm_connector_state.crtc.
This should fix the null pointer dereference crash below as the
previous way to get the pipe id was prone to race conditions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105959
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128072838.22773-1-jose.souza@intel.com
The test was missing some magic ingredients to actually trigger the
resets.
In case of the full reset we need the I915_RESET_HANDOFF flag set, and in
case of engine reset we need a busy request.
Thanks to Chris for helping with reset magic.
v2:
* Grab RPM ref over reset.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130095211.23849-1-tvrtko.ursulin@linux.intel.com
It seems that the documentation does not reference this any more, plus,
bit 28 does not stick when written to the register.
Therefore I can only assume this is something which was documented in the
past but got removed from the hardware in the meantime.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129134630.8222-1-tvrtko.ursulin@linux.intel.com
248 "multiple definition of ...". E.g.:
LD [M] drivers/gpu/drm/i915/i915.o
ld: drivers/gpu/drm/i915/i915_irq.o: in function `intel_opregion_resume':
i915_irq.c:(.text+0x58f0): multiple definition of `intel_opregion_resume';
drivers/gpu/drm/i915/i915_drv.o:i915_drv.c:(.text+0x2d40): first defined here
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: a950adc6c3 ("drm/i915: Stop calling intel_opregion unregister/register in suspend/resume")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build tested
Link: https://patchwork.freedesktop.org/patch/msgid/20181129210543.31555-1-chris@chris-wilson.co.uk
Set the suitable bits in DP_TP_CTL to stop
bit correction when DSC is disabled.
v2:
- rebased.
- Add additional check for compression state. (Gaurav)
v3: rebased.
v4:
- Move the code to the proper spot according to spec (Ville)
- Use proper checks (manasi)
v5: Remove unnecessary checks (Ville)
v6: Resolve warnings. Add crtc_state as an argument to
intel_disable_ddi_buf(). (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-17-manasi.d.navare@intel.com
If FEC is supported, the corresponding
DP_TP_CTL register bits have to be configured.
The driver has to program the FEC_ENABLE in DP_TP_CTL[30] register
and wait till FEC_STATUS in DP_TP_CTL[28] is 1.
Also add the warn message to make sure that the control
register is already active while enabling FEC.
v2:
- Change commit message. Configure fec state after
link training (Manasi, Gaurav)
- Remove redundent checks (Manasi)
- Remove the registers that get added automagically (Anusha)
v3: s/intel_dp_set_fec_state()/intel_dp_enable_fec_state() (Gaurav)
v4: rebased.
v5:
- Move the code to the proper spot, according to spec.(Ville)
- Use fec state as a check too.
v6: Pass intel_encoder, instead of intel_dp. (Ville)
v7: Remove unwanted comments (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-16-manasi.d.navare@intel.com
If the panel supports FEC, the driver has to
set the FEC_READY bit in the dpcd register:
FEC_CONFIGURATION.
This has to happen before link training.
v2: s/intel_dp_set_fec_ready/intel_dp_sink_set_fec_ready
- change commit message. (Gaurav)
v3: rebased. (r-b Manasi)
v4: Use fec crtc state, before setting FEC_READY
bit. (Anusha)
v5: Move to intel_ddi.c
- Make the function static (Anusha)
v6: Dont pass state as a separate argument (Ville)
v7: (From Manasi)
* Correct the debug print (Ville)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-15-manasi.d.navare@intel.com
For DP 1.4 and above, Display Stream compression can be
enabled only if Forward Error Correctin can be performed.
Add a crtc state for FEC. Currently, the state
is determined by platform, DP and DSC being
enabled. Moving forward we can use the state
to have error correction on other scenarios too
if needed.
v2:
- Control compression_enable with the fec_enable
parameter in crtc state and with intel_dp_supports_fec()
(Ville)
- intel_dp_can_fec()/intel_dp_supports_fec()(manasi)
v3: Check for FEC support along with setting crtc state.
v4: add checks to intel_dp_source_supports_dsc.(manasi)
- Move intel_dp_supports_fec() closer to
intel_dp_supports_dsc() (Anusha)
v5: Move fec check to intel_dp_supports_dsc(Ville)
v6: Remove warning. rebase.
v7: change crtc state to include DP sink and fec capability
of source.(Manasi)
v8: Set fec_enable in crtc in intel_dp_compute_config().
v9 (From Manasi):
* Combine the !edp and !fec_support check
* Derive dev_priv from intel_dp directly
v10 (From Manasi):
* Rebase
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.comk>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-14-manasi.d.navare@intel.com
A separate power well 2 (PG2) is required for VDSC on eDP transcoder
whereas all other transcoders use the power wells associated with the
transcoders for VDSC.
This patch adds a helper to obtain correct power domain depending on
transcoder being used and enables/disables the power wells during
VDSC enabling/disabling.
v4:
* Get VDSC power domain only if compression en is set
in crtc_state (Ville, Imre)
v3:
* Call it intel_dsc_power_domain, add to
intel_ddi_get_power_domains (Ville)
v2:
* Fix tabs, const crtc_state, fix comments (Ville)
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-13-manasi.d.navare@intel.com
1. Disable Left/right VDSC branch in DSS Ctrl reg
depending on the number of VDSC engines being used
2. Disable joiner in DSS Ctrl reg
v4:
* Remove encoder, make crtc_state const (Ville)
v3 (From Manasi):
* Add Disable PG2 for VDSC on eDP
v2 (From Manasi):
* Use old_crtc_state to find dsc params
* Add a condition to disable only if
dsc state compression is enabled
* Use correct DSS CTL regs
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-12-manasi.d.navare@intel.com
Display Stream Splitter registers need to be programmed to enable
the joiner if two DSC engines are used and also to enable
the left and the right DSC engines. This happens as part of
the DSC enabling routine in the source in atomic commit.
v4:
* Remove redundant comment (Ville)
v3:
* Use cpu_transcoder instead of encoder->type (Ville)
v2:
* Rebase (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intelcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-11-manasi.d.navare@intel.com
DSC PPS secondary data packet infoframes are filled with
DSC picure parameter set metadata according to the DSC standard.
These infoframes are sent to the sink device and used during DSC
decoding.
v3:
* Rename to intel_dp_write_pps_sdp (Ville)
* Use const intel_crtc_state (Ville)
v2:
* Rebase ond drm-tip
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-10-manasi.d.navare@intel.com
Infoframes are used to send secondary data packets. This patch
adds support for DSC Picture parameter set secondary data packets
in the existing write_infoframe helpers.
v3:
* Unused variables cleanup (Ville)
v2:
* Rebase on drm-tip (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-9-manasi.d.navare@intel.com
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
On Icelake, a separate power well PG2 is created for
VDSC engine used for eDP/MIPI DSI. This patch adds a new
display power domain for Power well 2.
v3:
* Call it POWER_DOMAIN_TRANSCODER_EDP_VDSC (Ville)
* Move it around TRANSCODER power domain defs (Ville)
v2:
* Fix the power well mismatch CI error (Ville)
* Rename as VDSC_PIPE_A (Imre)
* Fix a whitespace (Anusha)
* Fix Comments (Imre)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-7-manasi.d.navare@intel.com
This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.
v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-6-manasi.d.navare@intel.com
This computation of RC params happens in the atomic commit phase
during compute_config() to validate if display stream compression
can be enabled for the requested mode.
v7 (From Manasi):
* Use DRM_DEBUG instead of DRM_ERROR (Ville)
* Use Error numberinstead of -1 (Ville)
v6 (From Manasi):
* Use 9 instead of 0x9 for consistency (Anusha)
v5 (From Manasi):
* Fix dim checkpatch warnings/checks
v4(From Gaurav):
* No change.Rebase on drm-tip
v3 (From Gaurav):
* Rebase on top of Manasi's latest series
* Return -ve value in case of failure scenarios (Manasi)
Fix review comments from Ville:
* Remove unnecessary comments
* Remove unnecessary paranthesis
* Add comments for few RC params calculations
v2 (From Manasi):
* Rebase Gaurav's patch from intel-gfx to gfx-internal
* Use struct drm_dsc_cfg instead of struct intel_dp
as a parameter
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-5-manasi.d.navare@intel.com
This patches does the following:
1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific
This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.
v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks
v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)
v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)
Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers
v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129193827.7914-1-manasi.d.navare@intel.com
If a eDP panel supports both PSR2 and VDSC, our HW cannot
support both at a time. Give priority to PSR2 if a requested
resolution can be supported without compression else enable
VDSC and keep PSR2 disabled.
v4:
Fix the unrealted stuff removed during rebase (Ville)
v3:
* Rebase
v2:
* Add warning for DSC and PSR2 enabled together (DK)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-3-manasi.d.navare@intel.com
DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.
v15:
* Rebase over drm-tip
v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)
v7:
* Fix indentation in compute_m_n (Manasi)
v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)
v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)
v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)
v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)
v2:
* Add if-else for eDP/DP (Gaurav)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128213621.21391-1-manasi.d.navare@intel.com
Basic DSC parameters and DSC configuration data needs to be computed
for each of the requested mode during atomic check. This is
required since for certain modes, valid DSC parameters and config
data might not be computed in which case compression cannot be
enabled for that mode.
For that reason we need to add these params and config structure
to the intel_crtc_state so that if valid this state information
can directly be used while enabling DSC in atomic commit.
v2:
* Rebase on drm-tip (Manasi)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-1-manasi.d.navare@intel.com
In the future framebuffer stride alignment requirements won't exactly
match the units in which skl+ plane stride is specified. So extract
the code for the skl+ stuff into a separate helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180925193714.25280-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's try to make sure the fb offset computations never hit
an integer overflow by making sure the entire fb stays
below 32bits. framebuffer_check() in the core already does
the same check, but as it doesn't know about tiling some things
can slip through. Repeat the check in the driver with tiling
taken into account.
v2: Use add_overflows() after massaging it to work for me (Chris)
v3: Call it add_overflow_t() to match min_t() & co. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023160201.9840-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On icl+ the plane state that gets passed to update_slave() is not
the plane state of the plane we're programming. With NV12 the
plane state would be coming from the master (UV) plane whereas
the plane we're programming is the slave (Y) plane. For that reason
we need to explicitly pass around the slave plane (or we'd have to
otherwise deduce it by checking whether we were called via
.update_plane() or .update_slave()).
In the case of icl_program_input_csc_coeff() it's actually OK to
assume that we are always the master plane because the input CSC
only exists on HDR planes which can never be a slave plane. But
for consistency let's pass in the plane explicitly anyway.
While at it drop the "_coeff" from the function name since it's
kinda redundant, and this makes the name a bit shorter :)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-14-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
A variable whose name is 'plane_id' is expected to be of the
enum plane_id type. In this case we have a raw int, which turns
out to refer to the plane of the framebuffer. Rename the variable
to 'color_plane' in line with the trend started earlier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-13-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
skl+ can go belly up if there are overlapping ddb allocations between
planes. If we could absolutely guarantee that we can perform the atomic
update within a single frame we shouldn't have to worry about this. But
we can't rely on that so let's steal the ddb overlap check trick from
skl_update_crtcs() and apply it to the plane updates. Since each step
of the sequence is free from ddb overlaps we don't have to worry about
a vblank sneaking up on us in the middle of the sequence. The partial
state that gets latched by the hardware will be safe. And unlike
skl_update_crtcs() we don't have to intoduce any extra vblank waits
on account of only having to worry about a single pipe.
v2: Fix typo in commit msg (Matt)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-12-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
Simplify the calling convention of the skl+ watermark functions
by not passing around dev_priv needlessly. The callees have
what they need to dig it out anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-10-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Make a cleaner split between the skl+ and icl+ ways of computing
watermarks. This way skl_build_pipe_wm() doesn't have to know any
of the gritty details of icl+ master/slave planes.
We can also simplify a bunch of the lower level code by pulling
the plane visibility checks a bit higher up.
v2: WARN_ON(!visible) for the icl+ master plane case (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165726.31122-1-ville.syrjala@linux.intel.com
We have to pass both level 0 watermark struct and the transition
watermark struct to skl_compute_transition_wm(). Make life less
confusing by just passing the entire plane watermark struct that
contains both aforementioned structures.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-8-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We memset(0) the entire watermark struct the start, so there's no
need to clear things later on.
v2: Rebase due to some stale w/a removal
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-7-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If the level 0 latency is 0 we can't do anything. Return an error
rather than success.
While this can't happen due to WaWmMemoryReadLatency, it can
happen if the user clears out the level 0 latency via debugfs.
v2: Clarify how how we can end here with zero level 0 latency (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We're going to need access to the new crtc state in ->disable_plane()
for SKL+ wm/ddb programming and pre-skl pipe gamma/csc control. Pass
the crtc state down.
We'll also try to make intel_crtc_disable_planes() do the right
thing as much as it's possible. The fact that we don't have a
separate crtc state for the disabled state when we're going to
re-enable the crtc later means we might end up poking at a few
extra planes in there. But that's harmless. I suppose one might
argue that we wouldn't have to care about proper ddb/wm/csc/gamma
if the pipe is going to permanently disable anyway, but the state
checker probably cares so we should try our best to make sure
everything is programmed correctly even in that case.
v2: Fix the commit message a bit (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-5-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Keep track which planes need updating during the commit. For now
we set the bit for any plane that was or will be visible (including
icl+ nv12 slave planes). In the future I'll have need to update
invisible planes as well, for skl plane ddbs and for pre-skl pipe
gamma/csc control (which lives in the primary plane control register).
v2: Pimp the commit message to mention icl+ nv12 slave planes (Matt)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127163742.30215-1-ville.syrjala@linux.intel.com
The plane color correction registers are single buffered. So
ideally we would write them at the start of vblank just after the
double buffered plane registers have been latched. Since we have
no convenient way to do that for now let's at least move the
single buffered register writes to happen after the double
buffered registers have been written.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Some observations about the plane registers:
- the control register will self-arm if the plane is not already
enabled, thus we want to write it as close to (or ideally after)
the surface register
- tileoff/linoff/offset/aux_offset are self-arming as well so we want
them close to the surface register as well
- color keying registers we maybe self arming before SKL. Not 100%
sure but we can try to keep them near to the surface register
as well
- chv pipe b csc register are double buffered but self arming so
moving them down a bit
- the rest should be mostly armed by the surface register so we can
safely write them first, and to just for some consistency let's try
to follow keep them in order based on the register offset
None of this will have any effect of course unless the vblank evasion
fails (which it still does sometimes). Another potential future benefit
might be pulling the non-self armings registers outside the vblank
evasion since they won't latch until the arming register has been
written. This would make the critical section a bit lighter and thus
less likely to exceed the deadline.
v2: Rebase due to input CSC
v3: Swap LINOFF/TILEOFF and KEYMSK/KEYMAX to actually follow
the last rule above (Matt)
Add a bit more rationale to the commit message (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Mark A0 as the one and only pre-production variant of Kabylake and
remove its couple of workarounds, consigning them to the annals of
history.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128135325.10641-1-chris@chris-wilson.co.uk
If the engine's seqno is already at our target seqno (most likely it
hasn't been used since the last reset), we can skip serialising the
engine and leave it as is.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126095610.20962-1-chris@chris-wilson.co.uk
Currently, we convert the error state into a string every time we read
from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to
window the string and only capture the portion that is being read, but
that means that we must always convert up to the window to find the
start. For a very large error state bordering on EXEC_OBJECT_CAPTURE
abuse, this is noticeable as it degrades to O(N^2)!
As we do not have a convenient hook for sysfs open(), and we would like
to keep the lazy conversion into a string, do the conversion of the
whole string on the first read and keep the string until the error state
is freed.
v2: Don't double advance simple_read_from_buffer
v3: Due to extreme pain of lack of vrealloc, use a scatterlist
v4: Keep the forward iterator loosely cached
v5: Stylistic improvements to reduce patch size
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Testcase: igt/gem_exec_capture/many*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123132325.26541-1-chris@chris-wilson.co.uk
We should not access hardware while computing config also we don't
support stereo 3D so this test was never true.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-6-jose.souza@intel.com
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
will still keep the error set even after the reset done in the
irq_preinstall and irq_uninstall hooks.
And enabling in this situation cause the screen to freeze in the
first time that PSR HW tries to activate so lets keep PSR disabled
to avoid any rendering problems.
v5: rebased: using edp_psr_shift()
v4: Moved handling from intel_psr_compute_config() to
intel_psr_init() to avoid hardware access during compute(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
squash
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-5-jose.souza@intel.com
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
When we detect a error and disable PSR, it is kept disabled until the
next modeset but as the sink already show signs that it do not
properly work with PSR lets disabled it for good to avoid any
additional flickering.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-3-jose.souza@intel.com
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
While trying to add a chamelium test for short HPD IRQs, I ran into
issues where a hotplug storm would be triggered, but the point at which
it would be reported by the kernel would be after igt actually finished
checking i915_hpd_storm_ctl's status. So, fix this by simply
synchronizing our IRQ work, dig_port_work, and hotplug_work before
printing out the HPD storm status in i915_hpd_storm_ctl_show().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
Replace the messy framebuffer format/modifier validation code
with a single call to drm_any_plane_has_format(). The code was
extremely annoying to maintain as you had to have a lot of platform
checks for different formats. The new code requires zero maintenance.
v2: Nuke the modifier checks as well since the core does that too now
v3: Call drm_any_plane_has_format() from the driver code
v4: Rebase
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-2-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
There is no need to rebuild i915_gpu_error.o when the version string
changes as the version is available in init_utsname()->release.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121095423.20760-1-hans.ml.holmberg@owltronix.com
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
-----BEGIN PGP SIGNATURE-----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=elpS
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 2:
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c0409e3-a85f-d2af-b4eb-baf1eb8bbae4@linux.intel.com
When showing the list of waiters, include the task's status so that we
can tell if they have been woken up and are waiting for the CPU, or if
they are still waiting to be woken.
v2: task_state_to_char()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121151653.24595-1-chris@chris-wilson.co.uk
If we need to force a full plane update before userspace/fbdev
have given us a proper plane state we should try to maintain the
current plane state as much as possible (apart from the parts
of the state we're trying to fix up with the plane update).
To that end add basic readout for the plane rotation and
maintain it during the initial fb takeover.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-2-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit f43348a3db)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If we force a plane update to fix up our half populated plane state
we'll also force on the pipe gamma for the plane (since we always
enable pipe gamma currently). If the BIOS hasn't programmed a sensible
LUT into the hardware this will cause the image to become corrupted.
Typical symptoms are a purple/yellow/etc. flash when the driver loads.
To avoid this let's program something sensible into the LUT when
we do the plane update. In the future I plan to add proper plane
gamma enable readout so this is just a temporary measure.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit fa6af5145b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If we need to force a full plane update before userspace/fbdev
have given us a proper plane state we should try to maintain the
current plane state as much as possible (apart from the parts
of the state we're trying to fix up with the plane update).
To that end add basic readout for the plane rotation and
maintain it during the initial fb takeover.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-2-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If we force a plane update to fix up our half populated plane state
we'll also force on the pipe gamma for the plane (since we always
enable pipe gamma currently). If the BIOS hasn't programmed a sensible
LUT into the hardware this will cause the image to become corrupted.
Typical symptoms are a purple/yellow/etc. flash when the driver loads.
To avoid this let's program something sensible into the LUT when
we do the plane update. In the future I plan to add proper plane
gamma enable readout so this is just a temporary measure.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
Add a comment to the pipe and transcoder enum definitions about our
assumption in the code about enum values for pipes and transcoders
with a 1:1 transcoder -> pipe mapping.
v2:
- Clarify more what are the assumptions about the enum values. (Ville)
v3: (Lucas)
- s/->/ -> / so it looks less like pointer dereferencing.
- Use pipe enums as initializers in the transcoder enum definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-3-imre.deak@intel.com
Depending on the transcoder enum values to translate from transcoder
to EDP PSR flags can easily break if we add a new transcoder. So remove
the dependency by using an explicit mapping.
While at it also add a WARN for unexpected trancoders.
v2:
- Simplify things by defining flag shift values instead of indices.
- s/trans/cpu_transcoder/ (Ville)
v3:
- Define flags to look like separate bits instead of the values of
the same bitfield. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-2-imre.deak@intel.com
Depending on the transcoder enum values to translate from transcoder
to pipe/transcoder register addresses can easily break if we add a new
transcoder. So remove the dependency by using named initializers.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-1-imre.deak@intel.com
Found by smatch:
drivers/gpu/drm/i915/gvt/gtt.c:2452 intel_vgpu_destroy_ggtt_mm() error: dereferencing freed memory 'pos'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
(cherry picked from commit 7fa28e1469)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Like it was done in commit 9e180d9991 ("drm/i915: Downgrade unknown
firmware warnings") for huc and guc: downgrade CSR firmware warnings. If
we have released no firmware yet for a platform, stop scaring the
consumer and merely note its expected absence.
By simply removing the warning and early return we hit the condition
with the appropriate message.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-2-lucas.demarchi@intel.com
Before commit d8a5b7d79f ("drm/i915/csr: keep max firmware size together
with firmare name and version") it was possible to load the firmware for
testing purposes via parameter. Let's use the size of the last known
platform to recover that behavior.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-1-lucas.demarchi@intel.com
Clean up fixed point temp variable initialization, use the more
conventional tmp name for temp variables, add empty lines before
return. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-5-jani.nikula@intel.com
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad622 ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
(cherry picked from commit fb6f0b64e4)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad622 ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
(cherry picked from commit 03981c6ebe)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Hide the enable_gvt modparam in the default scenario where
support has not been compiled in.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116144447.7836-1-joonas.lahtinen@linux.intel.com
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
If we have released no firmware yet for a platform, stop scaring the
consumer and merely note its expected absence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Petri Latvala <petri.latvala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009111259.20807-1-chris@chris-wilson.co.uk
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
Bspec 21257 says "DDIA PHY is the comp master, so it must
not be un-initialized if other combo PHYs are in use". Here
we are shutting down all phys, so it's not strictly required.
However let's be consistent on deinitializing things in the
reversed order we initialized them.
v2: simplify protection for enum port being unsigned in future
v3: spell out reverse rather than rev
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114011509.3667-2-lucas.demarchi@intel.com
These are the only places that assume ports A and B are the ones with
combo phy. Let's use intel_port_is_combophy() there to make sure
it checks for combo phy ports the same way everywhere.
v2: define for_each_combo_port() helper to check the ports
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114011509.3667-1-lucas.demarchi@intel.com
Vandita Kulkarni