Add binding document for serial bluetooth chips using
Nokia H4+ protocol.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For bluetooth protocol driver only supporting serdev it makes
sense to follow common practice and built them into their own
module.
Such modules need access to hci_uart_register_device and
hci_uart_tx_wakeup for using the common protocol helpers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device driver may need to communicate with the UART
device while the Bluetooth device is closed (e.g. due
to interrupts).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds library functions for serdev based BT drivers. This is largely
copied from hci_ldisc.c and modified to use serdev calls. There's a little
bit of duplication, but I avoided intermixing this as the ldisc code should
eventually go away.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
[Fix style issues reported by Pavel]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will be used by Nokia's H4+ protocol, which
uses 2-byte aligned packets.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add serdev helper functions for handling of cts and rts
lines using the serdev's tiocm functions.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add method, which waits until the transmission buffer has been sent.
Note, that the change in ttyport_write_wakeup is related, since
tty_wait_until_sent will hang without that change.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IPv6 stack needs to send and receive Neighbor Discovery
messages. Remove the IFF_POINTOPOINT flag.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make netdev queue packets if we run out of credits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Consolidate code sending data to LE CoC channels and adds proper
accounting of packets sent, the remaining credits and how many packets
are queued.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rely on netif_wake_queue and netif_stop_queue to flow control when
transmit resources are unavailable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since l2cap_chan_send will now queue the packets there is no point in
checking the credits anymore.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no point in setting IFF_NO_QUEUE should already have taken
care of setting it if tx_queue_len is not set, in fact this may
actually disable queue for interfaces that require it and do set
tx_queue_len.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just keep queueing them into TX queue since the caller might just have
to do the same and there is no impact in adding another packet to the
TX queue even if there aren't any credits to transmit them.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes should make it more clear why a packet is being dropped.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During chan_recv_cb there is already a peer lookup which can be passed
to recv_pkt directly instead of the channel.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sanity check of interrupt number in interrupt handler is unnecessary and
confusion, remove it.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A status field in the skb_cb struct was storing a channel status
based on channel suspend/resume events. This stored status was
then used to return EAGAIN if there were packet sending issues
in snd_pkt().
The issue is that the skb has been freed by the time the callback
to 6lowpan's suspend/resume was called. So, this generates a
"use after free" issue that was noticed while running kernel tests
with KASAN debug enabled.
Let's eliminate the status field entirely as we can use the channel
tx_credits to indicate whether we should return EAGAIN when handling
packets.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding 6lowpan devices very rapidly we sometimes see a crash:
[23122.306615] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0-43-arm64 #1 Debian 4.9.9.linaro.43-1
[23122.315400] Hardware name: HiKey Development Board (DT)
[23122.320623] task: ffff800075443080 task.stack: ffff800075484000
[23122.326551] PC is at expire_timers+0x70/0x150
[23122.330907] LR is at run_timer_softirq+0xa0/0x1a0
[23122.335616] pc : [<ffff000008142dd8>] lr : [<ffff000008142f58>] pstate: 600001c5
This was due to add_peer_chan() unconditionally initializing the
lowpan_btle_dev->notify_peers delayed work structure, even if the
lowpan_btle_dev passed into add_peer_chan() had previously been
initialized.
Normally, this would go unnoticed as the delayed work timer is set for
100 msec, however when calling add_peer_chan() faster than 100 msec it
clears out a previously queued delay work causing the crash above.
To fix this, let add_peer_chan() know when a new lowpan_btle_dev is passed
in so that it only performs the delay work initialization when needed.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 74cdad37cd ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ensure we don't end up with a null pointer dereferences by checking
for for allocation failures. Allocate by sizeof(*ptr) rather than
the type to fix checkpack warnings. Also merge multiple lines into
one line for the kmalloc call.
Detected by CoverityScan, CID#1422435 ("Dereference null return value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Else is not generally useful after a break or return
Signed-off-by: Prasanna Karthik <pkarthik@outlook.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The data from peer->chan->dst is not being copied to peer_addr, the
current code just updates the pointer and not the contents of what
it points to. Fix this with the intended assignment.
Detected by CoverityScan, CID#1422111 ("Parse warning
(PW.PARAM_SET_BUT_NOT_USED)")
Fixes: fb6f2f606ce8 ("6lowpan: Fix IID format for Bluetooth")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add driver source and config for softMAC implementation of Cascoda's CA8210
IEEE 802.15.4 transceiver device. The driver mimics a common PHY-only
implementation despite the CA8210 being a hardMAC device which exposes a SAP
interface to the fully integrated MAC.
The chip is a modem-only device with an integrated processor which runs the
802.15.4 MAC. The chip communicates via full-duplex SPI with additional pins
for NIRQ and NRESET. The chip can also output its 16MHz clock to a GPIO with a
configurable divider.
The driver can be configured to implement a debugfs node that provides access
to the SAP-based API to drive mechanisms not currently supported by the
standard kernel interface.
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Until now the driver supports only ACPI enumeration. Nevertheless
Intel Edison SoM has Broadcom Wi-Fi + BT chip and neither ACPI nor DT
enumeration mechanism.
Enable pure platform driver in order to support Intel Edison SoM.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The message concerning missing config files for 8723b, 8821a, and
8761a should have been issued with BT_INFO() rather than BT_ERR() as
this condition is not fatal. After looking at that code, I have
reworked the logic to log such messages only if the device needs such a
config file. At the moment, only the 8822b fits that description.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the initial connection interval recommended in Bluetooth
Specification v4.2 (30ms - 50ms).
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Variable err is being initialized to zero and then later being
set to the error return from the call to hci_req_run_skb; hence
we can remove the redundant initialization to zero.
Also on two occassions err is not being set from the error return
from the call to hci_req_run_skb, so add these missing assignments.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Intel Bluetooth device 9160/9260 also
known as ThunderPeak(ThP) for UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
This patch uses a hw_variant value read from the device during
runtime to form the firmware filenames instead of using a constant
value, so it can support multiple prouducts.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Multiple new hardware variants are planned and the simple if statement
would get really complicated and unreadable. So instead replace it with
a simple switch statement.
The change is applied to both USB and UART.
Based-on-patch-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C.
Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a race condition between a thread calling bt_accept_dequeue()
and a different thread calling bt_accept_unlink(). Protection against
concurrency is implemented using sk locking. However, sk locking causes
serialisation of the bt_accept_dequeue() and bt_accept_unlink() threads.
This serialisation can cause bt_accept_dequeue() to obtain the sk from the
parent list but becomes blocked waiting for the sk lock held by the
bt_accept_unlink() thread. bt_accept_unlink() unlinks sk and this thread
releases the sk lock unblocking bt_accept_dequeue() which potentially runs
bt_accept_unlink() again on the same sk causing a crash. The attempt to
double unlink the same sk from the parent list can cause a NULL pointer
dereference crash due to bt_sk(sk)->parent becoming NULL on the first
unlink, followed by the second unlink trying to execute
bt_sk(sk)->parent->sk_ack_backlog-- in bt_accept_unlink() which crashes.
When sk is in the parent list, bt_sk(sk)->parent will be not be NULL.
When sk is removed from the parent list, bt_sk(sk)->parent is set to
NULL. Therefore, add a defensive check for bt_sk(sk)->parent not being
NULL to ensure that sk is still in the parent list after the sk lock has
been taken in bt_accept_dequeue(). If bt_sk(sk)->parent is detected as
being NULL then restart the loop so that the loop variables are refreshed
to use the latest values. This is necessary as list_for_each_entry_safe()
is not thread safe so causing a risk of an infinite loop occurring as sk
could point to itself.
In addition, in bt_accept_dequeue() increase the sk reference count to
protect against early freeing of sk. Early freeing can be possible if the
bt_accept_unlink() thread calls l2cap_sock_kill() or rfcomm_sock_kill()
functions before bt_accept_dequeue() gets the sk lock.
For test purposes, the probability of failure can be increased by putting
a msleep of 1 second in bt_accept_dequeue() between getting the sk and
waiting for the sk lock. This exposes the fact that the loop
list_for_each_entry_safe(p, n, &bt_sk(parent)->accept_q) is not safe from
threads that unlink sk from the list in parallel with the loop which can
cause sk to become stale within the loop.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a small risk that bt_accept_unlink() runs concurrently with
bt_accept_enqueue() on the same socket. This scenario could potentially
lead to a NULL pointer dereference of the socket's parent member because
the socket can be on the list but the socket's parent member is not yet
updated by bt_accept_enqueue().
Therefore, add socket locking inside bt_accept_enqueue() so that the
socket is added to the list AND the parent's socket address is set in the
socket's parent member. The socket locking ensures that the socket is on
the list with a valid non-NULL parent member.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to RFC 7668 U/L bit shall not be used:
https://wiki.tools.ietf.org/html/rfc7668#section-3.2.2 [Page 10]:
In the figure, letter 'b' represents a bit from the
Bluetooth device address, copied as is without any changes on any
bit. This means that no bit in the IID indicates whether the
underlying Bluetooth device address is public or random.
|0 1|1 3|3 4|4 6|
|0 5|6 1|2 7|8 3|
+----------------+----------------+----------------+----------------+
|bbbbbbbbbbbbbbbb|bbbbbbbb11111111|11111110bbbbbbbb|bbbbbbbbbbbbbbbb|
+----------------+----------------+----------------+----------------+
Because of this the code cannot figure out the address type from the IP
address anymore thus it makes no sense to use peer_lookup_ba as it needs
the peer address type.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allow technologies such as Bluetooth to use its native lladdr which
is eui48 instead of eui64 which was expected by functions like
lowpan_header_decompress and lowpan_header_compress.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for 48 bit 6LoWPAN address length
autoconfiguration which is the case for BTLE 6LoWPAN.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The skb->pkt_type need to be set by L2, but on 6LoWPAN there exists L2
e.g. BTLE which doesn't has multicast addressing. If it's a multicast or
not is detected by IPHC headers multicast bit. The IPv6 layer will
evaluate this pkt_type, so we force set this type while uncompressing.
Should be okay for 802.15.4 as well.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set MAC address length according to the 6LoWPAN link layer in use.
Bluetooth Low Energy uses 48 bit addressing while IEEE802.15.4 uses
64 bits.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel