The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports. To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]
er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.
If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.
We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.
Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".
Before the patch, we could perform an *erroneous* correction:
Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.
Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.
Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.
For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.
e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.
Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We turn the feature ON, only for servers with PCI BW < MAX LINK BW, as it
helps reducing PCI pressure on weak PCI slots, but it adds some software
overhead.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the MPWQE/Striding RQ default configuration dynamic and not
statically set at compile time. Now at driver load we set
stride size and num strides dynamically.
By default we use same values as before, but when CQE compression
is enabled, we set larger stride size to benefit from CQE
compression for larger packets.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ. By default
is disabled for now and will be enabled later on.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the one
contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:274:1: warning:
symbol 'socfpga_dwmac_pm_ops' was not declared. Should it be static?
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidently let Arnd's VXLAN dependency changes slip into net-next,
they are only appropriate for net.
Also the flow steering structural changes to mlx5e_priv got scrambled
during the merge resolution as well.
Fix that all up.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN can be disabled at compile-time or it can be a loadable
module while mlx5 is built-in, which leads to a link error:
drivers/net/built-in.o: In function `mlx5e_create_netdev':
ntb_netdev.c:(.text+0x106de4): undefined reference to `vxlan_get_rx_port'
This avoids the link error and makes the vxlan code optional,
like the other ethernet drivers do as well.
Link: https://patchwork.ozlabs.org/patch/589296/
Fixes: b3f63c3d5e ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 69976fb104.
We cannot select VXLAN when IPv4 support is disabled, that just gives
us additional build errors, including:
warning: (MLX5_CORE_EN) selects VXLAN which has unmet direct dependencies (NETDEVICES && NET_CORE && INET)
In file included from ../drivers/net/vxlan.c:36:0:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
include/net/udp_tunnel.h:112:9: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
return iptunnel_handle_offloads(skb, type);
^~~~~~~~~~~~~~~~~~~~~~~~
I'm sending a proper fix for the original bug in a separate patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the chip_reset() methods repeat the code writing to the ARSTR register
and delaying for 1 ms, so that we can reuse sh_eth_chip_reset() twice.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_chip_reset_giga() doesn't really need to use direct iowrite32() when
writing to the ARSTR register, it can use sh_eth_tsu_write() as all other
chip_reset() methods.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mdiobus_scan() doesn't return NULL on failure anymore, this driver
no longer needs to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"data_split" was never set to false. It's just uninitialized.
Fixes: 2950219d87 ('qede: Add basic network device support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling is broken here. netxen_rom_fast_read() returns zero
on success and -EIO on error. It never returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we are using "autoneg" without
initializing it. The problem is the ->phy_read() condition is reversed
so we only set this on error instead of success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complained that "v" can be used unintialized if
netxen_rom_fast_read() returns -EIO. That function never actually
returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cxgb4 is enabled with CONFIG_CHELSIO_T4_DCB set, VI enable command
gets called with DCB enabled. But when we have a back to back setup with
DCB enabled on one side and non-DCB on the Peer side. Firmware doesn't
send any DCB_L2_CFG, and DCB priority is never set for Tx queue.
But driver resets the queue priority and state machine whenever there
is a link down, this patch fixes it by adding a check to reset only if
cxgb4_dcb_enabled() returns true.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-05
This series contains updates to i40e and i40evf.
The theme behind this series is code reduction, yeah! Jesse provides
most of the changes starting with a refactor of the interpretation of
a tunnel which lets us start using the hardware's parsing. Removed
the packet split receive routine and ancillary code in preparation
for the Rx-refactor. The refactor of the receive routine,
aligns the receive routine with the one in ixgbe which was highly
optimized. The hardware supports a 16 byte descriptor for receive,
but the driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole lot
of complexity while getting rid of the code. Fixed a bug where while
changing the number of descriptors using ethtool, the driver did not
test the limits of the system memory before permanently assuming it
would be able to get receive buffer memory.
Mitch fixes a memory leak of one page each time the driver is opened by
allocating the correct number of receive buffers and do not fiddle with
next_to_use in the VF driver.
Arnd Bergmann fixed a indentation issue by adding the appropriate
curly braces in i40e_vc_config_promiscuous_mode_msg().
Julia Lawall fixed an issue found by Coccinelle, where i40e_client_ops
structure can be const since it is never modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.
As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.
This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently had a system crash in the cnic module. Vmcore analysis confirmed
that "ip link up" was executed which failed due to an allocation failure
because of memory fragmentation. Futher analysis revealed that the cnic irq
vector was still allocated after the "ip link up" that failed. When
"ip link down" was executed it called free_msi_irqs() which crashed the system
because the cnic irq was still inuse.
PANIC: "kernel BUG at drivers/pci/msi.c:411!"
The code execution was:
cnic_netdev_event()
if (event == NETDEV_UP) {
.
.
▹ if (!cnic_start_hw(dev))
cnic_start_hw()
calls cnic_cm_open() which failed with -ENOMEM
cnic_start_hw() then took the err1 path:
err1:↩
cp->free_resc(dev);↩ <---- frees resources but not irq vector
pci_dev_put(dev->pcidev);↩
return err;↩
}↩
This returns control back to cnic_netdev_event() but now the cnic irq vector
is still allocated even although cnic_cm_open() failed. The next
"ip link down" while trigger the crash.
The cnic_start_hw() routine is not handling the allocation failure correctly.
Fix this by checking whether CNIC_DRV_STATE_HANDLES_IRQ flag is set indicating
that the hardware has been started in cnic_start_hw(). If it has then call
cp->stop_hw() which frees the cnic irq vector and cnic resources. Otherwise
just maintain the previous behaviour and free cnic resources.
I reproduced this by injecting an ENOMEM error into cnic_cm_alloc_mem()s return
code.
# ip link set dev enpX down
# ip link set dev enpX up <--- hit's allocation failure
# ip link set dev enpX down <--- crashes here
With this patch I confirmed there was no crash in the reproducer.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newly added code in i40e_vc_config_promiscuous_mode_msg() is indented
in a way that gcc rightly complains about:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function 'i40e_vc_config_promiscuous_mode_msg':
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1543:4: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
if (f->vlan >= 0 && f->vlan <= I40E_MAX_VLANID)
^~
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1550:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'if'
aq_err = pf->hw.aq.asq_last_status;
From the context, it looks like the aq_err assignment was meant to be
inside of the conditional expression, so I'm adding the appropriate
curly braces now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5676a8b9cd ("i40e: Add VF promiscuous mode driver support")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When testing on systems with very limited amounts of RAM, a bug was
found where, while changing the number of descriptors using ethtool,
the driver didn't test the limits of system memory before permanently
assuming it would be able to get receive buffer memory.
Work around this issue by pre-allocation of the receive buffer
memory, in the "ghost" ring, which is then used during reinit
using the new ring length.
Change-Id: I92d7a5fb59a6c884b2efdd1ec652845f101c3359
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller