BSpec says we shouldn't enable FBC on HSW/BDW when the pipe pixel rate
exceeds 95% of the core display clock.
v2:
- HSW also needs the WA (Ville).
- Add the WA name (Ville).
- Use the current cdclk (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And also print the threshold. I was surprised to see a log message
claiming the CFB size was 32mb when there was less than 24mb available
for it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FBC hardware for these platforms doesn't have access to the
bios_reserved range, so it always assumes the maximum (8mb) is used.
So avoid this range while allocating.
This solves a bunch of FIFO underruns that happen if you end up
putting the CFB in that memory range. On my machine, with 32mb of
stolen, I need a 2560x1440 mode for that.
Testcase: igt/kms_frontbuffer_tracking/fbc-* (given the right setup)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't allow FBC for cases where the spec says we can't FBC.
v2:
- Just WARN_ON() the strides that should have been caught earlier
(Daniel)
- Make it a new function since I expect this to grow more.
v3:
- Document which IGT test is exercised by this.
v4:
- Implement the restrictions for gens 2-6 too (Ville).
- Fix off-by-one mistake (Ville).
Testcase: igt/kms_frontbuffer_tracking/fbc-badstride
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always update the currrent crtc, fb and vertical offset after calling
enable_fbc. We were forgetting to do so along the failure paths when
enabling fbc synchronously. Fix this with a new helper to enable_fbc()
and update the state simultaneously.
v2: Improve commit message (Chris).
v3: Constify struct drm_framebuffer (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scaler_id in intel_pipe_config_compare should not be checked
when adjusting in intel_pipe_config_compare. The hw scaler id may
be changed in intel_update_pipe_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alex Dai <yu.dai@intel.com>
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable TO mode for RC6 for SKL till D0 and BXT till A0.
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
[danvet: Fixup line continuation alignment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes the warnings like
"plane A assertion failure, should be disabled but not"
that on the initial modeset during boot. This can happen if
the primary plane is enabled by the firmware, but inheriting
it fails because the DMAR is active or for other reasons.
Most likely caused by
commit 36750f284b
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 1 12:49:54 2015 +0200
drm/i915: update plane state during init
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91429
Reported-and-tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
WaRsDisableCoarsePowerGating: Coarse Power Gating (CPG) needs to be
disabled for platforms prior to BXT B0 and SKL GT3/GT4 till E0.
v2: Added GT3/GT4 Check.
Change-Id: Ia3c4c16e050c88d3e259f601054875c812d69c3a
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
[danvet: Align continuation properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be usefull to specify w/a that affects only SKL GT3 and GT4.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like this was introduced in:
commit d1675198ed
Author: Alex Dai <yu.dai@intel.com>
Date: Wed Aug 12 15:43:43 2015 +0100
drm/i915: Integrate GuC-based command submission
This patch assumed LRC contexts and HWS layout, which is incorrect on
platforms without execlists. This can lead to a crash in GPU error
state readout on those platforms.
I don't see a bug filed for this, but there may be one that I haven't
found.
v2: fixup offset handling for error capture fix (Dave)
Cc: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_modeset_readout_hw_state() seems like the more appropriate place
for populating the scanline_offset and timestamping constants than
intel_sanitize_crtc() since they are basically part of the state we
read out.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the sprite/cursor plane disabling to occur in intel_sanitize_crtc()
where it belongs instead of doing it in intel_modeset_readout_hw_state().
The plane disabling was first added in
4cf0ebbd4f drm/i915: Rework plane readout.
I got the idea from some patches from Partik and/or Maarten but those
moved also the plane state readout to intel_sanitize_crtc() which isn't
quite right in my opinion.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=91910
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dotclock is often calculated in encoder .get_config(), so we
shouldn't copy the adjusted_mode to hwmode until we have read out the
dotclock.
Gets rid of some warnings like these:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 21: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 0 is disabled
v2: Steal Maarten's idea to move crtc->mode etc. assignment too
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91428
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds two new functions:
- disable_dsi_pll.
