With 4 levels of 16KB pages, we get this warning about the fact that we are
copying a whole page into an array that is declared as having only two pointers
for the top level of the page table:
arch/arm64/mm/mmu.c: In function 'paging_init':
arch/arm64/mm/mmu.c:528:2: error: 'memcpy' writing 16384 bytes into a region of size 16 overflows the destination [-Werror=stringop-overflow=]
This is harmless since we actually reserve a whole page in the definition of the
array that comes from, and just the extern declaration is short. The pgdir
is initialized to zero either way, so copying the actual entries here seems
like the best solution.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Qualcomm Datacenter Technologies Falkor v1 CPU may allocate TLB entries
using an incorrect ASID when TTBRx_EL1 is being updated. When the erratum
is triggered, page table entries using the new translation table base
address (BADDR) will be allocated into the TLB using the old ASID. All
circumstances leading to the incorrect ASID being cached in the TLB arise
when software writes TTBRx_EL1[ASID] and TTBRx_EL1[BADDR], a memory
operation is in the process of performing a translation using the specific
TTBRx_EL1 being written, and the memory operation uses a translation table
descriptor designated as non-global. EL2 and EL3 code changing the EL1&0
ASID is not subject to this erratum because hardware is prohibited from
performing translations from an out-of-context translation regime.
Consider the following pseudo code.
write new BADDR and ASID values to TTBRx_EL1
Replacing the above sequence with the one below will ensure that no TLB
entries with an incorrect ASID are used by software.
write reserved value to TTBRx_EL1[ASID]
ISB
write new value to TTBRx_EL1[BADDR]
ISB
write new value to TTBRx_EL1[ASID]
ISB
When the above sequence is used, page table entries using the new BADDR
value may still be incorrectly allocated into the TLB using the reserved
ASID. Yet this will not reduce functionality, since TLB entries incorrectly
tagged with the reserved ASID will never be hit by a later instruction.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SPE architecture requires each exception level to enable access
to the SPE controls for the exception level below it, since additional
context-switch logic may be required to handle the buffer safely.
This patch allows EL1 (host) access to the SPE controls when entered at
EL2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we have a workaround for Hisilicon erratum 161010101, notes
this in the arm64 silicon-errata document.
The new config option is too long to fit in the existing kconfig column,
so this is widened to accomodate it. At the same time, an existing
whitespace error is corrected, and the existing pattern of a line space
between vendors is enforced for recent additions.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message, rework table]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
To is_vmalloc_addr() to check if an address is a vmalloc address
instead of checking VMALLOC_START and VMALLOC_END manually.
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently in arm64's copy_{to,from}_user, we only check the
source/destination object size if access_ok() tells us the user access
is permissible.
However, in copy_from_user() we'll subsequently zero any remainder on
the destination object. If we failed the access_ok() check, that applies
to the whole object size, which we didn't check.
To ensure that we catch that case, this patch hoists check_object_size()
to the start of copy_from_user(), matching __copy_from_user() and
__copy_to_user(). To make all of our uaccess copy primitives consistent,
the same is done to copy_to_user().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Adds perf events support for L2 cache PMU.
The L2 cache PMU driver is named 'l2cache_0' and can be used
with perf events to profile L2 events such as cache hits
and misses on Qualcomm Technologies processors.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Leeder <nleeder@codeaurora.org>
[will: minimise nesting in l2_cache_associate_cpu_with_cluster]
[will: use kstrtoul for unsigned long, remove redunant .owner setting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The sysfs cpu_capacity entry for each CPU has nothing to do with
PROC_FS, nor it's in /proc/sys path.
Remove such ifdef.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-and-suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: be8f185d8a ('arm64: add sysfs cpu_capacity attribute')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 680a0873e1 ("arm: kernel: Add SMC structure parameter") added
a new "quirk" parameter to the SMC and HVC SMCCC backends, but only
updated the comment for the SMC version. This patch adds the new
paramater to the comment describing the HVC version too.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Atomic operation function symbols are exported,when
CONFIG_ARM64_LSE_ATOMICS is defined. Prefix them with notrace, so that
an user can not trace these functions. Tracing these functions causes
kernel crash.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The function iort_add_smmu_platform_device() accidentally returns 0
(ie PTR_ERR(pdev) where pdev == NULL) if platform_device_alloc() fails;
fix the bug by returning a proper error value.
Fixes: 846f0e9e74 ("ACPI/IORT: Add support for ARM SMMU platform devices creation")
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[lorenzo.pieralisi@arm.com: improved commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 618f535a60 ("ACPI/IORT: Add single mapping function")
introduced a function (iort_node_get_id()) to retrieve ids for IORT
named components.
The iort_node_get_id() takes an index as input to refer to a specific
mapping entry in the named component IORT node mapping array.
For a mapping entry at a given index, iort_node_get_id() should return
the id value (through the id_out function parameter) and the IORT node
output_reference (through function return value) the given mapping entry
refers to.
Technically output_reference values may differ for different map
entries, (see diagram below - mapped id values may refer to different eg
IORT SMMU nodes; the kernel may not be able to handle different
output_reference values for a given named component but the IORT kernel
layer should still report the IORT mappings as reported by firmware) but
current code in iort_node_get_id() fails to use the index function
parameter to return the correct output_reference value (ie it always
returns the output_reference value of the first entry in the mapping
array whilst using the index correctly to retrieve the id value from the
respective entry).
|----------------------|
| named component |
|----------------------|
| map entry[0] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 1
|----------------------|
| map entry[1] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 2
|----------------------|
.
.
.
|----------------------|
| map entry[N] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 1
|----------------------|
Consequently the iort_node_get_id() function always returns the IORT
node pointed at by the output_reference value of the first named
component mapping array entry, irrespective of the index parameter,
which is a bug.
Update the map array entry pointer computation in iort_node_get_id() to
take into account the index value, fixing the issue.
Fixes: 618f535a60 ("ACPI/IORT: Add single mapping function")
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Nate Watterson <nwatters@codeaurora.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The NUMA code may get confused by the presence of NOMAP regions within
zones, resulting in spurious BUG() checks where the node id deviates
from the containing zone's node id.
Since the kernel has no business reasoning about node ids of pages it
does not own in the first place, enable CONFIG_HOLES_IN_ZONE to ensure
that such pages are disregarded.
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
I ran into a build error when I disabled CONFIG_ACPI and tried to
compile this driver:
drivers/perf/xgene_pmu.c:1242:1: warning: data definition has no type or storage class
MODULE_DEVICE_TABLE(of, xgene_pmu_of_match);
^
drivers/perf/xgene_pmu.c:1242:1: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE' [-Werror=implicit-int]
Include module.h for the MODULE_DEVICE_TABLE macro that's
implicitly included through ACPI.
Tested-by: Tai Nguyen <ttnguyen@apm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds a Qualcomm specific quirk to the arm_smccc_smc call.
On Qualcomm ARM64 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The quirk stores off the session ID from the interrupted call in the
quirk structure so that it can be used by the caller.
This patch folds in a fix given by Sricharan R:
https://lkml.org/lkml/2016/9/28/272
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds a quirk parameter to the arm_smccc_(smc/hvc) calls.
The quirk structure allows for specialized SMC operations due to SoC
specific requirements. The current arm_smccc_(smc/hvc) is renamed and
macros are used instead to specify the standard arm_smccc_(smc/hvc) or
the arm_smccc_(smc/hvc)_quirk function.
This patch and partial implementation was suggested by Will Deacon.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building with debugging symbols, take the absolute path to the
vmlinux binary and add it to the special PE/COFF debug table entry.
This allows a debug EFI build to find the vmlinux binary, which is
very helpful in debugging, given that the offset where the Image is
first loaded by EFI is highly unpredictable.
On implementations of UEFI that choose to implement it, this
information is exposed via the EFI debug support table, which is a UEFI
configuration table that is accessible both by the firmware at boot time
and by the OS at runtime, and lists all PE/COFF images loaded by the
system.
The format of the NB10 Codeview entry is based on the definition used
by EDK2, which is our primary reference when it comes to the use of
PE/COFF in the context of UEFI firmware.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: use realpath instead of shell invocation, as discussed on list]
Signed-off-by: Will Deacon <will.deacon@arm.com>
We recently discovered that __raw_read_system_reg() erroneously mapped
sysreg IDs to the wrong registers.
To ensure that we don't get hit by a similar issue in future, this patch
makes __raw_read_system_reg() use a macro for each case statement,
ensuring that each case reads the correct register.
To ensure that this patch hasn't introduced an issue, I've binary-diffed
the object files before and after this patch. No code or data sections
differ (though some debug section differ due to line numbering
changing).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since it was introduced in commit da8d02d19f ("arm64/capabilities:
Make use of system wide safe value"), __raw_read_system_reg() has
erroneously mapped some sysreg IDs to other registers.
For the fields in ID_ISAR5_EL1, our local feature detection will be
erroneous. We may spuriously detect that a feature is uniformly
supported, or may fail to detect when it actually is, meaning some
compat hwcaps may be erroneous (or not enforced upon hotplug).
This patch corrects the erroneous entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: da8d02d19f ("arm64/capabilities: Make use of system wide safe value")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SPE buffer is virtually addressed, using the page tables of the CPU
MMU. Unusually, this means that the EL0/1 page table may be live whilst
we're executing at EL2 on non-VHE configurations. When VHE is in use,
we can use the same property to profile the guest behind its back.
This patch adds the relevant disabling and flushing code to KVM so that
the host can make use of SPE without corrupting guest memory, and any
attempts by a guest to use SPE will result in a trap.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of open-coding the loop, let's use canned macro.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
During a TLB invalidate sequence targeting the inner shareable domain,
Falkor may prematurely complete the DSB before all loads and stores using
the old translation are observed. Instruction fetches are not subject to
the conditions of this erratum. If the original code sequence includes
multiple TLB invalidate instructions followed by a single DSB, onle one of
the TLB instructions needs to be repeated to work around this erratum.
While the erratum only applies to cases in which the TLBI specifies the
inner-shareable domain (*IS form of TLBI) and the DSB is ISH form or
stronger (OSH, SYS), this changes applies the workaround overabundantly--
to local TLBI, DSB NSH sequences as well--for simplicity.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit cab15ce604 ("arm64: Introduce execute-only page access
permissions") allowed a valid user PTE to have the PTE_USER bit clear.
As a consequence, the pte_valid_not_user() macro in set_pte() was
replaced with pte_valid_global() under the assumption that only user
pages have the nG bit set. EFI mappings, however, also have the nG bit
set and set_pte() wrongly ignores issuing the DSB+ISB.
This patch reinstates the pte_valid_not_user() macro and adds the
PTE_UXN bit check since all kernel mappings have this bit set. For
clarity, pte_exec() is renamed to pte_user_exec() as it only checks for
the absence of PTE_UXN. Consequently, the user executable check in
set_pte_at() drops the pte_ng() test since pte_user_exec() is
sufficient.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If an EL0 instruction in the SYS class triggers an exception, do_sysintr
looks for a sys64_hook matching the instruction, and if none is found,
injects a SIGILL. This mirrors what we do for undefined instruction
encodings in do_undefinstr, where we look for an undef_hook matching the
instruction, and if none is found, inject a SIGILL.
Over time, new SYS instruction encodings may be allocated. Prior to
allocation, exceptions resulting from these would be handled by
do_undefinstr, whereas after allocation these may be handled by
do_sysintr.
To ensure that we have consistent behaviour if and when this happens, it
would be beneficial to have do_sysinstr fall back to do_undefinstr.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Refactor the KVM code to use the __tlbi macros, which will allow an errata
workaround that repeats tlbi dsb sequences to only change one location.
This is not intended to change the generated assembly and comparing before
and after vmlinux objdump shows no functional changes.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Define the MIDR implementer and part number field values for the Qualcomm
Datacenter Technologies Falkor processor version 1 in the usual manner.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When bypassing SWIOTLB on small-memory systems, we need to avoid calling
into swiotlb_dma_mapping_error() in exactly the same way as we avoid
swiotlb_dma_supported(), because the former also relies on SWIOTLB state
being initialised.
Under the assumptions for which we skip SWIOTLB, dma_map_{single,page}()
will only ever return the DMA-offset-adjusted physical address of the
page passed in, thus we can report success unconditionally.
Fixes: b67a8b29df ("arm64: mm: only initialize swiotlb when necessary")
CC: stable@vger.kernel.org
CC: Jisheng Zhang <jszhang@marvell.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix warning:
"(COMPAT) selects COMPAT_BINFMT_ELF which has unmet direct dependencies
(COMPAT && BINFMT_ELF)"
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Memory regions marked as NOMAP should not be used for general allocation
by the kernel, and should not even be covered by the linear mapping
(hence the name). However, drivers or other subsystems (such as ACPI)
that access the firmware directly may legally access them, which means
it is also reasonable for such drivers to claim them by invoking
request_resource(). Currently, this is prevented by the fact that arm64's
request_standard_resources() marks reserved regions as IORESOURCE_BUSY.
So drop the IORESOURCE_BUSY flag from these requests.
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If CONFIG_DEBUG_VIRTUAL=y and CONFIG_ARM64_SW_TTBR0_PAN=y:
virt_to_phys used for non-linear address: ffffff8008cc0000 (empty_zero_page+0x0/0x1000)
WARNING: CPU: 0 PID: 0 at arch/arm64/mm/physaddr.c:14 __virt_to_phys+0x28/0x60
...
[<ffffff800809abb4>] __virt_to_phys+0x28/0x60
[<ffffff8008a02600>] setup_arch+0x46c/0x4d4
Fixes: 2077be6783 ("arm64: Use __pa_symbol for kernel symbols")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 DMA-mapping implementation sets the DMA ops to the IOMMU DMA
ops if we detect that an IOMMU is present for the master and the DMA
ranges are valid.
In the case when the IOMMU domain for the device is not of type
IOMMU_DOMAIN_DMA, then we have no business swizzling the ops, since
we're not in control of the underlying address space. This patch leaves
the DMA ops alone for masters attached to non-DMA IOMMU domains.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in entry-ftrace.S, removing open-coded
sequences using adrp. This results in a minor code change, since a
temporary register is not used when generating the address for some
symbols, but this is fine, as the value of the temporary register is not
used elsewhere.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in efi-entry.S, removing open-coded
sequences using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of adr_l these in head.S, removing an open-coded
sequence using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The cache hierarchy can be identified through Cache Level ID(CLIDR)
architected system register. However in some cases it will provide
only the number of cache levels that are integrated into the processor
itself. In other words, it can't provide any information about the
caches that are external and/or transparent.
Some platforms require to export the information about all such external
caches to the userspace applications via the sysfs interface.
This patch adds support to override the cache levels using device tree
to take such external non-architected caches into account.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is useful to have helper function just to get the number of cache
levels for a given logical cpu. We can obtain the same by just checking
the level at which the last cache is present. This patch adds support
to find the level of the last cache for a given cpu.
It will be used on ARM64 platform where the device tree provides the
information for the additional non-architected/transparent/external
last level caches that are not integrated with the processors.
Cc: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Rob Herring <robh+dt@kernel.org>
Tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
[will: use u32 instead of int for cache_level]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Definition of cpu ranges are hard to read if the cpu variant is not
zero. Provide MIDR_CPU_VAR_REV() macro to describe the full hardware
revision of a cpu including variant and (minor) revision.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cosmetic change to use phys_addr_t instead of unsigned long for the
return value of __pa_symbol().
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM v8.1 extensions include support for rounding double multiply
add/subtract instructions to the A64 SIMD instructions set. Let
the userspace know about it via a HWCAP bit.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC attribute for
dma_{un}map_{page,sg} functions family to swiotlb.
DMA_ATTR_SKIP_CPU_SYNC allows platform code to skip synchronization of
the CPU cache for the given buffer assuming that it has been already
transferred to 'device' domain.
Ported from IOMMU .{un}map_{sg,page} ops.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
x86 has an option CONFIG_DEBUG_VIRTUAL to do additional checks
on virt_to_phys calls. The goal is to catch users who are calling
virt_to_phys on non-linear addresses immediately. This inclues callers
using virt_to_phys on image addresses instead of __pa_symbol. As features
such as CONFIG_VMAP_STACK get enabled for arm64, this becomes increasingly
important. Add checks to catch bad virt_to_phys usage.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
__pa_symbol is technically the marcro that should be used for kernel
symbols. Switch to this as a pre-requisite for DEBUG_VIRTUAL which
will do bounds checking.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
virt_to_pfn lacks a cast at the top level. Don't rely on __virt_to_phys
and explicitly cast to unsigned long.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Several macros for various x_to_y exist outside the bounds of an
__ASSEMBLY__ guard. Move them in preparation for support for
CONFIG_DEBUG_VIRTUAL.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Merge core DEBUG_VIRTUAL changes from Laura Abbott. Later arm and arm64
support depends on these.
* aarch64/for-next/debug-virtual:
drivers: firmware: psci: Use __pa_symbol for kernel symbol
mm/usercopy: Switch to using lm_alias
mm/kasan: Switch to using __pa_symbol and lm_alias
kexec: Switch to __pa_symbol
mm: Introduce lm_alias
mm/cma: Cleanup highmem check
lib/Kconfig.debug: Add ARCH_HAS_DEBUG_VIRTUAL
Documentation for the infrastructure to expose CPU feature
register by emulating MRS.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds the hook for emulating MRS instruction to
export the 'user visible' value of supported system registers.
We emulate only the following id space for system registers:
Op0=3, Op1=0, CRn=0, CRm=[0, 4-7]
The rest will fall back to SIGILL. This capability is also
advertised via a new HWCAP_CPUID.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[will: add missing static keyword to enable_mrs_emulation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Arnd Bergmann