Packets destined to offloaded netdevs will be classified to FIDs in the
device and flooded in case of BUM.
The flooding table used is of type FID-offset, which allows one to
create different flooding domains for different FIDs and specify the
offset in the flooding table for each FID (not necessarily equal to FID
or VID).
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the newly introduced Spectrum switch ASIC, packets destined to not
offloaded netdevs will be classified to special FIDs (vFIDs) in the
device and flooded to the CPU port.
The flooding table used is of type per-FID, which allows one to create
different flooding domains for different vFIDs.
While using a simple single-entry flood table is certainly sufficient at
this point, we do plan to offload 802.1D bridges involving VLAN
interfaces, thus making this change necessary.
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the introduction of L2 offloads, allow different ports to
join/leave the flooding domain, according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.
Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.
Change-ID: I620221520d8af987df6ace9ba938ffaf22107681
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1000Base_T_Optical got added to the function that figures out what
is supported when link is down but not when link is up. Add it in there
too so that we display the correct information.
Change-ID: I85ebcdfa7c02d898c44c673b1500552a53c8042e
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vlan_features field was correctly being set to the same value as the
netdev features field. However, this was being done before the features
were actually being set up, leaving the vlan_features empty.
Also, after a reset, vlan_features will be incorrectly assigned the
previous netdev feature flags, which can contain VLAN feature bits. This
makes the VLAN code angry and will cause a stack dump.
To fix these issues, set up the netdev features first, then mask out the
VLAN feature bits when assigning vlan_features.
Change-ID: Ib0548869dc83cf6a841cb8697dd94c12359ba4d2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the number of invalid messages from a VF is exceeded, the VF
will be disabled, due to the invalid messages. This happens if
other VF drivers (like DPDK) send a message through the driver's
mailbox (aka virtchannel) interface, but the message is not
supported by the i40e pf driver, such as CONFIG_PROMISCUOUS_MODE.
This patch changes the num_invalid_msgs in struct i40e_vf to record
the continuous invalid msgs, and it will be reset when a valid msg
is received.
Change-ID: Iaec42fd3dcdd281476b3518be23261dd46fc3718
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for setting a new bit in the Set Local LLDP MIB AQ command
Type field. When set to 1, the bit indicates to FW that Apps should be
treated as non-willing. When 0, FW behaves as before.
Change-ID: I0d2101c1606c59c7188d3e6a0c7810e0f205233a
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool priv flag to enable and disable printing
the VEB statistics.
Change-ID: I7654054a3a73b08aa8310d94ee8fce6219107dd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two defines that are not used are causing customer confusion - remove
them.
Change-ID: Icef0325aca8e0f4fcdfc519e026bdd375e791200
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the nvmupdate application to decide when a read or write error
should be exposed to the user. Since the application needs to use
write probes to find the ReadOnly sections on a potentially unknown NVM
version in the HW and read probes to check the status of the last write,
some error messages are expected, but need not be shown to the users.
The driver doesn't know which are ignorable from real errors, so needs
to let the application make the decision.
Change-ID: I78fca8ab672bede11c10c820b83c26adfd536d03
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocation fails, mlx4_alloc_cmd_mailbox returns -ENOMEM.
Since there is no case that mlx4_alloc_cmd_mailbox returns NULL,
it needs to be checked by IS_ERR, not IS_ERR_OR_NULL
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The meaning of certain parameters in the profile passed to the device
during initialization has changed, so update their documentation
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we trapped flooded and control packets using the same trap
group. This can cause flooded packets to overflow the PCI bus and
prevent control packets (e.g. STP, LACP) from getting to the CPU.
Solve this by splitting the RX trap group to RX and control, which allows
us to configure a policer on the first, thereby preventing it from
overflowing the PCI bus.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Host Trap Group Table (HTGT) register configures trap groups, which
are populated with trap IDs using the Host PacKet Trap (HPKT) register.
However, a trap ID can only be present inside one trap group (the last
configured).
Instead of passing both the trap group and ID for the function that
packs HPKT, pass only the trap ID and derive from it the trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce separate helper for packing SPMS VIDs, as it can be used for
multiple VIDs and not only for one as previous SPMS pack function
provided.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define max which would be needed later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmetric with mlxsw_emad_init and don't use EMADs in mlxsw_emad_fini
cleanup function. Use command interface instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware accepts only limited number of mapping entries for MAP_FA
command. In order to prevent overflow, introduce a limit and in case the
number of entries is bigger, call MAP_FA multiple times.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove strict number check of queues count as various ASICs have
different counts.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The count of CQs can be different for various ASICs, so just define
maximal value and check for that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With respect to a firmware change, the Switch Multicast ID (SMID)
register is no longer needed, so the related configuration code can be
removed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch switched from using the system workqueue to the device
workqueue for various operations. During a device restart the device
workqueue is flushed so the restart cannot use this workqueue or else
a deadlock results. Move the device restart back to using the system
workqueue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to avoid sleeping in switchdev callbacks now, as the switchdev
core allows it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When object is used in deferred work, we cannot use pointers in
switchdev object structures because the memory they point at may be already
used by someone else. So rather do local copy of the value.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes a bug in hns driver. when we want to get statistic info
by using ethtool -S, it shows us there are 3 wrong counters info. because
the strings related to the registers are wrong. it needs to modify the
strings which give us wrong info.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only call the internal_setup_link method when it is provided. This
check is required for newer version parts.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten up the delays in the init task, allowing the VF driver to
initialize faster. This aids performance in load/unload tests and
mitigates DMAR errors in VF enable/disable tests with absurdly short
delays. In the real world, the VF driver will come up more quickly.
The original values were set conservatively based on what we expected
from the firmware in terms of performance. Now that the driver is in use
and we know how well firmware responds to our requests, we can shorten
these delays.
Change-ID: Ibead77d34b19e8170e667c3f58bc14748bbc5bc9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save a little stack space and remove unnecessary strncpy() with a little
string pointer.
Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.
Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off reported PHY capabilities in link_info structure.
Change-ID: Ife0f037c26983ca985dbf79abf33f8f8791369e8
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.
Also remove a forward function declaration that is no longer needed due
to code re-organization.
Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the flow-director-atr priv flag was added to our ethtool interface,
we don't need the on/off control in debugfs.
Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ido Schimmel