BXT DSI disable sequence and registers are
different from previous platforms.
- intel_disable_dsi_pll
wrapper function to re-use the same code for
multiple platforms. It checks platform type and
calls appropriate core pll disable function.
v2: Fixed Jani's review comments.
v3: Rebased on latest drm-nightly branch.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BXT, We Observe timeout for forcewake request completion with 2ms polling period as given here:
[drm:fw_domains_get] ERROR render: timed out waiting for forcewake ack request.
Polling for 50ms is recommended to avoid these timeouts.
Change-Id: Ie715b0069a3049606e9602bc5e97a6511890864d
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable Turbo on steppings prior to B0 on BXT due to hangs seen during GT CPD exit.
Change-Id: I50c5c03f59f5ba092db19e17234951d89db42c6c
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modified HAS_CSR macro defination which earlier only supported
for skl, now added support for BXT.
v1: Initial version.
v2: Instaed of skylake/broxton check added gen9 check alone based
on review comment from Sunil.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added stepping info in intel_csr.c which is required to extract
specific firmware from packaged dmc firmware.
Stepping info is aligned with current bspec info.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broxton also has dmc to manage low-power display engine state.
Path of the firmware added in intel_csr.c.
Naming convention followed as <platform>_dmc_<api-version>.bin
v1: Initial version.
v2: Commit description added based on review comment from Sunil.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW at least (still testing other platforms, but should be harmless
elsewhere), the DSL reg reads back as 0 when read around vblank start
time. This ends up confusing the atomic start/end checking code, since
it causes the update to appear as if it crossed a frame count boundary.
Avoid the problem by making sure we don't return scanline_offset from
the get_crtc_scanline function. In moving the code there, I add to add
an additional delay since it could be called and have a legitimate 0
result for some time (depending on the pixel clock).
v2: move hsw dsl read hack to get_crtc_scanline (Ville)
v3: use break instead of goto (Ville)
update comment with workaround details (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Clearing the watermarks for all pipes/planes when updating the
watermarks for a single CRTC change seems like the wrong thing to
do here. As is, this code will ony update any pipe/plane watermarks
that need updating and leave the remaining set to zero. Later, the
watermark checks in check_wm_state() will flag these zero'd out pipe/plane
watermarks and throw errors.
By clearing only the watermark values associated with the specific crtc
the other watermark values may remain unchanged.
v2: Make sure all the dirty flags are cleared. Damien
Clear all values assoicated with crtc/pipe being updated. Damien
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want random people to touch these.
Especially true since we've just screwed up SKL by holding it way too
long under the preliminary flag because of some ABI issues. And now
there's howtos all over the internets about how to set this. Same
pretty much for anything else.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: drop fastboot changes, that option is gone.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds an "Overview" DOC section plus two DOC sections for the modes
of use ("Manual switching and manual power control" and "Driver power
control").
Also included is kernel-doc for all public functions, structs and enums.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL port E handling was added in
commit 26951caf55
Author: Xiong Zhang <xiong.y.zhang@intel.com>
Date: Mon Aug 17 15:55:50 2015 +0800
drm/i915/skl: enable DDI-E hotplug
but the whole function was moved in a another branch in
commit b93433ccf6
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Aug 20 10:47:36 2015 +0300
drm/i915: move ibx_digital_port_connected to intel_dp.c
and the addition was lost at some backmerge that I was unable to
identify. Put it back in.
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: No description found for parameter 'intel_encoder'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: Excess function parameter 'encoder' description in 'intel_audio_codec_disable'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: No description found for parameter 'intel_encoder'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: Excess function parameter 'encoder' description in 'intel_audio_codec_disable'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Not the first time! not the last time?
There is a possibility to use gcc 5's -Wbool-compare to try and compare
(reg) in those macros to a constant and gcc will warn that the
comparison between a boolean expression and a constant is always either
true or false. Maybe.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We allocate memory for LVDS modes while parsing the VBT at startup, but
never free this memory when the driver is unloaded, causing a small
leak.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use the new debug info in the intel_crtc struct in these functions
rather than passing them as args.
v2: move min/max assignment back above first trace call (Ville)
use scanline from crtc->debug rather than fetching a new one (Ville)
v3: fix up trace_i915_pipe_update_end, needs end scanline (Ville)
Requested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
ioremap_cache() is currently not available on some architectures.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vma'
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vmf'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'old'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'new'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'frontbuffer_bits'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
i915 supports enough atomic to have atomic fb-helper paths, even though
it does not yet advertise DRIVER_ATOMIC.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for using atomic code-paths for restore_fbdev_mode().
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Bikeshed comments slightly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
In the event that TTM doesn't find a compatible memory type for the
driver's first placement choice (placement without eviction), TTM
returns -EINVAL without trying the driver's second choice.
This causes problems on vmwgfx when VRAM is disabled before first modeset
and during VT switches when fbdev is not enabled.
Fix this by also trying the driver's second choice before returning
-EINVAL.
v2: Also check that man->use_type is true for the driver's second choice.
Fixes a bug where disallowed memory types could be used.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Shared frontbuffer bits are causing warnings when same FB is displayed
in another plane without clearing the bits from previous plane.
v2: Removing coversion of fb bits to 64 bit as it is not needed for now. (Daniel)
Change-Id: Ic2df80747f314b82afd22f8326297c57d1e652c6
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
[danvet: Drop INTEL_FRONTBUFFER_SPRITE_MASK since unused.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This stolen reserved stuff was introduced on g4x, so no need to waste
stolen on older platforms. Unfortunately configdb is no more so I can't
look up the right way to detect this stuff. I do have one hint as to
where the register might be on ctg, but I don't have a ctg to test it,
and on the elk I have here it doesn't contain sensible looking data.
For ilk grits suggegsts it might be in the same place as on snb (the
original PCI reg, not the mirror) but I can't be entirely sure about it
The register shows a round zero on my ilk.
So when there's no really good data for any of these platforms leave the
current "assume 1MiB" approach in place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fix following warnings while "make xmldocs".
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: No description
found for parameter 'req'
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: Excess function
parameter 'request' description in 'intel_logical_ring_begin'
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: Excess function
parameter 'ctx' description in 'intel_logical_ring_begin'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extend init/init_hw split to context init.
- Move context initialisation in to i915_gem_init_hw
- Move one off initialisation for render ring to
i915_gem_validate_context
- Move default context initialisation to logical_ring_init
Rename intel_lr_context_deferred_create to
intel_lr_context_deferred_alloc, to reflect reduced functionality &
alloc/init split.
This patch is intended to split out the allocation of resources &
initialisation to allow easier reuse of code for resume/gpu reset.
v2: Removed function ptr wrapping of do_switch_context (Daniel Vetter)
Left ->init_context int intel_lr_context_deferred_alloc
(Daniel Vetter)
Remove unnecessary init flag & ring type test. (Daniel Vetter)
Improve commit message (Daniel Vetter)
v3: On init/reinit, set the hw next sequence number to the sw next
sequence number. This is set to 1 at driver load time. This prevents
the seqno being reset on reinit (Chris Wilson)
v4: Set seqno back to ~0 - 0x1000 at start-of-day, and increment by 0x100
on reset.
This makes it obvious which bbs are which after a reset. (David Gordon
& John Harrison)
Rebase.
v5: Rebase. Fixed rebase breakage. Put context pinning in separate
function. Removed code churn. (Thomas Daniel)
v6: Cleanup up issues introduced in v2 & v5 (Thomas Daniel)
Issue: VIZ-4798
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This avoids some bad register writes and generally feels more correct
than unconditionally trying to redirect interrupts and such.
References: https://bugs.freedesktop.org/show_bug.cgi?id=91777
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use WARN_ONCE in a bunch of places and demote a message that would
continually spam us.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using intel_encoder's hpd_pin to check the live status
because of BXT A0/A1 WA for HPD pins and hpd_pin contains the
updated pin for the corresponding port.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When WaEnableForceRestoreInCtxtDescForVCS is required, it is only
safe to send new contexts if the last reported event is "active to
idle". Otherwise the same context can fully preempt itself because
lite-restore is disabled.
Testcase: igt/gem_concurrent_blit
Reported-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Tested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also check for correct revision id in each Gen9 platform (SKL until B0
and BXT until A0).
Cc: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Tested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the guest kernel side, previously the FIFO has been mapped write-
combined. This has worked since VMs up to now has not honored the mapping
type and mapped the FIFO cached anyway. Since the FIFO is accessed cached
by the CPU on the virtual device side, this leads to inconsistent
mappings once the guest starts to honor the mapping types.
So ask for cached mappings when we map the FIFO. We do this by
using ioremap_cache() instead of ioremap_wc(), and remove the MTRR setup.
On the TTM side, MOBs, GMRs and VRAM buffers are already requesting
cached mappings for kernel- and user-space.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
If user space calls unreference on a user_dmabuf it will typically
kill the struct ttm_base_object member which is responsible for the
user-space visibility. However the dmabuf part may still be alive and
refcounted. In some situations, like for shared guest-backed surface
referencing/opening, the driver may try to reference the
struct ttm_base_object member again, causing an immediate kernel warning
and a later kernel NULL pointer dereference.
Fix this by always maintaining a reference on the struct
ttm_base_object member, in situations where it might subsequently be
referenced.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
This is done as a separate commit, to make it easier to revert
when things break.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of doing a hack during primary plane commit the state
is updated during atomic evasion. It handles differences in
pipe size and the panel fitter.
This is continuing on top of Daniel's work to make faster
modesets atomic, and not yet enabled by default.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet:
- simplify/future-proof if ladder that Jesse spotted
- resolve conflict in pipe_config_check and don't spuriously move the
code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The initial state is read out correctly and the state is atomic,
so it's safe to preserve the fb without any hacks if it's suitable.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It should really use the atomic state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This might not have been set during boot, and when we preserve
the initial mode this can result in a black screen.
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since commit "drm/atomic-helper: Add option to update planes only on
active crtc" the drm_atomic_helper_commit_planes() function accepts an
active_only argument to skip updating planes when the associated CRTC is
inactive. Planes being disabled on an active CRTC are incorrectly
considered as associated with an inactive CRTC and are thus skipped,
preventing any plane disabling update from reaching drivers.
Fix it by checking the state of the CRTC stored in the old plane state
for planes being disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TEFw
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of patches that move part of the code used to allocate memory
from the media subsystem to the mm subsystem"
[ The mm parts have been acked by VM people, and the series was
apparently in -mm for a while - Linus ]
* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
[media] media: vb2: Remove unused functions
[media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
[media] vb2: Provide helpers for mapping virtual addresses
[media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
[media] mm: Provide new get_vaddr_frames() helper
[media] vb2: Push mmap_sem down to memops
Pull drm fixes from Dave Airlie:
"Just a bunch of fixes to squeeze in before -rc1:
- three nouveau regression fixes
- one qxl regression fix
- a bunch of i915 fixes
... and some core displayport/atomic fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
drm/qxl: validate monitors config modes
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
three nouveau regression fixes.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
Typo that snuck in with commit 6979c6303a
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Reported-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Broken since "gr: convert user classes to new-style nvkm_object"
Tested on a PPC64 G5 + NV34
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
bunch of drm fixes.
* tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel:
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Fixes headed for v4.3-rc1, including Maarten's DP MST state checker fix
you requested.
* tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Comment disagrees with the code which has changed a lot since
it was documented.
Note that the logic to remove -EIO handling was dropped in
commit 1488fc08c1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 24 15:47:31 2012 +0100
drm/i915: Remove the deferred-free list
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In async mode crtc->config can be updated after the locks are released,
resulting in the wrong state being duplicated.
Note that this also removes a spurious assignment of crtc_state->crtc
introduced in
commit f0c60574eb
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:12:58 2015 +0300
drm/i915: Call drm helpers when duplicating crtc and plane states
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the conversion to atomic this cannot happen any more.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately fbc still depends on legacy primary state, so
it can't be killed off completely yet.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function was still using the legacy state, convert it to atomic.
While we're at it, fix the FIXME too and disable the primary plane.
v2 (Daniel):
- Add FIXME explaining that update_primary_planes should soon get
removed anyway.
- Don't call ->disable_plane since we can't disable the primary plane
with a CS flip (noticed by Ville).
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Legacy state might not be updated any more.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the intel_connector initialized to intel_hdmi
display, during the init phase, just like the other encoders do.
This attachment is very useful when we need to extract the connector
pointer during the hotplug handler function
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like single link MIPI panels, similarly for dual link panels, pipe
to be configured is based on the DVO port from VBT Block 2. In hardware,
Port A is mapped with Pipe A and Port C is mapped with Pipe B.
This issue got introduced in -
commit 7e9804fdcf
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Jan 16 14:27:23 2015 +0200
drm/i915/dsi: add drm mipi dsi host support
Cc: stable@vger.kernel.org # v4.0
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.
Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix a wrong logical AND (&&) used for the range check of CSR MMIO.
Spotted nicely by gcc -Wlogical-op flag:
drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’:
drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op]
Fixes: eb805623d8 ('drm/i915/skl: Add support to load SKL CSR firmware.')
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This may cause issues because encoders are already destroyed so removing
active primaries may use freed memory. Instead free the fb directly,
ignoring refcount.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now, drm_sysfs_create() returns the newly allocated "struct class"
to the caller (which is drm_core_init()), which then has to set the
global variable 'drm_class'. During cleanup, though, we call
drm_sysfs_destroy() which implicitly uses the global 'drm_class'. This is
confusing, as ownership of the global 'drm_class' is non-obvious.
This patch changes drm_sysfs_create() to drm_sysfs_init() and makes it
initialize the 'drm_class' object directly, rather than returning it.
This way, both drm_sysfs_init() and drm_sysfs_destroy() work in a similar
fashion and manage the global drm class.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify `foo == NULL || IS_ERR(foo)` via IS_ERR_OR_NULL(). This is
pretty commonly used all over the kernel, especially for debugfs/sysfs
cleanup paths.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_av_sync_delay() doesn't change the passed in mode, so make it const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_select_eld() doesn't look at the passed in mode, so don't pass it
in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
valid_inferred_mode() don't change the modes over which it iterates,
so make the iterator const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When an i2c WRITE gets an i2c defer or short i2c ack reply, we are
supposed to switch the request from I2C_WRITE to I2C_WRITE_STATUS_UPDATE
when we continue to poll for the completion of the request.
v2: Don't assume DP_AUX_I2C_WRITE is 0 even though it is, to make the
code more obvious to the casual reader (Jani)
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict due to changed context.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A address-only I2C_WRITE can't be replied with a short i2c ack, but I
suppose it could be replied with an i2c defer. So the code should be
prepared for an address-only I2C_WRITE_STATUS_UPDATE.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we get an i2c defer or short ack for i2c-over-aux write we need
to switch to WRITE_STATUS_UPDATE to poll for the completion of the
original request.
Looks like radeon doesn't do anything special with the request type,
so hopefully just treating it the same as a i2c write is enough.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we get an i2c defer or short ack for i2c-over-aux write we need
to switch to WRITE_STATUS_UPDATE to poll for the completion of the
original request.
i915 doesn't try to interpret wht request type apart from separating
reads from writes, and so we should be able to treat this the same as
a normal i2c write.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Rename the I2C_STATUS request to I2C_WRITE_STATUS_UPDATE to match the
spec.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This function can be used to duplicate an atomic state object. This is
useful for example to implement suspend/resume, where the state before
suspend can be saved and restored upon resume.
v2: move locking to caller, be more explicit about prerequisites
v3: explicitly pass lock acquisition context, improve kerneldoc
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Requested by Laurent.
Note that this uses the new markdown support which will only land in
kernel 4.4 (for the code snippet).
v2: A few spelling fixes I spotted myself.
v3: Big reword for commit_planes() kerneldoc based on a text from
Laurent.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com> (v1 on irc)
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
connector->encoder is initialized as NULL. Fix this by setting it in
during pre enable. MST connectors are not read out during initial hw
readout, and have no fixed encoder mappings. So it's harmless to
return false when the connector has never been assigned to an encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With drivers supporting runtime pm it's generally not a good idea to
touch the hardware when it's off. Add an option to the commit_planes
helper to support this case.
Note that the helpers already add all planes on a crtc when a modeset
happens, hence plane updates will not be lost if drivers set this to
true.
v2: Check for NULL state->crtc before chasing the pointer. Also check
both old and new crtc if there's a switch. Finally just outright
disallow switching crtcs for a plane if the plane is in active use, on
most hardware that doesn't make sense.
v3: Since commit_planes(active_only = true) is for enabling things
only after all the crtc are on we should only look at the new crtc to
decide whether to call the plane hooks - if the current CRTC isn't on
then skip. If the old crtc (when moving a plane) went down then the
plane should have been disabled as part of the pipe shutdown work
already. For which there's currently no helper really unfortunately.
Also move the check for wether a plane gets a new CRTC assigned while
still in active use out of this patch.
v4: Rebase over exynos changes.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will make sure we get a lockdep spat in all cases
even if the context is a complete garbage pointer.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make generic_edid_names[] const since it's supposed to be immutable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow comma separated filenames in the edid_firmware parameter.
For example:
edid_firmware=eDP-1:edid/1280x480.bin,DP-2:edid/1920x1080.bin
v2: Use strsep() to simplify parsing of comma seperated string. (Matt)
Move initial bail before strdup. (Matt)
v3: Changed conditionals after while loop to make more readable (Jani)
Updated kernel-parameters.txt to reflect changes (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
[danvet: Flatten else control flow and appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Very strictly speaking this is possible if you have special hw and
genlocked CRTCs. In general switching a plane between two active CRTC
just won't work so well and is probably not tested at all. Just forbid
it.
I've put this into the core since right now no helper or driver copes
with it, no userspace has code for it and no one asks for it. Yes
there's piles of corner-cases where this would be possible to do this
like:
- switch from inactive crtc to active crtc
- switch from active crtc to inactive crtc
- genlocked display
- invisible plane (to do whatever)
- idle plane hw due to dsi cmd mode/psr
- whatever
but looking at details it's not that easy to implement this correctly.
Hence just put it into the core and add a comment, since the only
userspace we have right now for atomic (weston) doesn't want to use
direct plane switching either.
v2: don't bother with complexity and just outright disallow plane
switching without the intermediate OFF state. Simplifies drivers, we
don't have any hw that could do it anyway and current atomic userspace
(weston) works like this already anyway.
v3: Bikeshed function name (Ville) and add comment (Rob).
v4: Also bikeshed commit message (Rob).
v5: Fix compile warnings reported by 0-day.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Faster than recompiling.
Note that restore_fbdev_mode_unlocked is a bit special and the only
one which returns an error code when fbdev isn't there - i915 needs
that one to not fall over with some additional fbcon related restore
code. Everyone else just ignores the return value or only prints a
DRM_DEBUG level message.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions are used by drivers to release fbdev emulation
buffers. We need to make them resilient to NULL pointers to
make the fbdev compile/runtime knobs not cause Oopses on module
unload.
Cc: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using bool and returning true upon error is very uncommon. Also an int
return value is actually what all the callers which did check it seem
to have expected.
v2: Restore hunk misplaced in a rebase, spotted by Rob.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Without the () the markup and more important hyperlinking wont happen.
v2: Also fix nearby type Laurent spotted.
v3: Actually git add. Argh!
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The adj_start calculation for DRM_MM_CREATE_TOP should happen after
mm->color_adjust. There was an inconsistency between
drm_mm_insert_helper_range
and drm_mm_insert_helper, as the later was already updating after
color_adjust.
Didn't spot it before, as color_adjust is only done in systems without
LLC. But I'm not aware of anybody using this test case yet.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Legacy s/r hooks are only used for shadow-attaching drivers, warn
when a KMS driver tries to use them.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fall back to VBT based backlight modulation frequency if it's not
set. Do not hard code.
This could be a problem if there is no VBT.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the difference between backlight control on HSW vs. BDW/SKL is
that on HSW we modify the duty cycle on the CPU register, and have the
hardware pass the changes on to the PCH registers. We still drive the
PCH PWM on both. While HSW and BDW use the same LPT PCH, BDW does not
pass these messages on to the PCH. Therefore on BDW we need to enable
the PCH override bit, and program the PCH directly. (On SPT PCH, this
mode is the default.) We could as well do this on HSW too, and in fact
I've been told this is what a certain other operating system does. So
use PCH backlight override on HSW too.
This simplifies some follow-up code, but it does have the danger of
breaking backlight on HSW machines. It should work, but mysterious are
the ways of backlight.
While at it, name the related backlight hooks according to the PCH
rather than the CPU for clarity.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add stepping check for A0 workarounds, and remove the associated
FIXME tags.
Split out unrelated WAs for later condition checking.
v2: Fixed format (PeterL)
v3: Corrected stepping check for WaDisableSDEUnitClockGating
- Ignoring comment, following hardware spec instead. (ChrisH)
Added description for TILECTL setting (JonB)
Cc: Peter Lawthers <peter.lawthers@intel.com>
Cc: Chris Harris <chris.harris@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
A few more fixes for amdgpu from the last few days:
- Fix several copy paste typos
- Resume from suspend fixes for VCE
- Fix the GPU scheduler warning in kfifo_out
- Re-enable GPUVM fault interrupts which were inadvertently disabled
- GPUVM page table hang fix when paging
* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
It should be gfx_v8_0_init_compute_vmid since it's
part of the gfx block.
Acked-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to properly handle the instances for the idle
checks and soft reset.
Acked-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
it seems the VCE ring 1 ib test not reliable, remove it for now.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-and-Reviewed-by: Sonny Jiang <sonny.jiang@amd.com>
There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-
related changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition
is for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It
was initiated by lockdep warning, but resulted in a good cleanup in
the end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/sXs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
This time we have aded a new capability for scatter-gathered memset using
dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Others
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2 which is
deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gQZ6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
This should never happen so warn when the count does
not equal the expected size.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes regression from
commit f1afe24f0e
Author: Arun Siluvery <arun.siluvery@linux.intel.com>
Date: Tue Aug 4 16:22:20 2015 +0100
drm/i915: Change SRM, LRM instructions to use correct length
which forgot to account for the length bias when declaring the fixed
length.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91844
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pfit state is stored as register values, so dump them as hex instead
of decimal to make some sense of the error messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers exist only before GEN5, so currently we may access
undefined registers on VLV/CHV and BXT. Apply the workaround only pre
GEN5.
Since the workaround is relevant only when LVDS is present, for clarity
apply it only if this is the case.
This triggered an unclaimed register access warning on BXT.
v2: (Ville)
- move the workaround to the LVDS init code
- print a debug note about the workaround
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register exists only pre GEN5, but atm we also access it on
VLV/BXT/CHV. Prevent accessing it on these latter platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A small, very small, step to sharing the duplicate code between
execlists and legacy submission engines, starting with the ringbuffer
allocation code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TPS3 is mandatory for downstream devices that support HBR2, and Intel
platforms that support HBR2 also support TPS3. Whenever TPS3 is
supported by both the source and sink, it should be used. In other
words, whenever the source and sink are capable of 5.4 Gbps link, we
should anyway go for TPS3, regardless of the link rate being selected.
Log an error if the sink has advertized HBR2 capability without TPS3
capability.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is another case where we can consider the default is the
newest available and not actually a missed case.
No functional change.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unless future specs tells otherwise we can assume future gens
inherit some stuff from the previous so let's handle
missed cases when we know tehy should't be there and assume
default equals newest one.
No functional changes.
v2: Remove useless case as pointed out by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions are already being called for gen >= 9,
so let's be sure when this happens we use whatever is
there already for the latest platform.
No functional change.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On each call to gen8_alloc_va_range_3lvl we're allocating temporary
bitmaps needed for error handling. Unfortunately, when we increase
address space size (48b ppgtt) we do additional (512 - 4) calls to
kcalloc, increasing latency between exec and actual start of execution
on the GPU. Let's just do a single kcalloc, we can also drop the size
from free_gen8_temp_bitmaps since it's no longer used.
v2: Use GFP_TEMPORARY to make the allocations reclaimable.
v3: Drop the 2D array, just allocate a single block.
v4: Rebase to handle gen8_preallocate_top_level_pdps.
v5: Align misaligned bracket.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Correct kcalloc arguments as suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN >= 9 supports YUV format for all planes, but it's not exported in
Capability list of primary plane. Add YUV formats in skl_primary_formats
list.
Testcase: igt/kms_universal_plane.c
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Cc: Konduru, Chandra <chandra.konduru@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't rely on fb->bits_per_pixel as intel_framebuffer_init is not
filling bits_per_pixel field of fb-struct for YUV pixel format.
This leads to divide by zero error during watermark calculation.
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Cc: Konduru, Chandra <chandra.konduru@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915 display fixes headed for v4.3. Mostly SKL, but some regression
fixes too.
* tag 'drm-intel-next-fixes-2015-09-02' of git://anongit.freedesktop.org/drm-intel:
i915: Set ddi_pll_sel in DP MST path
drm/i915: Don't use link_bw for PLL setup
drm/i915: Preserve SSC earlier
drm/i915/skl: Adding DDI_E power well domain
drm/i915: eDP can be present on DDI-E
drm/i915/skl: Enable DDI-E
drm/i915: Enable HDMI on DDI-E
drm/i915: apply the PCI_D0/D3 hibernation workaround everywhere on pre GEN6
drm/i915: Check DP link status on long hpd too
drm/i915: set CDCLK if DPLL0 enabled during resuming from S3
Here are some fixes and some new features for rockchip drm,
tested on popmetal rk3288 board, can you land them?
* 'drm-rockchip-2015-08-26' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: vop: support plane scale
drm/rockchip: vop: restore vop registers when resume
drm/rockchip: vop: Default enable win2/3 area0 bit
drm/rockchip: vop: Add yuv plane support
drm/rockchip: vop: Fix window dest start point
drm/rockchip: vop: Fix virtual stride calculation
Pull request of 2015-09-01
A single commit. Workaround for
https://bugzilla.redhat.com/show_bug.cgi?id=1227193
* tag 'vmwgfx-next-15-09-01' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Allow dropped masters render-node like access on legacy nodes v2
This is a last pull request, which includes two g2d patches
I missed, and more cleanup series of Exynos drm driver.
The cleanup series makes Exynos drm driver more simple,
and removes unnecessary codes, and considers multiple plane format
of framebuffer. I hope this not to be late.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: remove buf_cnt from struct exynos_drm_fb
drm/exynos: remove exynos_drm_fb_get_buf_cnt()
drm/exynos: cleanup exynos_user_fb_create()
drm/exynos: update exynos_drm_framebuffer_init() for multiple buffers
drm/exynos: cleanup to get gem object for fb
drm/exynos: update fb_info via only one function
drm/exynos: cleanup exynos_drm_fbdev_update()
drm/exynos: s/exynos_gem_obj/obj in exynos_drm_fbdev.c
drm/exynos: remove exynos_drm_fb_set_buf_cnt()
drm/exynos: remove superfluous checks in g2d_check_reg_offset()
drm/exynos: fix size check in g2d_check_buf_desc_is_valid()
Paulo Zanoni