232275a USB: fix substandard locking for the sysfs files
introduced needed locking into sysfs operations on USB devices
It, however, uses uninterruptible sleep and if the error
handling is on extreme cases of sleep lengths of 10s of seconds
are possible. Unless we are removing the device we should use
interruptible sleep.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bus numbering is based on directly dealing with bitmaps and
defines a separate list of busses.
This can be simplified and unified by using existing idr functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
Crash log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0
Call Trace:
[<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140
[<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0
[<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0
[<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50
[<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710
[<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190
[<ffffffff81724743>] usb_reset_device+0x133/0x280
[<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70
[<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bus_to_hcd() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_usb_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbasename() helper is dedicated to find a last part of the filename or
pathname. USB core uses open-coded variant of that helper.
Replace some lines of code by kbasename() call.
The current users do not have trailing slash and we are on the safe side to
make such change. I dig a history of the code under question up and found the
patch [1] that brought it along with the same to tty layer. The check for
trailing slash looks like copy'n'paste thing and I consider it as redundant.
[1] http://www.kernel.org/pub/linux/kernel//people/akpm/patches/2.5/2.5.69/2.5.69-mm3/broken-out/linus.patch
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb 3.1 extend the hub get-port-status request by adding different
request types. the new request types return 4 additional bytes called
extended port status, these bytes are returned after the regular
portstatus and portchange values.
The extended port status contains a speed ID for the currently used
sublink speed. A table of supported Speed IDs with details about the link
is provided by the hub in the device descriptor BOS SuperSpeedPlus
device capability Sublink Speed Attributes.
Support this new request. Ask for the extended port status after port
reset if hub supports USB 3.1. If link is running at SuperSpeedPlus
set the device speed to USB_SPEED_SUPER_PLUS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way as SuperSpeed devices show "5000" as device speed we wan't to
show "10000" as the default speed for SuperSpeedPlus devices in sysfs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hcd roothub that supports HCD_USB31 is running at SuperSpeedPlus speed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing coccicheck warning which recommends to use memdup_user instead
to reimplement its code, using memdup_user simplifies the code
./drivers/usb/core/devio.c:1398:11-18: WARNING opportunity for memdup_user
Signed-off-by: Rahul Pathak <rpathak@visteon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed an unnecessary space between a function name and arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on
top of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates
of the ACPICA's copyright notices, a code fixup resulting from
a regression fix that was necessary in the upstream code only
(the regression fixed by it has never been present in Linux)
and a compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke
it on practically all architectures other than x86 and make a
couple of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether
or not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on
the problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up
a bit and update the MAINTAINERS information related to it
(Chanwoo Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJWoCQ4AAoJEILEb/54YlRxLscQALEFVKSRnNaco72OqqRZs9Bu
1RI6TgHTpZxR+Ef0+QWqE1QMnDwfImGhKDbSRm/t3S2sMYYZbAOL8cu4y6GmkBv4
bOon/f9WEoPlQCFoo/6U4u8H45rNT5W9zX5+Bva8x+4Wu3n2J1QdvirnS5JHeHe1
o6tGLaHuZXSwX8SLnCk8gJYK1VhATxbubJtpcVtvlnAhO11qUAwsscCrkUmB60i7
5hLyrZb06hoa/hZVcIefGFuSd9qPhzDMQE2M20EohQ7UVkNJQdY9QNHMqCk2P42T
nMWCNSwGnwfiO1p9ByXqunOFBCmyL7P+KV/DHsz6TFCVjz+jeG53Kqey9SkSJ/2W
iaAE80K9MfOMvg8j7rib6fTn5uXBwRfqdeUDF/Hr64QqJoRn3R2LX4HmZe4L8ufb
zA1rece67o8FD+7p7GkNbT3rPV/kA62tn/moFk446X5N+b261Kz90t1DVci8kRVf
k+1gcvEdqO0GPpEHoirfXrBvQFixqkXakKj4r2aAob/DldQeLX7CkOUuRRJ1ykec
bxwI9R0v8MlVe5rDxg+rPB0I9EFxRDmxqxpU5j0MRWxKnMRzLvBtHuk8YNVS/eU1
xwyJOGcwF6yI0PaCFggPqmhebSrWLE7wJxaK+3bC+yiDTvHYPjB+4MfQrmkRAwwM
azgb+ZgXDYx5wXeb8EjB
=bKJ9
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver
updates and fixes, like usual, and a mix of other USB driver updates as
well. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV2rUACgkQMUfUDdst+ym2XQCgqdDOlyGX5B//9CZ2kH1DrDW9
qLsAoLSBvw4hk+Aotv6tn8AayMpHwqV1
=pFLC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB drivers update for 4.5-rc1.
Lots of gadget driver updates and fixes, like usual, and a mix of
other USB driver updates as well. Full details in the shortlog. All
of these have been in linux-next for a while"
* tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits)
MAINTAINERS: change my email address
USB: usbmon: remove assignment from IS_ERR argument
USB: mxu11x0: drop redundant function name from error messages
USB: mxu11x0: fix debug-message typos
USB: mxu11x0: rename usb-serial driver
USB: mxu11x0: fix modem-control handling on B0-transitions
USB: mxu11x0: fix memory leak on firmware download
USB: mxu11x0: fix memory leak in port-probe error path
USB: serial: add Moxa UPORT 11x0 driver
USB: cp210x: add ID for ELV Marble Sound Board 1
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
usb: chipidea: host: set host to be null after hcd is freed
usb: chipidea: removing of_find_property
usb: chipidea: implement platform shutdown callback
usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference
usb: chipidea: delete static debug support
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
usb: chipidea: udc: improve error handling on _hardware_enqueue
usb: chipidea: udc: _ep_queue and _hw_queue cleanup
usb: dwc3: of-simple: fix build warning on !PM
...
Have dev_pm_ops.prepare return 1 for USB devices and ports so that USB
devices can remain runtime-suspended when the system goes to a sleep
state, if their wakeup state is correct and they have runtime PM enabled.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We want the USB and PHY fixes in here as well to make things easier for
testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8520f38099 ("USB: change hub initialization sleeps to
delayed_work") changed the hub_activate() routine to make part of it
run in a workqueue. However, the commit failed to take a reference to
the usb_hub structure or to lock the hub interface while doing so. As
a result, if a hub is plugged in and quickly unplugged before the work
routine can run, the routine will try to access memory that has been
deallocated. Or, if the hub is unplugged while the routine is
running, the memory may be deallocated while it is in active use.
This patch fixes the problem by taking a reference to the usb_hub at
the start of hub_activate() and releasing it at the end (when the work
is finished), and by locking the hub interface while the work routine
is running. It also adds a check at the start of the routine to see
if the hub has already been disconnected, in which nothing should be
done.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alexandru Cornea <alexandru.cornea@intel.com>
Tested-by: Alexandru Cornea <alexandru.cornea@intel.com>
Fixes: 8520f38099 ("USB: change hub initialization sleeps to delayed_work")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It shouldn't matter how usbcore is compiled. As it is a subsystem,
the correct way to use nousb should be usbcore.nousb
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently usb_port_resume waits for up to 2 seconds for CONNECT
status for SS devices only. This change will do the same thing for
non-SS devices even though the reason is a little different. This
will fix an issue where VBUS is turned off during system wide
"suspend to ram" and some 2.0 devices take greater than the current
max of 100ms to show connected after VBUS is enabled. This is most
commonly seen on hard drive based devices and USB3.0 devices plugged
into a 2.0 only port.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 LPM is default on in Linux kernel if both xHCI host controller
and the USB devices declare to be LPM-capable. Unfortunately, some
devices are known to work well with LPM disabled, but to be broken
if LPM is enabled, although it declares the LPM capability. Users
won't be able to use this kind of devices, until someone puts them
in the kernel blacklist and gets the kernel upgraded.
This patch adds a sysfs node to permit or forbit USB3 LPM U1 or U2
entry for a port. The settings apply to both before and after device
enumeration. Supported values are "0" - neither u1 nor u2 permitted,
"u1" - only u1 is permitted, "u2" - only u2 is permitted, "u1_u2" -
both u1 and u2 are permitted. With this interface, users can use an
LPM-unfriendly USB device on a released Linux kernel.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 655fe4effe ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_mon_operations structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch improves the usbfs_snoop debugging facility by adding
messages for a couple of significant events which, up to now, have not
been logged. The events are reaping and discarding (i.e.,
cancelling) an URB. The debugging messages include the userspace
address of the URB being reaped or discarded.
The reaping messages have to be added in four places, in order to
handle blocking and non-blocking reaps in both normal and 32-bit
compatibility mode.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbfs_snoop facility can be very useful for debugging problems
involving usbfs. However, it always prints out the entire contents of
every URB. When dealing with large quantities of data, this can be
less than helpful.
This patch ameliorates the situation by adding a module parameter to
usbcore for controlling the maximum number of bytes to print when
snooping an URB. This makes debugging much easier. For backward
compatibility, the default value is set unreasonably high.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When choose randconfig for kernel build, it reports below warning:
"warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG
which has unmet direct dependencies (USB_SUPPORT && USB && PM)"
In fact, USB_OTG is visible symbol and depends on PM, so the driver
needs to depend on it to reduce dependency problem.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete braces around single statement block suggested by checkpatch.pl
Signed-off-by: Jonas Hesselmann <jonas.hesselmann@hotmail.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'bDescriptorType' descriptor fields
while the values are #define'd in <linux/usb/ch9.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.
Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two headphones need a reset-resume quirk to properly resume to
original volume level.
Signed-off-by: Yao-Wen Mao <yaowen@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since a_alt_hnp_support is obsolete in OTG 2.0, HNP capable host should
send this set feature request only if the otg device is connecting to a
non-HNP port and it's compliant with OTG 1.x revision. This is done by
checking its otg descriptor length, OTG 2.0 uses usb_otg20_descriptor
which has different length than OTG 1.x using usb_otg_descriptor.
Signed-off-by: Li Jun <jun.li@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kmalloc_array instead of kmalloc to allocate memory for an array.
Also, remove the dev_warn for a memory leak, making the if check more
sleek.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the Sparse warning:
message.c:1390:21: warning: symbol 'i' shadows an earlier one
message.c:1294:13: originally declared here
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two occurrences of the Sparse warning:
warning: symbol XXX shadows an earlier one
Signed-off-by: Kris Borer <kborer@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed some checkpatch.pl warnings saying there was an unwanted space
between function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.1 Enhaned SuperSpeed can set their speed to
HCD_USB31 to let usb core and host drivers know that the controller
supports new USB 3.1 features.
make sure usb core handle HCD_USB31 hosts correctly, for now similar
to HCD_USB3.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device supports usb 3.1 SupeerSpeedPlus Gen2 speeds it povides
a SuperSpeedPlus device capability descriptor as a part of its
BOS descriptor. If we find one while parsing the BOS then save it
togeter with the other device capabilities found in the BOS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This introduces an attribute for each interface to
authorize (1) or deauthorize (0) it:
/sys/bus/usb/devices/INTERFACE/authorized
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel supports the device authorization because of wireless USB.
These is usable for wired USB devices, too.
These new interface authorization allows to enable or disable
individual interfaces instead a whole device.
If a deauthorized interface will be authorized so the driver probing must
be triggered manually by writing INTERFACE to /sys/bus/usb/drivers_probe
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver probings and interface claims get rejected
if an interface is not authorized.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bits 1:0 of the bmAttributes are used for the burst multiplier.
The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7
into use.
Use the existing USB_SS_MULT() macro instead to make sure the mult value
and hence max packet calculations are correct for USB3.1 devices.
Note that burst multiplier in bmAttributes is zero based and that
the USB_SS_MULT() macro adds one.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1d958bef45 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit de7718bd9c as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ef0909c50f as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 187b3d75bb as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3cf1fc8065 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed some checkpatch.pl warnings saying there was an unwanted space between
function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This introduces an attribute for each interface to
authorize (1) or deauthorize (0) it:
/sys/bus/usb/devices/INTERFACE/authorized
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel supports the device authorization because of wireless USB.
These is usable for wired USB devices, too.
These new interface authorization allows to enable or disable
individual interfaces instead a whole device.
If a deauthorized interface will be authorized so the driver probing must
be triggered manually by writing INTERFACE to /sys/bus/usb/drivers_probe
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver probings and interface claims get rejected
if an interface is not authorized.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix one occurrence of the checkpatch.pl error:
ERROR: do not use assignment in if condition
The semantic patch that makes this change is:
// <smpl>
@@
identifier i;
expression E, E2, E3;
statement S1, S2;
binary operator b;
@@
+ i = E;
if (
- (i = E)
+ i
b
... && E2 && E3 ) S1 else S2
// </smpl>
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix one occurrence of the checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix one occurrence of the checkpatch error:
ERROR: space prohibited before open square bracket '['
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed some checkpatch.pl warnings saying there was an unwanted space between
function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two occurrences of the checkpatch.pl error:
ERROR: space prohibited before that ',' (ctx:WxW)
Fix one occurrence of the checkpatch error:
ERROR: space required before the open parenthesis '('
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix five occurrences of the checkpatch.pl error:
ERROR: do not use assignment in if condition
The semantic patch that makes this change is:
// <smpl>
@@
identifier i;
expression E;
statement S1, S2;
@@
+ i = E;
if (
- (i = E)
+ i
) S1 else S2
@@
identifier i;
expression E;
statement S;
constant c;
binary operator b;
@@
+ i = E;
if (
- (i = E)
+ i
b
c ) S
// </smpl>
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a sysfs node to make it easier to verify if LPM is supported and being
enabled for USB 3.0 devices.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix four occurrences of checkpatch.pl error:
ERROR: do not use assignment in if condition
The semantic patch that makes this change is:
// <smpl>
@@
identifier i;
expression E;
statement S;
constant c;
binary operator b;
@@
+ i = E;
if (
- (i = E)
+ i
b
c ) S
@@
identifier i, i2;
expression E1, E2;
constant c;
@@
+ if( E1->i ) {
+ i2 = E2;
+ if (i2 < c) {
- if( E1->i && (i2 = E2) < c ) {
...
- }
+ }
+ }
// </smpl>
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 25cd2882e2 ("usb/xhci: Change how we indicate a host supports
Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed
root hub. The intention of that change was to avoid touching usb core
internal field, a.k.a. lpm_capable, and let usb core to set it by
checking U1 and U2 exit latency values in the descriptor.
Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately,
root hub is a special usb device as it has no parent. Hub_port_init()
will never be called for a root hub device. That means lpm_capable will
by no means be set for the root hub. As the result, lpm isn't functional
at all in Linux kernel.
This patch add the code to check and set lpm_capable when registering a
root hub device. It could be back-ported to kernels as old as v3.15,
that contains the Commit 25cd2882e2 ("usb/xhci: Change how we indicate
a host supports Link PM.").
Cc: stable@vger.kernel.org # 3.15
Reported-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.
Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().
Verbose Problem Description:
USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.
The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.
However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.
Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.
Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static checkers complain that the current condition is never true. It
seems pretty likely that it's a typo and "URB" was intended instead of
"USB".
Fixes: 3d97ff63f8 ('usbdevfs: Use scatter-gather lists for large bulk transfers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.
There are two major issues that the bus type is meant to
tackle:
Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.
Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Petr Mladek <pmladek@suse.cz>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Antoine Tenart <antoine.tenart@free-electrons.com>
CC: Petr Mladek <pmladek@suse.cz>
CC: Michal Sojka <sojka@merica.cz>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Fixed two warnings sizeof name and Blank line after declaration
Signed-off-by: Nizam Haider <nizamhaider786@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've had the same issue as described in commit
c68929f75d
Except my touchscreen's ID is
ID 04f3:0125 Elan Microelectronics Corp.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.01+ full-speed devices can have extended descriptor as well
and can support LPM.
Signed-off-by: Rupesh Tatiya <rtatiya@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Microsoft document "Using ACPI to Configure USB Ports on a Computer"
makes it clear that the removable flag will be cleared on ports that are
marked as unused by the firmware. Handle this case to match.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Windows appears to pay more attention to the ACPI values than any hub
configuration, so prefer the firmware's opinion on whether a port is
fixed or removable before falling back to the hub values.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ran checkpatch.pl on file and removed a warning about an unwanted space before
a tab.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move usb_disabled() and module_param()/core_param() towards the top of the file,
where 'nousb' is defined, as they are all related.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At few places we have used usb_disabled() and at other places used 'nousb'
directly. Lets be consistent and use usb_disabled();
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
In commit ceb6c9c862 ("USB / PM: Drop CONFIG_PM_RUNTIME from the
USB core"), all occurrences of CONFIG_PM_RUNTIME in the USB core
code were replaced by CONFIG_PM. This created the following structure
of #ifdef blocks in drivers/usb/core/hub.c:
[...]
#ifdef CONFIG_PM
#ifdef CONFIG_PM
/* always on / undead */
#else
/* dead */
#endif
[...]
This patch removes unnecessary inner "#ifdef CONFIG_PM" as well as
the corresponding dead #else block. This inconsistency was found using
the undertaker-checkpatch tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EHCI controller on the RK3288 SoC is violating basic parts of the
USB spec and thereby unable to properly resume a suspended port. It does
not start SOF generation within 3ms of finishing resume signaling, so
the attached device will drop of the bus again. This is a particular
problem with runtime PM, where accessing the device will trigger a
resume that immediately makes it unavailable (and reenumerate with a new
handle).
Thankfully, the persist feature is generally able to work around stuff
like that. Unfortunately, it doesn't quite work in this particular case
because the controller will turn off the CurrentConnectStatus bit for an
instant while the device is reconnecting, which causes the kernel to
conclude that it permanently disappeared. This patch adds a tiny retry
mechanism to the core port resume code which will catch this case and
shouldn't have any notable impact on other controllers.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This revert a82b76f7fa.
The commit causes an extra reset in remote wakeup as described in:
http://www.spinics.net/lists/linux-usb/msg119080.html
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors. The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.
This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.
This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd. The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nicolas Pitre <nico@linaro.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
The usbfs API has a peculiar hole: Users are not allowed to reap their
URBs after the device has been disconnected. There doesn't seem to be
any good reason for this; it is an ad-hoc inconsistency.
The patch allows users to issue the USBDEVFS_REAPURB and
USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts
on 64-bit systems) even after the device is gone. If no URBs are
pending for a disconnected device then the ioctls will return -ENODEV
rather than -EAGAIN, because obviously no new URBs will ever be able
to complete.
The patch also adds a new capability flag for
USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect
feature is supported.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Chris Dickens <christopher.a.dickens@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
OTG device shall support this device for allowing compliance automated testing.
The modification is derived from Pavankumar and Vijayavardhans' previous work.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if port power is turned off by user on hub port
using USBDEVFS then port power is turned back ON
by hub driver.
This commit modifies hub reset logic in hub_port_connect() to prevent
hub driver from turning back the port power ON if port is not owned
by kernel.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB stack provides a mechanism for drivers to request an
asynchronous device reset (usb_queue_reset_device()). The mechanism
uses a work item (reset_ws) embedded in the usb_interface structure
used by the driver, and the reset is carried out by a work queue
routine.
The asynchronous reset can race with driver unbinding. When this
happens, we try to cancel the queued reset before unbinding the
driver, on the theory that the driver won't care about any resets once
it is unbound.
However, thanks to the fact that lockdep now tracks work queue
accesses, this can provoke a lockdep warning in situations where the
device reset causes another interface's driver to be unbound; see
http://marc.info/?l=linux-usb&m=141893165203776&w=2
for an example. The reason is that the work routine for reset_ws in
one interface calls cancel_queued_work() for the reset_ws in another
interface. Lockdep thinks this might lead to a work routine trying to
cancel itself. The simplest solution is not to cancel queued resets
when unbinding drivers.
This means we now need to acquire a reference to the usb_interface
when queuing a reset_ws work item and to drop the reference when the
work routine finishes. We also need to make sure that the
usb_interface structure doesn't outlive its parent usb_device; this
means acquiring and dropping a reference when the interface is created
and destroyed.
In addition, cancelling a queued reset can fail (if the device is in
the middle of an earlier reset), and this can cause usb_reset_device()
to try to rebind an interface that has been deallocated (see
http://marc.info/?l=linux-usb&m=142175717016628&w=2 for details).
Acquiring the extra references prevents this failure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Reported-by: Olivier Sobrie <olivier@sobrie.be>
Tested-by: Olivier Sobrie <olivier@sobrie.be>
Cc: stable <stable@vger.kernel.org> # 3.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.
This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJUk0IDAAoJEILEb/54YlRx7fgP/3+yF/0TnEW93j2ALDAQFiLF
tSv2A2vQC8vtMJjjWx0z/HqPh86gfaReEFZmUJD/Q/e2LXEnxNZJ+QMjcekPVkDM
mTvcIMc2MR8vOA/oMkgxeaKregrrx7RkCfojd+NWZhVukkjl+mvBHgAnYjXRL+NZ
unDWGlbHG97vq/3kGjPYhDS00nxHblw8NHFBu5HL5RxwABdWoeZJITwqxXWyuPLw
nlqNWlOxmwvtSbw2VMKz0uof1nFHyQLykYsMG0ZsyayCRdWUZYkEqmE7GGpCLkLu
D6yfmlpen6ccIOsEAae0eXBt50IFY9Tihk5lovx1mZmci2SNRg29BqMI105wIn0u
8b8Ej7MNHp7yMxRpB5WfU90p/y7ioJns9guFZxY0CKaRnrI2+BLt3RscMi3MPI06
Cu2/WkSSa09fhDPA+pk+VDYsmWgyVawigesNmMP5/cvYO/yYywVRjOuO1k77qQGp
4dSpFYEHfpxinejZnVZOk2V9MkvSLoSMux6wPV0xM0IE1iD0ulVpHjTJrwp80ph4
+bfUFVr/vrD1y7EKbf1PD363ZKvJhWhvQWDgETsM1vgLf21PfWO7C2kflIAsWsdQ
1ukD5nCBRlP4K73hG7bdM6kRztXhUdR0SHg85/t0KB/ExiVqtcXIzB60D0G1lENd
QlKbq3O4lim1WGuhazQY
=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM (or even dropped in some cases).
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the USB core code
and documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUdJoNAAoJEIaOsuA1yqREqDoP/iwVojhk1qb2PQAJvLkl8To4
R34RM8zt8IRhE+yWIW8hm8xvsLiwvujBMgsphUmyu2k0X/NtPl1ElrDvObWwO0N8
ouyLISRw/wLUs8hJwsNVhIX0VjPxDQ6648C3OZYjySTtNtsh0rBw84ALX+IWkDye
Thb823xEunGYVwjhq8WrfT94q6LjyPp00XHlA4mf3XgSpXC2tKBFGmIcfmwObzYI
LkON7kJTp14XEeIYGYJO+7MBpo8s7YFmnpsDOV2QYlz/i0pRdjLwaKMN5T7D7DO5
YdvcQFQUM53dvq+tiw2k2iW4gmn9ktHHlckn8W5hhQZCs4ujSzYy/vP4GcbNEaTf
CuDocJGTr7ieU2IqYiTM+wRYavBoHLq9V5AHZmgsZ/pVF8lvG0hcX0fmd7XXScjv
GaKJqyQMaKZ9tRF9RZdMZeOrICp1X1X+KcqdG7yXoOtsVdn0O3zHdxYcZcVa29X/
cXuttoTywQgfrlI/uWWwpkYlqiHeawK1EooZ/6fYQDviLm4lrLPp94vF/5MqGM1j
f2tNpG63iOzLUUYJa+YgPqs6RrZLM3soZcf3bFAEt9sA99gc3ExwCYXurBEnTONr
XUowTfNKxPaVjNPZ1evGwF5F+WLEK4s88weB9lArd2S3NFP3DQV1cRpWj8rLYE72
lX6aWEWUDqnUHmwJUgIb
=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touchscreen needs the same quirk as the other models.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Bryan Poling <poli0048@umn.edu>
CC: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the integer variable 'feature' was not being used anywhere in the function.
so it is safe to remove the variable.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies the usb_authorize_device() function such as that it does
not reload the device descriptor for wired devices. The reasons for this
are as follows:
* Some devices dislike the master requesting the descriptor from them twice,
failing on the usb_get_device_descriptor() call with -ETIMEOUT. Observed this
on my Pretec 16GB flash drive (4146:ba65).
* Malicious device could send two different descriptors - one before
authorization, used by userspace to determine whether to authorize it and
second to be actually used by the kernel when determining which drivers to
bind.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the generic PHY support, analogous to the USB PHY support. Intended it to be
used with the PCI EHCI/OHCI drivers and the xHCI platform driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB PHY member of the HCD structure is renamed to 'usb_phy' and
modifications are done in all drivers accessing it.
This is in preparation to adding the generic PHY support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
[Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects,
updated changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code only returns -ENOTSUPP for OTG host, but in fact,
embedded host also needs to returns -ENOTSUPP if the peripheral
is not at TPL.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0cce2eda19
USB: fix LANGID=0 regression
defaults to a langid of 0x0409 if it's not properly implemented by the
device. Explain with a higher level error message what this means.
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch, USB activity can be signaled by blinking a LED. There
are two triggers, one for activity on USB host and one for USB gadget.
Both triggers should work with all host/device controllers. Tested only
with musb.
Performace: I measured performance overheads on ARM Cortex-A8 (TI
AM335x) running on 600 MHz.
Duration of usb_led_activity():
- with no LED attached to the trigger: 2 ± 1 µs
- with one GPIO LED attached to the trigger: 2 ± 1 µs or 8 ± 2 µs (two peaks in histogram)
Duration of functions calling usb_led_activity() (with this patch
applied and no LED attached to the trigger):
- __usb_hcd_giveback_urb(): 10 - 25 µs
- usb_gadget_giveback_request(): 2 - 6 µs
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that only choose_devnum() was not ready to process more hub
events at the same time.
All should be fine if we take bus->usb_address0_mutex there. It will
make sure that more devnums will not be chosen for the given bus and
the related devices at the same time.
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub started to use a workqueue instead of kthread. Let's make it clear from
the function names.
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have separate kthread for handling USB hub events.
It is more elegant to use the workqueue framework.
The workqueue is allocated as freezable because the original thread was
freezable as well.
Also it is allocated as ordered because the code is not ready for parallel
processing of hub events, see choose_devnum().
struct usb_hub is passed via the work item. Therefore we do not need
hub_event_list.
Also hub_thread() is not longer needed. It would call only hub_event().
The rest of the code did manipulate the kthread and it is handled by the
workqueue framework now.
kick_khubd is renamed to kick_hub_wq() to make the function clear. And the
protection against races is done another way, see below.
hub_event_lock has been removed. It cannot longer be used to protect struct
usb_hub between hub_event() and hub_disconnect(). Instead we need to get
hub->kref already in kick_hub_wq().
The lock is not really needed for the other scenarios as well. queue_work()
returns whether it succeeded. We could revert the needed operations
accordingly. This is enough to avoid duplicity and inconsistencies.
Yes, the removed lock causes that there is not longer such a strong
synchronization between scheduling the work and manipulating
hub->disconnected.
But kick_hub_wq() must never be called together with hub_disconnect()
otherwise even the original code would have failed. Any callers are
responsible for this.
Therefore the only problem is that hub_disconnect() could be called in parallel
with hub_event(). But this was possible even in the past. struct usb_hub is
still guarded by hub->kref and released in hub_events() when needed.
Note that the source file is still full of the obsolete "khubd" strings.
Let's remove them in a follow up patch. This patch already is complex enough.
Thanks a lot Alan Stern <stern@rowland.harvard.edu> for code review, many useful
tips and guidance. Also thanks to Tejun Heo <tj@kernel.org> for hints how to
allocate the workqueue.
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would like to convert khubd kthread to a workqueue. As a result hub_events()
will handle only one event per call.
In fact, we could do this already now because there is another cycle in
hub_thread(). It calls hub_events() until hub_event_list is empty.
This patch renames the function to hub_event(), removes the while cycle, and
renames the goto targets from loop* to out*.
When touching the code, it fixes also formatting of dev_err() and dev_dbg()
calls to make checkpatch.pl happy :-)
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is just a small optimization of the fix from the commit c605f3cdff
("usb: hub: take hub->hdev reference when processing from eventlist).
We do not need to take the reference for each event. Instead we could get it
when struct usb_hub is allocated and put it when it is released. By other words,
we could handle it the same way as the reference for hub->intfdev.
The motivation is that it will make the life easier when switching from khubd
kthread to a workqueue.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update configuration for USB_OTG_WHITELIST, any targeted hosts
(non PC-hosts) can have TPL (Targered Peripheral List).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.
The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd405d2a5 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a21 introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a21 "USB: set hub's default autosuspend delay as 0"
Cc: [3.8+] <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michael Welling <mwelling@emacinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/core/hub.c: In function 'usb_disconnect':
linux-2.6/drivers/usb/core/hub.c:2110: warning: 'hub' may be used uninitialized in this function
linux-2.6/drivers/usb/core/hub.c:2111: warning: 'port1' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [5ee0f803cc3a: usbcore: don't log on consecutive debounce
failures of the same port] added the check of the reliable port, but
it also replaced the device argument to dev_err() wrongly, which leads
to a NULL dereference.
This patch restores the right device, port_dev->dev. Also, since
dev_err() itself shows the port number, reduce the port number shown
in the error message, essentially reverting to the state before the
commit 5ee0f803cc.
[The fix suggested by Hannes, and the error message cleanup suggested
by Alan Stern]
Fixes: 5ee0f803cc ('usbcore: don't log on consecutive debounce failures of the same port')
Reported-by: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Section 4.4.7.2 "Interrupt Transfer Bandwidth Requirements" of the USB3.0 spec
says:
A zero-length data payload is a valid transfer and may be useful for
some implementations.
So, extend the logic of allowing URB_ZERO_PACKET to interrupt urbs too.
Otherwise, the kernel throws warning of BOGUS transfer flags.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am removing two fix mes in this file as after dicussing then it seems
there is no reason to check against Null for usb_device as it can never
be NULL and this is check is therefore not needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cd (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a host controller dies, we don't need to wait for a driver to
time out. We can shut down its URBs immediately. Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.
As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().
[ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 7.854658] usb 1-3: device descriptor read/64, error -71
[ 8.079657] usb 1-3: device descriptor read/64, error -71
[ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 8.414658] usb 1-3: device descriptor read/64, error -71
[ 8.639657] usb 1-3: device descriptor read/64, error -71
[ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.264598] usb 1-3: device not accepting address 3, error -71
[ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.784601] usb 1-3: device not accepting address 3, error -71
[ 9.784838] usb usb1-port3: device 1-3 not suspended yet
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resuming a powered down port sometimes results in the port state being
stuck in the training sequence.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
port1: can't get reconnection after setting port power on, status -110
hub 3-0:1.0: port 1 status 0000.02e0 after resume, -19
usb 3-1: can't resume, status -19
hub 3-0:1.0: logical disconnect on port 1
In the case above we wait for the port re-connect timeout of 2 seconds
and observe that the port status is USB_SS_PORT_LS_POLLING (although it
is likely toggling between this state and USB_SS_PORT_LS_RX_DETECT).
This is indicative of a case where the device is failing to progress the
link training state machine.
It is resolved by issuing a warm reset to get the hub and device link
state machines back in sync.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
usb usb3: port1 usb_port_runtime_resume requires warm reset
hub 3-0:1.0: port 1 not warm reset yet, waiting 50ms
usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
After a reconnect timeout when we expect the device to be present, force
a warm reset of the device. Note that we can not simply look at the
link status to determine if a warm reset is required as any of the
training states USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or
USB_SS_PORT_LS_COMP_MOD are valid states that do not indicate the need
for warm reset by themselves.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Ksenia Ragiadakou <burzalodowa@gmail.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sunil Joshi <joshi@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is disconnected, usb_unbind_interface is called, which
tries to enable and disable LPM. usb_enable_lpm also try to send a
control command SET SEL to the device.
Since device is already disconnected, therefore it does not make sense
to execute usb_(en/dis)able_lpm.
This patch returns from usb_(en/dis)able_lpm, if device was not in
default state atleast.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9262c19d14 "usb: disable port power control if not supported in
wHubCharacteristics" gated enabling runtime pm for usb_port devices on
whether the parent hub supports power control, which causes a
regression. The port must still be allowed to carry out runtime pm
callbacks and receive a -EAGAIN or -EBUSY result. Otherwise the
usb_port device will transition to the pm error state and trigger the
same for the child usb_device.
Prior to the offending commit usb_hub_create_port_device() arranged for
runtime pm to be disabled is dev_pm_qos_expose_flags() failed. Instead,
force the default state of PM_QOS_FLAG_NO_POWER_OFF flag to be set prior
to enabling runtime pm. If that policy can not be set then fail
registration.
Report: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Fixes: 9262c19d14 ("usb: disable port power control if not supported in wHubCharacteristics")
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where platform firmware has specified conflicting values for
port locations it is confusing and otherwise not helpful to throw a
backtrace. Instead, include enough information to determine that
firmware has done something wrong and globally disable port poweroff.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading through a recent bug report [1], Alan notes:
"Dan, the warning message in hub_suspend() should mention that the
child device isn't suspended yet."
...update the warning from:
"usb usb3-port4: not suspended yet"
...to:
"usb usb3-port4: device 3-4: not suspended yet"
[1]: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8521afe35 "usb: assign default peer ports for root hubs"
delayed marking a hub valid (set hdev->maxchild) until it had been fully
configured and to enable the publishing of valid hubs to be serialized
by usb_port_peer_mutex.
However, xhci_update_hub_device() in some cases depends on
hdev->maxchild already being set. Do the minimal fix and move it after
the setting of hdev->maxchild.
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unconditionally wake up the child device when the power session is
recovered.
This addresses the following scenarios:
1/ The device may need a reset on power-session loss, without this
change port power-on recovery exposes khubd to scenarios that
usb_port_resume() is set to handle. Prior to port power control the
only time a power session would be lost is during dpm_suspend of the
hub. In that scenario usb_port_resume() is guaranteed to be called
prior to khubd running for that port. With this change we wakeup the
child device as soon as possible (prior to khubd running again for this
port).
Although khubd has facilities to wake a child device it will only do
so if the portstatus / portchange indicates a suspend state. In the
case of port power control we are not coming from a hub-port-suspend
state. This implementation simply uses pm_request_resume() to wake the
device and relies on the port_dev->status_lock to prevent any collisions
between khubd and usb_port_resume().
2/ This mechanism rate limits port power toggling. The minimum port
power on/off period is now gated by the child device suspend/resume
latency. Empirically this mitigates devices downgrading their connection
on perceived instability of the host connection. This ratelimiting is
really only relevant to port power control testing, but it is a nice
side effect of closing the above race. Namely, the race of khubd for
the given port running while a usb_port_resume() event is pending.
3/ Going forward we are finding that power-session recovery requires
warm-resets (http://marc.info/?t=138659232900003&r=1&w=2). This
mechanism allows for warm-resets to be requested at the same point in
the resume path for hub dpm_suspend power session losses, or port
rpm_suspend power session losses.
4/ If the device *was* disconnected the only time we'll know for sure is
after a failed resume, so it's necessary for usb_port_runtime_resume()
to expedite a usb_port_resume() to clean up the removed device. The
reasoning for this is "least surprise" for the user. Turning on a port
means that hotplug detection is again enabled for the port, it is
surprising that devices that were removed while the port was off are not
disconnected until they are attempted to be used. As a user "why would
I try to use a device I removed from the system?"
1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume. For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.
Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control). Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().
Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device. To this end we hold the
port active with the "child_usage" reference across the disconnect
event. Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Alan:
"You mean from within hub_handle_remote_wakeup()? That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.
In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:
if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
udev->state != USB_STATE_NOTATTACHED) {
if (portstatus & USB_PORT_STAT_ENABLE) {
/* Nothing to do */
} else if (udev->state == USB_STATE_SUSPENDED &&
udev->persist_enabled) {
...
} else {
/* Don't resuscitate */;
}
}
...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.
So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset. The lock ordering
rules are now usb_lock_device() => usb_lock_port(). This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port. We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock. The lock is also dropped/re-acquired during
hub_port_reconnect().
This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it. Otherwise, the following sequence of events
leading to an unintended disconnect may occur:
Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5
Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.
We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.
This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.
Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
a matter of course
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state. There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection. Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.
By default the latency between peer power-on events is 0. In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay. In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.
Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates. Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value. If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs. External hubs follow the default peer
association scheme.
Location data is cached as an opaque cookie in usb_port_location data.
Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.
When we find port location data for a port then we assume that the
firmware will also describe its peer port. This allows the
implementation to only ever set the peer once. This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving. Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).
There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.
[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8
[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:
1/ ascend to the parent hub and find the upstream port_dev
2/ walk ->peer to find the peer port
3/ descend to the peer hub via ->child
4/ find the port with the matching port id
Note that this assumes the port labeling scheme required by the
specification [1].
[1]: usb3 3.1 section 10.3.3
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub. This identification scheme is required of
external hubs by the USB3 spec [1]. However, for root hubs, tier mismatch
may be in effect [2]. Tier mismatch can only be enumerated via platform
firmware. For now, simply perform the nominal association.
A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups. It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.
[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D
Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().
This also changes behavior in the case where the firmware says that the
port connect type is unknown. In that case just use the default setting
determined from the hub descriptor.
Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current port name "portX" is ambiguous. Before adding more port
messages rename ports to "<hub-device-name>-portX"
This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction. If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.
Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
dev_XXX(hub->intfdev, ..."port %d"...
dev_XXX(&hdev->dev, ..."port%d"...
into:
dev_XXX(&port_dev->dev, ...
Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb. However, it turns out that this
breaks 'lsusb -t'. For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".
Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor. If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine. However, since this does not save
power do not bother suspending.
This also consolidates support checks into a
hub_is_port_power_switchable() helper.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports. We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.
This patch fixes the problem by keeping track of when a reset is in
progress. At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately. When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch creates a separate instance of the usb_address0 mutex for each USB
bus, and attaches it to the usb_bus device struct. This allows devices on
separate buses to be enumerated in parallel; saving time.
In the current code, there is a single, global instance of the usb_address0
mutex which is used for all devices on all buses. This isn't completely
necessary, as this mutex is only needed to prevent address0 collisions for
devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage
can cause additional delay in system resume on systems with multiple hosts
(up to several seconds depending on what devices are attached).
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have already removed the usage of CONFIG_USB_DEBUG, it is
meaningless that there is still a configuration entry for CONFIG_USB_DEBUG.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again after call pci_enable_device().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all host controller drivers have bus-suspend and bus-resume
methods. When one doesn't, it will cause problems if runtime PM is
enabled in the kernel. The PM core will attempt to suspend the
controller's root hub, the suspend will fail because there is no
bus-suspend routine, and a -EBUSY error code will be returned to the
PM core. This will cause the suspend attempt to be repeated shortly
thereafter, in a never-ending loop.
Part of the problem is that the original error code -ENOENT gets
changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM
core will interpret -ENOENT as meaning that the root hub has gotten
into a runtime-PM error state. While this change is appropriate for
real USB devices, it's not such a good idea for a root hub. In fact,
considering the root hub to be in a runtime-PM error state would not
be far from the truth. Therefore this patch updates
usb_runtime_suspend() so that it adjusts error codes only for
non-root-hub devices.
Furthermore, the patch attempts to prevent the problem from occurring
in the first place by not enabling runtime PM by default for root hubs
whose host controller driver doesn't have bus_suspend and bus_resume
methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save someone else the debug cycles of figuring out why a driver's
transfer request is failing or causing undefined system behavior.
Buffers submitted for dma must come from GFP allocated / DMA-able
memory.
Return -EAGAIN matching the return value for dma_mapping_error() cases.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early. However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).
The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.
A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field. This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.
This patch should be applied to stable kernels from 3.10 onward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefani Seibold <stefani@seibold.net>
Tested-by: Stefani Seibold <stefani@seibold.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones added.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7BqAACgkQMUfUDdst+ykHUwCguJDlvM7/FGb3QQslAuKN5Np4
n2YAoJ3C355mo8Wxr/bJah3Jms4f+a7Q
=4XGY
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
Pull workqueue changes from Tejun Heo:
"PREPARE_[DELAYED_]WORK() were used to change the work function of work
items without fully reinitializing it; however, this makes workqueue
consider the work item as a different one from before and allows the
work item to start executing before the previous instance is finished
which can lead to extremely subtle issues which are painful to debug.
The interface has never been popular. This pull request contains
patches to remove existing usages and kill the interface. As one of
the changes was routed during the last devel cycle and another
depended on a pending change in nvme, for-3.15 contains a couple merge
commits.
In addition, interfaces which were deprecated quite a while ago -
__cancel_delayed_work() and WQ_NON_REENTRANT - are removed too"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove deprecated WQ_NON_REENTRANT
workqueue: Spelling s/instensive/intensive/
workqueue: remove PREPARE_[DELAYED_]WORK()
staging/fwserial: don't use PREPARE_WORK
afs: don't use PREPARE_WORK
nvme: don't use PREPARE_WORK
usb: don't use PREPARE_DELAYED_WORK
floppy: don't use PREPARE_[DELAYED_]WORK
ps3-vuart: don't use PREPARE_WORK
wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c
workqueue: Remove deprecated __cancel_delayed_work()
The USB_QUIRK_RESET flag indicates that a USB device changes its
identity in some way when it is reset. It may lose its firmware, its
descriptors may change, or it may switch back to a default mode of
operation.
If a device does this, the kernel needs to avoid resetting it. Resets
are likely to fail, or worse, succeed while changing the device's
state in a way the system can't detect.
This means we should disable the reset-resume mechanism whenever this
quirk flag is present. An attempted reset-resume will fail, the
device will be logically disconnected, and later on the hub driver
will rediscover and re-enumerate the device. This will cause the
appropriate udev events to be generated, so that userspace will have a
chance to switch the device into its normal operating mode, if
necessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.
The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled. If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.
This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.
The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: "Poulain, Loic" <loic.poulain@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue with drivers/staging/cxt1e1/linux.c that was
fixed in a report from Stephen Rothwell
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since it is needed outside usbcore and exposed in include/linux/usb.h,
it conflicts with enum dev_state in rt2x00 wireless driver.
Mark it as usb specific to avoid conflicts in the future.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device should not be able to be used concurrently both by
the server and the client. Claiming the port used by the
shared device ensures no interface drivers bind to it and
that it is not usable from the server.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
usb_hub->init_work is multiplexed with multiple work functions;
however, the work item is never queued while in-flight, so we can
simply use INIT_DELAYED_WORK() before each queueing.
It would probably be best to route this with other related updates
through the workqueue tree.
Lightly tested.
v2: Greg and Alan confirm that the work item is never queued while
in-flight. Simply use INIT_DELAYED_WORK().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
On disconnect USB3 protocol ports transit from U0 to SS.Inactive to Rx.Detect,
on a recoverable error, the port stays in SS.Inactive and we recover from it by
doing a warm-reset (through usb_device_reset if we have a udev for the port).
If this really is a disconnect we may end up trying the warm-reset anyways,
since khubd may run before the SS.Inactive to Rx.Detect transition, or it
may get skipped if the transition to Rx.Detect happens before khubd gets run.
With a loose connector, or in the case which actually led me to debugging this
bad ACPI firmware toggling Vbus off and on in quick succession, the port
may transition from Rx.Detect to U0 again before khubd gets run. In this case
the device state is unknown really, but khubd happily goes into the resuscitate
an existing device path, and the device driver never gets notified about the
device state being messed up.
If the above scenario happens with a streams using device, as soon as an urb
is submitted to an endpoint with streams, the following appears in dmesg:
ERROR Transfer event for disabled endpoint or incorrect stream ring
@0000000036807420 00000000 00000000 04000000 04078000
Notice how the TRB address is all zeros. I've seen this both on Intel
Pantherpoint and Nec xhci hosts.
Luckily we can detect the U0 to SS.Inactive to Rx.Detect to U0 all having
happened before khubd runs case since the C_LINK_STATE bit gets set in the
portchange bits on the U0 -> SS.Inactive change. This bit will also be set on
suspend / resume, but then it gets cleared by port_hub_init before khubd runs.
So if the C_LINK_STATE bit is set and a warm-reset is not needed, iow the port
is not still in SS.Inactive, and the port still has a connection, then the
device needs to be reset to put it back in a known state.
I've verified that doing the device reset also fixes the transfer event with
all zeros address issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If streams are still allocated on device-reset or set-interface then the hcd
code implictly frees the streams. Clear host_endpoint->streams in this case
so that if a driver later tries to re-allocate them it won't run afoul of the
device already having streams check in usb_alloc_streams().
Note normally streams still being allocated at reset / set-intf would be a
driver bug, but this can happen without it being a driver bug on reset-resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This allows userspace to use bulk-streams, just like in kernel drivers, see
Documentation/usb/bulk-streams.txt for details on the in kernel API. This
is exported pretty much one on one to userspace.
To use streams an app must first make a USBDEVFS_ALLOC_STREAMS ioctl,
on success this will return the number of streams available (which may be
less then requested). If there are n streams the app can then submit
usbdevfs_urb-s with their stream_id member set to 1-n to use a specific
stream. IE if USBDEVFS_ALLOC_STREAMS returns 4 then stream_id 1-4 can be
used.
When the app is done using streams it should call USBDEVFS_FREE_STREAMS
Note applications are advised to use libusb rather then using the
usbdevfs api directly. The latest version of libusb has support for streams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch makes it possible to specify a bulk stream id when submitting
an urb using the async usbfs API. It overloads the number_of_packets
usbdevfs_urb field for this. This is not pretty, but given other
constraints it is the best we can do. The reasoning leading to this goes
as follows:
1) We want to support bulk streams in the usbfs API
2) We do not want to extend the usbdevfs_urb struct with a new member, as
that would mean defining new ioctl numbers for all async API ioctls +
adding compat versions for the old ones (times 2 for 32 bit support)
3) 1 + 2 means we need to re-use an existing field
4) number_of_packets is only used for isoc urbs, and streams are bulk only
so it is the best (and only) candidate for re-using
Note that:
1) This patch only uses number_of_packets as stream_id if the app has
actually allocated streams on the ep, so that old apps which may have
garbage in there (as it was unused until now in the bulk case), will not
break
2) This patch does not add support for allocating / freeing bulk-streams, that
is done in a follow up patch
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding support for bulk streams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The usb_set_interface documentation says:
* Also, drivers must not change altsettings while urbs are scheduled for
* endpoints in that interface; all such urbs must first be completed
* (perhaps forced by unlinking).
For in kernel drivers we trust the drivers to get this right, but we
cannot trust userspace to get this right, so enforce it by killing any
urbs still pending on the interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Documentation/usb/bulk-streams.txt says:
All stream IDs will be deallocated when the driver releases the interface, to
ensure that drivers that don't support streams will be able to use the endpoint
This commit actually implements this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding support for bulk streams to usbfs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
So that it can be used in other places too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver currently uses a USB core internal field,
udev->lpm_capable, to indicate the xHCI driver knows how to calculate
the LPM timeout values. If this value is set for the host controller
udev, it means Link PM can be enabled for child devices under that host.
Change the code so the xHCI driver isn't mucking with USB core internal
fields. Instead, indicate the xHCI driver doesn't support Link PM on
this host by clearing the U1 and U2 exit latencies in the roothub
SuperSpeed Extended Capabilities BOS descriptor.
The code to check for the roothub setting U1 and U2 exit latencies to
zero will also disable LPM for external devices that do that same. This
was already effectively done with commit
ae8963adb4 "usb: Don't enable LPM if the
exit latency is zero." Leave that code in place, so that if a device
sets one exit latency value to zero, but the other is set to a valid
value, LPM is only enabled for the U1 or U2 state that had the valid
value. This is the same behavior the code had before.
Also, change messages about missing Link PM information from warning
level to info level. Only print a warning about the first device that
doesn't support LPM, to avoid log spam. Further, cleanup some
unnecessary line breaks to help people to grep for the error messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Better check the correct bit on big endian systems too. Shuts
up the following sparse __CHECK_ENDIAN__ warning:
.../hub.c:3965:32: warning: restricted __le32 degrades to integer
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error case isn't reported during enumeration.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is an error for a driver to call usb_clear_halt() or
usb_reset_endpoint() while there are URBs queued for the endpoint,
because the end result is not well defined. At the time the endpoint
gets reset, it may or may not be actively running.
As far as I know, no kernel drivers do this. But some userspace
drivers do, and it seems like a good idea to bring this error to their
attention.
This patch adds a warning to the kernel log whenever a program invokes
the USBDEVFS_CLEAR_HALT or USBDEVFS_RESETEP ioctls at an inappropriate
time, and includes the name of the program. This will make it clear
that any subsequent errors are not due to the misbehavior of a kernel
driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of Kconfig entries default to (uppercase) "N". It was clearly
intended to use "default n". But since (lowercase) "n" is the default
anyway, these lines might as well be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow the scheduler to select the best CPU to handle hub initalization
and LED blinking work. This extends idle residency times on idle CPUs
and conserves power.
This functionality is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.
[zoran.markovic@linaro.org: Rebased to latest kernel. Added commit message.
Changed reference from system to power efficient workqueue for LEDs in
check_highspeed() and hub_port_connect_change().]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Matthias Beyer <mail@beyermatthias.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Shaibal Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This modifies the probing order so that any matching
dynamic entry always will be used, even if the driver
has a matching static entry.
It is sometimes useful to dynamically update existing
device entries. With the new ability to set the dynamic
entry driver_info field, this can be used to test new
additions to class driver exception lists or proposed
changes to existing static per-device driver_info
entries.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was previously an interface driver. Since USB/IP
exports a whole device, not just an interface, it would make
sense to be a device driver.
This patch also modifies the way userspace sees and uses a
shared device:
* the usbip_status file is no longer created for interface 0, but for
the whole device (such as
/sys/devices/pci0000:00/0000:00:01.2/usb1/1-1/usbip_status).
* per interface information, such as interface class or protocol, is
no longer sent/received; only device specific information is
transmitted.
* since the driver was moved one level below in the USB architecture,
there is no need to bind/unbind each interface, just the device as a
whole.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a memory leak in the usb_store_new_id() error paths. When bailing out
due to sanity checks, the function left the already allocated usb_dynid
struct in place. This regression was introduced by the following commits:
c63fe8f6 (usb: core: add sanity checks when using bInterfaceClass with new_id)
1b9fb31f (usb: core: check for valid id_table when using the RefId feature)
52a6966c (usb: core: bail out if user gives an unknown RefId when using new_id)
Detected by Coverity: CID 1162604.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJS8UyYAAoJEBMGWMLi1Gc5G9AP/jTLQoh/9ILE3fPN9UeXHr7x
TR3sWrB2JB6HzO53FJqoIWdnyei+GQRHRYKFZbJRMIXSdfI7EiJ9ZaFvGKYkOjyg
FblD2WqYn5jY2yiW8roxOebDzDadxxqafwtrqIGx88sV9o9yKInhBq5NqxD1ZC/X
QM9Dbgxed4TX6OVVE8hvUbzr1gldYiUr8rKfvN8X6RDBEi6wh6HV0B/7T96vw6Hp
hFDIgIdwgVYsnah2QjS007tpNFfWQtoi3sq+Jcq0S6QVpCrTPjPB6MqHJM/MQtG+
8JkmZRPA8jjwaPvow8Kx3bmt89H5Q/hWKlUPZmaShOO4OKN3xOQNh+FNbvqs1pPZ
XpL3/dv/w/zzQ7sqD2IaT9HiDfzeYfspdiv9QsSJg7XlfiulgdCggrhIGvta6p51
bR0JEHMxSuI/Aqe/fr5Prf4YyeWS+fDKIwRsaNXG143pd7hFJxoyT91QE3FCxAdD
qmw/YdeDT7J+3TB55OCPIxuaOTEjJQ9GyKXP/TKaSrTVWcH8/N0wNMa7IPSplysN
fgeNNDtZ0A7P4XyyMNxaQpbRcM39eV/yGaVR6yDqjJ4RlEZTTTOMfNSaVoCXIb74
3km6DVSqEQ0xPq08nrIcWbPqor+hShbw/bbUJCQBITKJp6oDeImacCvZw7RaYhfs
cx7UuQPKmv7iYaG1Vmcm
=sPwW
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2014-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Fix some regressions introduced in 3.14.
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
Commit 9df89d85b4 "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.
Unfortunately, that's not the case. The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).
When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2
lspci for the affected host:
04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
Subsystem: 1043:1039
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at dd200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: xhci_hcd
Kernel modules: xhci_hcd
The commit was backported to stable kernels, and will need to be
reverted there as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Sergey Galanov <sergey.e.galanov@gmail.com>
Cc: stable@vger.kernel.org
When implementing the RefId feature, it was missed that id_tables can be
NULL under special circumstances. Bail out in that case.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If users use the new RefId feature of new_id, give them an error message
if they provided an unknown reference. That helps detecting typos.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if that field is actually used and if so, bail out if it exeeds a
u8. Make it also future-proof by not requiring "exactly three"
parameters in new_id, but simply "more than two".
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.
Signed-off-by: Shen Guang <shenguang10@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
BUG: unable to handle kernel NULL pointer dereference at 0000015c
IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d6082>] usb_set_device_state+0x92/0x120
[<c16d862b>] usb_disconnect+0x2b/0x1a0
[<c16dd4c0>] usb_remove_hcd+0xb0/0x160
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c1704efc>] ehci_mid_remove+0x1c/0x30
[<c1704f26>] ehci_mid_stop_host+0x16/0x30
[<c16f7698>] penwell_otg_work+0xd28/0x3520
[<c19c945b>] ? __schedule+0x39b/0x7f0
[<c19cdb9d>] ? sub_preempt_count+0x3d/0x50
[<c125e97d>] process_one_work+0x11d/0x3d0
[<c19c7f4d>] ? mutex_unlock+0xd/0x10
[<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
[<c125f009>] worker_thread+0xf9/0x320
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c125ef10>] ? rescuer_thread+0x2b0/0x2b0
[<c1264ac4>] kthread+0x94/0xa0
[<c19d0f77>] ret_from_kernel_thread+0x1b/0x28
[<c1264a30>] ? kthread_create_on_node+0xc0/0xc0
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_USB_DEBUG is going away, so remove the few places in the USB core
that relied on them.
This means that we always now do the "debug" checks for every urb
submitted, which is a good idea, as who knows how many driver bugs we
have been ignoring when people forget to enable this option. Also, with
the overall speed of USB, doing these extra checks should not cause any
additional overhead.
Also, no longer announce all devices being added to the system if
CONFIG_USB_DEBUG is enabled, as it's not going to be around much longer.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There is no need to skip querying the config and string descriptors for
unauthorized WUSB devices when usb_new_device is called. It is allowed
by WUSB spec. The only action that needs to be delayed until
authorization time is the set config. This change allows user mode
tools to see the config and string descriptors earlier in enumeration
which is needed for some WUSB devices to function properly on Android
systems. It also reduces the amount of divergent code paths needed
for WUSB devices.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_submit_urb, do not fail if an isoc URB for a wireless USB device
has an interval < 6. Per WUSB spec, isoc endpoints can support values
from 1-16. Valid values for interrupt URBs for wireless USB devices are
still 6-16.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 614ced91fc.
The units on this was seen were prototypes and the issue is
not seen on younger units.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds external USB phy support to USB HCD driver that
allows to find and initialize external USB phy, bound to
the HCD, when the HCD is added.
The usb_add_hcd function returns -EPROBE_DEFER if the USB
phy, bound to the HCD, is not ready.
If no USB phy is bound, the HCD is initialized as usual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>