Add support for QCM2290 including a few prep changes.
* icc-qcm2290
interconnect: icc-rpm: Define ICC device type
interconnect: icc-rpm: Add QNOC type QoS support
interconnect: icc-rpm: Support child NoC device probe
dt-bindings: interconnect: Add Qualcomm QCM2290 NoC support
interconnect: qcom: Add QCM2290 driver support
Link: https://lore.kernel.org/r/20211215002324.1727-1-shawn.guo@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
It adds interconnect driver support for QCM2290 platform. The topology
consists of 3 NoCs: BIMC, Config NoC (CNOC) and System NoC (SNOC). SNOC
is a QCOM_ICC_QNOC type device, as well as its 3 virtual child devices,
QUP, MMNRT and MMRT. QUP is owned by RPM and thus has no .regmap_cfg,
while the other 2 share the same .regmap_cfg with SNOC (parent).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20211215002324.1727-6-shawn.guo@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
As shown in downstream DT[1], the System NoC of QCM2290 is modelled
using 4 fab/noc devices: sys_noc + qup_virt + mmnrt_virt + mmrt_virt.
Among those 3 virtual devices, qup is owned by RPM and has no regmap
resource, while mmnrt and mmrt are owned by AP and share the same
regmap as sys_noc. So it's logical to represent these virtual devices
as child nodes of sys_noc in DT, so that such configuration can be
supported with a couple of changes on qnoc_probe():
- If there are child nodes, populate them.
- If the device descriptor has .regmap_cfg but there is no IOMEM
resource for the device, use parent's regmap.
[1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/tags/android-11.0.0_r0.56/qcom/scuba-bus.dtsi
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20211215002324.1727-4-shawn.guo@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add driver for the Qualcomm interconnect buses found in SM8450 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
This is based on the downstream driver by
Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211209084842.189627-3-vkoul@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This series adds a driver for interconnects on MSM8996. This fixes some rare display underflows
and provides a slight heat reduction.
* icc-msm8996
dt-bindings: interconnect: Combine SDM660 bindings into RPM schema
interconnect: icc-rpm: Add support for bus power domain
dt-bindings: interconnect: Add Qualcomm MSM8996 DT bindings
interconnect: qcom: Add MSM8996 interconnect provider driver
Link: https://lore.kernel.org/r/20211021132329.234942-1-y.oudjana@protonmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Using icc-rpm on ARM32 currently results in clk_set_rate() errors during
boot, e.g. "bus clk_set_rate error: -22". This is very similar to commit
7381e27b1e ("interconnect: qcom: msm8974: Prevent integer overflow in rate")
where the u64 is converted to a signed long during clock rate rounding,
resulting in an overflow on 32-bit platforms.
Let's fix it similarly by making sure that the rate does not exceed
LONG_MAX. Such high clock rates will surely result in the maximum
frequency of the bus anyway.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211206114542.45325-1-stephan@gerhold.net
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
[georgi: remove icc_sync_state for platforms with incomplete support]
Link: https://lore.kernel.org/r/20211125174751.25317-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add a driver for the MSM8996 NoCs. This chip is similar to SDM660 where
some busses are controlled by RPM, while others directly by the AP with
writes to QoS registers.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20211021132329.234942-5-y.oudjana@protonmail.com
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add support for attaching to a power domain. This is required
for Aggregate 0 NoC on MSM8996, which is powered by a GDSC.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Link: https://lore.kernel.org/r/20211021132329.234942-3-y.oudjana@protonmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Drop DEFINE_QNODE macro which has become unused.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-12-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
To follow the example of the rest of icc-rpm.h drivers, expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-11-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Port support for AP-owned nodes from the downstream device tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-10-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation to adding AP-owned nodes support to msm8939 expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-9-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Port support for AP-owned nodes from the downstream device tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-8-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation to adding AP-owned nodes support to msm8916 expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-7-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
SDM660 driver expects to have QoS registers at the beginning of NoC
address space (sdm660 platform shifts NoC base address). Add support for
using QoS register offset, so that other platforms do not have to change
existing device trees.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-6-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Other RPM interconnect drivers might also use QoS support. Move AP-owned
nodes support from SDM660 driver to common icc-rpm.c.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-5-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Expand DEFINE_QNODE macros, which with an addition of QoS become an ugly
beast with tons of different arguments. While we are at it also move
links lists to separate arrays.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-3-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
All icc-rpm drivers use the same set of bus clocks. Move handling of bus
clocks to qnoc_probe. This both simplifies the code and allows using
qnoc_probe as device's probe function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-2-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Here are changes for the 5.15-rc1 merge window consisting of interconnect
core and driver updates.
Framework change:
- Add sanity check to detect if node is already added to provider.
Driver changes:
- RPMh drivers probe function consolidation
- Add driver for SC8180x platforms
- Add support for SC8180x OSM L3
- Use driver-specific naming in OSM L3
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=K/bk
-----END PGP SIGNATURE-----
Merge tag 'icc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.15
Here are changes for the 5.15-rc1 merge window consisting of interconnect
core and driver updates.
Framework change:
- Add sanity check to detect if node is already added to provider.
Driver changes:
- RPMh drivers probe function consolidation
- Add driver for SC8180x platforms
- Add support for SC8180x OSM L3
- Use driver-specific naming in OSM L3
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: osm-l3: Use driver-specific naming
interconnect: qcom: osm-l3: Add sc8180x support
dt-bindings: interconnect: Add SC8180x to OSM L3 DT binding
interconnect: qcom: Add SC8180x providers
dt-bindings: interconnect: Add Qualcomm SC8180x DT bindings
interconnect: Sanity check that node isn't already on list
interconnect: qcom: icc-rpmh: Consolidate probe functions
This reverts commit f84f5b6f72, which is
causing regressions on some platforms, preventing them to boot or do a
clean reboot. This is because the above commit is sending also all the
zero bandwidth requests to turn off any resources that might be enabled
unnecessarily, but currently this may turn off interconnects that are
enabled by default, but with no consumer to keep them on.
Let's revert this for now as some platforms are not ready for such
change yet. In the future we can introduce some _ignore_unused option
that could keep also the unused resources on platforms that have only
partial interconnect support and also add .shutdown callbacks to deal
with disabling the resources in the right order.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/CAE-0n52iVgX0JjjnYi=NDg49xP961p=+W5R2bmO+2xwRceFhfA@mail.gmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In situations were the developer screws up by e.g. not giving the OSM
nodes unique identifiers the interconnect framework might mix up nodes
between the OSM L3 provider and e.g. the RPMh provider.
The resulting callstack contains "qcom_icc_set", which is not unique to
the OSM L3 provider driver. Once the faulting qcom_icc_set() is
identified it's further confusing that "qcom_icc_node" is different
between the different drivers.
To avoid this confusion, rename the node struct and the setter in the
OSM L3 driver to include "osm_l3" in their names.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210725031414.3961227-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The SC8180x contains the usual RPMH based interconnect providers, add a
driver which defines the various busses and ports.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210723194243.3675795-2-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-5-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b59 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable]
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current probe/remove functions are implemented separately for each
target, but they are almost identical. Replace them with common
functions that can be used across all rpmh targets.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210621214241.13521-1-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Here are changes for the 5.14-rc1 merge window consisting of interconnect
driver updates.
Driver changes:
- New driver for SC7280 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ihE7
-----END PGP SIGNATURE-----
Merge tag 'icc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.14
Here are changes for the 5.14-rc1 merge window consisting of interconnect
driver updates.
Driver changes:
- New driver for SC7280 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: Add SC7280 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SC7280 DT bindings
Add driver for the Qualcomm interconnect buses found in SC7280 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-3-git-send-email-okukatla@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620704673-104205-1-git-send-email-zou_wei@huawei.com
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)
-----BEGIN PGP SIGNATURE-----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=wU6U
-----END PGP SIGNATURE-----
Merge tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
These are the interconnect changes for the 5.13-rc1 merge window
with the highlights being drivers for two new platforms.
Driver changes:
- New driver for SM8350 platforms.
- New driver for SDM660 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJgd/GZAAoJEIDQzArG2BZjJ3kP/jgsX2Z5J4/PqKgWaK8iFYs7
5DlDkX4Ogb61LXoAZrrKKAW8HLTKGrGB+AdfBMPT8nU865Js+EdWJXRrOmmPlaUn
CFYct8ABRfip38VLkfyv6LDbfd43lIk8c809JFQiLQ9uFZSy5ZW/Vvh9ZCsMCSF6
Id7hKNzevTM3i0U8mLYJyhvrQ2G5qQUiiuQNeUJxt6Cl2hdzsk13MhdL5pFYwdJA
WAEu3+Wcj3PeMo7+bWJO/VV5MswhHtYhS8hF/HsPYmtDTgNUkkMAXiFArBO1wB8H
RgRLPTOUcJq8YgqWYFoaAVn1Gp2SDWyCK/c0CcLuh/rILrpICCJrHPmoS3V/beJk
B+GPLilSN51KSvvkO/naiS/30lgF2a2355IXOfT4EKyEgVlmMmM8FmdfLkEfqQbI
nTT/mTDghrkCkx+n1mLu1T5o7kty+9PVAz6vz7N2evFSJrUC7VFhsY1ZKDPOBrgY
sr34SYS2SnkCyu32hga/nMKEqYmKLyY2WsQuDM0ExJP+MnvgzNj31fdXh6iRb9YB
34/smWyfBnzyIxIhL8bJiRvnHwIerLKdyCMzO2WMaBY436WeNK7xI38zMLqfpqs0
3ntatJeE1E9Y20FUWwdHuHIvqgL0cbw/0JqqdAqLoU8SmPi+nRX4XOFdVu0ckrTy
SXCb6lWCHVWDI0/kVYEp
=SguC
-----END PGP SIGNATURE-----
Merge tag 'icc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.13
These are the interconnect changes for the 5.13-rc1 merge window
with the highlights being drivers for two new platforms.
Driver changes:
- New driver for SM8350 platforms.
- New driver for SDM660 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sm8350: Add missing link between nodes
interconnect: qcom: sm8350: Use the correct ids
interconnect: qcom: sdm660: Fix kerneldoc warning
MAINTAINERS: icc: add interconnect tree
interconnect: qcom: Add SM8350 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SM8350 DT bindings
interconnect: qcom: icc-rpm: record slave RPM id in error log
interconnect: qcom: Add SDM660 interconnect provider driver
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
This patch series adds the SDM660 interconnect provider driver in
order to stop some timeouts and achieve some decent performance by
avoiding to be NoC limited.
It's also providing some power consumption improvement, but I have
only measured that as less heat, which is quite important when
working on thermally constrained devices like smartphones.
Please note that this driver's yaml binding is referring to a MMCC
clock, so this series does depend on the SDM660 MMCC driver that I
have sent separately.
The multimedia clock is required only for the Multimedia NoC (mnoc).
This patch series has been tested against the following devices:
- Sony Xperia XA2 Ultra (SDM630 Nile Discovery)
- Sony Xperia 10 (SDM630 Ganges Kirin)
- Sony Xperia 10 Plus (SDM636 Ganges Mermaid)
* icc-sdm660
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
interconnect: qcom: Add SDM660 interconnect provider driver
interconnect: qcom: sdm660: Fix kerneldoc warning
Link: https://lore.kernel.org/r/20201017133718.31327-1-kholk11@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is a link between the GEM NoC and C NoC nodes, which is currently
missing from the topology. Let's add it to allow consumers request paths
that use this link.
Reported-by: Alex Elder <elder@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094435.28937-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
For creating an array with the members for each NoC, we should be using
a local indexes, as otherwise unnecessary large arrays would be created.
Using an incorrect indexes will also result error for the consumers when
they try to find a valid path between the endpoints. Let's fix this and
use the correct ids.
Reported-by: Alex Elder <elder@linaro.org>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094334.28871-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SM8350 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Generated from downstream interconnect driver written by David Dai
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210318094617.951212-3-vkoul@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Georgi Djakov