This allows us to correctly add a VLAN even if it matches our default
VID. However, we don't want to remove the VID rules once that VLAN is
deleted. Correctly remove the stack layers information of the VLAN, but
then return to forwarding that VID as untagged frames. If we deleted the
VID rules here, we would begin dropping traffic due to VLAN membership
violations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reset delays used for stmmac are in the order of 10ms to 1 second,
which is far too long for udelay usage, so switch to using msleep.
Practically this fixes the PHY not being reliably detected in some cases
as udelay wouldn't actually delay for long enough to let the phy
reliably be reset.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression introduced by the commit a84e328941
("net: mvneta: fix refilling for Rx DMA buffers"). Due to this commit
the newly allocated Rx buffers are DMA-unmapped in place of those passed
to the networking stack. Obviously, this causes data corruptions.
This patch fixes the issue by ensuring that the right Rx buffers are
DMA-unmapped.
Reported-by: Oren Laskin <oren@igneous.io>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: a84e328941 ("net: mvneta: fix refilling for Rx DMA buffers")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Oren Laskin <oren@igneous.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code around the allocation and loops are a bit obfuscated.
Neaten it by using:
o kcalloc with decimal count and sizeof(u32)
o Decimal loop indexing and i++ not i += 4
o A promiscuous block using a similar style
to the multicast block
o Remove unnecessary variables
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the second 10GbE port on APM X-Gene SoC
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory patch for moving irq_data struct members. Search
and replace was done with coccinelle
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
commit c48f350ff5 "bnx2x: Add MFW dump support" added the
bnx2x_update_mfw_dump() function that reads the current time and stores
it in a 32-bit field that gets passed into a buffer in a fixed format.
This is potentially broken when the epoch overflows in 2038, and
otherwise overflows in 2106. As we're trying to avoid uses of
struct timeval for this reason, I noticed the addition of this
function, and tried to rewrite it in a way that is more explicit
about the overflow and that will keep working once we deprecate
struct timeval.
I assume that it is not possible to change the ABI any more, otherwise
we should try to use a 64-bit field for the seconds right away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix out-of-bounds array access in netfilter ipset, from Jozsef
Kadlecsik.
2) Use correct free operation on netfilter conntrack templates, from
Daniel Borkmann.
3) Fix route leak in SCTP, from Marcelo Ricardo Leitner.
4) Fix sizeof(pointer) in mac80211, from Thierry Reding.
5) Fix cache pointer comparison in ip6mr leading to missed unlock of
mrt_lock. From Richard Laing.
6) rds_conn_lookup() needs to consider network namespace in key
comparison, from Sowmini Varadhan.
7) Fix deadlock in TIPC code wrt broadcast link wakeups, from Kolmakov
Dmitriy.
8) Fix fd leaks in bpf syscall, from Daniel Borkmann.
9) Fix error recovery when installing ipv6 multipath routes, we would
delete the old route before we would know if we could fully commit
to the new set of nexthops. Fix from Roopa Prabhu.
10) Fix run-time suspend problems in r8152, from Hayes Wang.
11) In fec, don't program the MAC address into the chip when the clocks
are gated off. From Fugang Duan.
12) Fix poll behavior for netlink sockets when using rx ring mmap, from
Daniel Borkmann.
13) Don't allocate memory with GFP_KERNEL from get_stats64 in r8169
driver, from Corinna Vinschen.
14) In TCP Cubic congestion control, handle idle periods better where we
are application limited, in order to keep cwnd from growing out of
control. From Eric Dumzet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
tcp_cubic: better follow cubic curve after idle period
tcp: generate CA_EVENT_TX_START on data frames
xen-netfront: respect user provided max_queues
xen-netback: respect user provided max_queues
r8169: Fix sleeping function called during get_stats64, v2
ether: add IEEE 1722 ethertype - TSN
netlink, mmap: fix edge-case leakages in nf queue zero-copy
netlink, mmap: don't walk rx ring on poll if receive queue non-empty
cxgb4: changes for new firmware 1.14.4.0
net: fec: add netif status check before set mac address
r8152: fix the runtime suspend issues
r8152: split DRIVER_VERSION
ipv6: fix ifnullfree.cocci warnings
add microchip LAN88xx phy driver
stmmac: fix check for phydev being open
net: qlcnic: delete redundant memsets
net: mv643xx_eth: use kzalloc
net: jme: use kzalloc() instead of kmalloc+memset
net: cavium: liquidio: use kzalloc in setup_glist()
net: ipv6: use common fib_default_rule_pref
...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104031
Fixes: 6e85d5ad36
Based on the discussion starting at
http://www.spinics.net/lists/netdev/msg342193.html
Tested locally on RTL8168evl/8111evl with various concurrent processes
accessing /proc/net/dev while changing the link state as well as
removing/reloading the r8169 module.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporate fw_ldst_cmd structure change for new firmware and also
update version string for the same
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist one issue by below case that case system hang:
ifconfig eth0 down
ifconfig eth0 hw ether 00:10:19:19:81:19
After eth0 down, all fec clocks are gated off. In the .fec_set_mac_address()
function, it will set new MAC address to registers, which causes system hang.
So it needs to add netif status check to avoid registers access when clocks are
gated off. Until eth0 up the new MAC address are wrote into related registers.
V2:
As Lucas Stach's suggestion, add a comment in the code to explain why it needed.
CC: Lucas Stach <l.stach@pengutronix.de>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current check of phydev with IS_ERR(phydev) may make not much sense
because of_phy_connect() returns NULL on failure instead of error value.
Still for checking result of phy_connect() IS_ERR() makes perfect sense.
So let's use combined check IS_ERR_OR_NULL() that covers both cases.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The double memset is a little ugly; using kzalloc avoids it altogether.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using kzalloc saves a tiny bit on .text.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We save a little .text and get rid of the sizeof(...) style
inconsistency.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For !CONFIG_OF of_get_property() is defined to always return NULL. Thus
there's no need to protect the call to of_get_property() with #ifdef
CONFIG_OF.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The write-combining configuration register SGE_STAT_CFG_A needs to
be configured after FW initializes the adapter, else FW will reset
the configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0aac3f56d4 ("cxgb4: Add comment for calculate tx flits
and sge length code") introduced a regression where tx flit calculation
is going wrong, which can lead to data corruption, hang, stall and
write-combining failure. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_off() prior to register_netdev(), otherwise
userspace can see incorrect link state.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function ‘init_one’:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4579:8: warning: ‘chip’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip |= CHELSIO_CHIP_CODE(CHELSIO_T4, pl_rev);
^
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4571:11: note: ‘chip’ was declared here
int ver, chip;
^
Fixes: d86bd29e0b ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I register")
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fec MDIO write method succeeds its return value comes from
call to pm_runtime_get_sync().
But pm_runtime_get_sync() can also return 1.
In case of Micrel KSZ9031 PHY this value will then
be returned along the call chain of phy_write() ->
ksz9031_extended_write() -> ksz9031_center_flp_timing() ->
ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() ->
phy_connect_direct().
Then phy_connect() will cast it into a pointer using ERR_PTR(),
which then fec_enet_mii_probe() will try to dereference
resulting in an oops.
Fix it by normalizing return value of pm_runtime_get_sync()
to be zero if positive in MDIO write method.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The be_cmd_rx_filter() routine sends a non-embedded cmd to the FW and used
a pre-allocated dma memory to hold the cmd payload. This worked fine when
this cmd was synchronous. This cmd was changed to asynchronous mode by the
commit 8af65c2f4("make the RX_FILTER command asynchronous"). So now when
there are two quick invocations of this cmd, the 2nd request may end up
overwriting the first request, causing FW cmd corruption.
This patch reverts the offending commit and hence fixes the regression.
Fixes: 8af65c2f4("be2net: make the RX_FILTER command asynchronous")
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
tse_poll() calls __napi_complete() with irq enabled. This leads napi
poll_list corruption and may stop all napi drivers working.
Use napi_complete() instead of __napi_complete().
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch just to re-submit the patch "db3421c114cfa6326" because the
patch "4d494cdc92b3b9a0" remove the change.
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:
drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'
Add the missing argument.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-01
This series contains updates to i40e, ixgbe and ixgbevf.
Anjali fixes a bug in i40e where the port is not receiving multicast or VLAN
tagged packets in promiscuous mode. Which can occur when a software bridge
is created on top of the device.
Don adds support in ixgbe that indicates the presence of management firmware.
Added support for entering low power link up state on devices that support
it when the device is closing or suspending. Updated the driver to report
unknown bus speed and width since IOSF does not report a PCIe bus speed or
width for X550 devices. Also added the new bus type for integrated I/O
interface (IOSF). Cleaned up of redundant code in ixgbe.
Mark adds support for UDP-encapsulation transmit checksum and for VXLAN
receive offloads. Introduces a helper function to do the register access
and processing to avoid needless PHY access on copper PHYs. Added support
for reporting 2.5G link speed. Fixed warnings resulting from redundant
initializations of the get_bus_info field.
Maninder Singh updates the ixgbe driver to use kzalloc instead of kcalloc
for allocation of one thing.
Tom Barbette adds support for ethtool to change the rxfh indirection table
and/or key using ethtool interface.
Emil resolves an issue where users were not able to dynamically set number
of queues for 82598 via ethtool -L.
Alex Williamson removes bimodal SR-IOV disabling behavior since it is
confusing to users and results in a state where the PF is broken for other
uses unless the user sets sriov_numvfs to zero prior to unbinding the
device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the redundant lan_id in the phy struct and uses
the bus version. Both variables exist and intend to represent the
STATUS register LAN_ID field. However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use kzalloc rather than kcalloc(1..
The semantic patch that makes this change is as follows:
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices. So remove the unused types from the
ixgbe_bus_type. Thanks to Alex Duyck for suggesting this.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime. So we will
set the value in get_invariants.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.
This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.
We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.
In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.
Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flags argument will allow control of the dissection process (for
instance whether to parse beyond L3).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf4 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull NOHZ updates from Ingo Molnar:
"The main changes, mostly written by Frederic Weisbecker, include:
- Fix some jiffies based cputime assumptions. (No real harm because
the concerned code isn't used by full dynticks.)
- Simplify jiffies <-> usecs conversions. Remove dead code.
- Remove early hacks on nohz full code that avoided messing up idle
nohz internals. Now nohz integrates well full and idle and such
hack have become needless.
- Restart nohz full tick from irq exit. (A simplification and a
preparation for future optimization on scheduler kick to nohz
full)
- Code cleanups.
- Tile driver isolation enhancement on top of nohz. (Chris Metcalf)"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Remove useless argument on tick_nohz_task_switch()
nohz: Move tick_nohz_restart_sched_tick() above its users
nohz: Restart nohz full tick from irq exit
nohz: Remove idle task special case
nohz: Prevent tilegx network driver interrupts
alpha: Fix jiffies based cputime assumption
apm32: Fix cputime == jiffies assumption
jiffies: Remove HZ > USEC_PER_SEC special case
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting VF's corresponding BGX LMAC in internal
loopback mode. This mode can be used for verifying basic HW
functionality such as packet I/O, RX checksum validation,
CQ/RBDR interrupts, stats e.t.c. Useful when DUT has no external
network connectivity.
'loopback' mode can be enabled or disabled via ethtool.
Note: This feature is not supported when no of VFs enabled are
morethan no of physical interfaces i.e active BGX LMACs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for handling multiple qsets assigned to a
single VF. There by increasing no of queues from earlier 8 to max
no of CPUs in the system i.e 48 queues on a single node and 96 on
dual node system. User doesn't have option to assign which Qsets/VFs
to be merged. Upon request from VF, PF assigns next free Qsets as
secondary qsets. To maintain current behavior no of queues is kept
to 8 by default which can be increased via ethtool.
If user wants to unbind NICVF driver from a secondary Qset then it
should be done after tearing down primary VF's interface.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework interrupt handler to avoid checking IRQ affinity of
CQ interrupts. Now separate handlers are registered for each IRQ
including RBDR. Register interrupt handlers for only those
which are being used. Add nicvf_dump_intr_status() and use it
in irq handlers.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures HW to strip 802.1Q header if found in a
receiving packet. The stripped VLAN ID and TCI information is
passed on to software via CQE_RX. Also sets netdev's 'vlan_features'
so that other HW offload features can be used for tagged packets.
This offload feature can be enabled or disabled via ethtool.
Network stack normally ignores RPS for 802.1Q packets and hence low
throughput. With this offload enabled throughput for tagged packets
will be almost same as normal packets.
Note: This patch doesn't enable HW VLAN insertion for transmit packets.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for receive hashing HW offload by using RSS_ALG
and RSS_TAG fields of CQE_RX descriptor. Also removed dependency
on minimum receive queue count to configure RSS so that hash is
always generated.
This hash is used by RPS logic to distribute flows across multiple
CPUs. Offload can be disabled via ethtool.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the nicvf_send_msg_to_pf() function in the mailbox code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool support to dump receive packet error statistics reported
in CQE. Also made some small fixes
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 network driver was registered in the context of the 'add'
function of the core driver (called when HW should be registered).
This makes the netdev event NETDEV_REGISTER to be sent in a context
where the answer to get_protocol_dev() callback returns NULL. This may
be confusing to listeners of netdev events.
This patch is a preparation to the patch that implements the
get_netdev() callback in the IB/mlx4 driver.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The interrupt handler may not be available when smsc911x probes if the
interrupt handler is a GPIO controller for example. Let's fix that
by adding handling for -EPROBE_DEFER.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver overrides the error returned by platform_get_irq() with -ENODEV
which e.g. precludes the deferred probing from working. Propagate the real
error code to the driver core instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver overrides the error returned by platform_get_irq() with -ENODEV
which e.g. precludes the deferred probing from working. Propagate the real
error code to the driver core instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously, the driver would refuse to load if it couldn't secure
enough VIs from the MC to fulfill its RSS requirements.
This was causing probe to fail on later functions in
configurations where we'd run out of VIs, such as having many
VFs.
This change allows the driver to load with fewer VIs, down to a
minimum of 2. A warning will be printed saying that RSS
requirements were not met, possibly affecting performance.
efx->max_tx_channels needs to be set to avoid going down the
failure path in efx_probe_nic() immediately in the loop after the
probe() NIC-type function.
Also, Set rc=ENOSPC when bombing out of efx_probe_nic due to lack
of VIs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit. Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed. To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Some straggler bug fixes here:
1) Netlink_sendmsg() doesn't check iterator type properly in mmap
case, from Ken-ichirou MATSUZAWA.
2) Don't sleep in atomic context in bcmgenet driver, from Florian
Fainelli.
3) The pfkey_broadcast() code patch can't actually ever use anything
other than GFP_ATOMIC. And the cases that right now pass
GFP_KERNEL or similar will currently trigger an RCU splat. Just
use GFP_ATOMIC unconditionally. From David Ahern.
4) Fix FD bit timings handling in pcan_usb driver, from Marc
Kleine-Budde.
5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.
6) Traversal into drivers/net/ethernet/renesas should be triggered by
CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
option. From Kazuya Mizuguchi.
7) Fix regression in handling of igmp_join errors in vxlan, from
Marcelo Ricardo Leitner.
8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
mutex when programming the registers. From Russell King.
9) Fix non-forced handling in u32_destroy(), from WANG Cong.
10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
usbnet_stop(), from Eugene Shatokhin.
11) In sfc driver, don't fetch statistics firmware isn't capable of,
from Bert Kenward.
12) Verify ASCONF address parameter location in SCTP, from Xin Long"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
sctp: asconf's process should verify address parameter is in the beginning
sfc: only use vadaptor stats if firmware is capable
net: phy: fixed: propagate fixed link values to struct
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
drivers: net: xgene: fix: Oops in linkwatch_fire_event
cls_u32: complete the check for non-forced case in u32_destroy()
net: fec: use reinit_completion() in mdio accessor functions
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
vxlan: re-ignore EADDRINUSE from igmp_join
net: compile renesas directory if NET_VENDOR_RENESAS is configured
ip6_gre: release cached dst on tunnel removal
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
net: Fix RCU splat in af_key
net: bcmgenet: fix uncleaned dma flags
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
netlink: mmap: fix tx type check
The uninitialized value name in mlx4_en_activate_cq was used in order
to print an error message. Fixing it by replacing it with cq->vector.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently manage IRQs in pool_bm which is a bit field
of MAX_MSIX bits. Thus, allocating more than MAX_MSIX
interrupts can't be managed in pool_bm.
Fixing this by capping number of requested MSIXs to
MAX_MSIX.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW-SW contract requires mailboxes passed to the firmware to be 4KB
aligned. Previously, these mailboxes were mapped using streaming DMA
routines, which do not guarantee the bus addresses to be 4KB aligned.
Under certain conditions this constraint was indeed violated and errors
were observed.
By using consistent DMA mapping routines together with a mailbox size of
4KB we are guaranteed not to violate the constraint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmit fails, it is an error, not a warning.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now information about changed upper is passed along, benefit from
that and use this info directly.
This also fixes possible issues that could happen when non-master device
is added (current code does not distinguish between master and non-master
upper device).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at rtnl kind string is kind of ugly. So use new helpers to do
this in nicer way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62ee783bf1 ("smsc911x: Fix crash seen if neither ACPI nor OF is
configured or used") introduces an error check for the return value from
device_get_phy_mode() and bails out if there is an error. Unfortunately,
there are configurations where no phy is configured. Those configurations
now fail.
To fix the problem, accept error returns from device_get_phy_mode(),
and use the return value from device_property_read_u32() to determine
if there is a suitable firmware interface to read the configuration.
Fixes: 62ee783bf1 ("smsc911x: Fix crash seen if neither ACPI nor OF is configured or used")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-26
This series contains updates to i40e and i40evf only.
Anjali provides a fix for i40e where the part is not receiving multicast
or VLAN tagged packets when in promiscuous mode. This can occur when a
software bridge is created on top of the device. Fixed the legacy and MSI
interrupt mode in the driver, which was non-existent before since we
were assuming MSIX was the only mode that the driver ran in. Fixed the
i40evf driver, where the wrong defines were getting used in the VF
driver.
Mitch fixes a sparse warning about comparing __le16 to u16 so use
le16_to_cpu() to resolve the warning. Also fixed a dyslexic spelling
of invalid.
Shannon adds port.crc_errors to receive CRC error counter, since it
is a receive counter.
Catherine provides a fix to move the stopping of the service task and
flow director to i40e_shutdown() instead of i40e_suspend().
Greg fixes the ethtool offline diagnostic with netqueues, which just need
to be treated the same as virtual functions when someone wants to run the
ethtool offline diagnostic test. Also fixed up code comments for the
i40e ethtool diagnostic test function. Cleans up redundant and unneeded
messages, since the kernel notifies all VXLAN capable registered drivers,
so no need to log this.
Neerav adds the ability to update statistics per VEB per traffic class
and dump it via ethtool.
Jingjing adds support for virtual channel offload to support receive
polling mode in the VF driver.
v2: dropped patch which added helper functions into a header, feedback from
David Miller was to make the functions constant to reduce the driver
footprint, so remove the patch while Anjali works on making the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No pr_dbg method exists.
While this code is #if 0'd, it'd be nicer to
use the generic hex_dump, so use it instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rearranged descriptor writes
- Moved increment command write to xgene_enet_setup_tx_desc
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom buses may have more than 1 Ethernet device. This is used e.g.
to have few interfaces connected to different switch ports. So far we
saw chipsets with only 2 devices (e.g. BCM4706) but recent ones have
up to 3 (e.g. Netgear R8000 uses 3rd interface for most of switch
traffic, lower interfaces are for some kind of offloading).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the stats handling code differs based on SR-IOV support,
and SRIOV support is only available if full-featured firmware is
used.
Do not use vadaptor stats if firmware mode is not set to
full-featured.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel notifies all VXLAN capable registered drivers, i.e. any
driver that implements ndo_add_vxlan_port(), of the addition of a
port so that the driver can track which ports are in use. There's
no need to log this - it just fills the system log with useless and
irksome noise.
Also, when failing to init SR-IOV interfaces the driver was printing the
same message twice. Just remove the inner printk and let the outer message
catch enable as well as the other failures.
Change-ID: Id5ecb1d425c2a357ee2bc1635dab24553831dade
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were quite a few issues when the wrong defines were getting used
in the VF driver. This patch fixes the code where PF driver registers
were getting used for VF driver, and also removes the registers that are
not being used from the VF register file.
Change-ID: If116a9730112950d006eb8ec763998fc914cc839
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use CTLN1 instead of CTLN for the VF relative register space.
Change-ID: Iefba63faf0307af55fec8dbb64f26059f7d91318
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Turns out that 'inavlid' is an inavlid spelling for 'invalid'.
Change-ID: Ie1fe2d0f8d1ba75ab880594875ec2e4152a76f61
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing comment is incorrect. Add new comment to point out that the
PF reset does not affect link but if the reset is changed to a different
type that does affect link then the link test would need to be moved to
before the reset.
Change-ID: I28d786f46e9465860babdee61c1dba51016464df
Reported-by: Jeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Treat netqueues the same way we do virtual functions when someone wants to
run the ethtool offline diagnostic test.
Change-ID: Id48d2b933f1fd0db7be06305a93c6ebe3dc821f5
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the driver flow to take into account legacy interrupts.
Over time we added code that assumes MSIX is the only mode that the
driver runs in. It also enables a legacy workaround to trigger SWINT
when the TX ring has non-cache aligned descriptors pending and interrupts
are disabled.
We work with a single vector in MSI mode too, so apply the same
restrictions as Legacy.
Change-ID: I826ddff1f9bd45d2dbe11f56a3ddcef0dbf42563
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should be stopping the service task and flow director on
shutdown not on suspension.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The port.crc_errors is really an RX counter, so let's mark it as such.
Change-ID: I179afd3f8a95d45229bb4163a6aeb01f0d2d250b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse cries when we compare an __le16 to a u16, almost like it cares
about architectures other than x86. Weird. Use the le16_to_cpu macro to
make it stop crying.
Change-ID: Id068f4d7868a2d3df234a791a76d15938f37db35
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
posted_index is RO in firmware. We need not do ioread everytime to get
posted index. Store posted index locally.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the renesas ethernet driver directory is compiled if SH_ETH is
configured rather than NET_VENDOR_RENESAS. Although incorrect that was
quite harmless as until recently as SH_ETH configured the only driver in
the renesas directory. However, as of c156633f13 ("Renesas Ethernet AVB
driver proper") the renesas directory includes another driver, configured
by RAVB, and it makes little sense for it to have a hidden dependency on
SH_ETH.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[horms: rewrote changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8169 driver collects statistical information returned by
@get_stats64 by counting them in the driver itself, even though many
(but not all) of the values are already collected by tally counters
(TCs) in the NIC. Some of these TC values are not returned by
@get_stats64. Especially the received multicast packages are missing
from /proc/net/dev.
Rectify this by fetching the TCs and returning them from
rtl8169_get_stats64.
The counters collected in the driver obviously disappear as soon as the
driver is unloaded so after a driver is loaded the counters always start
at 0. The TCs on the other hand are only reset by a power cycle. Without
further considerations the values collected by the driver would not match
up against the TC values.
This patch introduces a new function rtl8169_reset_counters which
resets the TCs. Also, since rtl8169_reset_counters shares most of
its code with rtl8169_update_counters, refactor the shared code into
two new functions rtl8169_map_counters and rtl8169_unmap_counters.
Unfortunately chip versions prior to RTL_GIGA_MAC_VER_19 don't allow
to reset the TCs programatically. Therefore introduce an addition to
the rtl8169_private struct and a function rtl8169_init_counter_offsets
to store the TCs at first rtl_open. Use these values as offsets in
rtl8169_get_stats64. Propagate a failure to reset *and* update the
counters up to rtl_open and emit a warning message, if so.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claim the emac sram ourselves, rather then relying on the bootloader
having mapped the sram to the emac controller during boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid multiply/division operations on the data path,
we hold a {channel, tc}==>txq mapping table.
We held this mapping table inside the channel object that is
being destroyed upon some configuration operations (e.g MTU change).
So in case ndo_select_queue occurs during such a configuration operation,
it may access a NULL channel pointer, resulting in kernel panic.
To fix this issue we moved the {channel, tc}==>txq mapping table
outside the channel object so that it will be available also
during such configuration operations.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BQL patch is based on work done by Tino Reichardt.
Tested on 0000:05:00.0: 3Com PCI 3c905C Tornado at ffffc90000e6e000 by running
Flent several times.
Signed-off-by: Loganaden Velvindron <logan@elandsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the dma flags of multiq ring buffer int the interface stop
process. This patch fixes that the genet is not running while the
interface is re-enabled.
$ ifup eth0 - running after booting
$ ifdown eth0
$ ifup eth0 - not running and occur tx_timeout
The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag
only. If the genet has multiq, the dma register is not cleaned. and
bcmgenet_init_dma() is not done correctly. in case
GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running
bcmgenet_dma_disable().
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_timeout() executes in atomic context, yet we will invoke
napi_disable() which does sleep. Looking back at the changes, disabling
TX napi and re-enabling it is completely useless, since we reclaim all
TX buffers and re-enable interrupts, and wake up the TX queues.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We define buf_int_enable in the minimal namespace it is used.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for when TX done interrupt is in
"level mode".
For example it is true for some simulators of this device.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set controller to drop control frames and not trying
to pass them on. This is only needed for debug reasons.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set tx_skb pointer before send frame.
If we receive interrupt before we set pointer we will try
to free SKB with wrong pointer.
Now we are sure that SKB pointer will never be NULL during
handling TX done and check is removed.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interrupt is received we read directly from control
register for RX/TX instead of reading cause register
since this register fails to indicate TX done when
TX interrupt is "edge mode".
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
err_out_vnic_unregister is used regardless of whether
SRIOV is enabled or not.
Reported-by: Jesse Brandeburg <jesse.brangeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the xgene_get_mac_address to device_get_mac_address(), and
xgene_get_phy_mode() to device_get_phy_mode().
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev==NULL check in smsc911x_probe_config is useless
and isn't providing any additional protection. If a fwnode
doesn't exist then an appropriate error should be returned
by device_get_phy_mode() covering the original case
of a missing of/fwnode.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34fa14cc0 ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-18
This series contains updates to igb, e100, e1000e and ixgbe.
Shota Suzuki provides a fix for a possible overflow in
igb_set_interrupt_capability() which leads to an oops. When changing the
number of queues by "ethtool -L", set IGB_FLAG_QUEUE_PAIRS in the same
manner as when initializing the igb driver.
Vasily Averin provides a fix for a missing rtnl_unlock() for when we
error out due to not being able to allocate memory for our queues.
Stefan Assman provides a couple of fixes for igb/igbvf. First changes
the igb driver in probe to simply call igb_enable_sriov() instead of
igb_sriov_reinit() since we are starting from scratch. Then in igbvf,
fix the driver where it does not clear the buffer_info->dma in all
cases after calling dma_unmap_single(), which was found by changing the
MTU twice.
Richard Cochran implements the periodic output function using the
programmable clock outputs available in i210 when possible, falling
back to the target time for longer periods.
Todd adds support for the Marvell PHY 1512 which is required for i354
devices. Then updates igb to make sure SR-IOV init uses the correct
number of queues, since recent changes could result in the PF holding
onto all of the queues.
Alex Williamson provides a fix in the case where a guest OS does not
support hot-unplug, so disable SR-IOV prior to unregister_netdev() to
avoid the problem.
Jia-Ju Bai provides several patches, first knocks some collecting dust
off an old e100 driver to add a check to avoid a null pointer
dereference. Then cleans up a possible resource leak by releasing the
skb buffer allocated when the e100_xmit_prepare() runs into an issue
in the DMA mapping. In igb, add a missing rtnl_unlock() for when we
error out due to igb_sriov_reinit() in the igb_init_interrupt_scheme().
Provides a e1000e fix, based on suggestions from Alex Duyck to move
head/tail register writing to e1000_configure_tx/rx() to avoid a
possible null pointer dereference (similar to igb driver). Lastly,
fix a possible memory leak in igb_probe(), where the memory shadow_vfta
allocated by kcalloc in igb_sw_init() is not freed.
Mark simplifies port-specific macros for ixgbe by eliminating explicit
comparisons with 0 and enclose formal parameters in parens to eliminate
the risk of an operator precedence issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't use kstrtoul() with an int or it causes memory corruption.
Also j should be unsigned or we have underflow bugs.
I considered changing "j" to unsigned long but everything fits in a u32.
Fixes: 8e3d04fd7d ('cxgb4: Add MPS tracing support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/built-in.o: In function `.vnic_wq_devcmd2_alloc':
(.text+0x49fe40): multiple definition of `.vnic_wq_devcmd2_alloc'
drivers/scsi/built-in.o:(.text+0xb4318): first defined here
drivers/net/built-in.o:(.opd+0x2af00): multiple definition of `vnic_wq_devcmd2_alloc'
drivers/scsi/built-in.o:(.opd+0xad70): first defined here
drivers/net/built-in.o: In function `.vnic_wq_init_start':
(.text+0x49f9c0): multiple definition of `.vnic_wq_init_start'
drivers/scsi/built-in.o:(.text+0xb3b58): first defined here
drivers/net/built-in.o:(.opd+0x2ae88): multiple definition of `vnic_wq_init_start'
drivers/scsi/built-in.o:(.opd+0xace0): first defined here
Rename these to 'enic_*' to avoid the conflict with the functiosn of
the same name in the snic scsi driver.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW submission added some vxlan offload capabilities to our device.
This patch adds the ability to connect to the vxlan NDOs and configure
the UDP port associated with it in the HW.
The device would now be capable of performing RSS according to the
inner headers of the vxlan packets.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify port-specific macros by eliminating explicit comparison
with 0. More importantly, enclose formal parameter in parens to
eliminate the risk of an operator precedence surprise.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to igb_probe_vfs() could lead to the PF holding onto all
of the queues. Reorder igb_probe_vfs() to be before
gb_init_queue_configuration() and add some more error checking.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In error handling code of igb_probe, the memory adapter->shadow_vfta
allocated by kcalloc in igb_sw_init is not freed. So when register_netdev
or igb_init_i2c is failed, a memory leak will occur.
This patch adds kfree to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_setup_rx_resources is failed in e1000_open,
e1000e_free_tx_resources in "err_setup_rx" segment is executed.
"writel(0, tx_ring->head)" statement in e1000_clean_tx_ring
in e1000e_free_tx_resources will cause a null poonter dereference(crash),
because "tx_ring->head" is only assigned in e1000_configure_tx
in e1000_configure, but it is after e1000e_setup_rx_resources.
This patch moves head/tail register writing to e1000_configure_tx/rx,
which can fix this problem. It is inspired by igb_configure_tx_ring
in the igb driver.
Specially, thank Alexander Duyck for his valuable suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When igb_init_interrupt_scheme in igb_sriov_reinit is failed, the lock
acquired by rtnl_lock() is not released, which causes a deadlock.
This patch adds rtnl_unlock() in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When pci_dma_mapping_error in e100_xmit_prepare is failed, the skb buffer
allocated by netdev_alloc_skb_ip_align in e100_rx_alloc_skb is not
released, which causes a possible resource leak.
This patch adds error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks the check of nic->cbs_pool after pci_pool_create
in e100_probe. When this function is failed, a null pointer dereference
occurs when pci_pool_alloc uses nic->cbs_pool in e100_alloc_cbs.
This patch adds a check and related error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for Marvell PHY 1512 (required for I354).
Submitted by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In addition to interrupt driven target time output events, the i210
also has two programmable clock outputs. These clocks support periods
between 16 nanoseconds and 140 milliseconds. This patch implements
the periodic output function using the clock outputs when possible,
falling back to the target time for longer periods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d2 ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b783579 ("igb: Add ethtool support to configure number of channels")
CC: stable <stable@vger.kernel.org>
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
>> drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: sparse: incorrect type in assignment (different address spaces)
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: expected void *res
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: got void [noderef] <asn:2>*
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>> drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: sparse: incorrect type in argument 1 (different base types)
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: expected restricted __sum16 [usertype] n
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: got restricted __be16 [usertype] check_sum
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only for packets with first ethertype set to IPv4/6 for now.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Change the maximum LRO session size from 16KB to 64KB
- Reduce the LRO session timeout from 512us to 32us in
order to reduce the TCP latency of non-LRO'ed flows.
- Fix skb_shinfo(skb)->gso_size and set skb_shinfo(skb)->gso_type.
- Fix a bug accessing un-initialized mdev pointer.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We un-intentionally limited the minimum rings size too much.
TX minimum ring size reduced from 128 to 64.
RX minimum ring size reduced from 128 to 2.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirection table size was defined by a variable that
was actually assigned a constant value.
Since we do not have any forseen intension to make it configurable
we simply made it a constant.
We also limit the number of channels such that the RSS indirection
table could always populate all RX rings.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to generate a unique key per TIR.
Generating a single key per netdev and copying it to all
its TIRs.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devcmd is an interface for driver to communicate with fw/adaptor. It
involves writing data to hardware registers and waiting for the result.
This mechanism does not scale well. The queuing of "no wait" devcmds is
done in firmware memory rather than on the host. Firmware memory is a
rather more scarce and valuable resource than host memory. A devcmd storm
from one vf can disrupt the service on other pf/vf. The lack of flow
control allows for possible denial of server from one VM to another.
Devcmd2 uses work queue to post the devcmds, just like tx work queue. This
allows better flow control.
Initialize devcmd2, if fails we fall back to devcmd1.
Also change the driver version.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devcmd resources to vnic_res_type. Add data types used by devcmd.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pr_info does not give any details about the interface involved. This patch
uses netdev_info for printing the message. Use dev_info where netdev is not
ready.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the structure definitions are in .c file to make them private to
that file. This patch moves the struct definition to .h file, So that their
definitions are accessible from other files.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN offloading is not functional if the NIC is running in multichannel
mode (UMC, FLEX-10, VNIC...). Enabling this additionally kills whole
connectivity through the NIC and the device needs to be down and up to
restore it. The firmware should take care about it and does not allow
the conversion of interface to tunnel type (be_cmd_manage_iface) or should
support VxLAN offloading if multichannel config is enabled.
I have tested this on the latest available firmware (10.6.144.21).
Result:
[root@sm-04 ~]# ip link set enp5s0f0 up[root@sm-04 ~]# ip addr add 172.30.10.50/24 dev enp5s0f0
[root@sm-04 ~]# ping -c 3 172.30.10.254PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.317 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.187 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.188 ms
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.187/0.230/0.317/0.063 ms
[root@sm-04 ~]# ip link add link enp5s0f0 vxlan10 type vxlan id 10 remote 172.30.10.60 dstport 4789
[root@sm-04 ~]# ip link set vxlan10 up
[ 7900.442811] be2net 0000:05:00.0: Enabled VxLAN offloads for UDP port 4789
[ 7900.455722] be2net 0000:05:00.1: Enabled VxLAN offloads for UDP port 4789
[ 7900.468635] be2net 0000:05:00.2: Enabled VxLAN offloads for UDP port 4789
[ 7900.481553] be2net 0000:05:00.3: Enabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
[root@sm-04 ~]# ip link set vxlan10 down
[ 7959.434093] be2net 0000:05:00.0: Disabled VxLAN offloads for UDP port 4789
[ 7959.444792] be2net 0000:05:00.1: Disabled VxLAN offloads for UDP port 4789
[ 7959.455592] be2net 0000:05:00.2: Disabled VxLAN offloads for UDP port 4789
[ 7959.466416] be2net 0000:05:00.3: Disabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ip link del vxlan10
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
[root@sm-04 ~]# ip link set enp5s0f0 down
[root@sm-04 ~]# ip link set enp5s0f0 up
[ 8071.019003] be2net 0000:05:00.0 enp5s0f0: Link is Up
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.318 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.196 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.194 ms
--- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.194/0.236/0.318/0.057 ms
Cc: Sathya Perla <sathya.perla@avagotech.com>
Cc: Ajit Khaparde <ajit.khaparde@avagotech.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Ajit Khaparde <ajit.khaparde@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b50dc4fc9 ("Convert smsc911x to use ACPI as well as DT") makes
the call to smsc911x_probe_config() unconditional, and no longer fails if
there is no device node. device_get_phy_mode() is called unconditionally,
and if there is no phy node configured returns an error code. This error
code is assigned to phy_interface, and interpreted elsewhere in the code
as valid phy mode. This in turn causes qemu to crash when running a
variant of realview_pb_defconfig.
qemu: hardware error: lan9118_read: Bad reg 0x86
Fixes: 0b50dc4fc9 ("Convert smsc911x to use ACPI as well as DT")
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_mapping_error() function returns true or false. We should
return -ENOMEM if it there is a dma mapping error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.
For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed. In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.
Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY. Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops. The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down). This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device. In response, the driver will
purge the neigh entry from its internal tbl.
I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users. In any case, it
does what I need here. An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sucessful probe, driver prints the switch ID. This patch changes the
format of the printed ID to match what's used in sysfs phys_switch_id node.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI bindings for the smsc911x driver. Convert the DT specific calls
to nonspecific device* calls, This allows the driver to work
with both ACPI and DT configurations. Ethernet should now work when using
ACPI on ARM Juno.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.
[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support to dump tid info like stid, sftid, tids, atid and
hwtids
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T4 adapter, offloaded servers tid for IPv4 connections are
allocated from filter region. So add a new field for server filter tid if
server tid is allocated from filter region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the tid info, differentiate from which region the TID is allocated
from. It can be from TCAM region or HASH region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding more details to sge qinfo for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BQL implementation is mostly derived from its related driver, alx.
Tested on AR8131 (rev c0) [1969:1063]. Saturated a 100mbps link with 5
concurrent runs of netperf. Ping latency dropped from 14ms to 3ms.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime. Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.
Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way to get the MAC address in a firmware
independent manner, so set the MAC address of the device directly from
the ACPI tables.
The binding agrees with the proposed standard here:
http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf
Based on code from: Narinder Dhillon <ndhillon@cavium.com>
Tomasz Nowicki <tomasz.nowicki@linaro.org>
Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate DT code in preparation for follow-on ACPI integration.
Based on code from: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use '%zx' to print size_t format in order to fix the following build warning:
drivers/net/ethernet/mellanox/mlxsw/item.h:65:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type 'size_t' [-Wformat=]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some tabs so that statements line up correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.
Fixes: 3ccc6cf74d ('cxgb4: Adds support for T6 adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include local headers files after kernel's header files.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).
When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.
The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.
This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.
This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.
This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.
This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reported-by: Alexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.
Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
failed to configure the page size for architectures with page size
different than 4K.
Fixes: 938fe83 ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are paths in the driver such as an unrecoverable error (UE) detection
followed by a driver unload wherein be_clear() is invoked twice.
Individual data structures are reset so that they are not cleaned/freed
twice. This patch does the same for eqo->affinity_mask. It is freed only
if EQs haven't yet been destroyed. This fixes a possible crash when
affinity_mask is freed twice.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An RX stall issue was seen on Lancer adapters, when RXQs are destroyed
while they are in an "out of buffer" state. This patch fixes this issue
by posting 64 buffers to each RXQ before destroying them in the close path.
This is done after ensuring that no more new packets are selected for
transfer to the RXQs by disabling interface filters.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW issues were observed on Lancer adapters if IFACE filters
(flags, mac addrs etc) are enabled *before* creating RXQs. This patch
changes the driver design by enabling filters in be_open() --
instead of be_setup() -- after RXQs are created and buffers posted.
Two new wrapper functions, be_enable_if_filters() and
be_disable_if_filters() are introduced to enable/disable IFACE filters in
be_open()/be_close() respectively. In be_setup() the IFACE is now created
only with the RSS flag.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-05
This series contains updates to i40e, i40evf and e1000e.
Anjali adds support for x772 devices to i40e and i40evf. With the added
support, x772 supports offloading of the outer UDP transmit and receive
checksum for tunneled packets. Also supports evicting ATR filters in the
hardware, so update the driver with this new feature set.
Raanan provides several fixes for e1000e, first rectifies the Energy
Efficient Ethernet in Sx code so that it only applies to parts that
actually support EEE in Sx. Fix whitespace and moved ICH8 related define
to the proper context. Fixed the ASPM locking which was reported by
Bjorn Helgaas. Fix a workaround implementation for systime which could
experience a large non-linear increment of the systime value when
checking for overflow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch b1c17215d718: "stmmac: add ipq806x glue layer", leads to the
following static checker warning:
.../stmmac/dwmac-ipq806x.c:314 ipq806x_gmac_probe()
warn: double left shift '1 << (1 << gmac->id)'
The NSS_COMMON_CLK_SRC_CTRL_OFFSET macro is used once as an offset, and
once as a mask, which is a bug indeed. We'll fix it by defining the
offset as the real offset value and computing the mask from it when
required.
Tested on IPQ806x ref designs AP148 & DB149.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface). This patch
removes the rx buffer size configuration capability.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as for kernels built only for ThunderX ARCH_THUNDERX is also enabled
for kernels which support multiple platforms (such as distro kernels). Thus
"default ARCH_THUNDER" is inappropriate.
I believe default m is equally frowned upon, so remove the line completely
rather than "default m if ARCH_THUNDER".
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Derek Chickles <derek.chickles@caviumnetworks.com>
Cc: Satanand Burla <satananda.burla@caviumnetworks.com>
Cc: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Cc: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]
Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Alexander Lindqvist <alexander@bitspace.se>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TIRs, TISs and flow tables are kept alive while the netdev is
stopped (after executing ndo_stop()) we can do the following
improvements:
- Obsolete the active_vlans SW shadow.
- Do not delete/add flow table rules upon ndo_stop/open.
In addition to simplifying the flow, this change also fastens
the ndo_open/close operations.
- Obsolete synchronization of threads accessing the flow tables
with the netdev stop/open threads.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not make sense to allow events while the netdev is
unregistered.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions that used to be invoked upon ndo_open/stop and
are now invoked upon create/destroy_netdev() in order to better hint
their place in the flow.
Change some functions location in the file so that functions involved
in ndo_open/stop flow will not be interleaved with other functions.
This is a cosmetic change, no logical change here.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX traffic routed to this RQ will be silently dropped, at the NIC HW
level.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally an RX packet flows through the following objects:
Flow table --> TIR --> RQT --> RQ
Where:
- TIR stands for "Transport Interface Receive", defining the RSS and
LRO paramaters.
- RQT stands for "RQ Table", implementing the RSS indirection table.
- RQ stands for "Receive Queue"
For flows that do not need LRO, nor RSS, the driver made a shortcut to
the above RX flow by pointing to the RQ directly from the TIR, yielding
this flow:
Flow table --> TIR --> RQ
In this commit we remove this shortcut by "inserting" a single-RQ RQT
between the TIR and the RQ, i.e RX packets will reach the same RQ but
will go through an RQT of size 1, pointing to just a single RQ.
This way the RX traffic re-direction to/from the "Drop RQ" will be more
uniform (AKA "one flow"), as it will involve only RQTs re-direction and
no TIRs re-direction.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful register_netdev, we can use netdev_err rather the more
generic dev_err.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set port to NULL if port probe fails so we don't try to remove partially
initialized port on port probe err cleanup path.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 does NVM update via the adminq queue, so we need to add support for
that.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports evicting ATR filters in the HW. With this patch, we enable
the feature in the driver and avoid filter deletion by the driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the firmware API update to support the new X722 device.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump edc bist status for ECC data errors
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug support to dump memory address ranges of various hardware
modules of the adapter.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vortex_up is failed, the skb buffers allocated by __netdev_alloc_skb
in vortex_open are not released, which may cause resource leaks.
This bug has been submitted before.
This patch modifies the error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rocker supports the transmission of scattered packets, so let the kernel
know about it by setting the NETIF_F_SG bit in the device's features.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice in 'rocker_remove_ports', we should
also free the allocated 'net_device' structure. Do that by calling
'free_netdev' after unregistering it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 4b8ac9660a ("rocker: introduce rocker switch driver")
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 50649ab149 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab149 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab149 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy in the net driver is to attempt MCDI commands and
then handle any EPERM error codes appropriately when returned
by unprivileged functions.
The ethtool selftest contains some tests which are useful on
an unprivileged function, such as the event queue interrupt
tests, but other tests cannot be performed as the function
does not have the required permissions.
If a test returns -EPERM, act as though the test was not run
and continue.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has broken
compilation when CONFIG_BNX2X_SRIOV is not set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the previously introduced Mellanox Switch infrastructure and
add driver for SwitchX-2 ASIC. Note that this driver is very simple now.
It implements bare minimum for getting device to work on slow-path.
Fast-path offload functionality is going to be added soon.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet Management Datagrams (EMADs) are Ethernet packets sent between
the host and the device in order to configure the available device registers.
Another use case is notifications sent from the device to the host,
letting it know about certain events, such as port up / down.
Add the ability to construct EMADs with provisions to construct and
parse the registers' payloads. Implement EMAD transaction layer
which is responsible for the reliable transmission of EMADs. Also, add
an infrastructure used by the switch driver to register for particular
events generated by the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI bus implementation for Mellanox Technologies Switch ASICs. This
includes firmware initialization, async queues manipulation and command
interface implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core components of Mellanox switch driver infrastructure.
Core infrastructure is designed so that it can be used by multiple
bus drivers (PCI now, I2C and SGMII are planned to be implemented
in the future). Multiple switch kind drivers can be registered as well.
This core serves as a glue between buses and drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper typecasting while performing byte-by-byte copy
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vxlan offload specific counters to ethtool stats. We
provide tx/rx queue counters to show the number of vxlan offload pkts
sent/received.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cortina phy does not have kernel driver and we don't attach
device with phy layer for intefaces like XFI, XLAUI etc,
Hence check for interface type before calling disconnect.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when changing rss with multiple traffic flows.
While interface teardown, disable tx queues after all NAPI threads
are done. If done otherwise tx queues might be woken up inside NAPI
if any CQE_TX are processed.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a txq (SQ) remains in stopped state after this timeout its
considered as stuck and interface is reinited.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TXQ is wakedup whenever napi is executed
and irrespective of if any CQE_TX are processed or not.
Added 'txq_stop' and 'txq_wake' counters to aid in debugging
if there are any future issues.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppressing standard alloc_pages() warnings. Some kernel configs limit
alloc size and the network driver may fail. Do not drop a kernel
warning in this case, instead just drop a oneliner that the network
driver could not be loaded since the buffer could not be allocated.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing TSO packages not being counted.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for memory leak when changing queue/channel count via ethtool
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With earlier configured value sufficient number of CQEs are not
being reserved for transmitted packets. Hence under heavy incoming
traffic load, receive notifications will take away most of the CQ
thus transmit notifications will be lost resulting in tx skbs not
being freed.
Finally SQ will be full and it will be stopped, watchdog timer
will kick in. After this fix receive notifications will not take
morethan half of CQ reserving the rest for transmit notifications.
Also changed CQ & SQ sizes from 16k to 4k.
This is also due to the receive notifications taking first half of
CQ under heavy load and time taken by NAPI to clear transmit notifications
will increase with higher queue sizes. Again results in SQ being stopped.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed 'tso_hdrs' memory not being freed properly.
Also fixed SQ skbuff maintenance issues.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching back to LDD transactions from LDWB.
While transmitting packets out with LDWB transactions
data integrity issues are seen very frequently.
hence switching back to LDD.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.
This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was used to update netdev priv parameters that require stopping
and re-opening the device in a generic way - it got the new
parameters and did: ndo_stop(), copy new parameters into current
parameters, ndo_open().
We chose to remove it for two reasons:
1) It requires additional instance of struct mlx5e_params on the
stack and looking forward we expect this struct to grow.
2) Sometimes we want to do additional operations (besides
just updating the priv parameters) while the netdev is stopped.
For example, updating netdev->mtu @mlx5e_change_mtu() should
be done while the netdev is stopped (done in this commit).
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce access functions to create/destroy RSS indrection table
and use it in the Ethernet driver.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is un-named at this time.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the already defined rq pointer directly.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not needed by the mlx5 Eth driver since it has a CQ per RQ/SQ.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field already exists under the mlx5e_params struct
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The page size of the device's RQ/SQ/CQ objects is defined in 4K
units regardless of the system pages size.
Thus using the Linux's PAGE_SHIFT macro yields wrong device
configuration in systems where PAGE_SHIFT!=12.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_cmd_exec() might fail - need to check return value.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of defconfig consolidation using fragments, we'd like to be
able to have the same drivers enabled on 32-bit and 64-bit. Gianfar
happens to only exist on 32-bit systems, and when building the
resulting 64-bit kernel warnings were produced.
A couple of the warnings are trivial, but the rfbptr code has deeper
issues. It uses the virtual address as the DMA address, which again,
happens to work in the environments where this driver is currently
used, but is not the right thing to do.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation
support")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clean up error handle code to use goto label properly. In some
cases, the code unnecessarily use goto instead of just returning the error
code. Code also make explicit calls to devm_* APIs on error which is
not necessary. In the gbe_remove() also it makes similar calls which is
also unnecessary.
Also fix few checkpatch warnings
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code seems to assume a null is returned when the list is empty
from first_sec_slave() to break the loop which is incorrect. Fix the
code by using list_empty().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if user do rmmod keystone_netcp.ko following warning is
seen :-
[ 59.035891] ------------[ cut here ]------------
[ 59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/
netcp_core.c:2127 netcp_remove)
This is because the interface list is not cleaned up in netcp_remove.
This patch fixes this. Also fix some checkpatch related warnings.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_MDIO_OCTEON is required so that the ThunderX NIC driver can
talk to the PHY drivers.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped. To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action. The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2> under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix mistakenly used, hard coded, port number in get_phv_bit()
Fixes: 77fc29c ("net/mlx4_core: Preparations for 802.1ad VLAN support")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally the tilegx networking shim sends irqs to all the cores
to distribute the load of processing incoming-packet interrupts,
so that you can get to multiple Gb's of traffic inbound.
However, in nohz_full mode we don't want to interrupt the
nohz_full cores by default, so we limit the set of cores we use
to only the online housekeeping cores.
To make client code easier to read, we introduce a new nohz_full
accessor, housekeeping_cpumask(), which returns a pointer to the
housekeeping_mask if nohz_full is enabled, and otherwise returns
the cpu_possible_mask.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Remove the two platform specific init callbacks and make
them use a common one by creating a function member in
the internal data structure. This allow us to remove the
layer of indirection and simplify the code a bit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setup glue callback and use rk_gmac_ops as OF match
data so it can used directly when calling rk_gmac_setup.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the rk_gmac_ops structures as static const as they should be.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new private structure for OF match data in the
dwmac-sti driver. This enables us to eventually drop the
common OF match data structure which contains a lot of
unused fields.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since only a few of the dwmac-* drivers actually need to use
the OF match move handling into the dwmac-* drivers that need
it. This will also allow dwmac-* drivers to use their own
custom match data structure.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers now have their own probe function move
the common one into dwmac-generic driver and drop the EXPORT.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new probe functions that call the necessary setup
functions. This is done in preparation for a code refactor
in this driver and dropping the common probe function in
stmmac_platform.c.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and prepares the
driver for further clean ups.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sun7i_gmac_setup in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move socfpga_dwmac_probe in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ipq806x_gmac_fix_mac_speed in preparation for turning
the setup glue callback in a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:304:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[je: rebase and insert newline before return]
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a platform driver for the new generation of the
gigabit ethernet IP from Synopsys. It is developed for version 4.10a
of the IP core.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable device support in accelerated 802.1ad vlan, the port
capability "packet has vlan enable" (phv_en) should be set.
Firmware won't work properly, in case phv_en is not set.
The user can enable "phv_en" port capability with the new ethtool
private flag phv-bit. The phv-bit private flag default value is OFF,
users who are interested in 802.1ad hardware acceleration should turn ON
the phv-bit private flag:
$ ethtool --set-priv-flags eth1 phv-bit on
Once the private flag is set, the device is ready for 802.1ad vlan
acceleration.
The user should also change the interface device features and turn on
"tx-vlan-stag-hw-insert" which is off by default:
$ ethtool -K eth1 tx-vlan-stag-hw-insert on
"phv-bit" private flag setting is available only for Physical
Functions(PF), the Virtual Function (VF) will be able to use the feature
by setting "tx-vlan-stag-hw-insert" ethtool device feature only if the
feature was enabled by the Hypervisor.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To add Hardware accelerated support in 802.1ad vlan, replace
Current VLAN macros to CVLAN.
Replace:
MLX4_WQE_CTRL_INS_VLAN
MLX4_CQE_VLAN_PRESENT_MASK
With:
MLX4_WQE_CTRL_INS_CVLAN
MLX4_CQE_CVLAN_PRESENT_MASK
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support only one ethtool private flag. Prepare
mlx4_en_set_priv_flags function to support more than one private flag.
Will be used in the next patch to support hardware accelerated 802.1ad
vlan.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_core preparation to support hardware accelerated 802.1ad VLAN
device.
To allow 802.1ad accelerated device, "packet has vlan" (phv)
Firmware capability should be available. Firmware without the
phv capability won't behave properly and can't support 802.1ad device
acceleration.
The driver checks the Firmware capability and sets the phv bit
accordingly in SET_PORT command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas Ethernet AVB controller requires that all data are aligned on 4-byte
boundary. While it's easily achievable for the RX data with the help of
skb_reserve() (we even align on 128-byte boundary as recommended by the manual),
we can't do the same with the TX data, and it always comes unaligned from
the networking core. Originally we solved it an easy way, copying all packet
to a preallocated aligned buffer; however, it's enough to copy only up to
3 first bytes from each packet, doing the transfer using 2 TX descriptors
instead of just 1. Here's an implementation of the new TX algorithm that
significantly reduces the driver's memory requirements.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.
Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: tyler.baker@linaro.org
Cc: fabio.estevam@freescale.com
Cc: shawn.guo@linaro.org
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch asserts SGMII RTRESET, i.e. resetting the SGMII Tx/Rx
logic, during network interface shutdown to avoid having the
hardware wedge when shutting down with high incoming traffic rates.
This is cleared (brought out of RTRESET) when the interface is
brought back up.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch
does a replacement.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warnings:
drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’:
drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’:
drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’:
drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid messages like
macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000
macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random
let's use dev_*() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 98b5a0f4a2 introduces jumbo frame support, but also it assumes
that macb_config present which is not always true.
The configuration without macb_config fails to boot.
Unable to handle kernel NULL pointer dereference at virtual address 00000010
ptbr = 90350000 pgd = 00000000
Oops: Kernel access of bad area, sig: 11 [#1]
FRAME_POINTER chip: 0x01f:0x1e82 rev 2
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0-rc3-next-20150723+ #13
task: 91c26000 ti: 91c28000 task.ti: 91c28000
PC is at macb_probe+0x140/0x61c
Fixes: 98b5a0f4a2 (net: macb: Add support for jumbo frames)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a50dad355a (net: macb: Add big endian CPU support) converted I/O
accessors to readl_relaxed() and writel_relaxed() and consequentially broke
MACB driver on AVR32 platforms such as ATNGW100.
This patch improves I/O access by checking endiannes first and use the
corresponding methods.
Fixes: a50dad355a (net: macb: Add big endian CPU support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the source/destination IP which are already hashed.
Only for unicast traffic for now.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No logical change in this commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A regular TX WQE execution involves two or more DMA reads -
one to fetch the WQE, and another one per WQE gather entry.
These DMA reads obviously increase the TX latency.
There are two mlx5 mechanisms to bypass these DMA reads:
1) Inline WQE
2) Blue Flame (BF)
An inline WQE contains a whole packet, thus saves the DMA read/s
of the regular WQE gather entry/s. Inline WQE support was already
added in the previous commit.
A BF WQE is written directly to the device I/O mapped memory, thus
enables saving the DMA read that fetches the WQE.
The BF WQE I/O write must be in cache line granularity, thus uses
the CPU write combining mechanism.
A BF WQE I/O write acts also as a TX doorbell for notifying the
device of new TX WQEs.
A BF WQE is written to the same I/O mapped address as the regular TX
doorbell, thus this address is being mapped twice - once by ioremap()
and once by io_mapping_map_wc().
While both mechanisms reduce the TX latency, they both consume more CPU
cycles than a regular WQE:
- A BF WQE must still be written to host memory, in addition to being
written directly to the device I/O mapped memory.
- An inline WQE involves copying the SKB data into it.
To handle this tradeoff, we introduce here a heuristic algorithm that
strives to avoid using these two mechanisms in case the TX queue is
being back-pressured by the device, and limit their usage rate otherwise.
An inline WQE will always be "Blue Flamed" (written directly to the
device I/O mapped memory) while a BF WQE may not be inlined (may contain
gather entries).
Preliminary testing using netperf UDP_RR shows that the latency goes down
from 17.5us to 16.9us, while the message rate (tested with pktgen) stays
the same.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AKA inline WQE.
A TX latency optimization to save data gather DMA reads.
Controlled by ETHTOOL_TX_COPYBREAK.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By affinity hints and XPS, each mlx5e channel is assigned a CPU
core.
Channel DMA coherent memory that is written by the NIC and read
by SW (e.g CQ buffer) is allocated on the NUMA node of the CPU
core assigned for the channel.
Channel DMA coherent memory that is written by SW and read by the
NIC (e.g SQ/RQ buffer) is allocated on the NUMA node of the NIC.
Doorbell record (written by SW and read by the NIC) is an
exception since it is accessed by SW more frequently.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing statistics for the host
and slave ports of the CPSW on K2L and K2E platforms.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain applications it's beneficial to allow the CPSW h/w
stats counters to continue to increment even while the kernel
polls them. This patch implements this behavior for both 1G
and 10G ethernet subsystem modules.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different Keystone2 platforms have different number and
layouts of hw statistics modules. This patch consolidates
the statistics processing of different Keystone2 platforms
for easy maintenance.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW driver keeps internally some, but not all, of
the statistics available in the hw statistics modules. Furthermore,
some of the locations in the hw statistics modules are reserved and
contain no useful information. Prior to this patch, the driver
allocates memory of the size of the the whole hw statistics modules,
instead of the size of statistics-entries-interested-in (i.e. et_stats),
for internal storage. This patch fixes that.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes error in the setting of the hw statistics
module base for K2HK platform. In K2HK although there are
4 hw statistics modules, but only 2 are visible at a time.
Thus when setting up the pointers to the base of the
corresponding hw statistics modules, modules 0 and 2 should
point to one base, while modules 1 and 3 should point to the
other.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in which the timer routine synchronized
against the ethtool-triggered statistics updates with spin_lock_bh().
A timer function is itself a bottom-half, so this should be
spin_lock().
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function frees resources and cancels delayed work item that
have been initialized in fec_ptp_init().
Use this to do proper error handling if something goes wrong in
probe function after fec_ptp_init has been called.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it gets freed when the device is going away.
This fixes a DMA memory leak on driver probe() fail and driver
remove().
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver was reading incorrect freelist congestion notification threshold
for FLM queues when packing is enabled for T5 and T6 adapter. Fixing it
now.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a3138df9 ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
JUMBO and NO_GIGABIT_HALF have the same capability masks.
Change one of them.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change
detection") added a fixed PHY link_update callback for MoCA PHYs when
registered using platform_data exclusively, this change is also
applicable to systems using Device Tree as their primary configuration
interface.
In order for this to work, move the link_update assignment into
bcmgenet_moca_phy_setup() where we know for sure that we are running on
a MoCA GENET instance, and do not override phydev->link since this is:
- properly taken care of by the PHY library by getting the link UP/DOWN
interrupts
- this now runs everytime we call bcmgenet_open(), so we need to
preserve whatever we detected before we went administratively DOWN and
then UP
- we need to make sure that MoCA PHYs start with a link DOWN during
probe in order to force a link transition to occur
To avoid a forward declaration, move bcmgenet_fixed_phy_link_update()
above its caller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of multiplying the number of checks for IS_ERR(priv->clk),
simply NULLify the 'struct clk' pointer which is something the Linux
common clock framework perfectly deals with and does early return for
each and every single clk_* API functions.
Having every single function check for !IS_ERR(priv->clk) is both
redundant and error prone, as it turns out, we were doing it for the
main GENET clock: priv->clk, but not for the Wake-on-LAN or EEE clock,
so let's just be consistent here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter can go for a toss, if cxgb4 is loaded as slave and we try to
upgrade the firmware. So add a check for the same before flashing
firmware using ethtool.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx4_en_is_ring_empty we check if ring surpassed its size.
Since the prod and cons indicators are u32, there might be a state where
prod wrapped around and cons, making this assert false, although no
actual bug exists (other code segment can cope with this state).
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is not attached, the FW requires a longer than usual time to
execute the SENSE_PORT command. In the command flow, the
wait_for_completion_timeout call used in mlx4_cmd_wait puts the kernel
thread into the uninterruptible state during this time. This, in turn,
due to the computation method, causes the CPU load average to increase.
Fix this by using wait_for_completion_interruptible_timeout() for the
SENSE_PORT command, which puts the thread in the interruptible state.
In this state, the thread does not contribute to the CPU load average.
Treat the interrupted case as if the SENSE_PORT command returned
port_type = NONE.
Fix suggested by Gideon Naim <gideonn@mellanox.com> and
Bart Van Assche <bart.vanassche@sandisk.com>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port-change event processing in procedure mlx4_eq_int() uses "slave"
as the vf_oper array index. Since the value of "slave" is the PF function
index, the result is that the PF link state is used for deciding to
propagate the event for all the VFs. The VF link state should be used,
so the VF function index should be used here.
Fixes: 948e306d7d ('net/mlx4: Add VF link state support')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some old PF drivers don't let VFs allocate counters, in that case, use
the sink counter so the VF can load and operate properly.
Fixes: 6de5f7f6a1 ('net/mlx4_core: Allocate default counter per port')
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-07-23
This series contains updates to e1000e, igb, ixgbevf, i40e and i40evf.
Emil extends the reporting of the RSS key and hash table by adding support
for x550 VFs.
Jia-Ju Bai fixes a QoS issue in e1000e where the error handling lacked a
call to pm_qos_remove_request() to cleanup the QoS request made in
e1000_open().
Todd updates igb to report unsupported for ethtool coalesce settings
that are not supported. Also updated the driver to use the ARRAY_SIZE()
macro.
Carolyn fixes and refactors the dynamic ITR code for i40e and i40evf
which would never change dynamically. So update the switch() statement
to have a default case and switch on "new_latency_range" versus the
current ITR setting.
Shannon cleans up i40e code, where there were un-needed goto's. Also
clean up error status messages that were causing some confusion in
PHY and FCoE setup error reports.
Mitch updates the virtual channel interface to prepare for the x722 device
and other future devices, so that the VF driver can report what its
capable of supporting to the PF driver. Updates the i40evf driver to
handle resets like Core or EMP resets, where the device is reinitialized
and the VF will not get the same VSI.
Jesse updates the i40e and i40evf driver to use the kernel BIT() and
BIT_ULL() macros.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add be_get_phys_port_id() function to report physical port id. The port id
should be unique across different be2net devices in the system. We use the
chip serial number along with the physical port number for this.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.
Add two decoder functions to make this easier.
Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver fully supports VF drivers using both the 1.0 and 1.1
versions of the virtual channel API. However, VF drivers using
version 1.0 get upset if we provide them with a version other than
that, and refuse to play with us.
Correct this by checking the VFs API version at the time that we
store it off, and provide the correct version number back to the VF
so we can all get along.
Change-ID: I86dfe02e67b2bef336b4b49a1bb072f3e7229abc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the PF's API version, then use it to determine whether or not
to send it our capabilities. Change the version checking to allow for PF
drivers with lower API versions than our current version, so we can
still talk to PF drivers over the 1.0 API.
Change-ID: I8edc55d1229c7decf0ed3f285a63032694007c2e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The most common type of reset that the VF will encounter is a PF reset
that cascades down into a VF reset for each VF. In this case, the VF
will always be assigned the same VSI and recovery is fairly simple.
However, in the case of 'bigger' resets, such as a Core or EMP reset,
when the device is reinitialized, it's probable that the VF will NOT get
the same VSI. When this happens, the VF will not be able to recover, as
it will continue to request resources for its original VSI.
Add an extra state to the admin queue state machine so that the driver
can re-request its configuration information at runtime. During reset
recovery, set this bit in the aq_required field, and fetch the (possibly
new) configuration information before attempting to bring the driver
back up. Since the driver doesn't know what kind of reset it has
encountered, this step is done even for a PF reset, but it doesn't hurt
anything - it just gets the same VSI back.
Change-ID: I915d59ffb40375215117362f4ac7a37811aba748
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the VF API version for use when figuring out the VF driver
capabilities. Add support for the VF driver handing its capabilities to
the PF driver and then use this information when sending VF resource
information back to the VF driver.
Change-ID: Ic00d0eeeb5b8118085e12f068ef857089a8f7c2d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.
Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.
A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.
All other aspects of the API are unchanged.
Change-ID: I530cc55f107edd1ee8bdf95830aa90b87854058a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a little work we can clean up some unnecessary logic jumping and
drop a variable.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the switch statement for dynamic interrupt throttling
and adds a default case. With this patch, we check the latency setting
instead of the current ITR settings and the included refactor improves
performance.
Without this patch, the ITR setting would never change dynamically, and
there was no default.
Change-ID: Idb5a8a14c7109ec47c90f6e94bd43baa17d7ee37
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ARRAY_SIZE macro rather than calculating sizeof(a)/sizeof(a[0]).
Also directly replace the code rather than using an unnecessary define.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many settings possible using ethtool -C/--coalesce, but not
all of them are supported in igb. Report failure when an unsupported
option is set.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the reporting of the RSS key and hash table by
adding support for X550 VFs. The difference is that X550 VFs have
their own registers for RSS key and indirection table, so there is
no need to query the PF.
The RSS key and indirection table are stored in the adapter structure
during the configuration of VFRSSRK and VFRETA which in turn can be
used in ethtool for reporting.
The logic for writing VFRETA is also changed to make sure that the
indirection table is reported correctly.
In addition this patch adds defines for the VFRETA entries and number
of VFRSSRK registers as well as some whitespace cleanups.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't use shared bluetooth antenna in iwlwifi driver for management
frames, from Emmanuel Grumbach.
2) Fix device ID check in ath9k driver, from Felix Fietkau.
3) Off by one in xen-netback BUG checks, from Dan Carpenter.
4) Fix IFLA_VF_PORT netlink attribute validation, from Daniel Borkmann.
5) Fix races in setting peeked bit flag in SKBs during datagram
receive. If it's shared we have to clone it otherwise the value can
easily be corrupted. Fix from Herbert Xu.
6) Revert fec clock handling change, causes regressions. From Fabio
Estevam.
7) Fix use after free in fq_codel and sfq packet schedulers, from WANG
Cong.
8) ipvlan bug fixes (memory leaks, missing rcu_dereference_bh, etc.)
from WANG Cong and Konstantin Khlebnikov.
9) Memory leak in act_bpf packet action, from Alexei Starovoitov.
10) ARM bpf JIT bug fixes from Nicolas Schichan.
11) Fix backwards compat of ANY_LAYOUT in virtio_net driver, from
Michael S Tsirkin.
12) Destruction of bond with different ARP header types not handled
correctly, fix from Nikolay Aleksandrov.
13) Revert GRO receive support in ipv6 SIT tunnel driver, causes
regressions because the GRO packets created cannot be processed
properly on the GSO side if we forward the frame. From Herbert Xu.
14) TCCR update race and other fixes to ravb driver from Sergei
Shtylyov.
15) Fix SKB leaks in caif_queue_rcv_skb(), from Eric Dumazet.
16) Fix panics on packet scheduler filter replace, from Daniel Borkmann.
17) Make sure AF_PACKET sees properly IP headers in defragmented frames
(via PACKET_FANOUT_FLAG_DEFRAG option), from Edward Hyunkoo Jee.
18) AF_NETLINK cannot hold mutex in RCU callback, fix from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
ravb: fix ring memory allocation
net: phy: dp83867: Fix warning check for setting the internal delay
openvswitch: allocate nr_node_ids flow_stats instead of num_possible_nodes
netlink: don't hold mutex in rcu callback when releasing mmapd ring
ARM: net: fix vlan access instructions in ARM JIT.
ARM: net: handle negative offsets in BPF JIT.
ARM: net: fix condition for load_order > 0 when translating load instructions.
tcp: suppress a division by zero warning
drivers: net: cpsw: remove tx event processing in rx napi poll
inet: frags: fix defragmented packet's IP header for af_packet
net: mvneta: fix refilling for Rx DMA buffers
stmmac: fix setting of driver data in stmmac_dvr_probe
sched: cls_flow: fix panic on filter replace
sched: cls_flower: fix panic on filter replace
sched: cls_bpf: fix panic on filter replace
net/mdio: fix mdio_bus_match for c45 PHY
net: ratelimit warnings about dst entry refcount underflow or overflow
caif: fix leaks and race in caif_queue_rcv_skb()
qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
ravb: fix race updating TCCR
...
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.
This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new copper phy.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.
This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:
- Packets from a VF with pvid configured which were sent with a
different vlan were transmitted instead of being discarded.
- FCoE traffic might not recover after a failue while there's traffic
to another function.
In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is written as if it can adapt to a low memory situation allocating
less RX skbs and TX aligned buffers than the respective RX/TX ring sizes. In
reality though the driver would malfunction in this case. Stop being overly
smart and just fail in such situation -- this is achieved by moving the memory
allocation from ravb_ring_format() to ravb_ring_init().
We leave dma_map_single() calls in place but make their failure non-fatal
by marking the corresponding RX descriptors with zero data size which should
prevent DMA to an invalid addresses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate functions for inserting individual and promisc filters; explicit
fallback logic in efx_ef10_filter_sync_rx_mode(), in order not to overload
the 'promisc' flag as also meaning "fall back to promisc".
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the workaround to support cascaded multicast filters ("workaround_26807") is
enabled, the broadcast filter and individual multicast filters are not inserted
when in promiscuous or allmulti mode.
There is a race while inserting and removing filters when entering and leaving
promiscuous mode. When changing promiscuous state with cascaded multicast
filters, the old multicast filters are removed before inserting the new filters
to avoid duplicating packets; this can lead to dropped packets until all
filters have been inserted.
The efx_nic:mc_promisc flag is added to record the presence of a multicast
promiscuous filter; this gives a simple way to tell if the promiscuous state is
changing.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is only re-factoring; there are no changes to functionality
except for a slight elaboration of an error message (on mismatch filter
insertion failure).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a function is in promiscuous mode and another function has a broadcast or
multicast filter inserted, the function in promiscuous mode won't see that
broadcast or multicast traffic.
Most notably this breaks broadcast, which means ARP doesn't work. Less
show-stoppingly, a function listening on a multicast address that's also in
promiscuous mode will not see that multicast traffic if another function is
also listening on that multicast address.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the workaround for cascaded multicast filters, the MC
can reset other functions if they have already inserted filters.
In that case, the workaround has been enabled, but print an info
message in the log recording that other functions had to be reset.
As other functions were reset, the MC will have incremented its boot
count, so also increment the warm_boot_count on the function which
enabled the workaround, as that function won't have received an MC
reboot event and does not need to reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial use of this will be to check a flag reporting if an FLR was
performed on other functions when enabling cascaded multicast filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GET_WORKAROUNDS was only introduced in May 2014, not all firmware
will have it. So call sites need to handle ENOSYS.
In this case we're probing the bug26807 workaround, which is not
implemented in any firmware that doesn't have GET_WORKAROUNDS.
So interpret ENOSYS as 'false'.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller